| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Replace devm_kzalloc that has an internal multiplication with
devm_kcalloc to improve code readability and safety from overflows.
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
`sizeof(char)` evaluates to 1. Remove the churn.
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
During encryption and decryption, user requests
must be checked first, if the specifications that
are not supported by the hardware are used, the
software computing is used for processing.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The hardware only supports authentication sizes
that are 4-byte aligned. Therefore, the driver
switches to software computation in this case.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
According to the HMAC RFC, the authentication key
can be 0 bytes, and the hardware can handle this
scenario. Therefore, remove the incorrect validation
for this case.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Only the ECDH with NIST P-256 meets requirements.
The algorithm will be scheduled first for high-performance cores.
The key step is to config resv1 field of BD.
Signed-off-by: lizhi <lizhi206@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
On the HiSilicon accelerators drivers, the PF/VFs driver can send messages
to the VFs/PF by writing hardware registers, and the VFs/PF driver receives
messages from the PF/VFs by reading hardware registers. To support this
feature, a new version id is added, different communication mechanism are
used based on different version id.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the digest alg is HMAC-SHAx or another, the authsize may be less
than 4 bytes and mac_len of the BD is set to zero, the hardware considers
it a BD configuration error and reports a ras error, so the sec driver
needs to switch to software calculation in this case, this patch add a
check for it and remove unnecessary check that has been done by crypto.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the AEAD algorithm is used for encryption or decryption,
the input authentication length varies, the hardware needs to
obtain the input length to pass the integrity check verification.
Currently, the driver uses a fixed authentication length,which
causes decryption failure, so the length configuration is modified.
In addition, the step of setting the auth length is unnecessary,
so it was deleted from the setkey function.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The error detection of the data aggregation feature is separated from
the compression/decompression feature. This patch enables the error
detection and reporting of the data aggregation feature. When an
unrecoverable error occurs in the algorithm core, the device reports
the error to the driver, and the driver will reset the device.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The zip device adds data aggregation feature, data with the
same key can be combined.
This patch enables the device data aggregation feature.
New feature is called "hashagg" name and registered to
the uacce subsystem to allow applications to submit data
aggregation operations in user space.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Offset based on (id * size) is wrong for sqc and cqc.
(*sqc/*cqc + 1) can already offset sizeof(struct(Xqc)) length.
Fixes: 15f112f9cef5 ("crypto: hisilicon/debugfs - mask the unnecessary info from the dump")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If an error indicating that the device needs to be reset is reported,
disable the error reporting before device reset is complete,
enable the error reporting after the reset is complete to prevent
the same error from being reported repeatedly.
Fixes: eaebf4c3b103 ("crypto: hisilicon - Unify hardware error init/uninit into QM")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Query the capability register status of accelerator devices
(SEC, HPRE and ZIP) through the debugfs interface, for example:
cat cap_regs. The purpose is to improve the robustness and
locability of hardware devices and drivers.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/crypto to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Ensure that the inline function contains no more than 10 lines.
move q_num_set() from hisi_acc_qm.h to qm.c.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently, the driver enables clock gating for only one cluster.
However, the new hardware has three clusters. Therefore, clock
gating needs to be enabled based on the number of clusters on the
current hardware.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The drivers aspeed-acry.c, hpre_crypto.c and jh7110-rsa.c purport to
implement sign/verify operations for raw (unpadded) "rsa".
But there is no such thing as message digests generally need to be
padded according to a predefined scheme (such as PSS or PKCS#1) to
match the size of the usually much larger RSA keys.
The bogus sign/verify operations defined by these drivers are never
called but block removal of sign/verify from akcipher_alg. Drop them.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is a extraneous space after a newline in a dev_err message.
Remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The master ooo cannot be completely closed when the
accelerator core reports memory error. Therefore, the driver
needs to inject the qm error to close the master ooo. Currently,
the qm error is injected after stopping queue, memory may be
released immediately after stopping queue, causing the device to
access the released memory. Therefore, error is injected to close master
ooo before stopping queue to ensure that the device does not access
the released memory.
Fixes: 6c6dd5802c2d ("crypto: hisilicon/qm - add controller reset interface")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The timeout threshold of the hpre cluster is 16ms. When the CPU
and device share virtual address, page fault processing time may
exceed the threshold.
