| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
TAS2770 includes an ADC which reports the chip's die temperature.
As per the datasheet, the temperature in degrees Celsius is derived
by taking the raw value stored in the ADC's registers, dividing by 16,
then subtracting 93.
Create and register a hwmon device to expose the chip's die temperature
to the hwmon interface.
The ADC is shut down during software shutdown mode, and its registers
are initialised to 0 on reset. This means that the die temperature will
read -93 *C until the chip has been fully powered up at least once (e.g.
the PCM its attached to is opened). Once the chip is put into software
shutdown again, the ADC will also shut down. The last value sampled
before this happens will persist in the ADC's registers.
Co-developed-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250406-apple-codec-changes-v5-7-50a00ec850a3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We don't actually support configuring the PDM input right now. Rather,
this is useful as a hack.
On Apple Silicon machines, amps are split between two I2S buses which
are logically ANDed internally at the SoC. Odd and even slot groups are
driven by amps on either bus respectively. Since the signals are ANDed,
unused slot groups must be driven as zero to avoid corrupting the data
from the other side.
On most recent machines (TAS2764-based), this is accomplished using the
"SDOUT zero mask" feature of that chip. Unfortunately, TAS2770 does not
support this. It does support zeroing out *all* unused slots, which
works well for machines with a single amp per I2S bus. That is all,
except one.
The 13" M1 MacBook Pro is the only machine using TAS2770 and two amps
per I2S bus:
L Bus: SPK0I SPK0V Hi-Z Hi-Z SPK2I SPK2V Hi-Z Hi-Z
R Bus: Hi-Z Hi-Z SPK1I SPK2V Hi-Z Hi-Z SPK3I SPK3V
To ensure uncorrupted data, we need to force all the Hi-Z periods to
zero. We cannot use the "force all zero" feature, as that would cause a
bus conflict between both amps. We can use the pull-down feature, but
that leaves a few bits of garbage on the trailing edge of the speaker
data, since the pull-down is weak.
This is where the PDM transmit feature comes in. With PDM grounded and
disabled (the default state), the PDM slot is transmitted as all zeroes.
We can use that to force a zero 16-bit slot after the voltage data for
each speaker, cleaning it up. Then the pull-down ensures the line stays
low for the subsequent slot:
L Bus: SPK0I SPK0V PDM0 PulDn SPK2I SPK2V PDM0 PulDn
R Bus: PDM0 PulDn SPK1I SPK2V PDM0 PulDn SPK3I SPK3V
Yes, this is a horrible hack, but it beats adding dummy slots that would
be visible to the userspace capture side. There may be some other way to
fix the logical AND behavior on the MCA side... that would make this
unnecessary.
("How does Apple deal with this"? - they don't, macOS does not use
IVSENSE on TAS2770 machines even though it's physically wired up,
but we want to do so on Linux.)
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250406-apple-codec-changes-v5-2-50a00ec850a3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ISENSE/VSENSE blocks are only powered up when the amplifier
transitions from shutdown to active. This means that if those controls
are flipped on while the amplifier is already playing back audio, they
will have no effect.
Fix this by forcing a power cycle around transitions in those controls.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250406-apple-codec-changes-v5-1-50a00ec850a3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The former code sets the V slot from inside set_bitwidth according to
the bitwidth of the PCM format. That's wrong, since:
* It overrides the V slot parsed from DT binding.
* The V slot is set shifted behind the I slot by the length of the PCM
bitwidth, but the PCM bitwidth has no assured relation to the TDM
slot width.
Replace the former logic by setting up the I/V sense transmission only
in case of both I/V slots being specified in devicetree, and never
override those values. In case the slots are left unspecified, disable
the transmission completely.
There's an improbable case someone is relying on the old behavior, but
if so, that's a setup that only works by accident, and cannot be sanely
supported going forward. There's no indication anyone is consuming the
I/V sense data up to today, so break the former behavior.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-6-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a new explicit function for the setting of I/V sense TDM slots.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-5-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The scale starts at -100dB, not -128dB.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20250208-asoc-tas2770-v1-1-cf50ff1d59a3@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
These drivers all use <linux/gpio/consumer.h> and has no business
including the legacy headers <linux/gpio.h> or <linux/of_gpio.h>.
Drop the surplus includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20240807-asoc-tas-gpios-v2-3-bd0f2705d58b@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240605221446.2624964-2-andriy.shevchenko@linux.intel.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
i2c_device_id::driver_data to 0
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240502074722.1103986-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Link: https://lore.kernel.org/r/20230425095716.331419-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On probe of the ASoC component, the device is reset but the regcache is
retained. This means the regcache gets out of sync if the codec is
rebound to a sound card for a second time. Fix it by reinitializing the
regcache to defaults after the device is reset.
Fixes: b0bcbe615756 ("ASoC: tas2770: Fix calling reset in probe")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220919173453.84292-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Because the PWR_CTRL field is modeled as the power state of the DAC
widget, and at the same time it is used to implement mute/unmute, we
need some additional book-keeping to have the right end result no matter
the sequence of calls. Without this fix, one can mute an ongoing stream
by toggling a speaker pin control.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220808141246.5749-5-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver is setting the PWR_CTRL field in both the set_bias_level
callback and on DAPM events of the DAC widget (and also in the
mute_stream method). Drop the set_bias_level callback altogether as the
power setting it does is in conflict with the other code paths.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220808141246.5749-4-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The part is a mono speaker amp, but it can do downmix and switch between
left and right channel, so the right channel range is 1 to 2.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220808141246.5749-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix setting of FSYNC polarity for DAI formats other than I2S. Also
add support for polarity inversion.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220808141246.5749-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ASoC core has now been changed to default to the non-legacy DAI
naming, as such drivers using the new scheme no longer need to specify
the non_legacy_dai_naming flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623125250.2355471-61-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As part of moving to remove the old style defines for the bus clocks update
the tas2770 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220602135316.3554400-9-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
This avoids scanning the identifier tables during probes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220405165836.2165310-11-steve@sk2.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Per TAS2770 datasheet there must be a 1 ms delay from reset to first
command. So insert delays into the driver where appropriate.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220204095301.5554-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Although the codec advertises support for 176.4 and 192 ksps, without
this fix setting those sample rates fails with EINVAL at hw_params time.
