diff options
44 files changed, 2606 insertions, 419 deletions
diff --git a/Documentation/devicetree/bindings/input/goodix,gt7375p.yaml b/Documentation/devicetree/bindings/input/goodix,gt7375p.yaml new file mode 100644 index 000000000000..fe1c5016f7f3 --- /dev/null +++ b/Documentation/devicetree/bindings/input/goodix,gt7375p.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/goodix,gt7375p.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Goodix GT7375P touchscreen + +maintainers: + - Douglas Anderson <dianders@chromium.org> + +description: + Supports the Goodix GT7375P touchscreen. + This touchscreen uses the i2c-hid protocol but has some non-standard + power sequencing required. + +properties: + compatible: + items: + - const: goodix,gt7375p + + reg: + enum: + - 0x5d + - 0x14 + + interrupts: + maxItems: 1 + + reset-gpios: + true + + vdd-supply: + description: The 3.3V supply to the touchscreen. + +required: + - compatible + - reg + - interrupts + - reset-gpios + - vdd-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ap_ts: touchscreen@5d { + compatible = "goodix,gt7375p"; + reg = <0x5d>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; + vdd-supply = <&pp3300_ts>; + }; + }; diff --git a/Documentation/hid/amd-sfh-hid.rst b/Documentation/hid/amd-sfh-hid.rst index 1f2fe29ccd4f..19ae94cde3b4 100644 --- a/Documentation/hid/amd-sfh-hid.rst +++ b/Documentation/hid/amd-sfh-hid.rst @@ -3,13 +3,13 @@ AMD Sensor Fusion Hub ===================== -AMD Sensor Fusion Hub (SFH) is part of an SOC starting from Ryzen based platforms. +AMD Sensor Fusion Hub (SFH) is part of an SOC starting from Ryzen-based platforms. The solution is working well on several OEM products. AMD SFH uses HID over PCIe bus. In terms of architecture it resembles ISH, however the major difference is all the HID reports are generated as part of the kernel driver. -1. Block Diagram -================ +Block Diagram +------------- :: @@ -45,20 +45,20 @@ the HID reports are generated as part of the kernel driver. AMD HID Transport Layer ----------------------- AMD SFH transport is also implemented as a bus. Each client application executing in the AMD MP2 is -registered as a device on this bus. Here: MP2 which is an ARM core connected to x86 for processing +registered as a device on this bus. Here, MP2 is an ARM core connected to x86 for processing sensor data. The layer, which binds each device (AMD SFH HID driver) identifies the device type and -registers with the hid core. Transport layer attach a constant "struct hid_ll_driver" object with +registers with the HID core. Transport layer attaches a constant "struct hid_ll_driver" object with each device. Once a device is registered with HID core, the callbacks provided via this struct are used by HID core to communicate with the device. AMD HID Transport layer implements the synchronous calls. AMD HID Client Layer -------------------- -This layer is responsible to implement HID request and descriptors. As firmware is OS agnostic, HID +This layer is responsible to implement HID requests and descriptors. As firmware is OS agnostic, HID client layer fills the HID request structure and descriptors. HID client layer is complex as it is -interface between MP2 PCIe layer and HID. HID client layer initialized the MP2 PCIe layer and holds -the instance of MP2 layer. It identifies the number of sensors connected using MP2-PCIe layer. Base -on that allocates the DRAM address for each and every sensor and pass it to MP2-PCIe driver.On -enumeration of each the sensor, client layer fills the HID Descriptor structure and HID input repor +interface between MP2 PCIe layer and HID. HID client layer initializes the MP2 PCIe layer and holds +the instance of MP2 layer. It identifies the number of sensors connected using MP2-PCIe layer. Based +on that allocates the DRAM address for each and every sensor and passes it to MP2-PCIe driver. On +enumeration of each sensor, client layer fills the HID Descriptor structure and HID input report structure. HID Feature report structure is optional. The report descriptor structure varies from sensor to sensor. @@ -72,7 +72,7 @@ The communication between X86 and MP2 is split into three parts. 