summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/boot/dts/qcom-apq8060-dragonboard.dts')
-rw-r--r--arch/arm/boot/dts/qcom-apq8060-dragonboard.dts1754
1 files changed, 861 insertions, 893 deletions
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index 573e4dc66bb0..7a4c59e04af6 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -81,931 +81,899 @@
pinctrl-names = "default";
pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
};
+};
- soc {
- pinctrl@800000 {
- /* eMMC pins, all 8 data lines connected */
- dragon_sdcc1_pins: sdcc1 {
- mux {
- pins = "gpio159", "gpio160", "gpio161",
- "gpio162", "gpio163", "gpio164",
- "gpio165", "gpio166", "gpio167",
- "gpio168";
- function = "sdc1";
- };
- clk {
- pins = "gpio167"; /* SDC1 CLK */
- drive-strength = <16>;
- bias-disable;
- };
- cmd {
- pins = "gpio168"; /* SDC1 CMD */
- drive-strength = <10>;
- bias-pull-up;
- };
- data {
- /* SDC1 D0 to D7 */
- pins = "gpio159", "gpio160", "gpio161", "gpio162",
- "gpio163", "gpio164", "gpio165", "gpio166";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
+&ebi2 {
+ /* The EBI2 will instantiate first, then populate its children */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_ebi2_pins>;
+ status = "okay";
- /*
- * The SDCC3 pins are hardcoded (non-muxable) but need some pin
- * configuration.
- */
- dragon_sdcc3_pins: sdcc3 {
- clk {
- pins = "sdc3_clk";
- drive-strength = <8>;
- bias-disable;
- };
- cmd {
- pins = "sdc3_cmd";
- drive-strength = <8>;
- bias-pull-up;
- };
- data {
- pins = "sdc3_data";
- drive-strength = <8>;
- bias-pull-up;
- };
- };
+ /*
+ * An on-board SMSC LAN9221 chip for "debug ethernet",
+ * which is actually just an ordinary ethernet on the
+ * EBI2. This has a 25MHz chrystal next to it, so no
+ * clocking is needed.
+ */
+ ethernet@2,0 {
+ compatible = "smsc,lan9221", "smsc,lan9115";
+ reg = <2 0x0 0x100>;
+ /*
+ * The second interrupt is the PME interrupt
+ * for network wakeup, connected to the TLMM.
+ */
+ interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
+ <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
+ reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+ vdd33a-supply = <&dragon_veth>;
+ vddvario-supply = <&dragon_vario>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_ethernet_gpios>;
+ phy-mode = "mii";
+ reg-io-width = <2>;
+ smsc,force-external-phy;
+ smsc,irq-push-pull;
+
+ /*
+ * SLOW chipselect config
+ * Delay 9 cycles (140ns@64MHz) between SMSC
+ * LAN9221 Ethernet controller reads and writes
+ * on CS2.
+ */
+ qcom,xmem-recovery-cycles = <0>;
+ qcom,xmem-write-hold-cycles = <3>;
+ qcom,xmem-write-delta-cycles = <31>;
+ qcom,xmem-read-delta-cycles = <28>;
+ qcom,xmem-write-wait-cycles = <9>;
+ qcom,xmem-read-wait-cycles = <9>;
+ };
+};
- /* Second SD card slot pins */
- dragon_sdcc5_pins: sdcc5 {
- mux {
- pins = "gpio95", "gpio96", "gpio97",
- "gpio98", "gpio99", "gpio100";
- function = "sdc5";
- };
- clk {
- pins = "gpio97"; /* SDC5 CLK */
- drive-strength = <16>;
- bias-disable;
- };
- cmd {
- pins = "gpio95"; /* SDC5 CMD */
- drive-strength = <10>;
- bias-pull-up;
- };
- data {
- /* SDC5 D0 to D3 */
- pins = "gpio96", "gpio98", "gpio99", "gpio100";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
+&gsbi3 {
+ qcom,mode = <GSBI_PROT_I2C>;
+ status = "okay";
+};
- dragon_gsbi3_i2c_pins: gsbi3_i2c {
- mux {
- pins = "gpio43", "gpio44";
- function = "gsbi3";
- };
- pinconf {
- pins = "gpio43", "gpio44";
- drive-strength = <8>;
- /* These have external pull-up 2.2kOhm to 1.8V */
- bias-disable;
- };
- };
+&gsbi3_i2c {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
+ status = "okay";
+
+ touchscreen@24 {
+ compatible = "cypress,cy8ctma340";
+ reg = <0x24>;
+ /* Certainly we can do at least 400 kHz */
+ clock-frequency = <400000>;
+ /* IRQ on GPIO61 called /CTP_INT */
+ interrupt-parent = <&tlmm>;
+ interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+ /*
+ * The I2C bus is using a PCA9306 level translator from L16A
+ * to L2B so these two voltages are needed and L16A is
+ * kind of the IO voltage, however L16Aisn't really fed to
+ * the TMA340, which relies entirely on L2B (PM8901 L2).
