diff options
Diffstat (limited to 'arch/sh/include/asm/hd64465')
| -rw-r--r-- | arch/sh/include/asm/hd64465/gpio.h | 46 | ||||
| -rw-r--r-- | arch/sh/include/asm/hd64465/hd64465.h | 256 | ||||
| -rw-r--r-- | arch/sh/include/asm/hd64465/io.h | 44 |
3 files changed, 0 insertions, 346 deletions
diff --git a/arch/sh/include/asm/hd64465/gpio.h b/arch/sh/include/asm/hd64465/gpio.h deleted file mode 100644 index a3cdca2713dd..000000000000 --- a/arch/sh/include/asm/hd64465/gpio.h +++ /dev/null @@ -1,46 +0,0 @@ -#ifndef _ASM_SH_HD64465_GPIO_ -#define _ASM_SH_HD64465_GPIO_ 1 -/* - * $Id: gpio.h,v 1.3 2003/05/04 19:30:14 lethal Exp $ - * - * Hitachi HD64465 companion chip: General Purpose IO pins support. - * This layer enables other device drivers to configure GPIO - * pins, get and set their values, and register an interrupt - * routine for when input pins change in hardware. - * - * by Greg Banks <gbanks@pocketpenguins.com> - * (c) 2000 PocketPenguins Inc. - */ -#include <asm/hd64465.h> - -/* Macro to construct a portpin number (used in all - * subsequent functions) from a port letter and a pin - * number, e.g. HD64465_GPIO_PORTPIN('A', 5). - */ -#define HD64465_GPIO_PORTPIN(port,pin) (((port)-'A')<<3|(pin)) - -/* Pin configuration constants for _configure() */ -#define HD64465_GPIO_FUNCTION2 0 /* use the pin's *other* function */ -#define HD64465_GPIO_OUT 1 /* output */ -#define HD64465_GPIO_IN_PULLUP 2 /* input, pull-up MOS on */ -#define HD64465_GPIO_IN 3 /* input */ - -/* Configure a pin's direction */ -extern void hd64465_gpio_configure(int portpin, int direction); - -/* Get, set value */ -extern void hd64465_gpio_set_pin(int portpin, unsigned int value); -extern unsigned int hd64465_gpio_get_pin(int portpin); -extern void hd64465_gpio_set_port(int port, unsigned int value); -extern unsigned int hd64465_gpio_get_port(int port); - -/* mode constants for _register_irq() */ -#define HD64465_GPIO_FALLING 0 -#define HD64465_GPIO_RISING 1 - -/* Interrupt on external value change */ -extern void hd64465_gpio_register_irq(int portpin, int mode, - void (*handler)(int portpin, void *dev), void *dev); -extern void hd64465_gpio_unregister_irq(int portpin); - -#endif /* _ASM_SH_HD64465_GPIO_ */ diff --git a/arch/sh/include/asm/hd64465/hd64465.h b/arch/sh/include/asm/hd64465/hd64465.h deleted file mode 100644 index cfd0e803d2a2..000000000000 --- a/arch/sh/include/asm/hd64465/hd64465.h +++ /dev/null @@ -1,256 +0,0 @@ -#ifndef _ASM_SH_HD64465_ -#define _ASM_SH_HD64465_ 1 -/* - * $Id: hd64465.h,v 1.3 2003/05/04 19:30:15 lethal Exp $ - * - * Hitachi HD64465 companion chip support - * - * by Greg Banks <gbanks@pocketpenguins.com> - * (c) 2000 PocketPenguins Inc. - * - * Derived from <asm/hd64461.h> which bore the message: - * Copyright (C) 2000 YAEGASHI Takeshi - */ -#include <asm/io.h> -#include <asm/irq.h> - -/* - * Note that registers are defined here as virtual port numbers, - * which have no meaning except to get translated by hd64465_isa_port2addr() - * to an address in the range 0xb0000000-0xb3ffffff. Note that - * this translation happens to consist of adding the lower 16 bits - * of the virtual port number to 0xb0000000. Note also that the manual - * shows addresses as absolute physical addresses starting at 0x10000000, - * so e.g. the NIRR register is listed as 0x15000 here, 0x10005000 in the - * manual, and accessed using address 