summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/broadcom
AgeCommit message (Collapse)AuthorFilesLines
2012-07-30tg3: Fix race condition in tg3_get_stats64()Michael Chan1-2/+4
Spinlock should be taken before checking for tp->hw_stats. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-30tg3: Add New 5719 Read DMA workaroundMichael Chan2-1/+29
After Power-on-reset, the 5719's TX DMA length registers may contain uninitialized values and cause TX DMA to stall. Check for invalid values and set a register bit to flush the TX channels. The bit needs to be turned off after the DMA channels have been flushed. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-30tg3: Fix Read DMA workaround for 5719 A0.Michael Chan1-2/+1
The workaround was mis-applied to all 5719 and 5720 chips. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-30tg3: Request APE_LOCK_PHY before PHY accessMichael Chan2-0/+38
to prevent PHY access conflict with APE firmware. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-30bnx2x: remove cast around the kmalloc in bnx2x_prev_mark_pathDevendra Naga1-2/+1
casting the void pointer is redundant (Documentation/CodingStyle) Signed-off-by: Devendra Naga <develkernel412222@gmail.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2-3/+9
Pull networking updates and fixes from David Miller: 1) Reinstate the no-ref optimization for input route lookups in ipv4 to fix some routing cache removal perf regressions. 2) Make TCP socket pre-demux work on ipv6 side too, from Eric Dumazet. 3) Get RX hash value from correct place in be2net driver, from Sarveshwar Bandi. 4) Validation of FIB cached routes missing critical check, from Eric Dumazet. 5) EEH support in mlx4 driver, from Kleber Sacilotto de Souza. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits) ipv6: Early TCP socket demux ipv4: Fix input route performance regression. pch_gbe: vlan skb len fix pch_gbe: add extra clean tx pch_gbe: fix transmit watchdog timeout ixgbe: fix panic while dumping packets on Tx hang with IOMMU be2net: Fix to parse RSS hash from Receive completions correctly. net/mlx4_en: Limit the RFS filter IDs to be < RPS_NO_FILTER hyperv: Add error handling to rndis_filter_device_add() hyperv: Add a check for ring_size value ipv4: rt_cache_valid must check expired routes net/pch_gpe: Cannot disable ethernet autonegation qeth: repair crash in qeth_l3_vlan_rx_kill_vid() netiucv: cleanup attribute usage net: wiznet add missing HAS_IOMEM dependency be2net: Missing byteswap in be_get_fw_log_level causes oops on PowerPC mlx4: Add support for EEH error recovery cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN wanmain: comparing array with NULL caif: fix NULL pointer check ...
2012-07-25Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pciLinus Torvalds1-2/+2
Pull PCI changes from Bjorn Helgaas: "Host bridge hotplug: - Add MMCONFIG support for hot-added host bridges (Jiang Liu) Device hotplug: - Move fixups from __init to __devinit (Sebastian Andrzej Siewior) - Call FINAL fixups for hot-added devices, too (Myron Stowe) - Factor out generic code for P2P bridge hot-add (Yinghai Lu) - Remove all functions in a slot, not just those with _EJx (Amos Kong) Dynamic resource management: - Track bus number allocation (struct resource tree per domain) (Yinghai Lu) - Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu) - Disable decoding while updating 64-bit BARs (Bjorn Helgaas) Power management: - Add PCIe runtime D3cold support (Huang Ying) Virtualization: - Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson) - Add quirks for devices with broken INTx masking (Jan Kiszka) Miscellaneous: - Fix some PCI Express capability version issues (Myron Stowe) - Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)" * tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits) PCI: hotplug: ensure a consistent return value in error case PCI: fix undefined reference to 'pci_fixup_final_inited' PCI: build resource code for M68K architecture PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width() PCI: reorder __pci_assign_resource() (no change) PCI: fix truncation of resource size to 32 bits PCI: acpiphp: merge acpiphp_debug and debug PCI: acpiphp: remove unused res_lock sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases() PCI: call final fixups hot-added devices PCI: move final fixups from __init to __devinit x86/PCI: move final fixups from __init to __devinit MIPS/PCI: move final fixups from __init to __devinit PCI: support sizing P2P bridge I/O windows with 1K granularity PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2) PCI: disable MEM decoding while updating 64-bit MEM BARs PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too PCI: never discard enable/suspend/resume_early/resume fixups PCI: release temporary reference in __nv_msi_ht_cap_quirk() PCI: restructure 'pci_do_fixups()' ...
2012-07-25bnx2x: Correct EEE statistics gatheringYuval Mintz2-3/+9
In boards with 4-ports, Tx LPI statistics were gathered incorrectly. This patch guarantees that each pmf will only query its own port for these statistics. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-23bnx2x: Add new 57840 device IDsYuval Mintz3-10/+38
The 57840 boards come in two flavours: 2 x 20G and 4 x 10G. To better differentiate between the two flavours, a separate device ID was assigned to each. The silicon default value is still the currently supported 57840 device ID (0x168d), and since a user can damage the nvram (e.g., 'ethtool -E') the driver will still support this device ID to allow the user to amend the nvram back into a supported configuration. Notice this patch contains lines longer than 80 characters (strings). Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-22bnx2x: advertise transmit time stampingRichard Cochran1-0/+1
This driver now offers software transmit time stamping, so it should advertise that fact via ethtool. Compile tested only. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-18b44: add 64 bit statsKevin Groeneveld2-41/+58
Add support for 64 bit stats to Broadcom b44 ethernet driver. Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17bnx2x: organize BDs calculation for stop/resumeDmitry Kravkov2-4/+22
Put the numbers used for stop/resume queue in a single place and fix the condition for sanity check. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17bnx2: Try to recover from PCI block resetMichael Chan1-0/+7
If the PCI block has reset, the memory enable bit will be reset and the device will not respond to MMIO access. bnx2_reset_task() currently will not recover when this happens. Add code to detect this condition and restore the PCI state. This scenario has been reported by some users. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17tg3: Add hwmon support for temperatureMichael Chan2-0/+150
Some tg3 devices have management firmware that can export sensor data. Export temperature sensor reading via hwmon sysfs. [hwmon interface suggested by Ben Hutchings <bhutchings@solarflare.com>] Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17tg3: Add APE scratchpad read functionMatt Carlson2-2/+86
for retreiving temperature sensor data. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17tg3: Add common function tg3_ape_event_lock()Matt Carlson1-24/+32
by refactoring code in tg3_ape_send_event(). The common function will be used in subsequent patches. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17tg3: Fix the setting of the APE_HAS_NCSI flagMichael Chan1-21/+21
The driver currently skips setting this flag if the VPD contains the firmware version string. We fix this by separating the probing of NCSI from the reading of the NCSI version string. The APE_HAS_NCSI flag is needed to properly read sensor data. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-13tg3: add device id of Apple Thunderbolt Ethernet deviceGreg KH1-0/+1
The Apple Thunderbolt ethernet device is already listed in the driver, but not hooked up in the MODULE_DEVICE_TABLE(). This fixes that and allows it to work properly. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller3-6/+7
Conflicts: net/batman-adv/bridge_loop_avoidance.c net/batman-adv/bridge_loop_avoidance.h net/batman-adv/soft-interface.c net/mac80211/mlme.c With merge help from Antonio Quartulli (batman-adv) and Stephen Rothwell (drivers/net/usb/qmi_wwan.c). The net/mac80211/mlme.c conflict seemed easy enough, accounting for a conversion to some new tracing macros. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-11bnx2: Fix bug in bnx2_free_tx_skbs().Michael Chan1-3/+3
In rare cases, bnx2x_free_tx_skbs() can unmap the wrong DMA address when it gets to the last entry of the tx ring. We were not using the proper macro to skip the last entry when advancing the tx index. Reported-by: Zongyun Lai <zlai@vmware.com> Reviewed-by: Jeffrey Huang <huangjw@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-11drivers/net/ethernet: Fix non-kernel-doc comments with kernel-doc start markersBen Hutchings8-46/+21
Convert doxygen (or similar) formatted comments to kernel-doc or unformatted comment. Delete a few that are content-free. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-11drivers/net/ethernet: Fix (nearly-)kernel-doc comments for various functionsBen Hutchings1-1/+1
Fix incorrect start markers, wrapped summary lines, missing section breaks, incorrect separators, and some name mismatches. Delete a few that are content-free. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-10drivers/net/ethernet/broadcom/cnic.c: remove invalid reference to list ↵Julia Lawall1-1/+2
iterator variable If list_for_each_entry, etc complete a traversal of the list, the iterator variable ends up pointing to an address at an offset from the list head, and not a meaningful structure. Thus this value should not be used after the end of the iterator. There does not seem to be a meaningful value to provide to netdev_warn. Replace with pr_warn, since pr_err is used elsewhere. This problem was found using Coccinelle (http://coccinelle.lip6.fr/). Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-10bnx2x: populate skb->l4_rxhashEric Dumazet2-4/+16
l4_rxhash is set on skb when rxhash is obtained from canonical 4-tuple over transport ports/addresses. We can set skb->l4_rxhash for all incoming TCP packets on bnx2x for free, as cqe status contains a hash type information. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-09cnic: Don't use netdev->base_addrMichael Chan1-2/+5
commit c0357e975afdbbedab5c662d19bef865f02adc17 bnx2: stop using net_device.{base_addr, irq}. removed netdev->base_addr so we need to update cnic to get the MMIO base address from pci_resource_start(). Otherwise, mmap of the uio device will fail. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-09net: dont use __netdev_alloc_skb for bounce bufferEric Dumazet1-2/+2
commit a1c7fff7e1 (net: netdev_alloc_skb() use build_skb()) broke b44 on some 64bit machines. It appears b44 and b43 use __netdev_alloc_skb() instead of alloc_skb() for their bounce buffers. There is no need to add an extra NET_SKB_PAD reservation for bounce buffers : - In TX path, NET_SKB_PAD is useless - In RX path in b44, we force a copy of incoming frames if GFP_DMA allocations were needed. Reported-and-bisected-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-05bnx2x: set maximal number of default RSS queuesYuval Mintz1-1/+2
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-05bnx2: set maximal number of default RSS queuesYuval Mintz1-1/+1
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-05tg3: set maximal number of default RSS queuesYuval Mintz1-1/+1
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Cc: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-30cnic: Fix mmap regression.Michael Chan2-3/+9
commit 1f85d58cdf15354a7120fc9ccc9bb9c45b53af88 cnic: Remove uio mem[0]. introduced a regression as older versions of userspace app still rely on this mmap. Restore the mmap functionality and get the base address from pci_resource_start() as the nedev->base_addr has been deprecated for PCI devices. Update version to 2.5.12. Signed-off-by: Michael Chan <mchan@broadocm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28bnx2: Add missing netif_tx_disable() in bnx2_close()Michael Chan1-2/+3
to stop all tx queues. Update version to 2.2.3. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28bnx2: Add "fall through" commentsMichael Chan1-0/+4
to indicate that the mising break statements are intended. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28cnic: Handle RAMROD_CMD_ID_CLOSE error.Eddie Wai2-2/+11
If firmware returns error status, proceed to close the iSCSI connection. Update version to 2.5.11. Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28cnic: Remove uio mem[0].Michael Chan1-4/+1
This memory region is no longer used. Userspace gets the BAR address directly from sysfs. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28cnic: Read bnx2x function number from internal registerEddie Wai1-1/+7
so that it will work on any hypervisor. Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28cnic: Fix occasional NULL pointer dereference during reboot.Michael Chan1-2/+7
We register with bnx2x before we allocate ctx_tbl structure, so it is possible for bnx2x to call cnic_ctl before the structure is allocated. This can sometimes cause NULL pointer dereference of cp->ctx_tbl. We fix this by adding simple checking for valid state before proceeding. The cnic_ctl call is RCU protected so we don't have to deal with race conditions. Because of the additional checking, we need to finish the shutdown before clearing the CNIC_UP flag. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-27bnx2x: Change bnx2x_tests_str_arr to static charMerav Sicron1-1/+1
This patch changes the definition of bnx2x_tests_str_arr from char to static char. This correction will also eliminate the sparse warning created in commit cf2c1df62e065bfc15e38daf2d3479a56b320f29. Signed-off-by: Merav Sicron <meravs@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-27bnx2x, bnx2fc, bnx2i, cnic: Add statistics support and FCoE capabilities ↵Barak Witkowski6-125/+226
advertisement 1. When FCoE offload driver is registered, copy its capabilities to the chip scratchpad. 2. Copy FCoE/iSCSI MAC addresses in aligned manner to chip scratchpad. 3. Add FCoE/iSCSI statistics collection support Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-24/+30
Conflicts: drivers/net/usb/qmi_wwan.c net/batman-adv/translation-table.c net/ipv6/route.c qmi_wwan.c resolution provided by Bjørn Mork. batman-adv conflict is dealing merely with the changes of global function names to have a proper subsystem prefix. ipv6's route.c conflict is merely two side-by-side additions of network namespace methods. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: link module eepromYuval Mintz3-4/+67
Add the ethtool functionality of accessing optic modules' information and eeprom to the bnx2x driver. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: 1G sfp+ module handlingYuval Mintz3-84/+151
Automatically lower requested link speed to 1G in case 1G SFP+ module is detected. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: revised link register accessYuval Mintz3-144/+100
This is a semantic change, cleaning some sections in which the bnx2x handles the phy's registers. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: treat 0 speed as link down (copper)Yuval Mintz1-10/+12
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: link cleanupYuval Mintz1-173/+167
This patch does several things: 1. Add static to function when possible. 2. Correct comments. 3. Change msleep(small) --> usleep_range(small, small*2). Also correct existing calls to usleep_range. 4. Remove dead code. 5. Change 'if(rc != 0)' --> if(rc) Most of these changes are purely semantic. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-23bnx2x: sfp+ Tx fault detection addedYuval Mintz3-16/+99
Adds the ability to identify sfp+ modules' Tx fault, and when such occur shut down the link. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-20bnx2x: Change date and version to 1.72.51-0Merav Sicron1-2/+2
This change updates the date and version of the bnx2x driver. Signed-off-by: Merav Sicron <meravs@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-20bnx2x: Support DCBX for all functionsBarak Witkowski7-12/+31
In multi-function device, allow configuring dcbx admin params from all drivers on a single physical port. Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-20bnx2x: Add support for ethtool -LMerav Sicron5-12/+100
Add support for ethtool -L/-l for setting and getting the number of RSS queues. The 'combined' field is used as we don't support separate IRQ for Rx and Tx. Signed-off-by: Merav Sicron <meravs@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-20bnx2x: Allow up to 63 RSS queuesMerav Sicron1-10/+3
This patch removed the limitation in the code for 16 RSS queues. Signed-off-by: Merav Sicron <meravs@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-20bnx2x: Split the FP structureBarak Witkowski6-87/+155
This patch moves some fields out of the FP structure to different structures, in order to minimize size of contigiuous memory allocated. Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-04 04:17:22 +0300