+ */
+ vcpin-supply = <&pm8058_l16>;
+ vdd-supply = <&pm8901_l2>;
+ /* GPIO58, called WAKE_CTP */
+ reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ touchscreen-size-x = <480>;
+ touchscreen-size-y = <800>;
+ active-interval-ms = <0>;
+ touch-timeout-ms = <255>;
+ lowpower-interval-ms = <10>;
+ bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_tma340_gpios>;
+ };
+};
- dragon_gsbi8_i2c_pins: gsbi8_i2c {
- mux {
- pins = "gpio64", "gpio65";
- function = "gsbi8";
- };
- pinconf {
- pins = "gpio64", "gpio65";
- drive-strength = <16>;
- /* These have external pull-up 2.2kOhm to 1.8V */
- bias-disable;
- };
- };
+&gsbi8 {
+ qcom,mode = <GSBI_PROT_I2C>;
+ status = "okay";
+};
- dragon_gsbi12_i2c_pins: gsbi12_i2c {
- mux {
- pins = "gpio115", "gpio116";
- function = "gsbi12";
- };
- pinconf {
- pins = "gpio115", "gpio116";
- drive-strength = <16>;
- /* These have external pull-up 4.7kOhm to 1.8V */
- bias-disable;
- };
- };
+&gsbi8_i2c {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+ status = "okay";
+
+ eeprom@52 {
+ /* A 16KiB Platform ID EEPROM on the CPU carrier board */
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ vcc-supply = <&pm8058_s3>;
+ pagesize = <64>;
+ };
+ wm8903: wm8903@1a {
+ /* This Woolfson Micro device has an unrouted interrupt line */
+ compatible = "wlf,wm8903";
+ reg = <0x1a>;
+
+ AVDD-supply = <&pm8058_l16>;
+ CPVDD-supply = <&pm8058_l16>;
+ DBVDD-supply = <&pm8058_s3>;
+ DCVDD-supply = <&pm8058_l0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+ };
+};
- /* Primary serial port uart 0 pins */
- dragon_gsbi12_serial_pins: gsbi12_serial {
- mux {
- pins = "gpio117", "gpio118";
- function = "gsbi12";
- };
- tx {
- pins = "gpio117";
- drive-strength = <8>;
- bias-disable;
- };
- rx {
- pins = "gpio118";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
+&gsbi12 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+};
- dragon_ebi2_pins: ebi2 {
- /*
- * Pins used by EBI2 on the Dragonboard, actually only
- * CS2 is used by a real peripheral. CS0 is just
- * routed to a test point.
- */
- mux0 {
- pins =
- /* "gpio39", CS1A_N this is not good to mux */
- "gpio40", /* CS2A_N */
- "gpio134"; /* CS0_N testpoint TP29 */
- function = "ebi2cs";
- };
- mux1 {
- pins =
- /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
- "gpio123", "gpio124", "gpio125", "gpio126",
- "gpio127", "gpio128", "gpio129", "gpio130",
- /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
- "gpio135", "gpio136", "gpio137", "gpio138",
- "gpio139", "gpio140", "gpio141", "gpio142",
- "gpio143", "gpio144", "gpio145", "gpio146",
- "gpio147", "gpio148", "gpio149", "gpio150",
- "gpio151", /* EBI2_OE_N */
- "gpio153", /* EBI2_ADV */
- "gpio157"; /* EBI2_WE_N */
- function = "ebi2";
- };
- };
+&gsbi12_serial {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+ status = "okay";
+};
- /* Interrupt line for the KXSD9 accelerometer */
- dragon_kxsd9_gpios: kxsd9 {
- irq {
- pins = "gpio57"; /* IRQ line */
- bias-pull-up;
- };
- };
+&gsbi12_i2c {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+ status = "okay";
+
+ ak8975@c {
+ compatible = "asahi-kasei,ak8975";
+ reg = <0x0c>;
+ interrupt-parent = <&pm8058_gpio>;
+ interrupts = <33 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_ak8975_gpios>;
+ vid-supply = <&pm8058_lvs0>; // 1.8V
+ vdd-supply = <&pm8058_l14>; // 2.85V
+ };
+ bmp085@77 {
+ compatible = "bosch,bmp085";
+ reg = <0x77>;
+ interrupt-parent = <&pm8058_gpio>;
+ interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+ reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_bmp085_gpios>;
+ vddd-supply = <&pm8058_lvs0>; // 1.8V
+ vdda-supply = <&pm8058_l14>; // 2.85V
+ };
+ mpu3050@68 {
+ compatible = "invensense,mpu3050";
+ reg = <0x68>;
+ /*
+ * GPIO17 is pulled high by a 10k
+ * resistor to VLOGIC so needs to be
+ * active low/falling edge.
+ */
+ interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_mpu3050_gpios>;
+ vlogic-supply = <&pm8058_lvs0>; // 1.8V
+ vdd-supply = <&pm8058_l14>; // 2.85V
- dragon_tma340_gpios: tma340 {
- reset {
- /* RESET line, TS_ATTN, WAKE_CTP */
- pins = "gpio58";
- function = "gpio";
- drive-strength = <6>;
- bias-disable;
- };
- irq {
- pins = "gpio61"; /* IRQ line */
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
+ /*
+ * The MPU-3050 acts as a hub for the
+ * accelerometer.