2. Data transfer via DRAM. 3. Supported sensor info via P2C registers. -Commands are sent to MP2 using C2P Mailbox registers. Writing into C2P Message registers generate +Commands are sent to MP2 using C2P Mailbox registers. Writing into C2P Message registers generates interrupt to MP2. The client layer allocates the physical memory and the same is sent to MP2 via the PCI layer. MP2 firmware writes the command output to the access DRAM memory which the client layer has allocated. Firmware always writes minimum of 32 bytes into DRAM. So as a protocol driver diff --git a/Documentation/hid/hid-alps.rst b/Documentation/hid/hid-alps.rst index e2f4c4c11e3f..767c96bcbb7c 100644 --- a/Documentation/hid/hid-alps.rst +++ b/Documentation/hid/hid-alps.rst @@ -64,7 +64,7 @@ Case2 ReportID_3 TP Absolute Command Read/Write ------------------ -To read/write to RAM, need to send a commands to the device. +To read/write to RAM, need to send a command to the device. The command format is as below. @@ -80,7 +80,7 @@ Byte6 Value Byte Byte7 Checksum ===== ====================== -Command Byte is read=0xD1/write=0xD2 . +Command Byte is read=0xD1/write=0xD2. Address is read/write RAM address. diff --git a/Documentation/hid/hid-sensor.rst b/Documentation/hid/hid-sensor.rst index 758972e34971..c1c9b8d8dca6 100644 --- a/Documentation/hid/hid-sensor.rst +++ b/Documentation/hid/hid-sensor.rst @@ -48,12 +48,12 @@ for different sensors. For example an accelerometer can send X,Y and Z data, whe an ambient light sensor can send illumination data. So the implementation has two parts: -- Core hid driver +- Core HID driver - Individual sensor processing part (sensor drivers) Core driver ----------- -The core driver registers (hid-sensor-hub) registers as a HID driver. It parses +The core driver (hid-sensor-hub) registers as a HID driver. It parses report descriptors and identifies all the sensors present. It adds an MFD device with name HID-SENSOR-xxxx (where xxxx is usage id from the specification). @@ -95,14 +95,14 @@ Registration functions:: u32 usage_id, struct hid_sensor_hub_callbacks *usage_callback): -Registers callbacks for an usage id. The callback functions are not allowed +Registers callbacks for a usage id. The callback functions are not allowed to sleep:: int sensor_hub_remove_callback(struct hid_sensor_hub_device *hsdev, u32 usage_id): -Removes callbacks for an usage id. +Removes callbacks for a usage id. Parsing function:: @@ -166,7 +166,7 @@ This allows some differentiating use cases, where vendor can provide application Some common use cases are debug other sensors or to provide some events like keyboard attached/detached or lid open/close. -To allow application to utilize these sensors, here they are exported uses sysfs +To allow application to utilize these sensors, here they are exported using sysfs attribute groups, attributes and misc device interface. An example of this representation on sysfs:: @@ -207,9 +207,9 @@ An example of this representation on sysfs:: │ │ │ ├── input-1-200202-units │ │ │ ├── input-1-200202-value -Here there is a custom sensors with four fields, two feature and two inputs. +Here there is a custom sensor with four fields: two feature and two inputs. Each field is represented by a set of attributes. All fields except the "value" -are read only. The value field is a RW field. +are read only. The value field is a read-write field. Example:: @@ -237,6 +237,6 @@ These reports are pushed using misc device interface in a FIFO order:: │ │ │ ├── 10:53 -> ../HID-SENSOR-2000e1.6.auto │ ├── HID-SENSOR-2000e1.6.auto -Each reports can be of variable length preceded by a header. This header -consist of a 32 bit usage id, 64 bit time stamp and 32 bit length field of raw +Each report can be of variable length preceded by a header. This header +consists of a 32-bit usage id, 64-bit time stamp and 32-bit length field of raw data. diff --git a/Documentation/hid/hid-transport.rst b/Documentation/hid/hid-transport.rst index 0fe526f36db6..6f1692da296c 100644 --- a/Documentation/hid/hid-transport.rst +++ b/Documentation/hid/hid-transport.rst @@ -12,8 +12,8 @@ Bluetooth, I2C and user-space I/O drivers. The HID subsystem is designed as a bus. Any I/O subsystem may provide HID devices and register them with the HID bus. HID core then loads generic device -drivers on top of it. The transport drivers are responsible of raw data -transport and device setup/management. HID core is responsible of +drivers on top of it. The transport drivers are responsible for raw data +transport and device setup/management. HID core is responsible for report-parsing, report interpretation and the user-space API. Device specifics and quirks are handled by all layers depending on the quirk. @@ -67,7 +67,7 @@ Transport drivers attach a constant "struct hid_ll_driver" object with each device. Once a device is registered with HID core, the callbacks provided via this struct are used by HID core to communicate with the device. -Transport drivers are responsible of detecting