diff options
Diffstat (limited to 'drivers/mtd/nand/raw/qcom_nandc.c')
| -rw-r--r-- | drivers/mtd/nand/raw/qcom_nandc.c | 1092 |
1 files changed, 12 insertions, 1080 deletions
diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c index 6da5d23d2c8b..dcb62fd19dd7 100644 --- a/drivers/mtd/nand/raw/qcom_nandc.c +++ b/drivers/mtd/nand/raw/qcom_nandc.c @@ -15,417 +15,7 @@ #include <linux/of.h> #include <linux/platform_device.h> #include <linux/slab.h> - -/* NANDc reg offsets */ -#define NAND_FLASH_CMD 0x00 -#define NAND_ADDR0 0x04 -#define NAND_ADDR1 0x08 -#define NAND_FLASH_CHIP_SELECT 0x0c -#define NAND_EXEC_CMD 0x10 -#define NAND_FLASH_STATUS 0x14 -#define NAND_BUFFER_STATUS 0x18 -#define NAND_DEV0_CFG0 0x20 -#define NAND_DEV0_CFG1 0x24 -#define NAND_DEV0_ECC_CFG 0x28 -#define NAND_AUTO_STATUS_EN 0x2c -#define NAND_DEV1_CFG0 0x30 -#define NAND_DEV1_CFG1 0x34 -#define NAND_READ_ID 0x40 -#define NAND_READ_STATUS 0x44 -#define NAND_DEV_CMD0 0xa0 -#define NAND_DEV_CMD1 0xa4 -#define NAND_DEV_CMD2 0xa8 -#define NAND_DEV_CMD_VLD 0xac -#define SFLASHC_BURST_CFG 0xe0 -#define NAND_ERASED_CW_DETECT_CFG 0xe8 -#define NAND_ERASED_CW_DETECT_STATUS 0xec -#define NAND_EBI2_ECC_BUF_CFG 0xf0 -#define FLASH_BUF_ACC 0x100 - -#define NAND_CTRL 0xf00 -#define NAND_VERSION 0xf08 -#define NAND_READ_LOCATION_0 0xf20 -#define NAND_READ_LOCATION_1 0xf24 -#define NAND_READ_LOCATION_2 0xf28 -#define NAND_READ_LOCATION_3 0xf2c -#define NAND_READ_LOCATION_LAST_CW_0 0xf40 -#define NAND_READ_LOCATION_LAST_CW_1 0xf44 -#define NAND_READ_LOCATION_LAST_CW_2 0xf48 -#define NAND_READ_LOCATION_LAST_CW_3 0xf4c - -/* dummy register offsets, used by qcom_write_reg_dma */ -#define NAND_DEV_CMD1_RESTORE 0xdead -#define NAND_DEV_CMD_VLD_RESTORE 0xbeef - -/* NAND_FLASH_CMD bits */ -#define PAGE_ACC BIT(4) -#define LAST_PAGE BIT(5) - -/* NAND_FLASH_CHIP_SELECT bits */ -#define NAND_DEV_SEL 0 -#define DM_EN BIT(2) - -/* NAND_FLASH_STATUS bits */ -#define FS_OP_ERR BIT(4) -#define FS_READY_BSY_N BIT(5) -#define FS_MPU_ERR BIT(8) -#define FS_DEVICE_STS_ERR BIT(16) -#define FS_DEVICE_WP BIT(23) - -/* NAND_BUFFER_STATUS bits */ -#define BS_UNCORRECTABLE_BIT BIT(8) -#define BS_CORRECTABLE_ERR_MSK 0x1f - -/* NAND_DEVn_CFG0 bits */ -#define DISABLE_STATUS_AFTER_WRITE 4 -#define CW_PER_PAGE 6 -#define UD_SIZE_BYTES 9 -#define UD_SIZE_BYTES_MASK GENMASK(18, 9) -#define ECC_PARITY_SIZE_BYTES_RS 19 -#define SPARE_SIZE_BYTES 23 -#define SPARE_SIZE_BYTES_MASK GENMASK(26, 23) -#define NUM_ADDR_CYCLES 27 -#define STATUS_BFR_READ 30 -#define SET_RD_MODE_AFTER_STATUS 31 - -/* NAND_DEVn_CFG0 bits */ -#define DEV0_CFG1_ECC_DISABLE 0 -#define WIDE_FLASH 1 -#define NAND_RECOVERY_CYCLES 2 -#define CS_ACTIVE_BSY 5 -#define BAD_BLOCK_BYTE_NUM 6 -#define BAD_BLOCK_IN_SPARE_AREA 16 -#define WR_RD_BSY_GAP 17 -#define ENABLE_BCH_ECC 27 - -/* NAND_DEV0_ECC_CFG bits */ -#define ECC_CFG_ECC_DISABLE 0 -#define ECC_SW_RESET 1 -#define ECC_MODE 4 -#define ECC_PARITY_SIZE_BYTES_BCH 8 -#define ECC_NUM_DATA_BYTES 16 -#define ECC_NUM_DATA_BYTES_MASK GENMASK(25, 16) -#define ECC_FORCE_CLK_OPEN 30 - -/* NAND_DEV_CMD1 bits */ -#define READ_ADDR 0 - -/* NAND_DEV_CMD_VLD bits */ -#define READ_START_VLD BIT(0) -#define READ_STOP_VLD BIT(1) -#define WRITE_START_VLD BIT(2) -#define ERASE_START_VLD BIT(3) -#define SEQ_READ_START_VLD BIT(4) - -/* NAND_EBI2_ECC_BUF_CFG bits */ -#define NUM_STEPS 0 - -/* NAND_ERASED_CW_DETECT_CFG bits */ -#define ERASED_CW_ECC_MASK 1 -#define AUTO_DETECT_RES 0 -#define MASK_ECC BIT(ERASED_CW_ECC_MASK) -#define RESET_ERASED_DET BIT(AUTO_DETECT_RES) -#define ACTIVE_ERASED_DET (0 << AUTO_DETECT_RES) -#define CLR_ERASED_PAGE_DET (RESET_ERASED_DET | MASK_ECC) -#define SET_ERASED_PAGE_DET (ACTIVE_ERASED_DET | MASK_ECC) - -/* NAND_ERASED_CW_DETECT_STATUS bits */ -#define PAGE_ALL_ERASED BIT(7) -#define CODEWORD_ALL_ERASED BIT(6) -#define PAGE_ERASED BIT(5) -#define CODEWORD_ERASED BIT(4) -#define ERASED_PAGE (PAGE_ALL_ERASED | PAGE_ERASED) -#define ERASED_CW (CODEWORD_ALL_ERASED | CODEWORD_ERASED) - -/* NAND_READ_LOCATION_n bits */ -#define READ_LOCATION_OFFSET 0 -#define READ_LOCATION_SIZE 16 -#define READ_LOCATION_LAST 31 - -/* Version Mask */ -#define