+ */
+ i2c-gate {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ kxsd9@18 {
+ compatible = "kionix,kxsd9";
+ reg = <0x18>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_kxsd9_gpios>;
+ iovdd-supply = <&pm8058_lvs0>; // 1.8V
+ vdd-supply = <&pm8058_l14>; // 2.85V
};
};
+ };
+};
- qcom,ssbi@500000 {
- pmic@0 {
- keypad@148 {
- linux,keymap = <
- MATRIX_KEY(0, 0, KEY_MENU)
- MATRIX_KEY(0, 2, KEY_1)
- MATRIX_KEY(0, 3, KEY_4)
- MATRIX_KEY(0, 4, KEY_7)
- MATRIX_KEY(1, 0, KEY_UP)
- MATRIX_KEY(1, 1, KEY_LEFT)
- MATRIX_KEY(1, 2, KEY_DOWN)
- MATRIX_KEY(1, 3, KEY_5)
- MATRIX_KEY(1, 3, KEY_8)
- MATRIX_KEY(2, 0, KEY_HOME)
- MATRIX_KEY(2, 1, KEY_REPLY)
- MATRIX_KEY(2, 2, KEY_2)
- MATRIX_KEY(2, 3, KEY_6)
- MATRIX_KEY(3, 0, KEY_VOLUMEUP)
- MATRIX_KEY(3, 1, KEY_RIGHT)
- MATRIX_KEY(3, 2, KEY_3)
- MATRIX_KEY(3, 3, KEY_9)
- MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
- MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
- MATRIX_KEY(4, 1, KEY_BACK)
- MATRIX_KEY(4, 2, KEY_CAMERA)
- MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
- >;
- keypad,num-rows = <6>;
- keypad,num-columns = <5>;
- };
-
- gpio@150 {
- dragon_ethernet_gpios: ethernet-state {
- pinconf {
- pins = "gpio7";
- function = "normal";
- input-enable;
- bias-disable;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- dragon_bmp085_gpios: bmp085-state {
- pinconf {
- pins = "gpio16";
- function = "normal";
- input-enable;
- bias-disable;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- dragon_mpu3050_gpios: mpu3050-state {
- pinconf {
- pins = "gpio17";
- function = "normal";
- input-enable;
- bias-disable;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- dragon_sdcc3_gpios: sdcc3-state {
- pinconf {
- pins = "gpio22";
- function = "normal";
- input-enable;
- bias-disable;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- dragon_sdcc5_gpios: sdcc5-state {
- pinconf {
- pins = "gpio26";
- function = "normal";
- input-enable;
- bias-pull-up;
- qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- dragon_ak8975_gpios: ak8975-state {
- pinconf {
- pins = "gpio33";
- function = "normal";
- input-enable;
- bias-disable;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- dragon_cm3605_gpios: cm3605-state {
- /* Pin 34 connected to the proxy IRQ */
- gpio34-pins {
- pins = "gpio34";
- function = "normal";
- input-enable;
- bias-disable;
- power-source = <PM8058_GPIO_S3>;
- };
- /* Pin 35 connected to ASET */
- gpio35-pins {
- pins = "gpio35";
- function = "normal";
- output-high;
- bias-disable;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- dragon_veth_gpios: veth-state {
- pinconf {
- pins = "gpio40";
- function = "normal";
- bias-disable;
- drive-push-pull;
- };
- };
- };
-
- mpps@50 {
- dragon_cm3605_mpps: cm3605-mpps-state {
- mpp5 {
- pins = "mpp5";
- function = "analog";
- input-enable;
- bias-high-impedance;
- /* Let's use channel 5 */
- qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
- power-source = <PM8058_GPIO_S3>;
- };
- };
- };
-
- xoadc@197 {
- /* Reference voltage 2.2 V */
- xoadc-ref-supply = <&pm8058_l18>;
-
- /* Board-specific channels */
- mpp5@5 {
- /* Connected to AOUT of ALS sensor */
- reg = <0x00 0x05>;
- };
- mpp6@6 {
- /* Connected to test point TP43 */
- reg = <0x00 0x06>;
- };
- mpp7@7 {
- /* Connected to battery thermistor */
- reg = <0x00 0x07>;
- };
- mpp8@8 {
- /* Connected to battery ID detector */
- reg = <0x00 0x08>;
- };
- mpp9@9 {
- /* Connected to XO thermistor */
- reg = <0x00 0x09>;
- };
- };
-
- led@48 {
- /*
- * The keypad LED @0x48 is routed to
- * the sensor board where it is
- * connected to an infrared LED
- * SFH4650 (60mW, @850nm) next to the
- * ambient light and proximity sensor
- * Capella Microsystems CM3605.
- */
- compatible = "qcom,pm8058-keypad-led";
- reg = <0x48>;
- label = "pm8058:infrared:proximitysensor";
- default-state = "off";
- linux,default-trigger = "cm3605";
- };
- led@131 {
- compatible = "qcom,pm8058-led";
- reg = <0x131>;
- label = "pm8058:red";
- color = <LED_COLOR_ID_RED>;
- default-state = "off";
- };
- led@132 {
- /*
- * This is actually green too on my
- * board, but documented as yellow.
- */
- compatible = "qcom,pm8058-led";
- reg = <0x132>;
- label = "pm8058:yellow";
- color = <LED_COLOR_ID_YELLOW>;
- default-state = "off";
- linux,default-trigger = "mmc0";
- };
- led@133 {
- compatible = "qcom,pm8058-led";
- reg = <0x133>;
- label = "pm8058:green";
- function = LED_FUNCTION_HEARTBEAT;
- color = <LED_COLOR_ID_GREEN>;
- default-state = "on";
- linux,default-trigger = "heartbeat";
- };
- };
+&pm8058_gpio {
+ dragon_ethernet_gpios: ethernet-state {
+ pinconf {
+ pins = "gpio7";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_bmp085_gpios: bmp085-state {
+ pinconf {
+ pins = "gpio16";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_mpu3050_gpios: mpu3050-state {
+ pinconf {
+ pins = "gpio17";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_sdcc3_gpios: sdcc3-state {
+ pinconf {
+ pins = "gpio22";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_sdcc5_gpios: sdcc5-state {
+ pinconf {
+ pins = "gpio26";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_ak8975_gpios: ak8975-state {
+ pinconf {
+ pins = "gpio33";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_cm3605_gpios: cm3605-state {
+ /* Pin 34 connected to the proxy IRQ */
+ gpio34-pins {
+ pins = "gpio34";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ /* Pin 35 connected to ASET */
+ gpio35-pins {
+ pins = "gpio35";
+ function = "normal";
+ output-high;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_veth_gpios: veth-state {
+ pinconf {
+ pins = "gpio40";
+ function = "normal";
+ bias-disable;
+ drive-push-pull;
};
+ };
+};
- gsbi@16200000 {
- qcom,mode = <GSBI_PROT_I2C>;
- status = "okay";
+&pm8058_keypad {
+ linux,keymap = <
+ MATRIX_KEY(0, 0, KEY_MENU)
+ MATRIX_KEY(0, 2, KEY_1)
+ MATRIX_KEY(0, 3, KEY_4)
+ MATRIX_KEY(0, 4, KEY_7)
+ MATRIX_KEY(1, 0, KEY_UP)
+ MATRIX_KEY(1, 1, KEY_LEFT)
+ MATRIX_KEY(1, 2, KEY_DOWN)
+ MATRIX_KEY(1, 3, KEY_5)
+ MATRIX_KEY(1, 3, KEY_8)
+ MATRIX_KEY(2, 0, KEY_HOME)
+ MATRIX_KEY(2, 1, KEY_REPLY)
+ MATRIX_KEY(2, 2, KEY_2)
+ MATRIX_KEY(2, 3, KEY_6)
+ MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+ MATRIX_KEY(3, 1, KEY_RIGHT)
+ MATRIX_KEY(3, 2, KEY_3)
+ MATRIX_KEY(3, 3, KEY_9)
+ MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+ MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+ MATRIX_KEY(4, 1, KEY_BACK)
+ MATRIX_KEY(4, 2, KEY_CAMERA)
+ MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+ >;
+ keypad,num-rows = <6>;
+ keypad,num-columns = <5>;
+};
- gsbi3_i2c: i2c@16280000 {
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
- status = "okay";
-
- touchscreen@24 {
- compatible = "cypress,cy8ctma340";
- reg = <0x24>;
- /* Certainly we can do at least 400 kHz */
- clock-frequency = <400000>;
- /* IRQ on GPIO61 called /CTP_INT */
- interrupt-parent = <&tlmm>;
- interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
- /*
- * The I2C bus is using a PCA9306 level translator from L16A
- * to L2B so these two voltages are needed and L16A is
- * kind of the IO voltage, however L16Aisn't really fed to
- * the TMA340, which relies entirely on L2B (PM8901 L2).
- */
- vcpin-supply = <&pm8058_l16>;
- vdd-supply = <&pm8901_l2>;
- /* GPIO58, called WAKE_CTP */
- reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
- touchscreen-size-x = <480>;
- touchscreen-size-y = <800>;
- active-interval-ms = <0>;
- touch-timeout-ms = <255>;
- lowpower-interval-ms = <10>;
- bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_tma340_gpios>;
- };
- };
+&pm8058_led48 {
+ /*
+ * The keypad LED @0x48 is routed to
+ * the sensor board where it is
+ * connected to an infrared LED
+ * SFH4650 (60mW, @850nm) next to the
+ * ambient light and proximity sensor
+ * Capella Microsystems CM3605.
