1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
|
Device-Tree bindings for LVDS Display Bridge (ldb)
LVDS Display Bridge
===================
The LVDS Display Bridge device tree node contains up to two lvds-channel
nodes describing each of the two LVDS encoder channels of the bridge.
Required properties:
- #address-cells : should be <1>
- #size-cells : should be <0>
- compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
Both LDB versions are similar, but i.MX6 has an additional
multiplexer in the front to select any of the four IPU display
interfaces as input for each LVDS channel.
- gpr : should be <&gpr> on i.MX53 and i.MX6q.
The phandle points to the iomuxc-gpr region containing the LVDS
control register.
- clocks, clock-names : phandles to the LDB divider and selector clocks and to
the display interface selector clocks, as described in
Documentation/devicetree/bindings/clock/clock-bindings.txt
The following clocks are expected on i.MX53:
"di0_pll" - LDB LVDS channel 0 mux
"di1_pll" - LDB LVDS channel 1 mux
"di0" - LDB LVDS channel 0 gate
"di1" - LDB LVDS channel 1 gate
"di0_sel" - IPU1 DI0 mux
"di1_sel" - IPU1 DI1 mux
On i.MX6q the following additional clocks are needed:
"di2_sel" - IPU2 DI0 mux
"di3_sel" - IPU2 DI1 mux
The needed clock numbers for each are documented in
Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
Documentation/devicetree/bindings/clock/imx6q-clock.txt.
Optional properties:
- pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
- pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
not used on i.MX6q
- fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
be configured - one input will be distributed on both outputs in dual
channel mode
LVDS Channel
============
Each LVDS Channel has to contain either an of graph link to a panel device node
or a display-timings node that describes the video timings for the connected
LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
Required properties:
- reg : should be <0> or <1>
- port: Input and output port nodes with endpoint definitions as defined in
Documentation/devicetree/bindings/graph.txt.
On i.MX5, the internal two-input-multiplexer is used. Due to hardware
limitations, only one input port (port@[0,1]) can be used for each channel
(lvds-channel@[0,1], respectively).
On i.MX6, there should be four input ports (port@[0-3]) that correspond
to the four LVDS multiplexer inputs.
A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
to a panel input port. Optionally, the output port can be left out if
display-timings are used instead.
Optional properties (required if display-timings are used):
- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- display-timings : A node that describes the display timings as defined in
Documentation/devicetree/bindings/display/panel/display-timing.txt.
- fsl,data-mapping : should be "spwg" or "jeida"
This describes how the color bits are laid out in the
serialized LVDS signal.
- fsl,data-width : should be <18> or <24>
example:
gpr: iomuxc-gpr@53fa8000 {
/* ... */
};
ldb: ldb@53fa8008 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx53-ldb";
gpr = <&gpr>;
clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
<&clks IMX5_CLK_LDB_DI1_SEL>,
<&clks IMX5_CLK_IPU_DI0_SEL>,
<&clks IMX5_CLK_IPU_DI1_SEL>,
<&clks IMX5_CLK_LDB_DI0_GATE>,
<&clks IMX5_CLK_LDB_DI1_GATE>;
clock-names = "di0_pll", "di1_pll",
"di0_sel", "di1_sel",
"di0", "di1";
/* Using an of-graph endpoint link to connect the panel */
lvds-channel@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
port@0 {
reg = <0>;
lvds0_in: endpoint {
remote-endpoint = <&ipu_di0_lvds0>;
};
};
port@2 {
reg = <2>;
lvds0_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
/* Using display-timings and fsl,data-mapping/width instead */
lvds-channel@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
display-timings {
/* ... */
};
port@1 {
reg = <1>;
lvds1_in: endpoint {
remote-endpoint = <&ipu_di1_lvds1>;
};
};
};
};
panel: lvds-panel {
/* ... */
port {
panel_in: endpoint {
remote-endpoint = <&lvds0_out>;
};
};
};
|