NAND_VERSION_MAJOR_MASK 0xf0000000 -#define NAND_VERSION_MAJOR_SHIFT 28 -#define NAND_VERSION_MINOR_MASK 0x0fff0000 -#define NAND_VERSION_MINOR_SHIFT 16 - -/* NAND OP_CMDs */ -#define OP_PAGE_READ 0x2 -#define OP_PAGE_READ_WITH_ECC 0x3 -#define OP_PAGE_READ_WITH_ECC_SPARE 0x4 -#define OP_PAGE_READ_ONFI_READ 0x5 -#define OP_PROGRAM_PAGE 0x6 -#define OP_PAGE_PROGRAM_WITH_ECC 0x7 -#define OP_PROGRAM_PAGE_SPARE 0x9 -#define OP_BLOCK_ERASE 0xa -#define OP_CHECK_STATUS 0xc -#define OP_FETCH_ID 0xb -#define OP_RESET_DEVICE 0xd - -/* Default Value for NAND_DEV_CMD_VLD */ -#define NAND_DEV_CMD_VLD_VAL (READ_START_VLD | WRITE_START_VLD | \ - ERASE_START_VLD | SEQ_READ_START_VLD) - -/* NAND_CTRL bits */ -#define BAM_MODE_EN BIT(0) - -/* - * the NAND controller performs reads/writes with ECC in 516 byte chunks. - * the driver calls the chunks 'step' or 'codeword' interchangeably - */ -#define NANDC_STEP_SIZE 512 - -/* - * the largest page size we support is 8K, this will have 16 steps/codewords - * of 512 bytes each - */ -#define MAX_NUM_STEPS (SZ_8K / NANDC_STEP_SIZE) - -/* we read at most 3 registers per codeword scan */ -#define MAX_REG_RD (3 * MAX_NUM_STEPS) - -/* ECC modes supported by the controller */ -#define ECC_NONE BIT(0) -#define ECC_RS_4BIT BIT(1) -#define ECC_BCH_4BIT BIT(2) -#define ECC_BCH_8BIT BIT(3) - -/* - * Returns the actual register address for all NAND_DEV_ registers - * (i.e. NAND_DEV_CMD0, NAND_DEV_CMD1, NAND_DEV_CMD2 and NAND_DEV_CMD_VLD) - */ -#define dev_cmd_reg_addr(nandc, reg) ((nandc)->props->dev_cmd_reg_start + (reg)) - -/* Returns the NAND register physical address */ -#define nandc_reg_phys(chip, offset) ((chip)->base_phys + (offset)) - -/* Returns the dma address for reg read buffer */ -#define reg_buf_dma_addr(chip, vaddr) \ - ((chip)->reg_read_dma + \ - ((u8 *)(vaddr) - (u8 *)(chip)->reg_read_buf)) - -#define QPIC_PER_CW_CMD_ELEMENTS 32 -#define QPIC_PER_CW_CMD_SGL 32 -#define QPIC_PER_CW_DATA_SGL 8 - -#define QPIC_NAND_COMPLETION_TIMEOUT msecs_to_jiffies(2000) - -/* - * Flags used in DMA descriptor preparation helper functions - * (i.e. qcom_read_reg_dma/qcom_write_reg_dma/qcom_read_data_dma/qcom_write_data_dma) - */ -/* Don't set the EOT in current tx BAM sgl */ -#define NAND_BAM_NO_EOT BIT(0) -/* Set the NWD flag in current BAM sgl */ -#define NAND_BAM_NWD BIT(1) -/* Finish writing in the current BAM sgl and start writing in another BAM sgl */ -#define NAND_BAM_NEXT_SGL BIT(2) -/* - * Erased codeword status is being used two times in single transfer so this - * flag will determine the current value of erased codeword status register - */ -#define NAND_ERASED_CW_SET BIT(4) - -#define MAX_ADDRESS_CYCLE 5 - -/* - * This data type corresponds to the BAM transaction which will be used for all - * NAND transfers. - * @bam_ce - the array of BAM command elements - * @cmd_sgl - sgl for NAND BAM command pipe - * @data_sgl - sgl for NAND BAM consumer/producer pipe - * @last_data_desc - last DMA desc in data channel (tx/rx). - * @last_cmd_desc - last DMA desc in command channel. - * @txn_done - completion for NAND transfer. - * @bam_ce_pos - the index in bam_ce which is available for next sgl - * @bam_ce_start - the index in bam_ce which marks the start position ce - * for current sgl. It will be used for size calculation - * for current sgl - * @cmd_sgl_pos - current index in command sgl. - * @cmd_sgl_start - start index in command sgl. - * @tx_sgl_pos - current index in data sgl for tx. - * @tx_sgl_start - start index in data sgl for tx. - * @rx_sgl_pos - current index in data sgl for rx. - * @rx_sgl_start - start index in data sgl for rx. - */ -struct bam_transaction { - struct bam_cmd_element *bam_ce; - struct scatterlist *cmd_sgl; - struct scatterlist *data_sgl; - struct dma_async_tx_descriptor *last_data_desc; - struct dma_async_tx_descriptor *last_cmd_desc; - struct completion txn_done; - u32 bam_ce_pos; - u32 bam_ce_start; - u32 cmd_sgl_pos; - u32 cmd_sgl_start; - u32 tx_sgl_pos; - u32 tx_sgl_start; - u32 rx_sgl_pos; - u32 rx_sgl_start; -}; - -/* - * This data type corresponds to the nand dma descriptor - * @dma_desc - low level DMA engine descriptor - * @list - list for desc_info - * - * @adm_sgl - sgl which will be used for single sgl dma descriptor. Only used by - * ADM - * @bam_sgl - sgl which will be used for dma descriptor. Only used by BAM - * @sgl_cnt - number of SGL in bam_sgl. Only used by BAM - * @dir - DMA transfer direction - */ -struct desc_info { - struct dma_async_tx_descriptor *dma_desc; - struct list_head node; - - union { - struct scatterlist adm_sgl; - struct { - struct scatterlist *bam_sgl; - int sgl_cnt; - }; - }; - enum dma_data_direction dir; -}; - -/* - * holds the current register values that we want to write. acts as a contiguous - * chunk of memory which we use to write the controller registers through DMA. - */ -struct nandc_regs { - __le32 cmd; - __le32 addr0; - __le32 addr1; - __le32 chip_sel; - __le32 exec; - - __le32 cfg0; - __le32 cfg1; - __le32 ecc_bch_cfg; - - __le32 clrflashstatus; - __le32 clrreadstatus; - - __le32 cmd1; - __le32 vld; - - __le32 orig_cmd1; - __le32 orig_vld; - - __le32 ecc_buf_cfg; - __le32 read_location0; - __le32 read_location1; - __le32 read_location2; - __le32 read_location3; - __le32 read_location_last0; - __le32 read_location_last1; - __le32 read_location_last2; - __le32 read_location_last3; - - __le32 erased_cw_detect_cfg_clr; - __le32 erased_cw_detect_cfg_set; -}; - -/* - * NAND controller data struct - * - * @dev: parent device - * - * @base: MMIO base - * - * @core_clk: controller clock - * @aon_clk: another controller clock - * - * @regs: a contiguous chunk of memory for DMA register - * writes. contains the register values to be - * written to controller - * - * @props: properties of current NAND controller, - * initialized via DT match data - * - * @controller: base controller structure - * @host_list: list containing all the chips attached to the - * controller - * - * @chan: dma channel - * @cmd_crci: ADM DMA CRCI for command flow control - * @data_crci: ADM DMA CRCI for data flow control - * - * @desc_list: DMA descriptor list (list of desc_infos) - * - * @data_buffer: our local DMA buffer for page read/writes, - * used when we can't use the buffer provided - * by upper layers directly - * @reg_read_buf: local buffer for reading back registers via DMA - * - * @base_phys: physical base address of controller registers - * @base_dma: dma base address of controller registers - * @reg_read_dma: contains dma address for register read buffer - * - * @buf_size/count/start: markers for chip->legacy.read_buf/write_buf - * functions - * @max_cwperpage: maximum QPIC codewords required. calculated - * from all connected NAND devices pagesize - * - * @reg_read_pos: marker for data read in reg_read_buf - * - * @cmd1/vld: some fixed controller register values - * - * @exec_opwrite: flag to select correct number of code word - * while reading status - */ -struct qcom_nand_controller { - struct device *dev; - - void __iomem *base; - - struct clk *core_clk; - struct clk *aon_clk; - - struct nandc_regs *regs; - struct bam_transaction *bam_txn; - - const struct qcom_nandc_props *props; - - struct nand_controller controller; - struct list_head host_list; - - union { - /* will be used only by QPIC for BAM DMA */ - struct { - struct dma_chan *tx_chan; - struct dma_chan *rx_chan; - struct dma_chan *cmd_chan; - }; - - /* will be used only by EBI2 for ADM DMA */ - struct { - struct dma_chan *chan; - unsigned int cmd_crci; - unsigned int data_crci; - }; - }; - - struct list_head desc_list; - - u8 *data_buffer; - __le32 *reg_read_buf; - - phys_addr_t base_phys; - dma_addr_t base_dma; - dma_addr_t reg_read_dma; - - int buf_size; - int buf_count; - int buf_start; - unsigned int max_cwperpage; - - int reg_read_pos; - - u32 cmd1, vld; - bool exec_opwrite; -}; +#include <linux/mtd/nand-qpic-common.h> /* * NAND special boot partitions @@ -530,97 +120,6 @@ struct qcom_nand_host { bool bch_enabled; }; -/* - * This data type corresponds to the NAND controller properties which varies - * among different NAND controllers. - * @ecc_modes - ecc mode for NAND - * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset - * @supports_bam - whether NAND controller is using Bus Access Manager (BAM) - * @nandc_part_of_qpic - whether NAND controller is