+ */
+ label = "pm8058:infrared:proximitysensor";
+ default-state = "off";
+ linux,default-trigger = "cm3605";
+ status = "okay";
+};
+
+&pm8058_led131 {
+ label = "pm8058:red";
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ status = "okay";
+};
+
+&pm8058_led132 {
+ /*
+ * This is actually green too on my
+ * board, but documented as yellow.
+ */
+ label = "pm8058:yellow";
+ color = <LED_COLOR_ID_YELLOW>;
+ default-state = "off";
+ linux,default-trigger = "mmc0";
+ status = "okay";
+};
+
+&pm8058_led133 {
+ label = "pm8058:green";
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ status = "okay";
+};
+
+&pm8058_mpps {
+ dragon_cm3605_mpps: cm3605-mpps-state {
+ mpp5 {
+ pins = "mpp5";
+ function = "analog";
+ input-enable;
+ bias-high-impedance;
+ /* Let's use channel 5 */
+ qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+ power-source = <PM8058_GPIO_S3>;
};
+ };
+};
- gsbi@19800000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
+&rpm {
+ /*
+ * Set up of the PMIC RPM regulators for this board
+ * PM8901 supplies "preliminary regulators" whatever
+ * that means
+ */
+ pm8901-regulators {
+ vdd_l0-supply = <&pm8901_s4>;
+ vdd_l1-supply = <&vph>;
+ vdd_l2-supply = <&vph>;
+ vdd_l3-supply = <&vph>;
+ vdd_l4-supply = <&vph>;
+ vdd_l5-supply = <&vph>;
+ vdd_l6-supply = <&vph>;
+ /* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ lvs0_in-supply = <&pm8058_s3>;
+ lvs1_in-supply = <&pm8901_s4>;
+ lvs2_in-supply = <&pm8058_l0>;
+ lvs3_in-supply = <&pm8058_s2>;
+ mvs_in-supply = <&pm8058_s3>;
+
+ l0 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l2 {
+ /* TMA340 requires strictly 3.3V */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l4 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l5 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l6 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ bias-pull-down;
+ };
- i2c@19880000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
-
- eeprom@52 {
- /* A 16KiB Platform ID EEPROM on the CPU carrier board */
- compatible = "atmel,24c128";
- reg = <0x52>;
- vcc-supply = <&pm8058_s3>;
- pagesize = <64>;
- };
- wm8903: wm8903@1a {
- /* This Woolfson Micro device has an unrouted interrupt line */
- compatible = "wlf,wm8903";
- reg = <0x1a>;
-
- AVDD-supply = <&pm8058_l16>;
- CPVDD-supply = <&pm8058_l16>;
- DBVDD-supply = <&pm8058_s3>;
- DCVDD-supply = <&pm8058_l0>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- micdet-cfg = <0>;
- micdet-delay = <100>;
- gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
- };
- };
+ /* s0 and s1 are SAW regulators controlled over SPM */
+ s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
};
- gsbi@19c00000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
+ /* LVS0 thru 3 and mvs are just switches */
+ lvs0 {
+ regulator-always-on;
+ };
+ lvs1 { };
+ lvs2 { };
+ lvs3 { };
+ mvs { };
- serial@19c40000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_gsbi12_serial_pins>;
- };
+ };
- i2c@19c80000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
-
- ak8975@c {
- compatible = "asahi-kasei,ak8975";
- reg = <0x0c>;
- interrupt-parent = <&pm8058_gpio>;
- interrupts = <33 IRQ_TYPE_EDGE_RISING>;
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_ak8975_gpios>;
- vid-supply = <&pm8058_lvs0>; // 1.8V
- vdd-supply = <&pm8058_l14>; // 2.85V
- };
- bmp085@77 {
- compatible = "bosch,bmp085";
- reg = <0x77>;
- interrupt-parent = <&pm8058_gpio>;
- interrupts = <16 IRQ_TYPE_EDGE_RISING>;
- reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_bmp085_gpios>;
- vddd-supply = <&pm8058_lvs0>; // 1.8V
- vdda-supply = <&pm8058_l14>; // 2.85V
- };
- mpu3050@68 {
- compatible = "invensense,mpu3050";
- reg = <0x68>;
- /*
- * GPIO17 is pulled high by a 10k
- * resistor to VLOGIC so needs to be
- * active low/falling edge.
- */
- interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_mpu3050_gpios>;
- vlogic-supply = <&pm8058_lvs0>; // 1.8V
- vdd-supply = <&pm8058_l14>; // 2.85V
-
- /*
- * The MPU-3050 acts as a hub for the
- * accelerometer.
