1 files changed, 89 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml b/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
new file mode 100644
index 000000000000..5dd209206e88
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-peripheral-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Peripheral-specific properties for a SPI bus.
+
+description:
+  Many SPI controllers need to add properties to peripheral devices. They could
+  be common properties like spi-max-frequency, spi-cpha, etc. or they could be
+  controller specific like delay in clock or data lines, etc. These properties
+  need to be defined in the peripheral node because they are per-peripheral and
+  there can be multiple peripherals attached to a controller. All those
+  properties are listed here. The controller specific properties should go in
+  their own separate schema that should be referenced from here.
+
+maintainers:
+  - Pratyush Yadav <p.yadav@ti.com>
+
+properties:
+  reg:
+    minItems: 1
+    maxItems: 256
+    items:
+      minimum: 0
+      maximum: 256
+    description:
+      Chip select used by the device.
+
+  spi-3wire:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires 3-wire mode.
+
+  spi-cpha:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires shifted clock phase (CPHA) mode.
+
+  spi-cpol:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires inverse clock polarity (CPOL) mode.
+
+  spi-cs-high:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires the chip select active high.
+
+  spi-lsb-first:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires the LSB first mode.
+
+  spi-max-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Maximum SPI clocking speed of the device in Hz.
+
+  spi-rx-bus-width:
+    description:
+      Bus width to the SPI bus used for read transfers.
+      If 0 is provided, then no RX will be possible on this device.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 4, 8]
+    default: 1
+
+  spi-rx-delay-us:
+    description:
+      Delay, in microseconds, after a read transfer.
+
+  spi-tx-bus-width:
+    description:
+      Bus width to the SPI bus used for write transfers.
+      If 0 is provided, then no TX will be possible on this device.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 4, 8]
+    default: 1
+
+  spi-tx-delay-us:
+    description:
+      Delay, in microseconds, after a write transfer.
+
+# The controller specific properties go here.
+allOf:
+  - $ref: cdns,qspi-nor-peripheral-props.yaml#
+
+additionalProperties: true