diff options
Diffstat (limited to 'drivers/tty/serial')
28 files changed, 159 insertions, 1075 deletions
diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c index 70d7826788f5..c171ce6db691 100644 --- a/drivers/tty/serial/8250/8250_early.c +++ b/drivers/tty/serial/8250/8250_early.c @@ -204,9 +204,6 @@ OF_EARLYCON_DECLARE(omap8250, "ti,omap4-uart", early_omap8250_setup); #ifdef CONFIG_SERIAL_8250_RT288X -unsigned int au_serial_in(struct uart_port *p, int offset); -void au_serial_out(struct uart_port *p, int offset, int value); - static int __init early_au_setup(struct earlycon_device *dev, const char *opt) { dev->port.serial_in = au_serial_in; diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index fa876e2c13e5..f7d3023f860f 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -572,15 +572,22 @@ static int mtk8250_probe(struct platform_device *pdev) pm_runtime_enable(&pdev->dev); err = mtk8250_runtime_resume(&pdev->dev); if (err) - return err; + goto err_pm_disable; data->line = serial8250_register_8250_port(&uart); - if (data->line < 0) - return data->line; + if (data->line < 0) { + err = data->line; + goto err_pm_disable; + } data->rx_wakeup_irq = platform_get_irq_optional(pdev, 1); return 0; + +err_pm_disable: + pm_runtime_disable(&pdev->dev); + + return err; } static int mtk8250_remove(struct platform_device *pdev) diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index 562087df7d33..23e0decde33e 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -27,6 +27,7 @@ #include <linux/pm_qos.h> #include <linux/pm_wakeirq.h> #include <linux/dma-mapping.h> +#include <linux/sys_soc.h> #include "8250.h" @@ -41,6 +42,7 @@ */ #define UART_ERRATA_CLOCK_DISABLE (1 << 3) #define UART_HAS_EFR2 BIT(4) +#define UART_HAS_RHR_IT_DIS BIT(5) #define OMAP_UART_FCR_RX_TRIG 6 #define OMAP_UART_FCR_TX_TRIG 4 @@ -94,6 +96,10 @@ #define OMAP_UART_REV_52 0x0502 #define OMAP_UART_REV_63 0x0603 +/* Interrupt Enable Register 2 */ +#define UART_OMAP_IER2 0x1B +#define UART_OMAP_IER2_RHR_IT_DIS BIT(2) + /* Enhanced features register 2 */ #define UART_OMAP_EFR2 0x23 #define UART_OMAP_EFR2_TIMEOUT_BEHAVE BIT(6) @@ -184,11 +190,6 @@ static void omap_8250_mdr1_errataset(struct uart_8250_port *up, struct omap8250_priv *priv) { u8 timeout = 255; - u8 old_mdr1; - - old_mdr1 = serial_in(up, UART_OMAP_MDR1); - if (old_mdr1 == priv->mdr1) - return; serial_out(up, UART_OMAP_MDR1, priv->mdr1); udelay(2); @@ -533,6 +534,11 @@ static void omap_8250_pm(struct uart_port *port, unsigned int state, static void omap_serial_fill_features_erratas(struct uart_8250_port *up, struct omap8250_priv *priv) { + const struct soc_device_attribute k3_soc_devices[] = { + { .family = "AM65X", }, + { .family = "J721E", .revision = "SR1.0" }, + { /* sentinel */ } + }; u32 mvr, scheme; u16 revision, major, minor; @@ -580,6 +586,14 @@ static void omap_serial_fill_features_erratas(struct uart_8250_port *up, default: break; } + + /* + * AM65x SR1.0, AM65x SR2.0 and J721e SR1.0 don't + * don't have RHR_IT_DIS bit in IER2 register. So drop to flag + * to enable errata workaround. + */ + if (soc_device_match(k3_soc_devices)) + priv->habit &= ~UART_HAS_RHR_IT_DIS; } static void omap8250_uart_qos_work(struct work_struct *work) @@ -761,17 +775,27 @@ static void __dma_rx_do_complete(struct uart_8250_port *p) { struct uart_8250_dma *dma = p->dma; struct tty_port *tty_port = &p->port.state->port; + struct omap8250_priv *priv = p->port.private_data; struct dma_chan *rxchan = dma->rxchan; dma_cookie_t cookie; struct dma_tx_state state; int count; int ret; + u32 reg; if (!dma->rx_running) goto out; cookie = dma->rx_cookie; dma->rx_running = 0; + + /* Re-enable RX FIFO interrupt now that transfer is complete */ + if (priv->habit & UART_HAS_RHR_IT_DIS) { + reg = serial_in(p, UART_OMAP_IER2); + reg &= ~UART_OMAP_IER2_RHR_IT_DIS; + serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS); + } + dmaengine_tx_status(rxchan, cookie, &state); count = dma->rx_size - state.residue + state.in_flight_bytes; @@ -867,6 +891,7 @@ static int omap_8250_rx_dma(struct uart_8250_port *p) int err = 0; struct dma_async_tx_descriptor *desc; unsigned long flags; + u32 reg; if (priv->rx_dma_broken) return -EINVAL; @@ -902,6 +927,17 @@ static int omap_8250_rx_dma(struct uart_8250_port *p) dma->rx_cookie = dmaengine_submit(desc); + /* + * Disable RX FIFO interrupt while RX DMA is enabled, else + * spurious interrupt may be raised when data is in the RX FIFO + * but is yet to be drained by DMA. + */ + if (priv->habit & UART_HAS_RHR_IT_DIS) { + reg = serial_in(p, UART_OMAP_IER2); + reg |= UART_OMAP_IER2_RHR_IT_DIS; + serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS); + } + dma_async_issue_pending(dma->rxchan); out: spin_unlock_irqrestore(&priv->rx_dma_lock, flags); @@ -1182,7 +1218,7 @@ static struct omap8250_dma_params am33xx_dma = { static struct omap8250_platdata am654_platdata = { .dma_params = &am654_dma, - .habit = UART_HAS_EFR2, + .habit = UART_HAS_EFR2 | UART_HAS_RHR_IT_DIS, }; static struct omap8250_platdata am33xx_platdata = { diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index d5a513efb261..689d8227f95f 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -1964,7 +1964,7 @@ pci_moxa_setup(struct serial_private *priv, * This list is ordered alphabetically by vendor then device. * Specific entries must come before more generic entries. */ -static struct pci_serial_quirk pci_serial_quirks[] __refdata = { +static struct pci_serial_quirk pci_serial_quirks[] = { /* * ADDI-DATA GmbH communication cards <info@addi-data.com> */ diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c index e3d10794dbba..35ff6627c61b 100644 --- a/drivers/tty/serial/8250/serial_cs.c +++ b/drivers/tty/serial/8250/serial_cs.c @@ -559,16 +559,13 @@ static int multi_config(struct pcmcia_device *link) */ if (info->manfid == MANFID_OXSEMI || (info->manfid == MANFID_POSSIO && info->prodid == PRODID_POSSIO_GCC)) { - int err; - if (link->config_index == 1 || link->config_index == 3) { - err = setup_serial(link, info, base2, - link->irq); + setup_serial(link, info, base2, link->irq); base2 = link->resource[0]->start; } else { - err = setup_serial(link, info, link->resource[0]->start, - link->irq); + setup_serial(link, info, link->resource[0]->start, + link->irq); } info->c950ctrl = base2; diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 28f22e58639c..12d71d5eb6ca 