device failures and unplugging. +Transport drivers are responsible for detecting device failures and unplugging. HID core will operate a device as long as it is registered regardless of any device failures. Once transport drivers detect unplug or failure events, they must unregister the device from HID core and HID core will stop using the @@ -101,7 +101,7 @@ properties in common. channel. Any unrequested incoming or outgoing data report must be sent on this channel and is never acknowledged by the remote side. Devices usually send their input events on this channel. Outgoing events are normally - not send via intr, except if high throughput is required. + not sent via intr, except if high throughput is required. - Control Channel (ctrl): The ctrl channel is used for synchronous requests and device management. Unrequested data input events must not be sent on this channel and are normally ignored. Instead, devices only send management @@ -161,7 +161,7 @@ allowed on the intr channel and are the only means of data there. payload may be blocked by the underlying transport driver if the specification does not allow them. - SET_REPORT: A SET_REPORT request has a report ID plus data as payload. It is - sent from host to device and a device must update it's current report state + sent from host to device and a device must update its current report state according to the given data. Any of the 3 report types can be used. However, INPUT reports as payload might be blocked by the underlying transport driver if the specification does not allow them. @@ -294,7 +294,7 @@ The available HID callbacks are: void (*request) (struct hid_device *hdev, struct hid_report *report, int reqtype) - Send an HID request on the ctrl channel. "report" contains the report that + Send a HID request on the ctrl channel. "report" contains the report that should be sent and "reqtype" the request type. Request-type can be HID_REQ_SET_REPORT or HID_REQ_GET_REPORT. diff --git a/Documentation/hid/hiddev.rst b/Documentation/hid/hiddev.rst index 9b28a97c03e6..caebc6266603 100644 --- a/Documentation/hid/hiddev.rst +++ b/Documentation/hid/hiddev.rst @@ -27,7 +27,7 @@ the following:: --> hiddev.c ----> POWER / MONITOR CONTROL In addition, other subsystems (apart from USB) can potentially feed -events into the input subsystem, but these have no effect on the hid +events into the input subsystem, but these have no effect on the HID device interface. Using the HID Device Interface @@ -73,7 +73,7 @@ The hiddev API uses a read() interface, and a set of ioctl() calls. HID devices exchange data with the host computer using data bundles called "reports". Each report is divided into "fields", each of which can have one or more "usages". In the hid-core, -each one of these usages has a single signed 32 bit value. +each one of these usages has a single signed 32-bit value. read(): ------- @@ -113,7 +113,7 @@ HIDIOCAPPLICATION - (none) This ioctl call returns the HID application usage associated with the -hid device. The third argument to ioctl() specifies which application +HID device. The third argument to ioctl() specifies which application index to get. This is useful when the device has more than one application collection. If the index is invalid (greater or equal to the number of application collections this device has) the ioctl @@ -181,7 +181,7 @@ looked up by type (input, output or feature) and id, so these fields must be filled in by the user. The ID can be absolute -- the actual report id as reported by the device -- or relative -- HID_REPORT_ID_FIRST for the first report, and (HID_REPORT_ID_NEXT | -report_id) for the next report after report_id. Without a-priori +report_id) for the next report after report_id. Without a priori information about report ids, the right way to use this ioctl is to use the relative IDs above to enumerate the valid IDs. The ioctl returns non-zero when there is no more next ID. The real report ID is @@ -200,7 +200,7 @@ HIDIOCGUCODE - struct hiddev_usage_ref (read/write) Returns the usage_code in a hiddev_usage_ref structure, given that -given its report type, report id, field index, and index within the +its report type, report id, field index, and index within the field have already been filled into the structure. HIDIOCGUSAGE diff --git a/Documentation/hid/hidraw.rst b/Documentation/hid/hidraw.rst index f41c1f0f6252..b717ee5cdaef 100644 --- a/Documentation/hid/hidraw.rst +++ b/Documentation/hid/hidraw.rst @@ -21,7 +21,7 @@ Hidraw is the only alternative, short of writing a custom kernel driver, for these non-conformant devices. A benefit of