summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/freescale/mx6slevk/mx6slevk.c244
-rw-r--r--configs/mx6slevk_defconfig13
-rw-r--r--configs/mx6slevk_spinor_defconfig13
-rw-r--r--configs/mx6slevk_spl_defconfig2
-rw-r--r--include/configs/mx6slevk.h7
5 files changed, 130 insertions, 149 deletions
diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c
index 96c0e8cfc7..d49543315b 100644
--- a/board/freescale/mx6slevk/mx6slevk.c
+++ b/board/freescale/mx6slevk/mx6slevk.c
@@ -47,11 +47,6 @@ DECLARE_GLOBAL_DATA_PTR;
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\
PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
@@ -155,157 +150,55 @@ static void setup_iomux_fec(void)
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
/* Power up LAN8720 PHY */
+ gpio_request(ETH_PHY_POWER, "eth_pwr");
gpio_direction_output(ETH_PHY_POWER , 1);
udelay(15000);
}
-#define USDHC1_CD_GPIO IMX_GPIO_NR(4, 7)
-#define USDHC2_CD_GPIO IMX_GPIO_NR(5, 0)
-#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 22)
-
-static struct fsl_esdhc_cfg usdhc_cfg[3] = {
- {USDHC1_BASE_ADDR},
- {USDHC2_BASE_ADDR, 0, 4},
- {USDHC3_BASE_ADDR, 0, 4},
-};
-
int board_mmc_get_env_dev(int devno)
{
return devno;
}
-int board_mmc_getcd(struct mmc *mmc)
+#ifdef CONFIG_DM_PMIC_PFUZE100
+int power_init_board(void)
{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
+ struct udevice *dev;
+ int ret;
+ u32 dev_id, rev_id, i;
+ u32 switch_num = 6;
+ u32 offset = PFUZE100_SW1CMODE;
- switch (cfg->esdhc_base) {
- case USDHC1_BASE_ADDR:
- ret = !gpio_get_value(USDHC1_CD_GPIO);
- break;
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- ret = !gpio_get_value(USDHC3_CD_GPIO);
- break;
- }
-
- return ret;
-}
+ ret = pmic_get("pfuze100", &dev);
+ if (ret == -ENODEV)
+ return 0;
-int board_mmc_init(bd_t *bis)
-{
-#ifndef CONFIG_SPL_BUILD
- int i, ret;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 USDHC1
- * mmc1 USDHC2
- * mmc2 USDHC3
- */
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
- gpio_direction_input(USDHC1_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 2:
- imx_iomux_v3_setup_multiple_pads(
- usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- gpio_direction_input(USDHC3_CD_GPIO);
- usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) than supported by the board\n", i + 1);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret) {
- printf("Warning: failed to initialize "
- "mmc dev %d\n", i);
- return ret;
- }
- }
+ if (ret != 0)
+ return ret;
- return 0;
-#else
- struct src *src_regs = (struct src *)SRC_BASE_ADDR;
- u32 val;
- u32 port;
+ dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
+ rev_id = pmic_reg_read(dev, PFUZE100_REVID);
+ printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
- val = readl(&src_regs->sbmr1);
+ /* set SW1AB staby volatage 0.975V */
+ pmic_clrsetbits(dev, PFUZE100_SW1ABSTBY, 0x3f, 0x1b);
- /* Boot from USDHC */
- port = (val >> 11) & 0x3;
- switch (port) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
- ARRAY_SIZE(usdhc1_pads));
- gpio_direction_input(USDHC1_CD_GPIO);
- usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
- ARRAY_SIZE(usdhc2_pads));
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
- usdhc_cfg[0].max_bus_width = 4;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 2:
- imx_iomux_v3_setup_multiple_pads(usdhc3_pads,
- ARRAY_SIZE(usdhc3_pads));
- gpio_direction_input(USDHC3_CD_GPIO);
- usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
- usdhc_cfg[0].max_bus_width = 4;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- break;
- }
+ /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+ pmic_clrsetbits(dev, PFUZE100_SW1ABCONF, 0xc0, 0x40);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif
-}
+ /* set SW1C staby volatage 0.975V */
+ pmic_clrsetbits(dev, PFUZE100_SW1CSTBY, 0x3f, 0x1b);
-#ifdef CONFIG_SYS_I2C_MXC
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-/* I2C1 for PMIC */
-struct i2c_pads_info i2c_pad_info1 = {
- .sda = {
- .i2c_mode = MX6_PAD_I2C1_SDA__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_I2C1_SDA__GPIO_3_13 | PC,
- .gp = IMX_GPIO_NR(3, 13),
- },
- .scl = {
- .i2c_mode = MX6_PAD_I2C1_SCL__I2C1_SCL | PC,