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -206,7 +206,7 @@ config SERIAL_MESON config SERIAL_MESON_CONSOLE bool "Support for console on meson" - depends on SERIAL_MESON=y + depends on SERIAL_MESON select SERIAL_CORE_CONSOLE select SERIAL_EARLYCON help @@ -704,22 +704,6 @@ config SERIAL_SH_SCI_DMA depends on SERIAL_SH_SCI && DMA_ENGINE default ARCH_RENESAS -config SERIAL_PNX8XXX - bool "Enable PNX8XXX SoCs' UART Support" - depends on SOC_PNX833X - select SERIAL_CORE - help - If you have a MIPS-based Philips SoC such as PNX8330 and you want - to use serial ports, say Y. Otherwise, say N. - -config SERIAL_PNX8XXX_CONSOLE - bool "Enable PNX8XX0 serial console" - depends on SERIAL_PNX8XXX - select SERIAL_CORE_CONSOLE - help - If you have a MIPS-based Philips SoC such as PNX8330 and you want - to use serial console, say Y. Otherwise, say N. - config SERIAL_HS_LPC32XX tristate "LPC32XX high speed serial port support" depends on ARCH_LPC32XX || COMPILE_TEST @@ -1133,7 +1117,7 @@ config SERIAL_TIMBERDALE config SERIAL_BCM63XX tristate "Broadcom BCM63xx/BCM33xx UART support" select SERIAL_CORE - depends on MIPS || ARM || COMPILE_TEST + depends on COMMON_CLK help This enables the driver for the onchip UART core found on the following chipsets: diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index caf167f0c10a..af44b231123c 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -27,7 +27,6 @@ obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o obj-$(CONFIG_SERIAL_PXA_NON8250) += pxa.o -obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o obj-$(CONFIG_SERIAL_SA1100) += sa1100.o obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o obj-$(CONFIG_SERIAL_SAMSUNG) += samsung_tty.o diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 87dc3fc15694..c255476cce28 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -2789,7 +2789,7 @@ static const struct of_device_id sbsa_uart_of_match[] = { }; MODULE_DEVICE_TABLE(of, sbsa_uart_of_match); -static const struct acpi_device_id sbsa_uart_acpi_match[] = { +static const struct acpi_device_id __maybe_unused sbsa_uart_acpi_match[] = { { "ARMH0011", 0 }, {}, }; diff --git a/drivers/tty/serial/earlycon.c b/drivers/tty/serial/earlycon.c index b70877932d47..57c70851f22a 100644 --- a/drivers/tty/serial/earlycon.c +++ b/drivers/tty/serial/earlycon.c @@ -175,7 +175,7 @@ static int __init register_earlycon(char *buf, const struct earlycon_id *match) */ int __init setup_earlycon(char *buf) { - const struct earlycon_id **p_match; + const struct earlycon_id *match; bool empty_compatible = true; if (!buf || !buf[0]) @@ -185,9 +185,7 @@ int __init setup_earlycon(char *buf) return -EALREADY; again: - for (p_match = __earlycon_table; p_match < __earlycon_table_end; - p_match++) { - const struct earlycon_id *match = *p_match; + for (match = __earlycon_table; match < __earlycon_table_end; match++) { size_t len = strlen(match->name); if (strncmp(buf, match->name, len)) diff --git a/drivers/tty/serial/fsl_linflexuart.c b/drivers/tty/serial/fsl_linflexuart.c index 3e28be402aef..d87048073abe 100644 --- a/drivers/tty/serial/fsl_linflexuart.c +++ b/drivers/tty/serial/fsl_linflexuart.c @@ -252,23 +252,22 @@ static irqreturn_t linflex_rxint(int irq, void *dev_id) flg = TTY_NORMAL; sport->icount.rx++; - if (status & (LINFLEXD_UARTSR_BOF | LINFLEXD_UARTSR_SZF | - LINFLEXD_UARTSR_FEF | LINFLEXD_UARTSR_PE)) { - if (status & LINFLEXD_UARTSR_SZF) - status |= LINFLEXD_UARTSR_SZF; + if (status & (LINFLEXD_UARTSR_BOF | LINFLEXD_UARTSR_FEF | + LINFLEXD_UARTSR_PE)) { if (status & LINFLEXD_UARTSR_BOF) - status |= LINFLEXD_UARTSR_BOF; + sport->icount.overrun++; if (status & LINFLEXD_UARTSR_FEF) { - if (!rx) + if (!rx) { brk = true; - status |= LINFLEXD_UARTSR_FEF; + sport->icount.brk++; + } else + sport->icount.frame++; } if (status & LINFLEXD_UARTSR_PE) - status |= LINFLEXD_UARTSR_PE; + sport->icount.parity++; } - writel(status | LINFLEXD_UARTSR_RMB | LINFLEXD_UARTSR_DRFRFE, - sport->membase + UARTSR); + writel(status, sport->membase + UARTSR); status = readl(sport->membase + UARTSR); if (brk) { diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c index 21d519c804cb..182e0ccd60b2 100644 --- a/drivers/tty/serial/ifx6x60.c +++ b/drivers/tty/serial/ifx6x60.c @@ -545,6 +545,7 @@ static void ifx_spi_hangup(struct tty_struct *tty) /** * ifx_port_activate * @port: our tty port + * @tty: our tty device * * tty port activate method - called for first open. Serialized * with hangup and shutdown by the tty layer. @@ -719,7 +720,7 @@ complete_exit: /** * ifx_spio_io - I/O tasklet - * @data: our SPI device + * @t: tasklet construct used to fetch the SPI device * * Queue data for transmission if possible and then kick off the * transfer. diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index cacf7266a262..425624d794dd 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -30,7 +30,6 @@ #include <linux/dma-mapping.h> #include <asm/irq.h> -#include <linux/platform_data/serial-imx.h> #include <linux/platform_data/dma-imx.h> #include "serial_mctrl_gpio.h" @@ -263,25 +262,6 @@ static struct imx_uart_data imx_uart_devdata[] = { }, }; -static const struct platform_device_id imx_uart_devtype[] = { - { - .name = "imx1-uart", - .driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX1_UART], - }, { - .name = "imx21-uart", - .driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX21_UART], - }, { - .name = "imx53-uart", - .driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX53_UART], - }, { - .name = "imx6q-uart", - .driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX6Q_UART], - }, { - /* sentinel */ - } -}; -MODULE_DEVICE_TABLE(platform, imx_uart_devtype); - static const struct of_device_id imx_uart_dt_ids[] = { { .compatible = "fsl,imx6q-uart", .data = &imx_uart_devdata[IMX6Q_UART], }, { .compatible = "fsl,imx53-uart", .data = &imx_uart_devdata[IMX53_UART], }, @@ -1881,7 +1861,7 @@ static int imx_uart_poll_init(struct uart_port *port) ucr1 |= UCR1_UARTEN; ucr1 &= ~(UCR1_TRDYEN | UCR1_RTSDEN | UCR1_RRDYEN); - ucr2 |= UCR2_RXEN; + ucr2 |= UCR2_RXEN | UCR2_TXEN; ucr2 &= ~UCR2_ATEN; imx_uart_writel(sport, ucr1, UCR1); @@ -2183,70 +2163,6 @@ static struct uart_driver imx_uart_uart_driver = { .cons = IMX_CONSOLE, }; -#ifdef CONFIG_OF -/* - * This function returns 1 iff pdev isn't a device instatiated by dt, 0 iff it - * could successfully get all information from dt or a negative errno. - */ -static int imx_uart_probe_dt(struct imx_port *sport, - struct platform_device *pdev) -{ - struct device_node *np = pdev->dev.of_node; - int ret; - - sport->devdata = of_device_get_match_data(&pdev->dev); - if (!sport->devdata) - /* no device tree device */ - return 1; - - ret = of_alias_get_id(np, "serial"); - if (ret < 0) { - dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret); - return ret; - } - sport->port.line = ret; - - if (of_get_property(np, "uart-has-rtscts", NULL) || - of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */) - sport->have_rtscts = 1; - - if (of_get_property(np, "fsl,dte-mode", NULL)) - sport->dte_mode = 1; - - if (of_get_property(np, "rts-gpios", NULL)) - sport->have_rtsgpio = 1; - - if (of_get_property(np, "fsl,inverted-tx", NULL)) - sport->inverted_tx = 1; - - if (of_get_property(np, "fsl,inverted-rx", NULL)) - sport->inverted_rx = 1; - - return 0; -} -#else -static inline int imx_uart_probe_dt(struct imx_port *sport, - struct platform_device *pdev) -{ - return 1; -} -#endif - -static void imx_uart_probe_pdata(struct imx_port *sport, - struct platform_device *pdev) -{ - struct imxuart_platform_data *pdata = dev_get_platdata(&pdev->dev); - - sport->port.line = pdev->id; - sport->devdata = (struct imx_uart_data *) pdev->id_entry->driver_data; - - if (!pdata) - return; - - if (pdata->flags & IMXUART_HAVE_RTSCTS) - sport->have_rtscts = 1; -} - static enum hrtimer_restart imx_trigger_start_tx(struct hrtimer *t) { struct imx_port *sport = container_of(t, struct imx_port, trigger_start_tx); @@ -2275,6 +2191,7 @@ static enum hrtimer_restart imx_trigger_stop_tx(struct hrtimer *t) static int imx_uart_probe(struct platform_device *pdev) { + struct device_node *np = pdev->dev.of_node; struct imx_port *sport; void __iomem *base; int ret = 0; @@ -2286,11 +2203,30 @@ static int imx_uart_probe(struct platform_device *pdev) if (!sport) return -ENOMEM; - ret = imx_uart_probe_dt(sport, pdev); - if (ret > 0) - imx_uart_probe_pdata(sport, pdev); - else if (ret < 0) + sport->devdata = of_device_get_match_data(&pdev->dev); + + ret = of_alias_get_id(np, "serial"); + if (ret < 0) { + dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret); return ret; + } + sport->port.line = ret; + + if (of_get_property(np, "uart-has-rtscts", NULL) || + of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */) + sport->have_rtscts = 1; + + if (of_get_property(np, "fsl,dte-mode", NULL)) + sport->dte_mode = 1; + + if (of_get_property(np, "rts-gpios", NULL)) + sport->have_rtsgpio = 1; + + if (of_get_property(np, "fsl,inverted-tx", NULL)) + sport->inverted_tx = 1; + + if (of_get_property(np, "fsl,inverted-rx", NULL)) + sport->inverted_rx = 1; if (sport->port.line >= ARRAY_SIZE(imx_uart_ports)) { dev_err(&pdev->dev, "serial%d out of range\n", @@ -2639,7 +2575,6 @@ static struct platform_driver imx_uart_platform_driver = { .probe = imx_uart_probe, .remove = imx_uart_remove, - .id_table = imx_uart_devtype, .driver = { .name = "imx-uart", .of_match_table = imx_uart_dt_ids, diff --git a/drivers/tty/serial/jsm/jsm_cls.c b/drivers/tty/serial/jsm/jsm_cls.c index c061a7b7bd23..b507a2cec926 100644 --- a/drivers/tty/serial/jsm/jsm_cls.c +++ b/drivers/tty/serial/jsm/jsm_cls.c @@ -397,10 +397,8 @@ static void cls_copy_data_from_uart_to_queue(struct jsm_channel *ch) * which in this case is the break signal. */ if (linestatus & error_mask) { - u8 discard; - linestatus = 0; - discard = readb(&ch->ch_cls_uart->txrx); + readb(&ch->ch_cls_uart->txrx); continue; } diff --git a/drivers/tty/serial/jsm/jsm_tty.c b/drivers/tty/serial/jsm/jsm_tty.c index 689774c073ca..512b77195e9f 100644 --- a/drivers/tty/serial/jsm/jsm_tty.c +++ b/drivers/tty/serial/jsm/jsm_tty.c @@ -607,7 +607,7 @@ void jsm_input(struct jsm_channel *ch) * Give the Linux ld the flags in the * format it likes. */ - if (*(ch->ch_equeue +tail +i) & UART_LSR_BI) + if (*(ch->ch_equeue + tail + i) & UART_LSR_BI) tty_insert_flip_char(port, *(ch->ch_rqueue +tail +i), TTY_BREAK); else if (*(ch->ch_equeue +tail +i) & UART_LSR_PE) tty_insert_flip_char(port, *(ch->ch_rqueue +tail +i), TTY_PARITY); diff --git a/drivers/tty/serial/lpc32xx_hs.c b/drivers/tty/serial/lpc32xx_hs.c index b5898c932036..1fa098d7aec4 100644 --- a/drivers/tty/serial/lpc32xx_hs.c +++ b/drivers/tty/serial/lpc32xx_hs.c @@ -241,12 +241,11 @@ static unsigned int __serial_get_clock_div(unsigned long uartclk, static void __serial_uart_flush(struct uart_port *port) { - u32 tmp; int cnt = 0; while ((readl(LPC32XX_HSUART_LEVEL(port->membase)) > 0) && (cnt++ < FIFO_READ_LIMIT)) - tmp = readl(LPC32XX_HSUART_FIFO(port->membase)); + readl(LPC32XX_HSUART_FIFO(port->membase)); } static void __serial_lpc32xx_rx(struct uart_port *port) diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c index 21130af106bb..9795b2e8b0b2 100644 --- a/drivers/tty/serial/max310x.c +++ b/drivers/tty/serial/max310x.c @@ -15,8 +15,8 @@ #include <linux/device.h> #include <linux/gpio/driver.h> #include <linux/module.h> -#include <linux/of.h> -#include <linux/of_device.h> +#include <linux/mod_devicetable.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/serial_core.h> #include <linux/serial.h> @@ -267,7 +267,7 @@ struct max310x_one { container_of(_port, struct max310x_one, port) struct max310x_port { - struct max310x_devtype *devtype; + const struct max310x_devtype *devtype; struct regmap *regmap; struct clk *clk; #ifdef CONFIG_GPIOLIB @@ -1269,11 +1269,10 @@ static int max310x_gpio_set_config(struct gpio_chip *chip, unsigned int offset, } #endif -static int max310x_probe(struct device *dev, struct max310x_devtype *devtype, +static int max310x_probe(struct device *dev, const struct max310x_devtype *devtype, struct regmap *regmap, int irq) { int i, ret, fmin, fmax, freq, uartclk; - struct clk *clk_osc, *clk_xtal; struct max310x_port *s; bool xtal = false; @@ -1287,23 +1286,24 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype, return -ENOMEM; } - clk_osc = devm_clk_get(dev, "osc"); - clk_xtal = devm_clk_get(dev, "xtal"); - if (!IS_ERR(clk_osc)) { - s->clk = clk_osc; + s->clk = devm_clk_get_optional(dev, "osc"); + if (IS_ERR(s->clk)) + return PTR_ERR(s->clk); + if (s->clk) { fmin = 500000; fmax = 35000000; - } else if (!IS_ERR(clk_xtal)) { - s->clk = clk_xtal; - fmin = 1000000; - fmax = 4000000; - xtal = true; - } else if (PTR_ERR(clk_osc) == -EPROBE_DEFER || - PTR_ERR(clk_xtal) == -EPROBE_DEFER) { - return -EPROBE_DEFER; } else { - dev_err(dev, "Cannot