1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Analog Devices AD7606 Simultaneous Sampling ADC
maintainers:
- Beniamin Bia <beniamin.bia@analog.com>
- Stefan Popa <stefan.popa@analog.com>
description: |
Analog Devices AD7606 Simultaneous Sampling ADC
https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
properties:
compatible:
enum:
- adi,ad7605-4
- adi,ad7606-8
- adi,ad7606-6
- adi,ad7606-4
- adi,ad7606b
- adi,ad7616
reg:
maxItems: 1
spi-cpha: true
avcc-supply: true
interrupts:
maxItems: 1
adi,conversion-start-gpios:
description:
Must be the device tree identifier of the CONVST pin.
This logic input is used to initiate conversions on the analog
input channels. As the line is active high, it should be marked
GPIO_ACTIVE_HIGH.
maxItems: 1
reset-gpios:
description:
Must be the device tree identifier of the RESET pin. If specified,
it will be asserted during driver probe. As the line is active high,
it should be marked GPIO_ACTIVE_HIGH.
maxItems: 1
standby-gpios:
description:
Must be the device tree identifier of the STBY pin. This pin is used
to place the AD7606 into one of two power-down modes, Standby mode or
Shutdown mode. As the line is active low, it should be marked
GPIO_ACTIVE_LOW.
maxItems: 1
adi,first-data-gpios:
description:
Must be the device tree identifier of the FRSTDATA pin.
The FRSTDATA output indicates when the first channel, V1, is
being read back on either the parallel, byte or serial interface.
As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
maxItems: 1
adi,range-gpios:
description:
Must be the device tree identifier of the RANGE pin. The polarity on
this pin determines the input range of the analog input channels. If
this pin is tied to a logic high, the analog input range is ±10V for
all channels. If this pin is tied to a logic low, the analog input range
is ±5V for all channels. As the line is active high, it should be marked
GPIO_ACTIVE_HIGH.
maxItems: 1
adi,oversampling-ratio-gpios:
description:
Must be the device tree identifier of the over-sampling
mode pins. As the line is active high, it should be marked
GPIO_ACTIVE_HIGH.
maxItems: 1
adi,sw-mode:
description:
Software mode of operation, so far available only for ad7616 and ad7606b.
It is enabled when all three oversampling mode pins are connected to
high level. The device is configured by the corresponding registers. If the
adi,oversampling-ratio-gpios property is defined, then the driver will set the
oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
to VDD.
type: boolean
required:
- compatible
- reg
- spi-cpha
- avcc-supply
- interrupts
- adi,conversion-start-gpios
examples:
- |
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
spi0 {
#address-cells = <1>;
#size-cells = <0>;
adc@0 {
compatible = "adi,ad7606-8";
reg = <0>;
spi-max-frequency = <1000000>;
spi-cpol;
spi-cpha;
avcc-supply = <&adc_vref>;
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
interrupt-parent = <&gpio>;
adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
&gpio 23 GPIO_ACTIVE_HIGH
&gpio 26 GPIO_ACTIVE_HIGH>;
standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
adi,sw-mode;
};
};
...
|