0xb0005000 - Greg. - */ - -/* System registers */ -#define HD64465_REG_SRR 0x1000c /* System Revision Register */ -#define HD64465_REG_SDID 0x10010 /* System Device ID Reg */ -#define HD64465_SDID 0x8122 /* 64465 device ID */ - -/* Power Management registers */ -#define HD64465_REG_SMSCR 0x10000 /* System Module Standby Control Reg */ -#define HD64465_SMSCR_PS2ST 0x4000 /* PS/2 Standby */ -#define HD64465_SMSCR_ADCST 0x1000 /* ADC Standby */ -#define HD64465_SMSCR_UARTST 0x0800 /* UART Standby */ -#define HD64465_SMSCR_SCDIST 0x0200 /* Serial Codec Standby */ -#define HD64465_SMSCR_PPST 0x0100 /* Parallel Port Standby */ -#define HD64465_SMSCR_PC0ST 0x0040 /* PCMCIA0 Standby */ -#define HD64465_SMSCR_PC1ST 0x0020 /* PCMCIA1 Standby */ -#define HD64465_SMSCR_AFEST 0x0010 /* AFE Standby */ -#define HD64465_SMSCR_TM0ST 0x0008 /* Timer0 Standby */ -#define HD64465_SMSCR_TM1ST 0x0004 /* Timer1 Standby */ -#define HD64465_SMSCR_IRDAST 0x0002 /* IRDA Standby */ -#define HD64465_SMSCR_KBCST 0x0001 /* Keyboard Controller Standby */ - -/* Interrupt Controller registers */ -#define HD64465_REG_NIRR 0x15000 /* Interrupt Request Register */ -#define HD64465_REG_NIMR 0x15002 /* Interrupt Mask Register */ -#define HD64465_REG_NITR 0x15004 /* Interrupt Trigger Mode Register */ - -/* Timer registers */ -#define HD64465_REG_TCVR1 0x16000 /* Timer 1 constant value register */ -#define HD64465_REG_TCVR0 0x16002 /* Timer 0 constant value register */ -#define HD64465_REG_TRVR1 0x16004 /* Timer 1 read value register */ -#define HD64465_REG_TRVR0 0x16006 /* Timer 0 read value register */ -#define HD64465_REG_TCR1 0x16008 /* Timer 1 control register */ -#define HD64465_REG_TCR0 0x1600A /* Timer 0 control register */ -#define HD64465_TCR_EADT 0x10 /* Enable ADTRIG# signal */ -#define HD64465_TCR_ETMO 0x08 /* Enable TMO signal */ -#define HD64465_TCR_PST_MASK 0x06 /* Clock Prescale */ -#define HD64465_TCR_PST_1 0x06 /* 1:1 */ -#define HD64465_TCR_PST_4 0x04 /* 1:4 */ -#define HD64465_TCR_PST_8 0x02 /* 1:8 */ -#define HD64465_TCR_PST_16 0x00 /* 1:16 */ -#define HD64465_TCR_TSTP 0x01 /* Start/Stop timer */ -#define HD64465_REG_TIRR 0x1600C /* Timer interrupt request register */ -#define HD64465_REG_TIDR 0x1600E /* Timer interrupt disable register */ -#define HD64465_REG_PWM1CS 0x16010 /* PWM 1 clock scale register */ -#define HD64465_REG_PWM1LPC 0x16012 /* PWM 1 low pulse width counter register */ -#define HD64465_REG_PWM1HPC 0x16014 /* PWM 1 high pulse width counter register */ -#define HD64465_REG_PWM0CS 0x16018 /* PWM 0 clock scale register */ -#define HD64465_REG_PWM0LPC 0x1601A /* PWM 0 low pulse width counter register */ -#define HD64465_REG_PWM0HPC 0x1601C /* PWM 0 high pulse width counter register */ - -/* Analog/Digital Converter registers */ -#define HD64465_REG_ADDRA 0x1E000 /* A/D data register A */ -#define HD64465_REG_ADDRB 0x1E002 /* A/D data register B */ -#define HD64465_REG_ADDRC 0x1E004 /* A/D data register C */ -#define HD64465_REG_ADDRD 0x1E006 /* A/D data register D */ -#define HD64465_REG_ADCSR 0x1E008 /* A/D control/status register */ -#define HD64465_ADCSR_ADF 0x80 /* A/D End Flag */ -#define HD64465_ADCSR_ADST 0x40 /* A/D Start Flag */ -#define HD64465_ADCSR_ADIS 0x20 /* A/D Interrupt Status */ -#define HD64465_ADCSR_TRGE 0x10 /* A/D Trigger Enable */ -#define HD64465_ADCSR_ADIE 0x08 /* A/D Interrupt Enable */ -#define