- */
- i2c-gate {
- #address-cells = <1>;
- #size-cells = <0>;
-
- kxsd9@18 {
- compatible = "kionix,kxsd9";
- reg = <0x18>;
- interrupt-parent = <&tlmm>;
- interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_kxsd9_gpios>;
- iovdd-supply = <&pm8058_lvs0>; // 1.8V
- vdd-supply = <&pm8058_l14>; // 2.85V
- };
- };
- };
- };
+ pm8058-regulators {
+ vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+ vdd_l2_l11_l12-supply = <&vph>;
+ vdd_l3_l4_l5-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l8-supply = <&vph>;
+ vdd_l9-supply = <&vph>;
+ vdd_l10-supply = <&vph>;
+ vdd_l13_l16-supply = <&pm8058_s4>;
+ vdd_l14_l15-supply = <&vph>;
+ vdd_l17_l18-supply = <&vph>;
+ vdd_l19_l20-supply = <&vph>;
+ vdd_l21-supply = <&pm8058_s3>;
+ vdd_l22-supply = <&pm8058_s3>;
+ vdd_l23_l24_l25-supply = <&pm8058_s3>;
+ vdd_s0-supply = <&vph>;
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_ncp-supply = <&vph>;
+
+ l0 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l4 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l5 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l6 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3600000>;
+ bias-pull-down;
+ };
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l8 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <3050000>;
+ bias-pull-down;
+ };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l10 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l11 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ bias-pull-down;
+ };
+ l12 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ bias-pull-down;
+ };
+ l13 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ bias-pull-down;
+ };
+ l14 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+ l15 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+ l17 {
+ // 1.5V according to schematic
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l18 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ bias-pull-down;
+ };
+ l19 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ bias-pull-down;
+ };
+ l20 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l21 {
+ // 1.1 V according to schematic
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+ l22 {
+ // 1.2 V according to schematic
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ bias-pull-down;
+ };
+ l23 {
+ // Unused
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l24 {
+ // Unused
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l25 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
};
- external-bus@1a100000 {
- /* The EBI2 will instantiate first, then populate its children */
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_ebi2_pins>;
-
- /*
- * An on-board SMSC LAN9221 chip for "debug ethernet",
- * which is actually just an ordinary ethernet on the
- * EBI2. This has a 25MHz chrystal next to it, so no
- * clocking is needed.
- */
- ethernet@2,0 {
- compatible = "smsc,lan9221", "smsc,lan9115";
- reg = <2 0x0 0x100>;
- /*
- * The second interrupt is the PME interrupt
- * for network wakeup, connected to the TLMM.
- */
- interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
- <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
- reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
- vdd33a-supply = <&dragon_veth>;
- vddvario-supply = <&dragon_vario>;
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_ethernet_gpios>;
- phy-mode = "mii";
- reg-io-width = <2>;
- smsc,force-external-phy;
- smsc,irq-push-pull;
-
- /*
- * SLOW chipselect config
- * Delay 9 cycles (140ns@64MHz) between SMSC
- * LAN9221 Ethernet controller reads and writes
- * on CS2.
- */
- qcom,xmem-recovery-cycles = <0>;
- qcom,xmem-write-hold-cycles = <3>;
- qcom,xmem-write-delta-cycles = <31>;
- qcom,xmem-read-delta-cycles = <28>;
- qcom,xmem-write-wait-cycles = <9>;
- qcom,xmem-read-wait-cycles = <9>;
- };
+ s0 {
+ // regulator-min-microvolt = <500000>;
+ // regulator-max-microvolt = <1325000>;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s1 {
+ // regulator-min-microvolt = <500000>;
+ // regulator-max-microvolt = <1250000>;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s2 {
+ // 1.3 V according to schematic
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ regulator-always-on;
+ bias-pull-down;
+ };
+ s4 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ qcom,switch-mode-frequency = <1600000>;
+ regulator-always-on;
+ bias-pull-down;
};
- rpm@104000 {
- /*
- * Set up of the PMIC RPM regulators for this board
- * PM8901 supplies "preliminary regulators" whatever
- * that means
- */
- pm8901-regulators {
- vdd_l0-supply = <&pm8901_s4>;
- vdd_l1-supply = <&vph>;
- vdd_l2-supply = <&vph>;
- vdd_l3-supply = <&vph>;
- vdd_l4-supply = <&vph>;
- vdd_l5-supply = <&vph>;
- vdd_l6-supply = <&vph>;
- /* vdd_s0-supply, vdd_s1-supply: SAW regulators */
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- lvs0_in-supply = <&pm8058_s3>;
- lvs1_in-supply = <&pm8901_s4>;
- lvs2_in-supply = <&pm8058_l0>;
- lvs3_in-supply = <&pm8058_s2>;
- mvs_in-supply = <&pm8058_s3>;
-
- l0 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- bias-pull-down;
- };
- l1 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
- l2 {
- /* TMA340 requires strictly 3.3V */
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
- l3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
- l4 {
- regulator-min-microvolt = <2600000>;
- regulator-max-microvolt = <2600000>;
- bias-pull-down;
- };
- l5 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- bias-pull-down;
- };
- l6 {
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- bias-pull-down;
- };
-
- /* s0 and s1 are SAW regulators controlled over SPM */
- s2 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- };
- s3 {
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- };
- s4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- };
-
- /* LVS0 thru 3 and mvs are just switches */
- lvs0 {
