diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt | 145 |
1 files changed, 0 insertions, 145 deletions
diff --git a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt deleted file mode 100644 index 093edda0c8df..000000000000 --- a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt +++ /dev/null @@ -1,145 +0,0 @@ -Binding for Samsung S5M8767 regulator block -=========================================== - -This is a part of device tree bindings for S5M family multi-function devices. -More information can be found in bindings/mfd/sec-core.txt file. - -The S5M8767 device provide buck and LDO regulators. - -To register these with regulator framework instantiate under main device node -a sub-node named "regulators" with more sub-nodes for each regulator using the -common regulator binding documented in: - - Documentation/devicetree/bindings/regulator/regulator.txt - - -Required properties of the main device node (the parent!): - - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck2 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - - - s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck3 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - - - s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck4 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - - - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used - for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. - - [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' - property should specify atleast one voltage level (which would be a - safe operating voltage). - - If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, then all the eight voltage values for the - 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. - -Optional properties of the main device node (the parent!): - - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. - - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. - - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. - -Additional properties required if either of the optional properties are used: - - - s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from - the possible 8 options selectable by the dvs gpios. The value of this - property should be between 0 and 7. If not specified or if out of range, the - default value of this property is set to 0. - - - s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used - for dvs. The format of the gpio specifier depends in the gpio controller. - - -Names of regulators supported by S5M8767 device: - - LDOn - - valid values for n are 1 to 28 - - Example: LDO1, LDO2, LDO28 - - BUCKn - - valid values for n are 1 to 9. - - Example: BUCK1, BUCK2, BUCK9 -Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number -as per the datasheet of device. - - -Optional properties of the nodes under "regulators" sub-node: - - op_mode: describes the different operating modes of the LDO's with - power mode change in SOC. The different possible values are, - 0 - always off mode - 1 - on in normal mode - 2 - low power mode - 3 - suspend mode - - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one - GPIO controlling this regulator - (enable/disable); This is valid only - for buck9. - -Example: - - s5m8767_pmic@66 { - compatible = "samsung,s5m8767-pmic"; - reg = <0x66>; - - s5m8767,pmic-buck2-uses-gpio-dvs; - s5m8767,pmic-buck3-uses-gpio-dvs; - s5m8767,pmic-buck4-uses-gpio-dvs; - - s5m8767,pmic-buck-default-dvs-idx = <0>; - - s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ - <&gpx0 1 0>, /* DVS2 */ - <&gpx0 2 0>; /* DVS3 */ - - s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ - <&gpx2 4 0>, /* SET2 */ - <&gpx2 5 0>; /* SET3 */ - - s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, - <1250000>, <1200000>, - <1150000>, <1100000>, - <1000000>, <950000>; - - s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, - <1100000>, <1100000>, - <1000000>, <1000000>, - <1000000>, <1000000>; - - s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>; - - regulators { - ldo1_reg: LDO1 { - regulator-name = "VDD_ABB_3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - op_mode = <1>; /* Normal Mode */ - }; - - ldo2_reg: LDO2 { - regulator-name = "VDD_ALIVE_1.1V"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "VDD_MIF_1.2V"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - vemmc_reg: BUCK9 { - regulator-name = "VMEM_VDD_2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - op_mode = <3>; /* Standby Mode */ - s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>; - }; - }; - }; |