HD64465_ADCSR_SCAN 0x04 /* A/D Scan Mode */ -#define HD64465_ADCSR_CH_MASK 0x03 /* A/D Channel */ -#define HD64465_REG_ADCALCR 0x1E00A /* A/D calibration sample control */ -#define HD64465_REG_ADCAL 0x1E00C /* A/D calibration data register */ - - -/* General Purpose I/O ports registers */ -#define HD64465_REG_GPACR 0x14000 /* Port A Control Register */ -#define HD64465_REG_GPBCR 0x14002 /* Port B Control Register */ -#define HD64465_REG_GPCCR 0x14004 /* Port C Control Register */ -#define HD64465_REG_GPDCR 0x14006 /* Port D Control Register */ -#define HD64465_REG_GPECR 0x14008 /* Port E Control Register */ -#define HD64465_REG_GPADR 0x14010 /* Port A Data Register */ -#define HD64465_REG_GPBDR 0x14012 /* Port B Data Register */ -#define HD64465_REG_GPCDR 0x14014 /* Port C Data Register */ -#define HD64465_REG_GPDDR 0x14016 /* Port D Data Register */ -#define HD64465_REG_GPEDR 0x14018 /* Port E Data Register */ -#define HD64465_REG_GPAICR 0x14020 /* Port A Interrupt Control Register */ -#define HD64465_REG_GPBICR 0x14022 /* Port B Interrupt Control Register */ -#define HD64465_REG_GPCICR 0x14024 /* Port C Interrupt Control Register */ -#define HD64465_REG_GPDICR 0x14026 /* Port D Interrupt Control Register */ -#define HD64465_REG_GPEICR 0x14028 /* Port E Interrupt Control Register */ -#define HD64465_REG_GPAISR 0x14040 /* Port A Interrupt Status Register */ -#define HD64465_REG_GPBISR 0x14042 /* Port B Interrupt Status Register */ -#define HD64465_REG_GPCISR 0x14044 /* Port C Interrupt Status Register */ -#define HD64465_REG_GPDISR 0x14046 /* Port D Interrupt Status Register */ -#define HD64465_REG_GPEISR 0x14048 /* Port E Interrupt Status Register */ - -/* PCMCIA bridge interface */ -#define HD64465_REG_PCC0ISR 0x12000 /* socket 0 interface status */ -#define HD64465_PCCISR_PREADY 0x80 /* mem card ready / io card IREQ */ -#define HD64465_PCCISR_PIREQ 0x80 -#define HD64465_PCCISR_PMWP 0x40 /* mem card write-protected */ -#define HD64465_PCCISR_PVS2 0x20 /* voltage select pin 2 */ -#define HD64465_PCCISR_PVS1 0x10 /* voltage select pin 1 */ -#define HD64465_PCCISR_PCD_MASK 0x0c /* card detect */ -#define HD64465_PCCISR_PBVD_MASK 0x03 /* battery voltage */ -#define HD64465_PCCISR_PBVD_BATGOOD 0x03 /* battery good */ -#define HD64465_PCCISR_PBVD_BATWARN 0x01 /* battery low warning */ -#define HD64465_PCCISR_PBVD_BATDEAD1 0x02 /* battery dead */ -#define HD64465_PCCISR_PBVD_BATDEAD2 0x00 /* battery dead */ -#define HD64465_REG_PCC0GCR 0x12002 /* socket 0 general control */ -#define HD64465_PCCGCR_PDRV 0x80 /* output drive */ -#define HD64465_PCCGCR_PCCR 0x40 /* PC card reset */ -#define HD64465_PCCGCR_PCCT 0x20 /* PC card type, 1=IO&mem, 0=mem */ -#define HD64465_PCCGCR_PVCC0 0x10 /* voltage control pin VCC0SEL0 */ -#define HD64465_PCCGCR_PMMOD 0x08 /* memory mode */ -#define HD64465_PCCGCR_PPA25 0x04 /* pin A25 */ -#define HD64465_PCCGCR_PPA24 0x02 /* pin A24 */ -#define HD64465_PCCGCR_PREG 0x01 /* ping PCC0REG# */ -#define HD64465_REG_PCC0CSCR 0x12004 /* socket 0 card status change */ -#define HD64465_PCCCSCR_PSCDI 0x80 /* sw card detect intr */ -#define HD64465_PCCCSCR_PSWSEL 0x40 /* power select */ -#define HD64465_PCCCSCR_PIREQ 0x20 /* IREQ intr req */ -#define HD64465_PCCCSCR_PSC 0x10 /* STSCHG (status change) pin */ -#define HD64465_PCCCSCR_PCDC 0x08 /* CD (card detect) change */ -#define HD64465_PCCCSCR_PRC 0x04 /* ready