part of qpic IP - * @qpic_version2 - flag to indicate QPIC IP version 2 - * @use_codeword_fixup - whether NAND has different layout for boot partitions - */ -struct qcom_nandc_props { - u32 ecc_modes; - u32 dev_cmd_reg_start; - bool supports_bam; - bool nandc_part_of_qpic; - bool qpic_version2; - bool use_codeword_fixup; -}; - -/* Frees the BAM transaction memory */ -static void qcom_free_bam_transaction(struct qcom_nand_controller *nandc) -{ - struct bam_transaction *bam_txn = nandc->bam_txn; - - devm_kfree(nandc->dev, bam_txn); -} - -/* Allocates and Initializes the BAM transaction */ -static struct bam_transaction * -qcom_alloc_bam_transaction(struct qcom_nand_controller *nandc) -{ - struct bam_transaction *bam_txn; - size_t bam_txn_size; - unsigned int num_cw = nandc->max_cwperpage; - void *bam_txn_buf; - - bam_txn_size = - sizeof(*bam_txn) + num_cw * - ((sizeof(*bam_txn->bam_ce) * QPIC_PER_CW_CMD_ELEMENTS) + - (sizeof(*bam_txn->cmd_sgl) * QPIC_PER_CW_CMD_SGL) + - (sizeof(*bam_txn->data_sgl) * QPIC_PER_CW_DATA_SGL)); - - bam_txn_buf = devm_kzalloc(nandc->dev, bam_txn_size, GFP_KERNEL); - if (!bam_txn_buf) - return NULL; - - bam_txn = bam_txn_buf; - bam_txn_buf += sizeof(*bam_txn); - - bam_txn->bam_ce = bam_txn_buf; - bam_txn_buf += - sizeof(*bam_txn->bam_ce) * QPIC_PER_CW_CMD_ELEMENTS * num_cw; - - bam_txn->cmd_sgl = bam_txn_buf; - bam_txn_buf += - sizeof(*bam_txn->cmd_sgl) * QPIC_PER_CW_CMD_SGL * num_cw; - - bam_txn->data_sgl = bam_txn_buf; - - init_completion(&bam_txn->txn_done); - - return bam_txn; -} - -/* Clears the BAM transaction indexes */ -static void qcom_clear_bam_transaction(struct qcom_nand_controller *nandc) -{ - struct bam_transaction *bam_txn = nandc->bam_txn; - - if (!nandc->props->supports_bam) - return; - - memset(&bam_txn->bam_ce_pos, 0, sizeof(u32) * 8); - bam_txn->last_data_desc = NULL; - - sg_init_table(bam_txn->cmd_sgl, nandc->max_cwperpage * - QPIC_PER_CW_CMD_SGL); - sg_init_table(bam_txn->data_sgl, nandc->max_cwperpage * - QPIC_PER_CW_DATA_SGL); - - reinit_completion(&bam_txn->txn_done); -} - -/* Callback for DMA descriptor completion */ -static void qcom_qpic_bam_dma_done(void *data) -{ - struct bam_transaction *bam_txn = data; - - complete(&bam_txn->txn_done); -} - static struct qcom_nand_host *to_qcom_nand_host(struct nand_chip *chip) { return container_of(chip, struct qcom_nand_host, chip); @@ -629,8 +128,8 @@ static struct qcom_nand_host *to_qcom_nand_host(struct nand_chip *chip) static struct qcom_nand_controller * get_qcom_nand_controller(struct nand_chip *chip) { - return container_of(chip->controller, struct qcom_nand_controller, - controller); + return (struct qcom_nand_controller *) + ((u8 *)chip->controller - sizeof(struct qcom_nand_controller)); } static u32 nandc_read(struct qcom_nand_controller *nandc, int offset) @@ -644,23 +143,6 @@ static void nandc_write(struct qcom_nand_controller *nandc, int offset, iowrite32(val, nandc->base + offset); } -static void qcom_nandc_dev_to_mem(struct qcom_nand_controller *nandc, bool is_cpu) -{ - if (!nandc->props->supports_bam) - return; - - if (is_cpu) - dma_sync_single_for_cpu(nandc->dev, nandc->reg_read_dma, - MAX_REG_RD * - sizeof(*nandc->reg_read_buf), - DMA_FROM_DEVICE); - else - dma_sync_single_for_device(nandc->dev, nandc->reg_read_dma, - MAX_REG_RD * - sizeof(*nandc->reg_read_buf), - DMA_FROM_DEVICE); -} - /* Helper to check whether this is the last CW or not */ static bool qcom_nandc_is_last_cw(struct nand_ecc_ctrl *ecc, int cw) { @@ -820,356 +302,6 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read, i } /* - * Maps the scatter gather list for DMA transfer and forms the DMA descriptor - * for BAM. This descriptor will be added in the NAND DMA descriptor queue - * which will be submitted to DMA engine. - */ -static int qcom_prepare_bam_async_desc(struct qcom_nand_controller *nandc, - struct dma_chan *chan, - unsigned long flags) -{ - struct desc_info *desc; - struct scatterlist *sgl; - unsigned int sgl_cnt; - int ret; - struct bam_transaction *bam_txn = nandc->bam_txn; - enum dma_transfer_direction dir_eng; - struct dma_async_tx_descriptor *dma_desc; - - desc = kzalloc(sizeof(*desc), GFP_KERNEL); - if (!desc) - return -ENOMEM; - - if (chan == nandc->cmd_chan) { - sgl = &bam_txn->cmd_sgl[bam_txn->cmd_sgl_start]; - sgl_cnt = bam_txn->cmd_sgl_pos - bam_txn->cmd_sgl_start; - bam_txn->cmd_sgl_start = bam_txn->cmd_sgl_pos; - dir_eng = DMA_MEM_TO_DEV; - desc->dir = DMA_TO_DEVICE; - } else if (chan == nandc->tx_chan) { - sgl = &bam_txn->data_sgl[bam_txn->tx_sgl_start]; - sgl_cnt = bam_txn->tx_sgl_pos - bam_txn->tx_sgl_start; - bam_txn->tx_sgl_start = bam_txn->tx_sgl_pos; - dir_eng = DMA_MEM_TO_DEV; - desc->dir = DMA_TO_DEVICE; - } else { - sgl = &bam_txn->data_sgl[bam_txn->rx_sgl_start]; - sgl_cnt = bam_txn->rx_sgl_pos - bam_txn->rx_sgl_start; - bam_txn->rx_sgl_start = bam_txn->rx_sgl_pos; - dir_eng = DMA_DEV_TO_MEM; - desc->dir = DMA_FROM_DEVICE; - } - - sg_mark_end(sgl + sgl_cnt - 1); - ret = dma_map_sg(nandc->dev, sgl, sgl_cnt, desc->dir); - if (ret == 0) { - dev_err(nandc->dev, "failure in mapping desc\n"); - kfree(desc); - return -ENOMEM; - } - - desc->sgl_cnt = sgl_cnt; - desc->bam_sgl = sgl; - - dma_desc = dmaengine_prep_slave_sg(chan, sgl, sgl_cnt, dir_eng, - flags); - - if (!dma_desc) { - dev_err(nandc->dev, "failure in prep desc\n"); - dma_unmap_sg(nandc->dev, sgl, sgl_cnt, desc->dir); - kfree(desc); - return -EINVAL; - } - - desc->dma_desc = dma_desc; - - /* update last data/command descriptor */ - if (chan == nandc->cmd_chan) - bam_txn->last_cmd_desc = dma_desc; - else - bam_txn->last_data_desc = dma_desc; - - list_add_tail(&desc->node, &nandc->desc_list); - - return 0; -} - -/* - * Prepares the command descriptor for BAM DMA which will be used for NAND - * register reads and writes. The command descriptor requires the command - * to be formed in command element type so this function uses the command - * element from bam transaction ce array and fills the same with required - * data. A single SGL can contain multiple command elements so - * NAND_BAM_NEXT_SGL will be used for starting the separate SGL - * after the current command element. - */ -static int qcom_prep_bam_dma_desc_cmd(struct qcom_nand_controller *nandc, bool read, - int reg_off, const void *vaddr, - int size, unsigned int flags) -{ - int bam_ce_size; - int i, ret; - struct bam_cmd_element *bam_ce_buffer; - struct bam_transaction *bam_txn = nandc->bam_txn; - - bam_ce_buffer = &bam_txn->bam_ce[bam_txn->bam_ce_pos]; - - /* fill the command desc */ - for (i = 0; i < size; i++) { - if (read) - bam_prep_ce(&bam_ce_buffer[i], - nandc_reg_phys(nandc, reg_off + 4 * i), - BAM_READ_COMMAND, - reg_buf_dma_addr(nandc, - (__le32 *)vaddr + i)); - else - bam_prep_ce_le32(&bam_ce_buffer[i], - nandc_reg_phys(nandc, reg_off + 4 * i), - BAM_WRITE_COMMAND, - *((__le32 *)vaddr + i)); - } - - bam_txn->bam_ce_pos += size; - - /* use the separate sgl after this command */ - if (flags & NAND_BAM_NEXT_SGL) { - bam_ce_buffer = &bam_txn->bam_ce[bam_txn->bam_ce_start]; - bam_ce_size = (bam_txn->bam_ce_pos - - bam_txn->bam_ce_start) * - sizeof(struct bam_cmd_element); - sg_set_buf(&bam_txn->cmd_sgl[bam_txn->cmd_sgl_pos], - bam_ce_buffer, bam_ce_size); - bam_txn->cmd_sgl_pos++; - bam_txn->bam_ce_start = bam_txn->bam_ce_pos; - - if (flags & NAND_BAM_NWD) { - ret = qcom_prepare_bam_async_desc(nandc, nandc->cmd_chan, - DMA_PREP_FENCE | - DMA_PREP_CMD); - if (ret) - return ret; - } - } - - return 0; -} - -/* - * Prepares the data descriptor for BAM DMA which will be used for NAND - * data reads and writes. - */ -static int qcom_prep_bam_dma_desc_data(struct qcom_nand_controller *nandc, bool read, - const void *vaddr, int size, unsigned int flags) -{ - int ret; - struct bam_transaction *bam_txn = nandc->bam_txn; - - if (read) { - sg_set_buf(&bam_txn->data_sgl[bam_txn->rx_sgl_pos], - vaddr, size); - bam_txn->rx_sgl_pos++; - } else { - sg_set_buf(&bam_txn->data_sgl[bam_txn->tx_sgl_pos], - vaddr, size); - bam_txn->tx_sgl_pos++; - - /* - * BAM will only set EOT for DMA_PREP_INTERRUPT so if this flag - * is not set, form the DMA descriptor - */ - if (!