1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
|
* Freescale Fast Ethernet Controller (FEC)
Required properties:
- compatible : Should be "fsl,<soc>-fec"
- reg : Address and length of the register set for the device
- interrupts : Should contain fec interrupt
- phy-mode : See ethernet.txt file in the same directory
Optional properties:
- phy-reset-gpios : Should specify the gpio for phy reset
- phy-reset-duration : Reset duration in milliseconds. Should present
only if property "phy-reset-gpios" is available. Missing the property
will have the duration be 1 millisecond. Numbers greater than 1000 are
invalid and 1 millisecond will be used instead.
- phy-reset-active-high : If present then the reset sequence using the GPIO
specified in the "phy-reset-gpios" property is reversed (H=reset state,
L=operation state).
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
- phy-supply : regulator that powers the Ethernet PHY.
- phy-handle : phandle to the PHY device connected to this device.
- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
Use instead of phy-handle.
- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports
hw multi queues. Should specify the tx queue number, otherwise set tx queue
number to 1.
- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports
hw multi queues. Should specify the rx queue number, otherwise set rx queue
number to 1.
- fsl,magic-packet : If present, indicates that the hardware supports waking
up via magic packet.
- fsl,err006687-workaround-present: If present indicates that the system has
the hardware workaround for ERR006687 applied and does not need a software
workaround.
-interrupt-names: names of the interrupts listed in interrupts property in
the same order. The defaults if not specified are
__Number of interrupts__ __Default__
1 "int0"
2 "int0", "pps"
3 "int0", "int1", "int2"
4 "int0", "int1", "int2", "pps"
The order may be changed as long as they correspond to the interrupts
property. Currently, only i.mx7 uses "int1" and "int2". They correspond to
tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts.
For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse
per second interrupt associated with 1588 precision time protocol(PTP).
Optional subnodes:
- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes
according to phy.txt in the same directory
Example:
ethernet@83fec000 {
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
reg = <0x83fec000 0x4000>;
interrupts = <87>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */
local-mac-address = [00 04 9F 01 1B B9];
phy-supply = <®_fec_supply>;
};
Example with phy specified:
ethernet@83fec000 {
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
reg = <0x83fec000 0x4000>;
interrupts = <87>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */
local-mac-address = [00 04 9F 01 1B B9];
phy-supply = <®_fec_supply>;
phy-handle = <ðphy>;
mdio {
ethphy: ethernet-phy@6 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <6>;
max-speed = <100>;
};
};
};
|