hidraw is that its use by userspace applications is independent -of the underlying hardware type. Currently, Hidraw is implemented for USB +of the underlying hardware type. Currently, hidraw is implemented for USB and Bluetooth. In the future, as new hardware bus types are developed which use the HID specification, hidraw will be expanded to add support for these new bus types. @@ -31,9 +31,10 @@ create hidraw device nodes. Udev will typically create the device nodes directly under /dev (eg: /dev/hidraw0). As this location is distribution- and udev rule-dependent, applications should use libudev to locate hidraw devices attached to the system. There is a tutorial on libudev with a -working example at: +working example at:: http://www.signal11.us/oss/udev/ + https://web.archive.org/web/2019*/www.signal11.us The HIDRAW API --------------- diff --git a/Documentation/hid/intel-ish-hid.rst b/Documentation/hid/intel-ish-hid.rst index d4785cf6eefd..f6ce44ff611d 100644 --- a/Documentation/hid/intel-ish-hid.rst +++ b/Documentation/hid/intel-ish-hid.rst @@ -4,19 +4,19 @@ Intel Integrated Sensor Hub (ISH) A sensor hub enables the ability to offload sensor polling and algorithm processing to a dedicated low power co-processor. This allows the core -processor to go into low power modes more often, resulting in the increased +processor to go into low power modes more often, resulting in increased battery life. -There are many vendors providing external sensor hubs confirming to HID -Sensor usage tables, and used in several tablets, 2 in 1 convertible laptops -and embedded products. Linux had this support since Linux 3.9. +There are many vendors providing external sensor hubs conforming to HID +Sensor usage tables. These may be found in tablets, 2-in-1 convertible laptops +and embedded products. Linux has had this support since Linux 3.9. Intel® introduced integrated sensor hubs as a part of the SoC starting from Cherry Trail and now supported on multiple generations of CPU packages. There are many commercial devices already shipped with Integrated Sensor Hubs (ISH). -These ISH also comply to HID sensor specification, but the difference is the +These ISH also comply to HID sensor specification, but the difference is the transport protocol used for communication. The current external sensor hubs -mainly use HID over i2C or USB. But ISH doesn't use either i2c or USB. +mainly use HID over I2C or USB. But ISH doesn't use either I2C or USB. 1. Overview =========== @@ -35,7 +35,7 @@ for a very high speed communication:: ----------------- ---------------------- PCI PCI ----------------- ---------------------- - |Host controller| --> | ISH processor | + |Host controller| --> | ISH processor | ----------------- ---------------------- USB Link ----------------- ---------------------- @@ -50,13 +50,13 @@ applications implemented in the firmware. The ISH allows multiple sensor management applications executing in the firmware. Like USB endpoints the messaging can be to/from a client. As part of enumeration process, these clients are identified. These clients can be simple -HID sensor applications, sensor calibration application or senor firmware -update application. +HID sensor applications, sensor calibration applications or sensor firmware +update applications. The implementation model is similar, like USB bus, ISH transport is also implemented as a bus. Each client application executing in the ISH processor is registered as a device on this bus. The driver, which binds each device -(ISH HID driver) identifies the device type and registers with the hid core. +(ISH HID driver) identifies the device type and registers with the HID core. 2. ISH Implementation: Block Diagram ==================================== @@ -104,7 +104,7 @@ is registered as a device on this bus. The driver, which binds each device The ISH is exposed as "Non-VGA unclassified PCI device" to the host. The PCI product and vendor IDs are changed from different generations of processors. So -the source code which enumerate drivers needs to update from generation to +the source code which enumerates drivers needs to update from generation to generation. 3.2 Inter Processor Communication (IPC) driver @@ -112,41 +112,42 @@ generation. Location: drivers/hid/intel-ish-hid/ipc -The IPC message used memory mapped I/O. The registers are defined in +The IPC message uses memory mapped I/O. The registers are defined in hw-ish-regs.h. 3.2.1 IPC/FW message types ^^^^^^^^^^^^^^^^^^^^^^^^^^ -There are two types of messages, one for management of link and other messages -are to and from transport layers. +There are two types of messages, one for management of link and another for +messages to and from transport layers. TX and RX of Transport messages ............................... -A set of memory mapped register offers support of multi byte messages TX and -RX (E.g.IPC_REG_ISH2HOST_MSG, IPC_REG_HOST2ISH_MSG). The IPC layer maintains -internal queues to sequence messages and send them in order to the FW. +A set of memory mapped register offers support of multi-byte messages TX and +RX (e.g. IPC_REG_ISH2HOST_MSG, IPC_REG_HOST2ISH_MSG). The IPC layer maintains +internal queues to sequence messages and send them in order to the firmware. Optionally the caller can register handler to get notification of completion. -A door bell mechanism is used in messaging to trigger processing in host and +A doorbell mechanism is used in messaging to trigger processing in host and client firmware side. When ISH interrupt handler is called, the ISH2HOST doorbell register is used by host drivers to determine that the interrupt is for ISH. Each side has 32 32-bit message registers and a 32-bit doorbell. Doorbell -register has the following format: -Bits 0..6: fragment length (7 bits are used) -Bits 10..13: encapsulated protocol -Bits 16..19: management command (for IPC management protocol) -Bit 31: doorbell trigger (signal H/W interrupt to the other side) -Other bits are reserved, should be 0. +register has the following format:: + + Bits 0..6: fragment length (7 bits are used) + Bits 10..13: encapsulated protocol + Bits 16..19: management command (for IPC management protocol) + Bit 31: doorbell trigger (signal H/W interrupt to the other side) + Other bits are reserved, should be 0. 3.2.2 Transport layer interface ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ -To abstract HW level IPC communication, a set of callbacks are registered. +To abstract HW level IPC communication, a set of callbacks is registered. The transport layer uses them to send and receive messages. -Refer to struct ishtp_hw_ops for callbacks. +Refer to struct ishtp_hw_ops for callbacks. 3.3 ISH Transport layer ----------------------- @@ -158,7 +159,7 @@ Location: drivers/hid/intel-ish-hid/ishtp/ The transport layer is a bi-directional protocol, which defines: - Set of commands to start, stop, connect, disconnect and flow control -(ishtp/hbm.h) for details +(see ishtp/hbm.h for details) - A flow control mechanism to avoid buffer overflows This protocol resembles bus messages described in the following document: @@ -168,14 +169,14 @@ specifications/dcmi-hi-1-0-spec.pdf "Chapter 7: Bus Message Layer" 3.3.2 Connection and Flow Control Mechanism ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ -Each FW client and a protocol is identified by an UUID. In order to communicate +Each FW client and a protocol is identified by a UUID. In order to communicate to a FW client, a connection must be established using connect request and response bus messages. If successful, a pair (host_client_id and fw_client_id) will identify the connection. Once connection is established, peers send each other flow control bus messages independently. Every peer may send a message only if it has received a -flow-control credit before. Once it sent a message, it may not send another one +flow-control credit before. Once it has sent a message, it may not send another one before receiving the next flow control credit. Either side can send disconnect request bus message to end communication. Also the link will be dropped if major FW reset occurs. @@ -209,7 +210,7 @@ and DMA_XFER_ACK act as ownership indicators. At initial state all outgoing memory belongs to the sender (TX to host, RX to FW), DMA_XFER transfers ownership on the region that contains ISHTP message to the receiving side, DMA_XFER_ACK returns ownership to the sender. A sender -needs not wait for previous DMA_XFER to be ack'ed, and may send another message +need not wait for previous DMA_XFER to be ack'ed, and may send another message as long as remaining continuous memory in its ownership is enough. In principle, multiple DMA_XFER and DMA_XFER_ACK messages may be sent at once (up to IPC MTU), thus allowing for interrupt throttling. @@ -219,8 +220,8 @@ fragments and via IPC otherwise. 3.3.4 Ring Buffers ^^^^^^^^^^^^^^^^^^ -When a client initiate a connection, a ring or RX and TX buffers are allocated. -The size of ring can be specified by the client. HID client set 16 and 32 for +When a client initiates a connection, a ring of RX and TX buffers is allocated. +The size of ring can be specified by the client. HID client sets 16 and 32 for TX and RX buffers respectively. On send request from client, the data to be sent is copied to one of the send ring buffer and scheduled to be sent using bus message protocol. These buffers are required because the FW may have not @@ -230,10 +231,10 @@ to send. Same thing holds true on receive side and flow control is required. 