- .gpio_mode = MX6_PAD_I2C1_SCL__GPIO_3_12 | PC,
- .gp = IMX_GPIO_NR(3, 12),
- },
-};
+ /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
+ pmic_clrsetbits(dev, PFUZE100_SW1CCONF, 0xc0, 0x40);
-int power_init_board(void)
-{
- struct pmic *p;
+ /* Init mode to APS_PFM */
+ pmic_reg_write(dev, PFUZE100_SW1ABMODE, APS_PFM);
- p = pfuze_common_init(I2C_PMIC);
- if (!p)
- return -ENODEV;
+ for (i = 0; i < switch_num - 1; i++)
+ pmic_reg_write(dev, offset + i * SWITCH_SIZE, APS_PFM);
- return pfuze_mode_init(p, APS_PFM);
+ return 0;
}
#endif
@@ -374,9 +267,7 @@ int board_ehci_hcd_init(int port)
int board_early_init_f(void)
{
setup_iomux_uart();
-#ifdef CONFIG_MXC_SPI
- setup_spi();
-#endif
+
return 0;
}
@@ -385,8 +276,9 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-#ifdef CONFIG_SYS_I2C_MXC
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+#ifdef CONFIG_MXC_SPI
+ gpio_request(IMX_GPIO_NR(4, 11), "spi_cs");
+ setup_spi();
#endif
#ifdef CONFIG_FEC_MXC
@@ -411,6 +303,76 @@ int checkboard(void)
#include <spl.h>
#include <libfdt.h>
+#define USDHC1_CD_GPIO IMX_GPIO_NR(4, 7)
+#define USDHC2_CD_GPIO IMX_GPIO_NR(5, 0)
+#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 22)
+
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+ {USDHC1_BASE_ADDR},
+ {USDHC2_BASE_ADDR, 0, 4},
+ {USDHC3_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC3_CD_GPIO);
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ struct src *src_regs = (struct src *)SRC_BASE_ADDR;
+ u32 val;
+ u32 port;
+
+ val = readl(&src_regs->sbmr1);
+
+ /* Boot from USDHC */
+ port = (val >> 11) & 0x3;
+ switch (port) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
+ ARRAY_SIZE(usdhc1_pads));
+ gpio_direction_input(USDHC1_CD_GPIO);
+ usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
+ ARRAY_SIZE(usdhc2_pads));
+ gpio_direction_input(USDHC2_CD_GPIO);
+ usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+ usdhc_cfg[0].max_bus_width = 4;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
+ case 2:
+ imx_iomux_v3_setup_multiple_pads(usdhc3_pads,
+ ARRAY_SIZE(usdhc3_pads));
+ gpio_direction_input(USDHC3_CD_GPIO);
+ usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
+ usdhc_cfg[0].max_bus_width = 4;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ break;
+ }
+
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
const struct mx6sl_iomux_ddr_regs mx6_ddr_ioregs = {
.dram_sdqs0 = 0x00003030,
.dram_sdqs1 = 0x00003030,
diff --git a/configs/mx6slevk_defconfig b/configs/mx6slevk_defconfig
index 42402c0935..fcacd21680 100644
--- a/configs/mx6slevk_defconfig
+++ b/configs/mx6slevk_defconfig
@@ -26,8 +26,21 @@ CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
CONFIG_DM=y
+# CONFIG_BLK is not set
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+# CONFIG_DM_MMC_OPS is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
CONFIG_DM_THERMAL=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
diff --git a/configs/mx6slevk_spinor_defconfig b/configs/mx6slevk_spinor_defconfig
index e03e0a7b9b..f9eba0c1f6 100644
--- a/configs/mx6slevk_spinor_defconfig
+++ b/configs/mx6slevk_spinor_defconfig
@@ -27,8 +27,21 @@ CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
CONFIG_DM=y
+# CONFIG_BLK is not set
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+# CONFIG_DM_MMC_OPS is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
CONFIG_DM_THERMAL=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
diff --git a/configs/mx6slevk_spl_defconfig b/configs/mx6slevk_spl_defconfig
index dcdc747f2e..7d3de1f943 100644
--- a/configs/mx6slevk_spl_defconfig
+++ b/configs/mx6slevk_spl_defconfig
@@ -8,7 +8,7 @@ CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,SPL,MX6SL"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,SPL,MX6SL,SYS_I2C"
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL=y
diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h
index 19dcc5cfb7..f5af65d761 100644
--- a/include/configs/mx6slevk.h
+++ b/include/configs/mx6slevk.h
@@ -27,19 +27,12 @@
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
/* I2C Configs */
-#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
-
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR