| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
85x also has a similar AGPBUSY# bit as gen3. Enable it to make
sure vblank interrupts don't get dealyed during C3 state.
There's also another bit which controls whether AGPBUSY# is asserted
based on pending cacheable cycles and interrupts, or just based on
pending commands in the ring and interrupts. Select the cacheable
cycles mode since that seems to be the new way of doing things in
85x, and it does give slightly better C3 residency numbers with
glxgears running.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
My Gen3 Bspec lists the AGPBUSY# bit in INSTPM as an enable bit rather
than a disable bit. Our code has the opposite idea. Make the code match
the spec.
Might fix some gen3 C3 related interrupt delivery problems. Untested
due to lack of hardware.
v2: call it AGPBUSY_INT_EN to make it clearer it has to do with interrupts
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Apparently we need to disable VCP unit clock gating around media reset
on g4x.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Document the internal structure of the VLV display PHY a bit to help
people understand how the different register blocks relate to each
other.
v2: Add a bit more text
Make it a DOC: comment, but leave the ascii art out since
it would get mangled
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The comments in i915_reg.h aren't proper kernel-doc comments, so replace
the magic /** with just /*
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The following workarounds should be needed for pre-production hardware
only:
* WaDisablePwrmtrEvent:chv
* WaSetMaskForGfxBusyness:chv
* WaDisableGunitClockGating:chv
* WaDisableFfDopClockGating:chv
* WaDisableDopClockGating:chv
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On CHV the GMBUS port for port D is different from other gmch platforms
which have port D. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We're using the reset domains bits for g4x on ilk. But on ilk those bits
actually shifted by one bit. Fix it up so that we use the correct bits.
We were actually always writing 0x2 to the reset domain bits, which
is a reserved value. In practice it looks like the hardware ignores that
value since nothing happens if I write that value when there's a 3D
workload running. Writing the _correct_ render domain value actually
makes the GPU stop.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch adds a mmio base address variable for DSI display,
to make the DSI code generic, so that, if required, the same code
can be re-used for future platforms with different mmio base.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
These opcodes are not specific for an endpoint, but are the same for all
endpoints. So rename them accordingly, using the name the VLV2 sideband
HAS uses. Also move the macros to the .c file, since they aren't used
anywhere else.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.
v2: Add (1<<31) mask (Ville)
v3: Add Gen check for the mask (ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.
The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.
This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.
v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)
v3: Rebased on Paulo's runtime PM changes
v4: Not well validated, but rebase on
commit 730488b2eddded4497f63f70867b1256cd9e117c
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:12:32 2014 -0300
drm/i915: kill dev_priv->pm.regsave
v5: Rebased on latest code base. (Deepak)
v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)
v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Fill in the sprite bits for DDL1/DDL2 registers, and add DDL3.
Still need to write the code to use these...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Needed by the VLV S0ix context save/restore helpers.
v2:
- unchanged
v3:
- use proper GEN register prefixes (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Due to Pipe C DPINVGTT has more bits on CHV.
v2: Fix comment to say VLV/CHV (Rafael)
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
v2: Rebase on top of Ben's GT interrupt shuffling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
CHV has pipe C and PSR which cause changes to DPFLIPSTAT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
FIXME: We probably want to sprinkle _CHV suffixes over these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
These will be needed by the upcoming VLV RPM helpers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
These are additional registers needed for performance monitoring and
ARB_draw_indirect extensions in mesa.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76719
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Squash in fixup from Brad requested by Ken.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
It is now clear that this interrupt is for the primary plane and not
something global to the pipe. It also matches what the spec calls it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
GEN8 now has a qword to code for 48bit addresses.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
It seems like it wouldn't be too unlikely to be wanting to use a an
expression in the macro argument and things could go very wrong.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On Gen4+ platforms (except BDW), Render Cache Operational flush
cannot be enabled.
This WA is apparently required for all Gen4+ platforms,except BDW.
In BDW, the bit has been repurposed otherwise.
This has been tested only on vlv.
v2: Corrected the code regarding the wrong usage of
MASKED_BIT_DISABLE (Chris)
v3: Enhancing the scope of WA to Gen4+ platforms except BDW (Ville)
v4: Adding WA for g4x, crestline, broadwater (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In commit a51435a3137ad8ae75c288c39bd2d8b2696bae8f
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The framecount register was still using the old PIPE macro instead
of the new PIPE2 macro
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
For error state, like the recent modification to ACTHD, FADD also gets
an upper dword. This is useful for debug to make sure the fetch address
and head are similar.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Mesa needs to be able to write OACONTROL in order to expose the
Observability Architecture's performance counters via OpenGL.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add comment that this is just a temporary work-around and
that we need to check more things before we can allow OACONTROL writes
for real everywhere.]
[danvet 2: Squash in fixup to avoid a DRM_ERROR due to unsorted reg
list, spotted by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
PIPE_CONTROL and MI_FLUSH_DW have bits that would write to the
hardware status page. The driver stores request tracking info
there, so don't let userspace overwrite it.
v2: trailing comma fix, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Various commands that access memory have a bit to determine whether
the graphics address specified in the command should use the GGTT or
PPGTT for translation. These checks ensure that the bit indicates
PPGTT translation.
Most of these checks use the existing bit-checking infrastructure.
The PIPE_CONTROL and MI_FLUSH_DW commands, however, are multi-function
commands. The GGTT/PPGTT bit is only relevant for certain uses of the
command. As such, this change also extends the bit-checking code to
include a "condition" mask and offset. If the condition mask is non-zero
then the parser only performs the bit check when the bits specified by
the condition mask/offset are also non-zero.
NOTE: At this point in the series PPGTT must be enabled for the parser
to work correctly. If it's not enabled, userspace will not be setting
the PPGTT bits the way the parser requires. VLV is the only platform
where this is a problem, so at this point, we disable parsing for VLV.
v2: whitespace and trailing commas fixes, rebased
OTC-Tracker: AXIA-4631
Change-Id: I3f4c76b6734f1956ec47e698230f97d0998ff92b
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unecessary cast Jani spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The driver leaves most interrupts masked during normal operation,
so there would have to be additional work to enable userspace to
safely request/receive an interrupt.
v2: trailing commas, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM, and MI_LOAD_REGISTER_IMM
commands allow userspace access to registers. Only certain registers
should be allowed for such access, so enable checking for those commands.
Each ring gets its own register whitelist.
MI_LOAD_REGISTER_REG on HSW also allows register access but is currently
unused by userspace components. Leave it rejected.
PIPE_CONTROL and MEDIA_VFE_STATE allow register access based on certain
bits being set. Reject those as well.
v2: trailing commas, rebased
OTC-Tracker: AXIA-4631
Change-Id: Ie614a2f0eb2e5917de809e5a17957175d24cc44f
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
These are used to implement scanline waits in the X server.
v2: Use #defines instead of magic numbers
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