get clock\n"); - return -EINVAL; + s->clk = devm_clk_get_optional(dev, "xtal"); + if (IS_ERR(s->clk)) + return PTR_ERR(s->clk); + if (s->clk) { + fmin = 1000000; + fmax = 4000000; + xtal = true; + } else { + dev_err(dev, "Cannot get clock\n"); + return -EINVAL; + } } ret = clk_prepare_enable(s->clk); @@ -1478,7 +1478,7 @@ static struct regmap_config regcfg = { #ifdef CONFIG_SPI_MASTER static int max310x_spi_probe(struct spi_device *spi) { - struct max310x_devtype *devtype; + const struct max310x_devtype *devtype; struct regmap *regmap; int ret; @@ -1490,18 +1490,9 @@ static int max310x_spi_probe(struct spi_device *spi) if (ret) return ret; - if (spi->dev.of_node) { - const struct of_device_id *of_id = - of_match_device(max310x_dt_ids, &spi->dev); - if (!of_id) - return -ENODEV; - - devtype = (struct max310x_devtype *)of_id->data; - } else { - const struct spi_device_id *id_entry = spi_get_device_id(spi); - - devtype = (struct max310x_devtype *)id_entry->driver_data; - } + devtype = device_get_match_data(&spi->dev); + if (!devtype) + devtype = (struct max310x_devtype *)spi_get_device_id(spi)->driver_data; regcfg.max_register = devtype->nr * 0x20 - 1; regmap = devm_regmap_init_spi(spi, ®cfg); @@ -1526,7 +1517,7 @@ MODULE_DEVICE_TABLE(spi, max310x_id_table); static struct spi_driver max310x_spi_driver = { .driver = { .name = MAX310X_NAME, - .of_match_table = of_match_ptr(max310x_dt_ids), + .of_match_table = max310x_dt_ids, .pm = &max310x_pm_ops, }, .probe = max310x_spi_probe, diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c index d2c08b760f83..69eeef9edfa5 100644 --- a/drivers/tty/serial/meson_uart.c +++ b/drivers/tty/serial/meson_uart.c @@ -604,7 +604,6 @@ static int __init meson_serial_console_init(void) register_console(&meson_serial_console); return 0; } -console_initcall(meson_serial_console_init); static void meson_serial_early_console_write(struct console *co, const char *s, @@ -634,6 +633,9 @@ OF_EARLYCON_DECLARE(meson, "amlogic,meson-ao-uart", #define MESON_SERIAL_CONSOLE (&meson_serial_console) #else +static int __init meson_serial_console_init(void) { + return 0; +} #define MESON_SERIAL_CONSOLE NULL #endif @@ -824,6 +826,10 @@ static int __init meson_uart_init(void) { int ret; + ret = meson_serial_console_init(); + if (ret) + return ret; + ret = uart_register_driver(&meson_uart_driver); if (ret) return ret; diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c index 87f005e5d2af..770c182e2208 100644 --- a/drivers/tty/serial/msm_serial.c +++ b/drivers/tty/serial/msm_serial.c @@ -426,7 +426,6 @@ static void msm_complete_tx_dma(void *args) struct circ_buf *xmit = &port->state->xmit; struct msm_dma *dma = &msm_port->tx_dma; struct dma_tx_state state; - enum dma_status status; unsigned long flags; unsigned int count; u32 val; @@ -437,7 +436,7 @@ static void msm_complete_tx_dma(void *args) if (!dma->count) goto done; - status = dmaengine_tx_status(dma->chan, dma->cookie, &state); + dmaengine_tx_status(dma->chan, dma->cookie, &state); dma_unmap_single(port->dev, dma->phys, dma->count, dma->dir); @@ -1525,7 +1524,7 @@ static void msm_poll_put_char(struct uart_port *port, unsigned char c) } #endif -static struct uart_ops msm_uart_pops = { +static const struct uart_ops msm_uart_pops = { .tx_empty = msm_tx_empty, .set_mctrl = msm_set_mctrl, .get_mctrl = msm_get_mctrl, diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c index b784323a6a7b..8ecf622602cb 100644 --- a/drivers/tty/serial/mxs-auart.c +++ b/drivers/tty/serial/mxs-auart.c @@ -443,24 +443,16 @@ struct mxs_auart_port { bool ms_irq_enabled; }; -static const struct platform_device_id mxs_auart_devtype[] = { - { .name = "mxs-auart-imx23", .driver_data = IMX23_AUART }, - { .name = "mxs-auart-imx28", .driver_data = IMX28_AUART }, - { .name = "as-auart-asm9260", .driver_data = ASM9260_AUART }, - { /* sentinel */ } -}; -MODULE_DEVICE_TABLE(platform, mxs_auart_devtype); - static const struct of_device_id mxs_auart_dt_ids[] = { { .compatible = "fsl,imx28-auart", - .data = &mxs_auart_devtype[IMX28_AUART] + .data = (const void *)IMX28_AUART }, { .compatible = "fsl,imx23-auart", - .data = &mxs_auart_devtype[IMX23_AUART] + .data = (const void *)IMX23_AUART }, { .compatible = "alphascale,asm9260-auart", - .data = &mxs_auart_devtype[ASM9260_AUART] + .data = (const void *)ASM9260_AUART }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids); @@ -1639,8 +1631,6 @@ static int mxs_auart_request_gpio_irq(struct mxs_auart_port *s) static int mxs_auart_probe(struct platform_device *pdev) { - const struct of_device_id *of_id = - of_match_device(mxs_auart_dt_ids, &pdev->dev); struct mxs_auart_port *s; u32 version; int ret, irq; @@ -1663,10 +1653,7 @@ static int mxs_auart_probe(struct platform_device *pdev) return -EINVAL; } - if (of_id) { - pdev->id_entry = of_id->data; - s->devtype = pdev->id_entry->driver_data; - } + s->devtype = (enum mxs_auart_type)of_device_get_match_data(&pdev->dev); ret = mxs_get_clks(s, pdev); if (ret) diff --git a/drivers/tty/serial/pmac_zilog.h b/drivers/tty/serial/pmac_zilog.h index bb874e76810e..fa85b0de5c2f 100644 --- a/drivers/tty/serial/pmac_zilog.h +++ b/drivers/tty/serial/pmac_zilog.h @@ -362,10 +362,10 @@ static inline void zssync(struct uart_pmac_port *port) /* Misc macros */ #define ZS_CLEARERR(port) (write_zsreg(port, 0, ERR_RES)) -#define ZS_CLEARFIFO(port) do { volatile unsigned char garbage; \ - garbage = read_zsdata(port); \ - garbage = read_zsdata(port); \ - garbage = read_zsdata(port); \ +#define ZS_CLEARFIFO(port) do { \ + read_zsdata(port); \ + read_zsdata(port); \ + read_zsdata(port); \ } while(0) #define ZS_IS_CONS(UP) ((UP)->flags & PMACZILOG_FLAG_IS_CONS) diff --git a/drivers/tty/serial/pnx8xxx_uart.c b/drivers/tty/serial/pnx8xxx_uart.c deleted file mode 100644 index 972d94e8d32b..000000000000 --- a/drivers/tty/serial/pnx8xxx_uart.c +++ /dev/null @@ -1,858 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * UART driver for PNX8XXX SoCs - * - * Author: Per Hallsmark per.hallsmark@mvista.com - * Ported to 2.6 kernel by EmbeddedAlley - * Reworked by Vitaly Wool <vitalywool@gmail.com> - * - * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. - * Copyright (C) 2000 Deep Blue Solutions Ltd. - */ - -#include <linux/module.h> -#include <linux/ioport.h> -#include <linux/init.h> -#include <linux/console.h> -#include <linux/sysrq.h> -#include <linux/device.h> -#include <linux/platform_device.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/serial_core.h> -#include <linux/serial.h> -#include <linux/serial_pnx8xxx.h> - -#include <asm/io.h> -#include <asm/irq.h> - -/* We'll be using StrongARM sa1100 serial port major/minor */ -#define SERIAL_PNX8XXX_MAJOR 204 -#define MINOR_START 5 - -#define NR_PORTS 2 - -#define PNX8XXX_ISR_PASS_LIMIT 256 - -/* - * Convert from ignore_status_mask or read_status_mask to FIFO - * and interrupt status bits - */ -#define SM_TO_FIFO(x) ((x) >> 10) -#define SM_TO_ISTAT(x) ((x) & 0x000001ff) -#define FIFO_TO_SM(x) ((x) << 10) -#define ISTAT_TO_SM(x) ((x) & 0x000001ff) - -/* - * This is the size of our serial port register set. - */ -#define UART_PORT_SIZE 0x1000 - -/* - * This determines how often we check the modem status signals - * for any change. They generally aren't connected to an IRQ - * so we have to poll them. We also check immediately before - * filling the TX fifo incase CTS has been dropped. - */ -#define MCTRL_TIMEOUT (250*HZ/1000) - -extern struct pnx8xxx_port pnx8xxx_ports[]; - -static inline int serial_in(struct pnx8xxx_port *sport, int offset) -{ - return (__raw_readl(sport->port.membase + offset)); -} - -static inline void serial_out(struct pnx8xxx_port *sport, int offset, int value) -{ - __raw_writel(value, sport->port.membase + offset); -} - -/* - * Handle any change of modem status signal since we were last called. - */ -static void pnx8xxx_mctrl_check(struct pnx8xxx_port *sport) -{ - unsigned int status, changed; - - status = sport->port.ops->get_mctrl(&sport->port); - changed = status ^ sport->old_status; - - if (changed == 0) - return; - - sport->old_status = status; - - if (changed & TIOCM_RI) - sport->port.icount.rng++; - if (changed & TIOCM_DSR) - sport->port.icount.dsr++; - if (changed & TIOCM_CAR) - uart_handle_dcd_change(&sport->port, status & TIOCM_CAR); - if (changed & TIOCM_CTS) - uart_handle_cts_change(&sport->port, status & TIOCM_CTS); - - wake_up_interruptible(&sport->port.state->port.delta_msr_wait); -} - -/* - * This is our per-port timeout handler, for checking the - * modem status signals. - */ -static void pnx8xxx_timeout(struct timer_list *t) -{ - struct pnx8xxx_port *sport = from_timer(sport, t, timer); - unsigned long flags; - - if (sport->port.state) { - spin_lock_irqsave(&sport->port.lock, flags); - pnx8xxx_mctrl_check(sport); - spin_unlock_irqrestore(&sport->port.lock, flags); - - mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT); - } -} - -/* - * interrupts disabled on entry - */ -static void pnx8xxx_stop_tx(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - u32 ien; - - /* Disable TX intr */ - ien = serial_in(sport, PNX8XXX_IEN); - serial_out(sport, PNX8XXX_IEN, ien & ~PNX8XXX_UART_INT_ALLTX); - - /* Clear all pending TX intr */ - serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLTX); -} - -/* - * interrupts may not be disabled on entry - */ -static void pnx8xxx_start_tx(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - u32 ien; - - /* Clear all pending TX intr */ - serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLTX); - - /* Enable TX intr */ - ien = serial_in(sport, PNX8XXX_IEN); - serial_out(sport, PNX8XXX_IEN, ien | PNX8XXX_UART_INT_ALLTX); -} - -/* - * Interrupts enabled - */ -static void pnx8xxx_stop_rx(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - u32 ien; - - /* Disable RX intr */ - ien = serial_in(sport, PNX8XXX_IEN); - serial_out(sport, PNX8XXX_IEN, ien & ~PNX8XXX_UART_INT_ALLRX); - - /* Clear all pending RX intr */ - serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX); -} - -/* - * Set the modem control timer to fire immediately. - */ -static void pnx8xxx_enable_ms(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - - mod_timer(&sport->timer, jiffies); -} - -static void pnx8xxx_rx_chars(struct pnx8xxx_port *sport) -{ - unsigned int status, ch, flg; - - status = FIFO_TO_SM(serial_in(sport, PNX8XXX_FIFO)) | - ISTAT_TO_SM(serial_in(sport, PNX8XXX_ISTAT)); - while (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFIFO)) { - ch = serial_in(sport, PNX8XXX_FIFO) & 0xff; - - sport->port.icount.rx++; - - flg = TTY_NORMAL; - - /* - * note that the error handling code is - * out of the main execution path - */ - if (status & (FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE | - PNX8XXX_UART_FIFO_RXPAR | - PNX8XXX_UART_FIFO_RXBRK) | - ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN))) { - if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXBRK)) { - status &= ~(FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) | - FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR)); - sport->port.icount.brk++; - if (uart_handle_break(&sport->port)) - goto ignore_char; - } else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR)) - sport->port.icount.parity++; - else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE)) - sport->port.icount.frame++; - if (status & ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN)) - sport->port.icount.overrun++; - - status &= sport->port.read_status_mask; - - if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR)) - flg = TTY_PARITY; - else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE)) - flg = TTY_FRAME; - - sport->port.sysrq = 0; - } - - if (uart_handle_sysrq_char(&sport->port, ch)) - goto ignore_char; - - uart_insert_char(&sport->port, status, - ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN), ch, flg); - - ignore_char: - serial_out(sport, PNX8XXX_LCR, serial_in(sport, PNX8XXX_LCR) | - PNX8XXX_UART_LCR_RX_NEXT); - status = FIFO_TO_SM(serial_in(sport, PNX8XXX_FIFO)) | - ISTAT_TO_SM(serial_in(sport, PNX8XXX_ISTAT)); - } - - spin_unlock(&sport->port.lock); - tty_flip_buffer_push(&sport->port.state->port); - spin_lock(&sport->port.lock); -} - -static void pnx8xxx_tx_chars(struct pnx8xxx_port *sport) -{ - struct circ_buf *xmit = &sport->port.state->xmit; - - if (sport->port.x_char) { - serial_out(sport, PNX8XXX_FIFO, sport->port.x_char); - sport->port.icount.tx++; - sport->port.x_char = 0; - return; - } - - /* - * Check the modem control lines before - * transmitting anything. - */ - pnx8xxx_mctrl_check(sport); - - if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) { - pnx8xxx_stop_tx(&sport->port); - return; - } - - /* - * TX while bytes available - */ - while (((serial_in(sport, PNX8XXX_FIFO) & - PNX8XXX_UART_FIFO_TXFIFO) >> 16) < 16) { - serial_out(sport, PNX8XXX_FIFO, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - sport->port.icount.tx++; - if (uart_circ_empty(xmit)) - break; - } - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(&sport->port); - - if (uart_circ_empty(xmit)) - pnx8xxx_stop_tx(&sport->port); -} - -static irqreturn_t pnx8xxx_int(int irq, void *dev_id) -{ - struct pnx8xxx_port *sport = dev_id; - unsigned int status; - - spin_lock(&sport->port.lock); - /* Get the interrupts */ - status = serial_in(sport, PNX8XXX_ISTAT) & serial_in(sport, PNX8XXX_IEN); - - /* Byte or break signal received */ - if (status & (PNX8XXX_UART_INT_RX | PNX8XXX_UART_INT_BREAK)) - pnx8xxx_rx_chars(sport); - - /* TX holding register empty - transmit a byte */ - if (status & PNX8XXX_UART_INT_TX) - pnx8xxx_tx_chars(sport); - - /* Clear the ISTAT register */ - serial_out(sport, PNX8XXX_ICLR, status); - - spin_unlock(&sport->port.lock); - return IRQ_HANDLED; -} - -/* - * Return TIOCSER_TEMT when transmitter is not busy. - */ -static unsigned int pnx8xxx_tx_empty(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - - return serial_in(sport, PNX8XXX_FIFO) & PNX8XXX_UART_FIFO_TXFIFO_STA ? 0 : TIOCSER_TEMT; -} - -static unsigned int pnx8xxx_get_mctrl(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - unsigned int mctrl = TIOCM_DSR; - unsigned int msr; - - /* REVISIT */ - - msr = serial_in(sport, PNX8XXX_MCR); - - mctrl |= msr & PNX8XXX_UART_MCR_CTS ? TIOCM_CTS : 0; - mctrl |= msr & PNX8XXX_UART_MCR_DCD ? TIOCM_CAR : 0; - - return mctrl; -} - -static void pnx8xxx_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ -#if 0 /* FIXME */ - struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port; - unsigned int msr; -#endif -} - -/* - * Interrupts always disabled. - */ -static void pnx8xxx_break_ctl(struct uart_port *port, int break_state) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - unsigned long flags; - unsigned int lcr; - - spin_lock_irqsave(&sport->port.lock, flags); - lcr = serial_in(sport, PNX8XXX_LCR); - if (break_state == -1) - lcr |= PNX8XXX_UART_LCR_TXBREAK; - else - lcr &= ~PNX8XXX_UART_LCR_TXBREAK; - serial_out(sport, PNX8XXX_LCR, lcr); - spin_unlock_irqrestore(&sport->port.lock, flags); -} - -static int pnx8xxx_startup(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - int retval; - - /* - * Allocate the IRQ - */ - retval = request_irq(sport->port.irq, pnx8xxx_int, 0, - "pnx8xxx-uart", sport); - if (retval) - return retval; - - /* - * Finally, clear and enable interrupts - */ - - serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX | - PNX8XXX_UART_INT_ALLTX); - - serial_out(sport, PNX8XXX_IEN, serial_in(sport, PNX8XXX_IEN) | - PNX8XXX_UART_INT_ALLRX | - PNX8XXX_UART_INT_ALLTX); - - /* - * Enable modem status interrupts - */ - spin_lock_irq(&sport->port.lock); - pnx8xxx_enable_ms(&sport->port); - spin_unlock_irq(&sport->port.lock); - - return 0; -} - -static void pnx8xxx_shutdown(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - int lcr; - - /* - * Stop our timer. - */ - del_timer_sync(&sport->timer); - - /* - * Disable all interrupts - */ - serial_out(sport, PNX8XXX_IEN, 0); - - /* - * Reset the Tx and Rx FIFOS, disable the break condition - */ - lcr = serial_in(sport, PNX8XXX_LCR); - lcr &= ~PNX8XXX_UART_LCR_TXBREAK; - lcr |= PNX8XXX_UART_LCR_TX_RST | PNX8XXX_UART_LCR_RX_RST; - serial_out(sport, PNX8XXX_LCR, lcr); - - /* - * Clear all interrupts - */ - serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX | - PNX8XXX_UART_INT_ALLTX); - - /* - * Free the interrupt - */ - free_irq(sport->port.irq, sport); -} - -static void -pnx8xxx_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - unsigned long flags; - unsigned int lcr_fcr, old_ien, baud, quot; - unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8; - - /* - * We only support CS7 and CS8. - */ - while ((termios->c_cflag & CSIZE) != CS7 && - (termios->c_cflag & CSIZE) != CS8) { - termios->c_cflag &= ~CSIZE; - termios->c_cflag |= old_csize; - old_csize = CS8; - } - - if ((termios->c_cflag & CSIZE) == CS8) - lcr_fcr = PNX8XXX_UART_LCR_8BIT; - else - lcr_fcr = 0; - - if (termios->c_cflag & CSTOPB) - lcr_fcr |= PNX8XXX_UART_LCR_2STOPB; - if (termios->c_cflag & PARENB) { - lcr_fcr |= PNX8XXX_UART_LCR_PAREN; - if (!(termios->c_cflag & PARODD)) - lcr_fcr |= PNX8XXX_UART_LCR_PAREVN; - } - - /* - * Ask the core to calculate the divisor for us. - */ - baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); - quot = uart_get_divisor(port, baud); - - spin_lock_irqsave(&sport->port.lock, flags); - - sport->port.read_status_mask = ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN) | - ISTAT_TO_SM(PNX8XXX_UART_INT_EMPTY) | - ISTAT_TO_SM(PNX8XXX_UART_INT_RX); - if (termios->c_iflag & INPCK) - sport->port.read_status_mask |= - FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) | - FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR); - if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) - sport->port.read_status_mask |= - ISTAT_TO_SM(PNX8XXX_UART_INT_BREAK); - - /* - * Characters to ignore - */ - sport->port.ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - sport->port.ignore_status_mask |= - FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) | - FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR); - if (termios->c_iflag & IGNBRK) { - sport->port.ignore_status_mask |= - ISTAT_TO_SM(PNX8XXX_UART_INT_BREAK); - /* - * If we're ignoring parity and break indicators, - * ignore overruns too (for real raw support). - */ - if (termios->c_iflag & IGNPAR) - sport->port.ignore_status_mask |= - ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN); - } - - /* - * ignore all characters if CREAD is not set - */ - if ((termios->c_cflag & CREAD) == 0) - sport->port.ignore_status_mask |= - ISTAT_TO_SM(PNX8XXX_UART_INT_RX); - - del_timer_sync(&sport->timer); - - /* - * Update the per-port timeout. - */ - uart_update_timeout(port, termios->c_cflag, baud); - - /* - * disable interrupts and drain transmitter - */ - old_ien = serial_in(sport, PNX8XXX_IEN); - serial_out(sport, PNX8XXX_IEN, old_ien & ~(PNX8XXX_UART_INT_ALLTX | - PNX8XXX_UART_INT_ALLRX)); - - while (serial_in(sport, PNX8XXX_FIFO) & PNX8XXX_UART_FIFO_TXFIFO_STA) - barrier(); - - /* then, disable everything */ - serial_out(sport, PNX8XXX_IEN, 0); - - /* Reset the Rx and Tx FIFOs too */ - lcr_fcr |= PNX8XXX_UART_LCR_TX_RST; - lcr_fcr |= PNX8XXX_UART_LCR_RX_RST; - - /* set the parity, stop bits and data size */ - serial_out(sport, PNX8XXX_LCR, lcr_fcr); - - /* set the baud rate */ - quot -= 1; - serial_out(sport, PNX8XXX_BAUD, quot); - - serial_out(sport, PNX8XXX_ICLR, -1); - - serial_out(sport, PNX8XXX_IEN, old_ien); - - if (UART_ENABLE_MS(&sport->port, termios->c_cflag)) - pnx8xxx_enable_ms(&sport->port); - - spin_unlock_irqrestore(&sport->port.lock, flags); -} - -static const char *pnx8xxx_type(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - - return sport->port.type == PORT_PNX8XXX ? "PNX8XXX" : NULL; -} - -/* - * Release the memory region(s) being used by 'port'. - */ -static void pnx8xxx_release_port(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - - release_mem_region(sport->port.mapbase, UART_PORT_SIZE); -} - -/* - * Request the memory region(s) being used by 'port'. - */ -static int pnx8xxx_request_port(struct uart_port *port) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - return request_mem_region(sport->port.mapbase, UART_PORT_SIZE, - "pnx8xxx-uart") != NULL ? 0 : -EBUSY; -} - -/* - * Configure/autoconfigure the port. - */ -static void pnx8xxx_config_port(struct uart_port *port, int flags) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - - if (flags & UART_CONFIG_TYPE && - pnx8xxx_request_port(&sport->port) == 0) - sport->port.type = PORT_PNX8XXX; -} - -/* - * Verify the new serial_struct (for TIOCSSERIAL). - * The only change we allow are to the flags and type, and - * even then only between PORT_PNX8XXX and PORT_UNKNOWN - */ -static int -pnx8xxx_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - int ret = 0; - - if (ser->type != PORT_UNKNOWN && ser->type != PORT_PNX8XXX) - ret = -EINVAL; - if (sport->port.irq != ser->irq) - ret = -EINVAL; - if (ser->io_type != SERIAL_IO_MEM) - ret = -EINVAL; - if (sport->port.uartclk / 16 != ser->baud_base) - ret = -EINVAL; - if ((void *)sport->port.mapbase != ser->iomem_base) - ret = -EINVAL; - if (sport->port.iobase != ser->port) - ret = -EINVAL; - if (ser->hub6 != 0) - ret = -EINVAL; - return ret; -} - -static const struct uart_ops pnx8xxx_pops = { - .tx_empty = pnx8xxx_tx_empty, - .set_mctrl = pnx8xxx_set_mctrl, - .get_mctrl = pnx8xxx_get_mctrl, - .stop_tx = pnx8xxx_stop_tx, - .start_tx = pnx8xxx_start_tx, - .stop_rx = pnx8xxx_stop_rx, - .enable_ms = pnx8xxx_enable_ms, - .break_ctl = pnx8xxx_break_ctl, - .startup = pnx8xxx_startup, - .shutdown = pnx8xxx_shutdown, - .set_termios = pnx8xxx_set_termios, - .type = pnx8xxx_type, - .release_port = pnx8xxx_release_port, - .request_port = pnx8xxx_request_port, - .config_port = pnx8xxx_config_port, - .verify_port = pnx8xxx_verify_port, -}; - - -/* - * Setup the PNX8XXX serial ports. - * - * Note also that we support "console=ttySx" where "x" is either 0 or 1. - */ -static void __init pnx8xxx_init_ports(void) -{ - static int first = 1; - int i; - - if (!first) - return; - first = 0; - - for (i = 0; i < NR_PORTS; i++) { - timer_setup(&pnx8xxx_ports[i].timer, pnx8xxx_timeout, 0); - pnx8xxx_ports[i].port.ops = &pnx8xxx_pops; - } -} - -#ifdef CONFIG_SERIAL_PNX8XXX_CONSOLE - -static void pnx8xxx_console_putchar(struct uart_port *port, int ch) -{ - struct pnx8xxx_port *sport = - container_of(port, struct pnx8xxx_port, port); - int status; - - do { - /* Wait for UART_TX register to empty */ - status = serial_in(sport, PNX8XXX_FIFO); - } while (status & PNX8XXX_UART_FIFO_TXFIFO); - serial_out(sport, PNX8XXX_FIFO, ch); -} - -/* - * Interrupts are disabled on entering - */static void -pnx8xxx_console_write(struct console *co, const char *s, unsigned int count) -{ - struct pnx8xxx_port *sport = &pnx8xxx_ports[co->index]; - unsigned int old_ien, status; - - /* - * First, save IEN and then disable interrupts - */ - old_ien = serial_in(sport, PNX8XXX_IEN); - serial_out(sport, PNX8XXX_IEN, old_ien & ~(PNX8XXX_UART_INT_ALLTX | - PNX8XXX_UART_INT_ALLRX)); - - uart_console_write(&sport->port, s, count, pnx8xxx_console_putchar); - - /* - * Finally, wait for transmitter to become empty - * and restore IEN - */ - do { - /* Wait for UART_TX register to empty */ - status = serial_in(sport, PNX8XXX_FIFO); - } while (status & PNX8XXX_UART_FIFO_TXFIFO); - - /* Clear TX and EMPTY interrupt */ - serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_TX | - PNX8XXX_UART_INT_EMPTY); - - serial_out(sport, PNX8XXX_IEN, old_ien); -} - -static int __init -pnx8xxx_console_setup(struct console *co, char *options) -{ - struct pnx8xxx_port *sport; - int baud = 38400; - int bits = 8; - int parity = 'n'; - int flow = 'n'; - - /* - * Check whether an invalid uart number has been specified, and - * if so, search for the first available port that does have - * console support. - */ - if (co->index == -1 || co->index >= NR_PORTS) - co->index = 0; - sport = &pnx8xxx_ports[co->index]; - - if (options) - uart_parse_options(options, &baud, &parity, &bits, &flow); - - return uart_set_options(&sport->port, co, baud, parity, bits, flow); -} - -static struct uart_driver pnx8xxx_reg; -static struct console pnx8xxx_console = { - .name = "ttyS", - .write = pnx8xxx_console_write, - .device = uart_console_device, - .setup = pnx8xxx_console_setup, - .flags = CON_PRINTBUFFER, - .index = -1, - .data = &pnx8xxx_reg, -}; - -static int __init pnx8xxx_rs_console_init(void) -{ - pnx8xxx_init_ports(); - register_console(&pnx8xxx_console); - return 0; -} -console_initcall(pnx8xxx_rs_console_init); - -#define PNX8XXX_CONSOLE &pnx8xxx_console -#else -#define PNX8XXX_CONSOLE NULL -#endif - -static struct uart_driver pnx8xxx_reg = { - .owner = THIS_MODULE, - .driver_name = "ttyS", - .dev_name = "ttyS", - .major = SERIAL_PNX8XXX_MAJOR, - .minor = MINOR_START, - .nr = NR_PORTS, - .cons = PNX8XXX_CONSOLE, -}; - -static int pnx8xxx_serial_suspend(struct platform_device *pdev, pm_message_t state) -{ - struct pnx8xxx_port *sport = platform_get_drvdata(pdev); - - return uart_suspend_port(&pnx8xxx_reg, &sport->port); -} - -static int pnx8xxx_serial_resume(struct platform_device *pdev) -{ - struct pnx8xxx_port *sport = platform_get_drvdata(pdev); - - return uart_resume_port(&pnx8xxx_reg, &sport->port); -} - -static int pnx8xxx_serial_probe(struct platform_device *pdev) -{ - struct resource *res = pdev->resource; - int i; - - for (i = 0; i < pdev->num_resources; i++, res++) { - if (!