(flags & NAND_BAM_NO_EOT)) { - ret = qcom_prepare_bam_async_desc(nandc, nandc->tx_chan, - DMA_PREP_INTERRUPT); - if (ret) - return ret; - } - } - - return 0; -} - -static int qcom_prep_adm_dma_desc(struct qcom_nand_controller *nandc, bool read, - int reg_off, const void *vaddr, int size, - bool flow_control) -{ - struct desc_info *desc; - struct dma_async_tx_descriptor *dma_desc; - struct scatterlist *sgl; - struct dma_slave_config slave_conf; - struct qcom_adm_peripheral_config periph_conf = {}; - enum dma_transfer_direction dir_eng; - int ret; - - desc = kzalloc(sizeof(*desc), GFP_KERNEL); - if (!desc) - return -ENOMEM; - - sgl = &desc->adm_sgl; - - sg_init_one(sgl, vaddr, size); - - if (read) { - dir_eng = DMA_DEV_TO_MEM; - desc->dir = DMA_FROM_DEVICE; - } else { - dir_eng = DMA_MEM_TO_DEV; - desc->dir = DMA_TO_DEVICE; - } - - ret = dma_map_sg(nandc->dev, sgl, 1, desc->dir); - if (ret == 0) { - ret = -ENOMEM; - goto err; - } - - memset(&slave_conf, 0x00, sizeof(slave_conf)); - - slave_conf.device_fc = flow_control; - if (read) { - slave_conf.src_maxburst = 16; - slave_conf.src_addr = nandc->base_dma + reg_off; - if (nandc->data_crci) { - periph_conf.crci = nandc->data_crci; - slave_conf.peripheral_config = &periph_conf; - slave_conf.peripheral_size = sizeof(periph_conf); - } - } else { - slave_conf.dst_maxburst = 16; - slave_conf.dst_addr = nandc->base_dma + reg_off; - if (nandc->cmd_crci) { - periph_conf.crci = nandc->cmd_crci; - slave_conf.peripheral_config = &periph_conf; - slave_conf.peripheral_size = sizeof(periph_conf); - } - } - - ret = dmaengine_slave_config(nandc->chan, &slave_conf); - if (ret) { - dev_err(nandc->dev, "failed to configure dma channel\n"); - goto err; - } - - dma_desc = dmaengine_prep_slave_sg(nandc->chan, sgl, 1, dir_eng, 0); - if (!dma_desc) { - dev_err(nandc->dev, "failed to prepare desc\n"); - ret = -EINVAL; - goto err; - } - - desc->dma_desc = dma_desc; - - list_add_tail(&desc->node, &nandc->desc_list); - - return 0; -err: - kfree(desc); - - return ret; -} - -/* - * qcom_read_reg_dma: prepares a descriptor to read a given number of - * contiguous registers to the reg_read_buf pointer - * - * @first: offset of the first register in the contiguous block - * @num_regs: number of registers to read - * @flags: flags to control DMA descriptor preparation - */ -static int qcom_read_reg_dma(struct qcom_nand_controller *nandc, int first, - int num_regs, unsigned int flags) -{ - bool flow_control = false; - void *vaddr; - - vaddr = nandc->reg_read_buf + nandc->reg_read_pos; - nandc->reg_read_pos += num_regs; - - if (first == NAND_DEV_CMD_VLD || first == NAND_DEV_CMD1) - first = dev_cmd_reg_addr(nandc, first); - - if (nandc->props->supports_bam) - return qcom_prep_bam_dma_desc_cmd(nandc, true, first, vaddr, - num_regs, flags); - - if (first == NAND_READ_ID || first == NAND_FLASH_STATUS) - flow_control = true; - - return qcom_prep_adm_dma_desc(nandc, true, first, vaddr, - num_regs * sizeof(u32), flow_control); -} - -/* - * qcom_write_reg_dma: prepares a descriptor to write a given number of - * contiguous registers - * - * @vaddr: contiguous memory from where register value will - * be written - * @first: offset of the first register in the contiguous block - * @num_regs: number of registers to write - * @flags: flags to control DMA descriptor preparation - */ -static int qcom_write_reg_dma(struct qcom_nand_controller *nandc, __le32 *vaddr, - int first, int num_regs, unsigned int flags) -{ - bool flow_control = false; - - if (first == NAND_EXEC_CMD) - flags |= NAND_BAM_NWD; - - if (first == NAND_DEV_CMD1_RESTORE || first == NAND_DEV_CMD1) - first = dev_cmd_reg_addr(nandc, NAND_DEV_CMD1); - - if (first == NAND_DEV_CMD_VLD_RESTORE || first == NAND_DEV_CMD_VLD) - first = dev_cmd_reg_addr(nandc, NAND_DEV_CMD_VLD); - - if (nandc->props->supports_bam) - return qcom_prep_bam_dma_desc_cmd(nandc, false, first, vaddr, - num_regs, flags); - - if (first == NAND_FLASH_CMD) - flow_control = true; - - return qcom_prep_adm_dma_desc(nandc, false, first, vaddr, - num_regs * sizeof(u32), flow_control); -} - -/* - * qcom_read_data_dma: prepares a DMA descriptor to transfer data from the - * controller's internal buffer to the buffer 'vaddr' - * - * @reg_off: offset within the controller's data buffer - * @vaddr: virtual address of the buffer we want to write to - * @size: DMA transaction size in bytes - * @flags: flags to control DMA descriptor preparation - */ -static int qcom_read_data_dma(struct qcom_nand_controller *nandc, int reg_off, - const u8 *vaddr, int size, unsigned int flags) -{ - if (nandc->props->supports_bam) - return qcom_prep_bam_dma_desc_data(nandc, true, vaddr, size, flags); - - return qcom_prep_adm_dma_desc(nandc, true, reg_off, vaddr, size, false); -} - -/* - * qcom_write_data_dma: prepares a DMA descriptor to transfer data from - * 'vaddr' to the controller's internal buffer - * - * @reg_off: offset within the controller's data buffer - * @vaddr: virtual address of the buffer we want to read from - * @size: DMA transaction size in bytes - * @flags: flags to control DMA descriptor preparation - */ -static int qcom_write_data_dma(struct qcom_nand_controller *nandc, int reg_off, - const u8 *vaddr, int size, unsigned int flags) -{ - if (nandc->props->supports_bam) - return qcom_prep_bam_dma_desc_data(nandc, false, vaddr, size, flags); - - return qcom_prep_adm_dma_desc(nandc, false, reg_off, vaddr, size, false); -} - -/* * Helper to prepare DMA descriptors for configuring registers * before reading a NAND page. */ @@ -1262,83 +394,6 @@ static void config_nand_cw_write(struct nand_chip *chip) NAND_BAM_NEXT_SGL); } -/* helpers to submit/free our list of dma descriptors */ -static int qcom_submit_descs(struct qcom_nand_controller *nandc) -{ - struct desc_info *desc, *n; - dma_cookie_t cookie = 0; - struct bam_transaction *bam_txn = nandc->bam_txn; - int ret = 0; - - if (nandc->props->supports_bam) { - if (bam_txn->rx_sgl_pos > bam_txn->rx_sgl_start) { - ret = qcom_prepare_bam_async_desc(nandc, nandc->rx_chan, 0); - if (ret) - goto err_unmap_free_desc; - } - - if (bam_txn->tx_sgl_pos > bam_txn->tx_sgl_start) { - ret = qcom_prepare_bam_async_desc(nandc, nandc->tx_chan, - DMA_PREP_INTERRUPT); - if (ret) - goto err_unmap_free_desc; - } - - if (bam_txn->cmd_sgl_pos > bam_txn->cmd_sgl_start) { - ret = qcom_prepare_bam_async_desc(nandc, nandc->cmd_chan, - DMA_PREP_CMD); - if (ret) - goto err_unmap_free_desc; - } - } - - list_for_each_entry(desc, &nandc->desc_list, node) - cookie = dmaengine_submit(desc->dma_desc); - - if (nandc->props->supports_bam) { - bam_txn->last_cmd_desc->callback = qcom_qpic_bam_dma_done; - bam_txn->last_cmd_desc->callback_param = bam_txn; - - dma_async_issue_pending(nandc->tx_chan); - dma_async_issue_pending(nandc->rx_chan); - dma_async_issue_pending(nandc->cmd_chan); - - if (!wait_for_completion_timeout(&bam_txn->txn_done, - QPIC_NAND_COMPLETION_TIMEOUT)) - ret = -ETIMEDOUT; - } else { - if (dma_sync_wait(nandc->chan, cookie) != DMA_COMPLETE) - ret = -ETIMEDOUT; - } - -err_unmap_free_desc: - /* - * Unmap the dma sg_list and free the desc allocated by both - * qcom_prepare_bam_async_desc() and qcom_prep_adm_dma_desc() functions. - */ - list_for_each_entry_safe(desc, n, &nandc->desc_list, node) { - list_del(&desc->node); - - if (nandc->props->supports_bam) - dma_unmap_sg(nandc->dev, desc->bam_sgl, - desc->sgl_cnt, desc->dir); - else - dma_unmap_sg(nandc->dev, &desc->adm_sgl, 1, - desc->dir); - - kfree(desc); - } - - return ret; -} - -/* reset the register read buffer for next NAND operation */ -static void qcom_clear_read_regs(struct qcom_nand_controller *nandc) -{ - nandc->reg_read_pos = 0; - qcom_nandc_dev_to_mem(nandc, false); -} - /* * when using BCH ECC, the HW flags an error in NAND_FLASH_STATUS if it read * an erased CW, and reports an erased CW in NAND_ERASED_CW_DETECT_STATUS. @@ -2967,141 +2022,14 @@ static const struct nand_controller_ops qcom_nandc_ops = { .exec_op = qcom_nand_exec_op, }; -static void qcom_nandc_unalloc(struct qcom_nand_controller *nandc) -{ - if (nandc->props->supports_bam) { - if (!dma_mapping_error(nandc->dev, nandc->reg_read_dma)) - dma_unmap_single(nandc->dev, nandc->reg_read_dma, - MAX_REG_RD * - sizeof(*nandc->reg_read_buf), - DMA_FROM_DEVICE); - - if (nandc->tx_chan) - dma_release_channel(nandc->tx_chan); - - if (nandc->rx_chan) - dma_release_channel(nandc->rx_chan); - - if (nandc->cmd_chan) - dma_release_channel(nandc->cmd_chan); - } else { - if (nandc->chan) - dma_release_channel(nandc->chan); - } -} - -static int qcom_nandc_alloc(struct qcom_nand_controller *nandc) -{ - int ret; - - ret = dma_set_coherent_mask(nandc->dev, DMA_BIT_MASK(32)); - if (ret) { - dev_err(nandc->dev, "failed to set DMA mask\n"); - return ret; - } - - /* - * we use the internal buffer for reading ONFI params, reading small - * data like ID and status, and preforming read-copy-write operations - * when writing to a codeword partially. 