In the current test, there is a high probability that the
cluster times out. However, the cluster is waiting for the
completion of memory access, which is not an error, the device
does not need to be reset. If an error occurs in the cluster,
qm also reports the error. Therefore, the cluster timeout
error of hpre can be masked.
Fixes: d90fab0deb8e ("crypto: hisilicon/qm - get error type from hardware registers")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Before the device is enabled again, the device may still
store the previously processed data. If an error occurs in
the previous task, the device may fail to be enabled again.
Therefore, before enabling device, reset the device to restore
the initial state.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Header files is included Order-ref: standard library headers,
OS library headers, and project-specific headers. This patch
modifies the order of header files according to suggestions.
In addition, use %u to print unsigned int variables to prevent
overflow.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Apply for a lock before the qp send operation to ensure no
resource race in multi-concurrency situations.
This modification has almost no impact on performance.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If an error occurs in the process after the SGL is mapped
successfully, it need to unmap the SGL.
Otherwise, memory problems may occur.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The req_lock is currently implemented as a rw_lock, but there are no
instances where read_lock() is called. This means that the lock is
effectively only used by writers, making it functionally equivalent to
a simple spinlock.
As stated in Documentation/locking/spinlocks.rst:
"Reader-writer locks require more atomic memory operations than simple
spinlocks. Unless the reader critical section is long, you are better
off just using spinlocks."
Since the rw_lock in this case incurs additional atomic memory
operations without any benefit from reader-writer locking, it is more
efficient to replace it with a spinlock. This patch implements that
replacement to optimize the driver's performance.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently, the reg is queried based on the fixed address offset
array. When the number of accelerator cores changes, the system
can not flexibly respond to the change.
Therefore, the reg to be queried is calculated based on the
comp or decomp core base address.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
enable and disable
When the vf is enabled, the value of vfs_num must be assigned
after the VF configuration is complete. Otherwise, the device
may be accessed before the virtual configuration is complete,
causing an error.
When the vf is disabled, clear vfs_num and execute
qm_pm_put_sync before hisi_qm_sriov_disable is return.
Otherwise, if qm_clear_vft_config fails, users may access the
device when the PCI virtualization is disabled, resulting in an
error.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The offset of SEC_CORE_ENABLE_BITMAP should be 0 instead of 32,
it cause a kasan shift-out-bounds warning, fix it.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Some information showed by the dump function is invalid. Mask
the unnecessary information from the dump file.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the qm uninit command is executed, the err data needs to
be released to prevent memory leakage. The error information
release operation and uacce_remove are integrated in
qm_remove_uacce.
So add the qm_remove_uacce to qm uninit to avoid err memory
leakage.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
space in sq dump
When dumping SQ, only the corresponding ID's SQE needs to be
dumped, and there is no need to apply for the entire SQE
memory. This is because excessive dump operations can lead to
memory resource waste.
Therefor apply for the space corresponding to sqe_id separately
to avoid space waste.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The AIV is one of the SEC resources. When releasing resources,
it need to release the AIV resources at the same time.
Otherwise, memory leakage occurs.
The aiv resource release is added to the sec resource release
function.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is a scenario where the file directory is created but the
file memory is not set. In this case, if a user accesses the
file, an error occurs.
So during the creation process of debugfs, memory should be
allocated first before creating the directory. In the release
process, the directory should be deleted first before releasing
the memory to avoid the situation where the memory does not
exist when accessing the directory.
In addition, the directory released by the debugfs is a global
variable. When the debugfs of an accelerator fails to be
initialized, releasing the directory of the global variable
affects the debugfs initialization of other accelerators.
The debugfs root directory released by debugfs init should be a
member of qm, not a global variable.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The cmd type can be extended. Currently, only four types of cmd
can be processed. Therefor, add the default processing branch
to intercept incorrect parameter input.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
creation
There is a scenario where the file directory is created but the
file attribute is not set. In this case, if a user accesses the
file, an error occurs.
So adjust the processing logic in the debugfs creation to
prevent the file from being accessed before the file attributes
such as the index are set.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The input parameter check in acc_get_sgl is redundant. The
caller has been verified once. When the check is performed for
multiple times, the performance deteriorates.