- regulator-always-on;
- };
- lvs1 { };
- lvs2 { };
- lvs3 { };
- mvs { };
+ /* LVS0 and LVS1 are just switches */
+ lvs0 {
+ bias-pull-down;
+ };
+ lvs1 {
+ bias-pull-down;
+ };
- };
+ ncp {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ };
+ };
+};
- pm8058-regulators {
- vdd_l0_l1_lvs-supply = <&pm8058_s3>;
- vdd_l2_l11_l12-supply = <&vph>;
- vdd_l3_l4_l5-supply = <&vph>;
- vdd_l6_l7-supply = <&vph>;
- vdd_l8-supply = <&vph>;
- vdd_l9-supply = <&vph>;
- vdd_l10-supply = <&vph>;
- vdd_l13_l16-supply = <&pm8058_s4>;
- vdd_l14_l15-supply = <&vph>;
- vdd_l17_l18-supply = <&vph>;
- vdd_l19_l20-supply = <&vph>;
- vdd_l21-supply = <&pm8058_s3>;
- vdd_l22-supply = <&pm8058_s3>;
- vdd_l23_l24_l25-supply = <&pm8058_s3>;
- vdd_s0-supply = <&vph>;
- vdd_s1-supply = <&vph>;
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- vdd_ncp-supply = <&vph>;
-
- l0 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- bias-pull-down;
- };
- l1 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- bias-pull-down;
- };
- l2 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2600000>;
- bias-pull-down;
- };
- l3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
- l4 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- bias-pull-down;
- };
- l5 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- bias-pull-down;
- };
- l6 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3600000>;
- bias-pull-down;
- };
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <3050000>;
- bias-pull-down;
- };
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
- l10 {
- regulator-min-microvolt = <2600000>;
- regulator-max-microvolt = <2600000>;
- bias-pull-down;
- };
- l11 {
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- bias-pull-down;
- };
- l12 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- bias-pull-down;
- };
- l13 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- bias-pull-down;
- };
- l14 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
- l15 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- bias-pull-down;
- };
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- regulator-always-on;
- };
- l17 {
- // 1.5V according to schematic
- regulator-min-microvolt = <2600000>;
- regulator-max-microvolt = <2600000>;
- bias-pull-down;
- };
- l18 {
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- bias-pull-down;
- };
- l19 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- bias-pull-down;
- };
- l20 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
- l21 {
- // 1.1 V according to schematic
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- bias-pull-down;
- regulator-always-on;
- };
- l22 {
- // 1.2 V according to schematic
- regulator-min-microvolt = <1150000>;
- regulator-max-microvolt = <1150000>;
- bias-pull-down;
- };
- l23 {
- // Unused
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- bias-pull-down;
- };
- l24 {
- // Unused
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- bias-pull-down;
- };
- l25 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- bias-pull-down;
- };
-
- s0 {
- // regulator-min-microvolt = <500000>;
- // regulator-max-microvolt = <1325000>;
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- };
- s1 {
- // regulator-min-microvolt = <500000>;
- // regulator-max-microvolt = <1250000>;
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- };
- s2 {
- // 1.3 V according to schematic
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1400000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- };
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <1600000>;
- regulator-always-on;
- bias-pull-down;
- };
- s4 {
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- qcom,switch-mode-frequency = <1600000>;
- regulator-always-on;
- bias-pull-down;
- };
-
- /* LVS0 and LVS1 are just switches */
- lvs0 {
- bias-pull-down;
- };
- lvs1 {
- bias-pull-down;
- };
-
- ncp {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <1600000>;
- };
- };
+/* Internal 3.69 GiB eMMC */
+&sdcc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc1_pins>;
+ vmmc-supply = <&pm8901_l5>;
+ vqmmc-supply = <&pm8901_lvs0>;
+ status = "okay";
+};
+
+/* External micro SD card, directly connected, pulled up to 2.85 V */
+&sdcc3 {
+ /* Enable SSBI GPIO 22 as input, use for card detect */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+ cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&pm8058_l14>;
+ status = "okay";
+};
+
+/*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+&sdcc5 {
+ /* Enable SSBI GPIO 26 as input, use for card detect */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+ cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&pm8058_l14>;
+ vqmmc-supply = <&dragon_vio_txb>;
+ status = "okay";
+};
+
+&tlmm {
+ /* eMMC pins, all 8 data lines connected */
+ dragon_sdcc1_pins: sdcc1-state {
+ clk-pins {
+ pins = "gpio167"; /* SDC1 CLK */
+ function = "sdc1";
+ drive-strength = <16>;
+ bias-disable;
};
- amba {
- /* Internal 3.69 GiB eMMC */
- mmc@12400000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_sdcc1_pins>;
- vmmc-supply = <&pm8901_l5>;
- vqmmc-supply = <&pm8901_lvs0>;
- };
+ cmd-pins {
+ pins = "gpio168"; /* SDC1 CMD */
+ function = "sdc1";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ data-pins {
+ /* SDC1 D0 to D7 */
+ pins = "gpio159", "gpio160", "gpio161", "gpio162",
+ "gpio163", "gpio164", "gpio165", "gpio166";
+ function = "sdc1";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
- /* External micro SD card, directly connected, pulled up to 2.85 V */
- mmc@12180000 {
- status = "okay";
- /* Enable SSBI GPIO 22 as input, use for card detect */
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
- cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
- wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
- vmmc-supply = <&pm8058_l14>;
- };
+ /*
+ * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+ * configuration.