532 is the maximum possible - * size of a codeword for our nand controller - */ - nandc->buf_size = 532; - - nandc->data_buffer = devm_kzalloc(nandc->dev, nandc->buf_size, GFP_KERNEL); - if (!nandc->data_buffer) - return -ENOMEM; - - nandc->regs = devm_kzalloc(nandc->dev, sizeof(*nandc->regs), GFP_KERNEL); - if (!nandc->regs) - return -ENOMEM; - - nandc->reg_read_buf = devm_kcalloc(nandc->dev, MAX_REG_RD, - sizeof(*nandc->reg_read_buf), - GFP_KERNEL); - if (!nandc->reg_read_buf) - return -ENOMEM; - - if (nandc->props->supports_bam) { - nandc->reg_read_dma = - dma_map_single(nandc->dev, nandc->reg_read_buf, - MAX_REG_RD * - sizeof(*nandc->reg_read_buf), - DMA_FROM_DEVICE); - if (dma_mapping_error(nandc->dev, nandc->reg_read_dma)) { - dev_err(nandc->dev, "failed to DMA MAP reg buffer\n"); - return -EIO; - } - - nandc->tx_chan = dma_request_chan(nandc->dev, "tx"); - if (IS_ERR(nandc->tx_chan)) { - ret = PTR_ERR(nandc->tx_chan); - nandc->tx_chan = NULL; - dev_err_probe(nandc->dev, ret, - "tx DMA channel request failed\n"); - goto unalloc; - } - - nandc->rx_chan = dma_request_chan(nandc->dev, "rx"); - if (IS_ERR(nandc->rx_chan)) { - ret = PTR_ERR(nandc->rx_chan); - nandc->rx_chan = NULL; - dev_err_probe(nandc->dev, ret, - "rx DMA channel request failed\n"); - goto unalloc; - } - - nandc->cmd_chan = dma_request_chan(nandc->dev, "cmd"); - if (IS_ERR(nandc->cmd_chan)) { - ret = PTR_ERR(nandc->cmd_chan); - nandc->cmd_chan = NULL; - dev_err_probe(nandc->dev, ret, - "cmd DMA channel request failed\n"); - goto unalloc; - } - - /* - * Initially allocate BAM transaction to read ONFI param page. - * After detecting all the devices, this BAM transaction will - * be freed and the next BAM transaction will be allocated with - * maximum codeword size - */ - nandc->max_cwperpage = 1; - nandc->bam_txn = qcom_alloc_bam_transaction(nandc); - if (!nandc->bam_txn) { - dev_err(nandc->dev, - "failed to allocate bam transaction\n"); - ret = -ENOMEM; - goto unalloc; - } - } else { - nandc->chan = dma_request_chan(nandc->dev, "rxtx"); - if (IS_ERR(nandc->chan)) { - ret = PTR_ERR(nandc->chan); - nandc->chan = NULL; - dev_err_probe(nandc->dev, ret, - "rxtx DMA channel request failed\n"); - return ret; - } - } - - INIT_LIST_HEAD(&nandc->desc_list); - INIT_LIST_HEAD(&nandc->host_list); - - nand_controller_init(&nandc->controller); - nandc->controller.ops = &qcom_nandc_ops; - - return 0; -unalloc: - qcom_nandc_unalloc(nandc); - return ret; -} - /* one time setup of a few nand controller registers */ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) { u32 nand_ctrl; + nand_controller_init(nandc->controller); + nandc->controller->ops = &qcom_nandc_ops; + /* kill onenand */ if (!nandc->props->nandc_part_of_qpic) nandc_write(nandc, SFLASHC_BURST_CFG, 0); @@ -3240,7 +2168,7 @@ static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, chip->legacy.block_bad = qcom_nandc_block_bad; chip->legacy.block_markbad = qcom_nandc_block_markbad; - chip->controller = &nandc->controller; + chip->controller = nandc->controller; chip->options |= NAND_NO_SUBPAGE_WRITE | NAND_USES_DMA | NAND_SKIP_BBTSCAN; @@ -3323,17 +2251,21 @@ static int qcom_nandc_parse_dt(struct platform_device *pdev) static int qcom_nandc_probe(struct platform_device *pdev) { struct qcom_nand_controller *nandc; + struct nand_controller *controller; const void *dev_data; struct device *dev = &pdev->dev; struct resource *res; int ret; - nandc = devm_kzalloc(&pdev->dev, sizeof(*nandc), GFP_KERNEL); + nandc = devm_kzalloc(&pdev->dev, sizeof(*nandc) + sizeof(*controller), + GFP_KERNEL); if (!nandc) return -ENOMEM; + controller = (struct nand_controller *)&nandc[1]; platform_set_drvdata(pdev, nandc); nandc->dev = dev; + nandc->controller = controller; dev_data = of_device_get_match_data(dev); if (!dev_data) { |