So the redundant parameter verification is deleted, and the
index verification is changed to the module entry function for
verification.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
During the zip probe process, the debugfs failure does not stop
the probe. When debugfs initialization fails, jumping to the
error branch will also release regs, in addition to its own
rollback operation.
As a result, it may be released repeatedly during the regs
uninit process. Therefore, the null check needs to be added to
the regs uninit process.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When CONFIG_PCI_IOV is disabled, the SRIOV configuration
function is not required. An error occurs if this function is
incorrectly called.
Consistent with other modules, add the condition for
configuring the sriov function of sec_pci_driver.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add the missing CRYPTO_ALG_ASYNC flag since hisilizon zip driver
works asynchronously.
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Acked-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The function qm_stop_qp_nolock() always return zero, so
function type is changed to void.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The debugfs files 'dev_state' and 'dev_timeout' are added.
Users can query the current queue stop status through these two
files. And set the waiting timeout when the queue is released.
dev_state: if dev_timeout is set, dev_state indicates the status
of stopping the queue. 0 indicates that the queue is stopped
successfully. Other values indicate that the queue stops fail.
If dev_timeout is not set, the value of dev_state is 0;
dev_timeout: if the queue fails to stop, the queue is released
after waiting dev_timeout * 20ms.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Hardware V3 could be able to drain function by sending mailbox
to hardware which will trigger tasks in device to be flushed out.
When the function is reset, the function can be stopped by this way.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Unused parameter of static functions should be removed.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch fixes following cleanup issues:
- The return value of the function is
inconsistent with the actual return type.
- After the pointer type is directly converted
to the `__le64` type, the program may crash
or produce unexpected results.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Nested macros are integrated into a single macro,
making the code simpler.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
As the sec DFX function is enhanced, some RAS registers are added
to the original DFX registers to enhance the DFX positioning function.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Switch to raw_smp_processor_id() to prevent a number of
warnings from kernel debugging. We do not care about
preemption here, as the CPU number is only used as a
poor mans load balancing or device selection. If preemption
happens during an encrypt/decrypt operation a small performance
hit will occur but everything will continue to work, so just
ignore it. This commit is similar to e7a9b05ca4
("crypto: cavium - Fix smp_processor_id() warnings").
[ 7538.874350] BUG: using smp_processor_id() in preemptible [00000000] code: af_alg06/8438
[ 7538.874368] caller is debug_smp_processor_id+0x1c/0x28
[ 7538.874373] CPU: 50 PID: 8438 Comm: af_alg06 Kdump: loaded Not tainted 5.10.0.pc+ #18
[ 7538.874377] Call trace:
[ 7538.874387] dump_backtrace+0x0/0x210
[ 7538.874389] show_stack+0x2c/0x38
[ 7538.874392] dump_stack+0x110/0x164
[ 7538.874394] check_preemption_disabled+0xf4/0x108
[ 7538.874396] debug_smp_processor_id+0x1c/0x28
[ 7538.874406] sec_create_qps+0x24/0xe8 [hisi_sec2]
[ 7538.874408] sec_ctx_base_init+0x20/0x4d8 [hisi_sec2]
[ 7538.874411] sec_aead_ctx_init+0x68/0x180 [hisi_sec2]
[ 7538.874413] sec_aead_sha256_ctx_init+0x28/0x38 [hisi_sec2]
[ 7538.874421] crypto_aead_init_tfm+0x54/0x68
[ 7538.874423] crypto_create_tfm_node+0x6c/0x110
[ 7538.874424] crypto_alloc_tfm_node+0x74/0x288
[ 7538.874426] crypto_alloc_aead+0x40/0x50
[ 7538.874431] aead_bind+0x50/0xd0
[ 7538.874433] alg_bind+0x94/0x148
[ 7538.874439] __sys_bind+0x98/0x118
[ 7538.874441] __arm64_sys_bind+0x28/0x38
[ 7538.874445] do_el0_svc+0x88/0x258
[ 7538.874447] el0_svc+0x1c/0x28
[ 7538.874449] el0_sync_handler+0x8c/0xb8
[ 7538.874452] el0_sync+0x148/0x180
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Read the values of some device registers before the device
is reset, these values help analyze the cause of the device exception.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Support get device current state. The value 0 indicates that
the device is busy, and the value 1 indicates that the
device is idle. When the device is in suspended, 1 is returned.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