(res->flags & IORESOURCE_MEM)) - continue; - - for (i = 0; i < NR_PORTS; i++) { - if (pnx8xxx_ports[i].port.mapbase != res->start) - continue; - - pnx8xxx_ports[i].port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_PNX8XXX_CONSOLE); - pnx8xxx_ports[i].port.dev = &pdev->dev; - uart_add_one_port(&pnx8xxx_reg, &pnx8xxx_ports[i].port); - platform_set_drvdata(pdev, &pnx8xxx_ports[i]); - break; - } - } - - return 0; -} - -static int pnx8xxx_serial_remove(struct platform_device *pdev) -{ - struct pnx8xxx_port *sport = platform_get_drvdata(pdev); - - if (sport) - uart_remove_one_port(&pnx8xxx_reg, &sport->port); - - return 0; -} - -static struct platform_driver pnx8xxx_serial_driver = { - .driver = { - .name = "pnx8xxx-uart", - }, - .probe = pnx8xxx_serial_probe, - .remove = pnx8xxx_serial_remove, - .suspend = pnx8xxx_serial_suspend, - .resume = pnx8xxx_serial_resume, -}; - -static int __init pnx8xxx_serial_init(void) -{ - int ret; - - printk(KERN_INFO "Serial: PNX8XXX driver\n"); - - pnx8xxx_init_ports(); - - ret = uart_register_driver(&pnx8xxx_reg); - if (ret == 0) { - ret = platform_driver_register(&pnx8xxx_serial_driver); - if (ret) - uart_unregister_driver(&pnx8xxx_reg); - } - return ret; -} - -static void __exit pnx8xxx_serial_exit(void) -{ - platform_driver_unregister(&pnx8xxx_serial_driver); - uart_unregister_driver(&pnx8xxx_reg); -} - -module_init(pnx8xxx_serial_init); -module_exit(pnx8xxx_serial_exit); - -MODULE_AUTHOR("Embedded Alley Solutions, Inc."); -MODULE_DESCRIPTION("PNX8XXX SoCs serial port driver"); -MODULE_LICENSE("GPL"); -MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_PNX8XXX_MAJOR); -MODULE_ALIAS("platform:pnx8xxx-uart"); diff --git a/drivers/tty/serial/serial-tegra.c b/drivers/tty/serial/serial-tegra.c index bd13014a1c53..bbae072a125d 100644 --- a/drivers/tty/serial/serial-tegra.c +++ b/drivers/tty/serial/serial-tegra.c @@ -75,12 +75,17 @@ #define TEGRA_UART_FCR_IIR_FIFO_EN 0x40 /** - * tegra_uart_chip_data: SOC specific data. + * struct tegra_uart_chip_data: SOC specific data. * * @tx_fifo_full_status: Status flag available for checking tx fifo full. * @allow_txfifo_reset_fifo_mode: allow_tx fifo reset with fifo mode or not. * Tegra30 does not allow this. * @support_clk_src_div: Clock source support the clock divider. + * @fifo_mode_enable_status: Is FIFO mode enabled? + * @uart_max_port: Maximum number of UART ports + * @max_dma_burst_bytes: Maximum size of DMA bursts + * @error_tolerance_low_range: Lowest number in the error tolerance range + * @error_tolerance_high_range: Highest number in the error tolerance range */ struct tegra_uart_chip_data { bool tx_fifo_full_status; diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index f41cba10b86b..828f9ad1be49 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -1467,6 +1467,10 @@ static void uart_set_ldisc(struct tty_struct *tty) { struct uart_state *state = tty->driver_data; struct uart_port *uport; + struct tty_port *port = &state->port; + + if (!tty_port_initialized(port)) + return; mutex_lock(&state->port.mutex); uport = uart_port_check(state); diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c index fb4781292d40..c41d8911ce95 100644 --- a/drivers/tty/serial/serial_mctrl_gpio.c +++ b/drivers/tty/serial/serial_mctrl_gpio.c @@ -207,7 +207,7 @@ struct mctrl_gpios *mctrl_gpio_init(struct uart_port *port, unsigned int idx) continue; ret = gpiod_to_irq(gpios->gpio[i]); - if (ret <= 0) { + if (ret < 0) { dev_err(port->dev, "failed to find corresponding irq for %s (idx=%d, err=%d)\n", mctrl_gpios_desc[i].name, idx, ret); diff --git a/drivers/tty/serial/sifive.c b/drivers/tty/serial/sifive.c index 13eadcb8aec4..1066eebe3b28 100644 --- a/drivers/tty/serial/sifive.c +++ b/drivers/tty/serial/sifive.c @@ -144,12 +144,13 @@ */ /** - * sifive_serial_port - driver-specific data extension to struct uart_port + * struct sifive_serial_port - driver-specific data extension to struct uart_port * @port: struct uart_port embedded in this struct * @dev: struct device * * @ier: shadowed copy of the interrupt enable register * @clkin_rate: input clock to the UART IP block. * @baud_rate: UART serial line rate (e.g., 115200 baud) + * @clk: reference to this device's clock * @clk_notifier: clock rate change notifier for upstream clock changes * * Configuration data specific to this SiFive UART. diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c index ee6c7762d355..f4de32d3f2af 100644 --- a/drivers/tty/serial/stm32-usart.c +++ b/drivers/tty/serial/stm32-usart.c @@ -350,7 +350,6 @@ static void stm32_transmit_chars_dma(struct uart_port *port) struct stm32_usart_offsets *ofs = &stm32port->info->ofs; struct circ_buf *xmit = &port->state->xmit; struct dma_async_tx_descriptor *desc = NULL; - dma_cookie_t cookie; unsigned int count, i; if (stm32port->tx_dma_busy) @@ -394,7 +393,7 @@ static void stm32_transmit_chars_dma(struct uart_port *port) desc->callback_param = port; /* Push current DMA TX transaction in the pending queue */ - cookie = dmaengine_submit(desc); + dmaengine_submit(desc); /* Issue pending DMA TX requests */ dma_async_issue_pending(stm32port->tx_ch); @@ -1087,7 +1086,6 @@ static int stm32_of_dma_rx_probe(struct stm32_port *stm32port, struct device *dev = &pdev->dev; struct dma_slave_config config; struct dma_async_tx_descriptor *desc = NULL; - dma_cookie_t cookie; int ret; /* Request DMA RX channel */ @@ -1132,7 +1130,7 @@ static int stm32_of_dma_rx_probe(struct stm32_port *stm32port, desc->callback_param = NULL; /* Push current DMA transaction in the pending queue */ - cookie = dmaengine_submit(desc); + dmaengine_submit(desc); /* Issue pending DMA requests */ dma_async_issue_pending(stm32port->rx_ch); diff --git a/drivers/tty/serial/uartlite.c b/drivers/tty/serial/uartlite.c index 09379db613d8..f42ccc40ffa6 100644 --- a/drivers/tty/serial/uartlite.c +++ b/drivers/tty/serial/uartlite.c @@ -773,8 +773,8 @@ static int ulite_probe(struct platform_device *pdev) return -ENODEV; irq = platform_get_irq(pdev, 0); - if (irq <= 0) - return -ENXIO; + if (irq < 0) + return irq; pdata->clk = devm_clk_get(&pdev->dev, "s_axi_aclk"); if (IS_ERR(pdata->clk)) { diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c index a9b1ee27183a..a14c5d996473 100644 --- a/drivers/tty/serial/xilinx_uartps.c +++ b/drivers/tty/serial/xilinx_uartps.c @@ -192,6 +192,7 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255"); * @baud: Current baud rate * @clk_rate_change_nb: Notifier block for clock changes * @quirks: Flags for RXBS support. + * @cts_override: Modem control state override */ struct cdns_uart { struct uart_port *port; |