3.3.5 Host Enumeration ^^^^^^^^^^^^^^^^^^^^^^ -The host enumeration bus command allow discovery of clients present in the FW. +The host enumeration bus command allows discovery of clients present in the FW. There can be multiple sensor clients and clients for calibration function. -To ease in implantation and allow independent driver handle each client +To ease implementation and allow independent drivers to handle each client, this transport layer takes advantage of Linux Bus driver model. Each client is registered as device on the transport bus (ishtp bus). @@ -270,7 +271,7 @@ The ISHTP client driver is responsible for: The functionality in these drivers is the same as an external sensor hub. Refer to Documentation/hid/hid-sensor.rst for HID sensor -Documentation/ABI/testing/sysfs-bus-iio for IIO ABIs to user space +Documentation/ABI/testing/sysfs-bus-iio for IIO ABIs to user space. 3.6 End to End HID transport Sequence Diagram --------------------------------------------- @@ -341,9 +342,10 @@ Documentation/ABI/testing/sysfs-bus-iio for IIO ABIs to user space 3.7 ISH Debugging ----------------- -To debug ISH, event tracing mechanism is used. To enable debug logs -echo 1 > /sys/kernel/debug/tracing/events/intel_ish/enable -cat sys/kernel/debug/tracing/trace +To debug ISH, event tracing mechanism is used. To enable debug logs:: + + echo 1 > /sys/kernel/debug/tracing/events/intel_ish/enable + cat sys/kernel/debug/tracing/trace 3.8 ISH IIO sysfs Example on Lenovo thinkpad Yoga 260 ----------------------------------------------------- diff --git a/Documentation/hid/uhid.rst b/Documentation/hid/uhid.rst index b18cb96c885f..2243a6b75914 100644 --- a/Documentation/hid/uhid.rst +++ b/Documentation/hid/uhid.rst @@ -3,7 +3,7 @@ UHID - User-space I/O driver support for HID subsystem ====================================================== UHID allows user-space to implement HID transport drivers. Please see -hid-transport.txt for an introduction into HID transport drivers. This document +hid-transport.rst for an introduction into HID transport drivers. This document relies heavily on the definitions declared there. With UHID, a user-space transport driver can create kernel hid-devices for each @@ -15,7 +15,7 @@ There is an example user-space application in ./samples/uhid/uhid-example.c The UHID API ------------ -UHID is accessed through a character misc-device. The minor-number is allocated +UHID is accessed through a character misc-device. The minor number is allocated dynamically so you need to rely on udev (or similar) to create the device node. This is /dev/uhid by default. @@ -45,23 +45,23 @@ The "type" field defines the payload. For each type, there is a payload-structure available in the union "u" (except for empty payloads). This payload contains management and/or device data. -The first thing you should do is sending an UHID_CREATE2 event. This will -register the device. UHID will respond with an UHID_START event. You can now +The first thing you should do is send a UHID_CREATE2 event. This will +register the device. UHID will respond with a UHID_START event. You can now start sending data to and reading data from UHID. However, unless UHID sends the UHID_OPEN event, the internally attached HID Device Driver has no user attached. That is, you might put your device asleep unless you receive the UHID_OPEN event. If you receive the UHID_OPEN event, you should start I/O. If the last -user closes the HID device, you will receive an UHID_CLOSE event. This may be -followed by an UHID_OPEN event again and so on. There is no need to perform +user closes the HID device, you will receive a UHID_CLOSE event. This may be +followed by a UHID_OPEN event again and so on. There is no need to perform reference-counting in user-space. That is, you will never receive multiple -UHID_OPEN events without an UHID_CLOSE event. The HID subsystem performs +UHID_OPEN events without a UHID_CLOSE event. The HID subsystem performs ref-counting for you. You may decide to ignore UHID_OPEN/UHID_CLOSE, though. I/O is allowed even though the device may have no users. If you want to send data on the interrupt channel to the HID subsystem, you send -an HID_INPUT2 event with your raw data payload. If the kernel wants to send data -on the interrupt