+ */
+ dragon_sdcc3_pins: sdcc3-state {
+ clk-pins {
+ pins = "sdc3_clk";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ cmd-pins {
+ pins = "sdc3_cmd";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ data-pins {
+ pins = "sdc3_data";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
- /*
- * Second external micro SD card, using two TXB104RGYR levelshifters
- * to lift from 1.8 V to 2.85 V
- */
- mmc@12200000 {
- status = "okay";
- /* Enable SSBI GPIO 26 as input, use for card detect */
- pinctrl-names = "default";
- pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
- cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
- wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
- vmmc-supply = <&pm8058_l14>;
- vqmmc-supply = <&dragon_vio_txb>;
- };
+ /* Second SD card slot pins */
+ dragon_sdcc5_pins: sdcc5-state {
+ clk-pins {
+ pins = "gpio97"; /* SDC5 CLK */
+ function = "sdc5";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ cmd-pins {
+ pins = "gpio95"; /* SDC5 CMD */
+ function = "sdc5";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ data-pins {
+ /* SDC5 D0 to D3 */
+ pins = "gpio96", "gpio98", "gpio99", "gpio100";
+ function = "sdc5";
+ drive-strength = <10>;
+ bias-pull-up;
};
};
+
+ dragon_gsbi3_i2c_pins: gsbi3-i2c-state {
+ pins = "gpio43", "gpio44";
+ function = "gsbi3";
+ drive-strength = <8>;
+ /* These have external pull-up 2.2kOhm to 1.8V */
+ bias-disable;
+ };
+
+ dragon_gsbi8_i2c_pins: gsbi8-i2c-state {
+ pins = "gpio64", "gpio65";
+ function = "gsbi8";
+ drive-strength = <16>;
+ /* These have external pull-up 2.2kOhm to 1.8V */
+ bias-disable;
+ };
+
+ dragon_gsbi12_i2c_pins: gsbi12-i2c-state {
+ pins = "gpio115", "gpio116";
+ function = "gsbi12";
+ drive-strength = <16>;
+ /* These have external pull-up 4.7kOhm to 1.8V */
+ bias-disable;
+ };
+
+ /* Primary serial port uart 0 pins */
+ dragon_gsbi12_serial_pins: gsbi12-serial-state {
+ tx-pins {
+ pins = "gpio117";
+ function = "gsbi12";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ rx-pins {
+ pins = "gpio118";
+ function = "gsbi12";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ dragon_ebi2_pins: ebi2-state {
+ /*
+ * Pins used by EBI2 on the Dragonboard, actually only
+ * CS2 is used by a real peripheral. CS0 is just
+ * routed to a test point.
+ */
+ mux0-pins {
+ pins =
+ /* "gpio39", CS1A_N this is not good to mux */
+ "gpio40", /* CS2A_N */
+ "gpio134"; /* CS0_N testpoint TP29 */
+ function = "ebi2cs";
+ };
+ mux1-pins {
+ pins =
+ /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
+ "gpio123", "gpio124", "gpio125", "gpio126",
+ "gpio127", "gpio128", "gpio129", "gpio130",
+ /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
+ "gpio135", "gpio136", "gpio137", "gpio138",
+ "gpio139", "gpio140", "gpio141", "gpio142",
+ "gpio143", "gpio144", "gpio145", "gpio146",
+ "gpio147", "gpio148", "gpio149", "gpio150",
+ "gpio151", /* EBI2_OE_N */
+ "gpio153", /* EBI2_ADV */
+ "gpio157"; /* EBI2_WE_N */
+ function = "ebi2";
+ };
+ };
+
+ /* Interrupt line for the KXSD9 accelerometer */
+ dragon_kxsd9_gpios: kxsd9-state {
+ pins = "gpio57"; /* IRQ line */
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ dragon_tma340_gpios: tma340-state {
+ reset-pins {
+ /* RESET line, TS_ATTN, WAKE_CTP */
+ pins = "gpio58";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-disable;
+ };
+ irq-pins {
+ pins = "gpio61"; /* IRQ line */
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&xoadc {
+ /* Reference voltage 2.2 V */
+ xoadc-ref-supply = <&pm8058_l18>;
+
+ /* Board-specific channels */
+ mpp5@5 {
+ /* Connected to AOUT of ALS sensor */
+ reg = <0x00 0x05>;
+ };
+ mpp6@6 {
+ /* Connected to test point TP43 */
+ reg = <0x00 0x06>;
+ };
+ mpp7@7 {
+ /* Connected to battery thermistor */
+ reg = <0x00 0x07>;
+ };
+ mpp8@8 {
+ /* Connected to battery ID detector */
+ reg = <0x00 0x08>;
+ };
+ mpp9@9 {
+ /* Connected to XO thermistor */
+ reg = <0x00 0x09>;
+ };
};
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-26 14:42:54 +0300