change */ -#define HD64465_PCCCSCR_PBW 0x02 /* battery warning change */ -#define HD64465_PCCCSCR_PBD 0x01 /* battery dead change */ -#define HD64465_REG_PCC0CSCIER 0x12006 /* socket 0 card status change interrupt enable */ -#define HD64465_PCCCSCIER_PCRE 0x80 /* change reset enable */ -#define HD64465_PCCCSCIER_PIREQE_MASK 0x60 /* IREQ enable */ -#define HD64465_PCCCSCIER_PIREQE_DISABLED 0x00 /* IREQ disabled */ -#define HD64465_PCCCSCIER_PIREQE_LEVEL 0x20 /* IREQ level-triggered */ -#define HD64465_PCCCSCIER_PIREQE_FALLING 0x40 /* IREQ falling-edge-trig */ -#define HD64465_PCCCSCIER_PIREQE_RISING 0x60 /* IREQ rising-edge-trig */ -#define HD64465_PCCCSCIER_PSCE 0x10 /* status change enable */ -#define HD64465_PCCCSCIER_PCDE 0x08 /* card detect change enable */ -#define HD64465_PCCCSCIER_PRE 0x04 /* ready change enable */ -#define HD64465_PCCCSCIER_PBWE 0x02 /* battery warn change enable */ -#define HD64465_PCCCSCIER_PBDE 0x01 /* battery dead change enable*/ -#define HD64465_REG_PCC0SCR 0x12008 /* socket 0 software control */ -#define HD64465_PCCSCR_SHDN 0x10 /* TPS2206 SHutDowN pin */ -#define HD64465_PCCSCR_SWP 0x01 /* write protect */ -#define HD64465_REG_PCCPSR 0x1200A /* serial power switch control */ -#define HD64465_REG_PCC1ISR 0x12010 /* socket 1 interface status */ -#define HD64465_REG_PCC1GCR 0x12012 /* socket 1 general control */ -#define HD64465_REG_PCC1CSCR 0x12014 /* socket 1 card status change */ -#define HD64465_REG_PCC1CSCIER 0x12016 /* socket 1 card status change interrupt enable */ -#define HD64465_REG_PCC1SCR 0x12018 /* socket 1 software control */ - - -/* PS/2 Keyboard and mouse controller -- *not* register compatible */ -#define HD64465_REG_KBCSR 0x1dc00 /* Keyboard Control/Status reg */ -#define HD64465_KBCSR_KBCIE 0x8000 /* KBCK Input Enable */ -#define HD64465_KBCSR_KBCOE 0x4000 /* KBCK Output Enable */ -#define HD64465_KBCSR_KBDOE 0x2000 /* KB DATA Output Enable */ -#define HD64465_KBCSR_KBCD 0x1000 /* KBCK Driven */ -#define HD64465_KBCSR_KBDD 0x0800 /* KB DATA Driven */ -#define HD64465_KBCSR_KBCS 0x0400 /* KBCK pin Status */ -#define HD64465_KBCSR_KBDS 0x0200 /* KB DATA pin Status */ -#define HD64465_KBCSR_KBDP 0x0100 /* KB DATA Parity bit */ -#define HD64465_KBCSR_KBD_MASK 0x00ff /* KD DATA shift reg */ -#define HD64465_REG_KBISR 0x1dc04 /* Keyboard Interrupt Status reg */ -#define HD64465_KBISR_KBRDF 0x0001 /* KB Received Data Full */ -#define HD64465_REG_MSCSR 0x1dc10 /* Mouse Control/Status reg */ -#define HD64465_REG_MSISR 0x1dc14 /* Mouse Interrupt Status reg */ - - -/* - * Logical address at which the HD64465 is mapped. Note that this - * should always be in the P2 segment (uncached and untranslated). - */ -#ifndef CONFIG_HD64465_IOBASE -#define CONFIG_HD64465_IOBASE 0xb0000000 -#endif -/* - * The HD64465 multiplexes all its modules' interrupts onto - * this single interrupt. - */ -#ifndef CONFIG_HD64465_IRQ -#define CONFIG_HD64465_IRQ 5 -#endif - - -#define _HD64465_IO_MASK 0xf8000000 -#define is_hd64465_addr(addr) \ - ((addr & _HD64465_IO_MASK) == (CONFIG_HD64465_IOBASE & _HD64465_IO_MASK)) - -/* - * A range of 16 virtual interrupts generated by - * demuxing the HD64465 muxed interrupt. - */ -#define HD64465_IRQ_BASE OFFCHIP_IRQ_BASE -#define HD64465_IRQ_NUM 16 -#define HD64465_IRQ_ADC (HD64465_IRQ_BASE+0) -#define HD64465_IRQ_USB (HD64465_IRQ_BASE+1) -#define HD64465_IRQ_SCDI (HD64465_IRQ_BASE+2) -#define HD64465_IRQ_PARALLEL (HD64465_IRQ_BASE+3) -/* bit 4 is reserved */ -#define HD64465_IRQ_UART (HD64465_IRQ_BASE+5) -#define HD64465_IRQ_IRDA (HD64465_IRQ_BASE+6) -#define HD64465_IRQ_PS2MOUSE (HD64465_IRQ_BASE+7) -#define HD64465_IRQ_KBC (HD64465_IRQ_BASE+8) -#define HD64465_IRQ_TIMER1 (HD64465_IRQ_BASE+9) -#define HD64465_IRQ_TIMER0 (HD64465_IRQ_BASE+10) -#define HD64465_IRQ_GPIO (HD64465_IRQ_BASE+11) -#define HD64465_IRQ_AFE (HD64465_IRQ_BASE+12) -#define HD64465_IRQ_PCMCIA1 (HD64465_IRQ_BASE+13) -#define HD64465_IRQ_PCMCIA0 (HD64465_IRQ_BASE+14) -#define HD64465_IRQ_PS2KBD (HD64465_IRQ_BASE+15) - -/* Constants for PCMCIA mappings */ -#define HD64465_PCC_WINDOW 0x01000000 - -#define HD64465_PCC0_BASE 0xb8000000 /* area 6 */ -#define HD64465_PCC0_ATTR (HD64465_PCC0_BASE) -#define HD64465_PCC0_COMM (HD64465_PCC0_BASE+HD64465_PCC_WINDOW) -#define HD64465_PCC0_IO (HD64465_PCC0_BASE+2*HD64465_PCC_WINDOW) - -#define HD64465_PCC1_BASE 0xb4000000 /* area 5 */ -#define HD64465_PCC1_ATTR (HD64465_PCC1_BASE) -#define HD64465_PCC1_COMM (HD64465_PCC1_BASE+HD64465_PCC_WINDOW) -#define HD64465_PCC1_IO (HD64465_PCC1_BASE+2*HD64465_PCC_WINDOW) - -/* - * Base of USB controller interface (as memory) - */ -#define HD64465_USB_BASE (CONFIG_HD64465_IOBASE+0xb000) -#define HD64465_USB_LEN 0x1000 -/* - * Base of embedded SRAM, used for USB controller. - */ -#define HD64465_SRAM_BASE (CONFIG_HD64465_IOBASE+0x9000) -#define HD64465_SRAM_LEN 0x1000 - - - -#endif /* _ASM_SH_HD64465_ */ diff --git a/arch/sh/include/asm/hd64465/io.h b/arch/sh/include/asm/hd64465/io.h deleted file mode 100644 index 139f1472e5bb..000000000000 --- a/arch/sh/include/asm/hd64465/io.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * include/asm-sh/hd64465/io.h - * - * By Greg Banks <gbanks@pocketpenguins.com> - * (c) 2000 PocketPenguins Inc. - * - * Derived from io_hd64461.h, which bore the message: - * Copyright 2000 Stuart Menefy (stuart.menefy@st.com) - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - * - * IO functions for an HD64465 "Windows CE Intelligent Peripheral Controller". - */ - -#ifndef _ASM_SH_IO_HD64465_H -#define _ASM_SH_IO_HD64465_H - -extern unsigned char hd64465_inb(unsigned long port); -extern unsigned short hd64465_inw(unsigned long port); -extern unsigned int hd64465_inl(unsigned long port); - -extern void hd64465_outb(unsigned char value, unsigned long port); -extern void hd64465_outw(unsigned short value, unsigned long port); -extern void hd64465_outl(unsigned int value, unsigned long port); - -extern unsigned char hd64465_inb_p(unsigned long port); -extern void hd64465_outb_p(unsigned char value, unsigned long port); - -extern unsigned long hd64465_isa_port2addr(unsigned long offset); -extern int hd64465_irq_demux(int irq); -/* Provision for generic secondary demux step -- used by PCMCIA code */ -extern void hd64465_register_irq_demux(int irq, - int (*demux)(int irq, void *dev), void *dev); -extern void hd64465_unregister_irq_demux(int irq); -/* Set this variable to 1 to see port traffic */ -extern int hd64465_io_debug; -/* Map a range of ports to a range of kernel virtual memory. - */ -extern void hd64465_port_map(unsigned short baseport, unsigned int nports, - unsigned long addr, unsigned char shift); -extern void hd64465_port_unmap(unsigned short baseport, unsigned int nports); - -#endif /* _ASM_SH_IO_HD64465_H */ |