Signed-off-by: Martin Povišer <povik@protonmail.com>
Link: https://lore.kernel.org/r/20211206224529.74656-1-povik@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062646.803053-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cppcheck warning:
sound/soc/codecs/tas2770.c:109:10: style: Variable 'ret' is assigned a
value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-22-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch syncs naming rule.
- xxx_rates;
+ xxx_rate;
- xxx_samplebits;
+ xxx_sample_bits;
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877doeolgk.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove unused variables in the private struct and the code as these
variables are initially set and then there is no additional code
utilizing these variables.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-6-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the code to support the asi-format binding property. The code
does nothing except read the property and set a variable. No additional
action is taken except to reset the variable. The property is supposed
to set the rising or falling RX edge detection of the SBCLK but this
edge detection is done by checking the DAI_FMT_INV_MASK.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-5-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the regcache to cache data and mark cache as dirty when the device
is shutdown when suspend is called. When the device is woken up then
sync the cache and set to not caching the data.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-3-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the hardware shutdown mechanism to shutdown and wake up the device
via a GPIO.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Refactor the tas2770_set_samplerate to simplify the code and access the
I2C bus only once per rate request. The ramp rate and sample rate bits
are contained in the same register so a single call to the
snd_soc_update_bits function is all that is needed
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-9-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix up the spacing for argument alignment and add new lines to separate
code. Eliminate unneccessary goto statements when the error code could
just be returned.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-8-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the unbalanced call to the pm_runtime_disable when removing the
module. pm_runtime_enable is not called nor is the pm_runtime setup in
the code. Remove the i2c_remove function and the pm_runtime_disable.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-5-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_update_bits returns a 1 when the bit was successfully updated,
returns a 0 is no update was needed and a negative if the call failed.
The code is currently failing the case of a successful update by just
checking for a non-zero number. Modify these checks and return the error
code only if there is a negative.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-7-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The devicetree binding indicates that the ti,asi-format, ti,imon-slot-no
and ti,vmon-slot-no are not required but the driver requires them or it
fails to probe. Honor the binding and allow these entries to be optional
and set the corresponding values to the default values for each as defined
in the data sheet.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the BIAS_STANDBY and BIAS_PREPARE to the set_bias_level or else the
driver will return -EINVAL which is not correct as they are valid
states.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
tas2770_reset is called during i2c probe. The reset calls the
snd_soc_component_write which depends on the tas2770->component being
available. The component pointer is not set until codec_probe so move
the reset to the codec_probe after the pointer is set.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719153822.59788-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the reset property name when allocating the GPIO descriptor.
The gpiod_get_optional appends either the -gpio or -gpios suffix to the
name.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200720181202.31000-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/873661xxhu.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a block that is indented too deeply, remove
the extraneous tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191112190218.282337-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According the documentation for snd_soc_update_bits the API
will return a 1 if the update was successful with a value change,
a 0 if the update was successful with no value change or a negative
if the command just failed.
So the value of return in the driver needs to be checked for being less
then 0 or the caller may indicate failure when the value actually
changed.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20191007171157.17813-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the unneeded and incorrect read of the TDM_CFG3 register.
The read is done but the value is never used.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20191007171157.17813-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If GPIOLIB is not set, building fails:
sound/soc/codecs/tas2770.c: In function tas2770_reset:
sound/soc/codecs/tas2770.c:38:3: error: implicit declaration of function gpiod_set_value_cansleep; did you mean gpio_set_value_cansleep? [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(tas2770->reset_gpio, 0);
^~~~~~~~~~~~~~~~~~~~~~~~
gpio_set_value_cansleep
sound/soc/codecs/tas2770.c: In function tas2770_i2c_probe:
sound/soc/codecs/tas2770.c:749:24: error: implicit declaration of function devm_gpiod_get_optional; did you mean devm_regulator_get_optional? [-Werror=implicit-function-declaration]
tas2770->reset_gpio = devm_gpiod_get_optional(tas2770->dev,
^~~~~~~~~~~~~~~~~~~~~~~
devm_regulator_get_optional
sound/soc/codecs/tas2770.c:751:13: error: GPIOD_OUT_HIGH undeclared (first use in this function); did you mean GPIOF_INIT_HIGH?
GPIOD_OUT_HIGH);
^~~~~~~~~~~~~~
GPIOF_INIT_HIGH
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191006104631.60608-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sound/soc/codecs/tas2770.c:796:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
CC: Frank Shi <shifu0704@thundersoft.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20191001175504.ufhyxh66psrht42k@332d0cec05f4
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
add tas2770 smart PA kernel driver
Signed-off-by: Frank Shi <shifu0704@thundersoft.com>
Link: https://lore.kernel.org/r/1568962709-19185-2-git-send-email-shifu0704@thundersoft.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
