| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When restarting a CPU powered by the PCA9450 power management IC, it
is beneficial to use the PCA9450 to power cycle the CPU and all its
connected peripherals to start up in a known state. The PCA9450 features
a cold start procedure initiated by an I2C command.
Add a restart handler so that the PCA9450 is used to restart the CPU.
The restart handler sends command 0x14 to the SW_RST register,
initiating a cold reset (Power recycle all regulators except LDO1, LDO2
and CLK_32K_OUT)
As the PCA9450 is a PMIC specific for the i.MX8M family CPU, the restart
handler priority is set just slightly higher than imx2_wdt and the PSCI
restart handler. This makes sure this restart handler takes precedence.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Link: https://patch.msgid.link/20250505115936.1946891-1-paul.geurts@prodrive-technologies.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the PMIC pca9452 support, which add ldo3 compared with pca9451a.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241205-pca9450-v1-4-aab448b74e78@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Adding support for new pmic pca9451a.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Link: https://msgid.link/r/20240318095633.4079027-3-joy.zou@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
L3_OUT and L4_OUT Bit fields range from Bit 0:4 and thus the
mask should be 0x1F instead of 0x0F.
Fixes: 0935ff5f1f0a ("regulator: pca9450: add pca9450 pmic driver")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20230614125240.3946519-1-t.remmet@phytec.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make the I2C Level Translator included in PCA9450 configurable from
devicetree. The reset state is off. By setting nxp,i2c-lt-enable, the
I2C Level Translator will be enabled while in STANDBY or RUN state.
Signed-off-by: Per-Daniel Olsson <perdo@axis.com>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-2-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver uses the DVS registers PCA9450_REG_BUCKxOUT_DVS0 to set the
voltage for the buck regulators 1, 2 and 3. This has no effect as the
PRESET_EN bit is set by default and therefore the preset values are used
instead, which are set to 850 mV.
To fix this we clear the PRESET_EN bit at time of initialization.
Fixes: 0935ff5f1f0a ("regulator: pca9450: add pca9450 pmic driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222115229.166620-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
By default the PCA9450 doesn't handle the assertion of the WDOG_B
signal, but this is required to guarantee that things like software
resets triggered by the watchdog work reliably.
As we don't want to rely on the bootloader to enable this, we tell
the PMIC to issue a cold reset in case the WDOG_B signal is
asserted (WDOG_B_CFG = 10), just as the NXP U-Boot code does.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-3-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add NXP pca9450 pmic driver.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/1593793178-9737-2-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