channel to the device, you will read an UHID_OUTPUT event. +a HID_INPUT2 event with your raw data payload. If the kernel wants to send data +on the interrupt channel to the device, you will read a UHID_OUTPUT event. Data requests on the control channel are currently limited to GET_REPORT and SET_REPORT (no other data reports on the control channel are defined so far). Those requests are always synchronous. That means, the kernel sends @@ -71,7 +71,7 @@ the response via UHID_GET_REPORT_REPLY and UHID_SET_REPORT_REPLY to the kernel. The kernel blocks internal driver-execution during such round-trips (times out after a hard-coded period). -If your device disconnects, you should send an UHID_DESTROY event. This will +If your device disconnects, you should send a UHID_DESTROY event. This will unregister the device. You can now send UHID_CREATE2 again to register a new device. If you close() the fd, the device is automatically unregistered and destroyed @@ -125,7 +125,7 @@ UHID_START: This is sent when the HID device is started. Consider this as an answer to UHID_CREATE2. This is always the first event that is sent. Note that this event might not be available immediately after write(UHID_CREATE2) returns. - Device drivers might required delayed setups. + Device drivers might require delayed setups. This event contains a payload of type uhid_start_req. The "dev_flags" field describes special behaviors of a device. The following flags are defined: @@ -149,7 +149,7 @@ UHID_STOP: reloaded/changed the device driver loaded on your HID device (or some other maintenance actions happened). - You can usually ignored any UHID_STOP events safely. + You can usually ignore any UHID_STOP events safely. UHID_OPEN: This is sent when the HID device is opened. That is, the data that the HID @@ -166,17 +166,17 @@ UHID_OUTPUT: This is sent if the HID device driver wants to send raw data to the I/O device on the interrupt channel. You should read the payload and forward it to the device. The payload is of type "struct uhid_output_req". - This may be received even though you haven't received UHID_OPEN, yet. + This may be received even though you haven't received UHID_OPEN yet. UHID_GET_REPORT: This event is sent if the kernel driver wants to perform a GET_REPORT request - on the control channeld as described in the HID specs. The report-type and + on the control channel as described in the HID specs. The report-type and report-number are available in the payload. The kernel serializes GET_REPORT requests so there will never be two in parallel. However, if you fail to respond with a UHID_GET_REPORT_REPLY, the request might silently time out. - Once you read a GET_REPORT request, you shall forward it to the hid device and - remember the "id" field in the payload. Once your hid device responds to the + Once you read a GET_REPORT request, you shall forward it to the HID device and + remember the "id" field in the payload. Once your HID device responds to the GET_REPORT (or if it fails), you must send a UHID_GET_REPORT_REPLY to the kernel with the exact same "id" as in the request. If the request already timed out, the kernel will ignore the response silently. The "id" field is @@ -184,7 +184,7 @@ UHID_GET_REPORT: UHID_SET_REPORT: This is the SET_REPORT equivalent of UHID_GET_REPORT. On receipt, you shall - send a SET_REPORT request to your hid device. Once it replies, you must tell + send a SET_REPORT request to your HID device. Once it replies, you must tell the kernel about it via UHID_SET_REPORT_REPLY. The same restrictions as for UHID_GET_REPORT apply. diff --git a/MAINTAINERS b/MAINTAINERS index a9efff1a18c6..dace4bd105d5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7908,6 +7908,12 @@ F: drivers/hid/ F: include/linux/hid* F: include/uapi/linux/hid* +HID PLAYSTATION DRIVER +M: Roderick Colenbrander <roderick.colenbrander@sony.com> +L: linux-input@vger.kernel.org +S: Supported +F: drivers/hid/hid-playstation.c + HID SENSOR HUB DRIVERS M: Jiri Kosina <jikos@kernel.org> M: Jonathan Cameron <jic23@kernel.org> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 43c4280bfc4f..d612f633b771 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -770,7 +770,8 @@ CONFIG_SND_SOC_LPASS_VA_MACRO=m CONFIG_SND_SIMPLE_CARD=m CONFIG_SND_AUDIO_GRAPH_CARD=m CONFIG_HID_MULTITOUCH=m -CONFIG_I2C_HID=m +CONFIG_I2C_HID_ACPI=m +CONFIG_I2C_HID_OF=m CONFIG_USB_CONN_GPIO=m CONFIG_USB=y CONFIG_USB_OTG=y diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig index 09fa75a2b289..786b71ef7738 100644 --- a/drivers/hid/Kconfig +++ b/drivers/hid/Kconfig @@ -853,6 +853,24 @@ config HID_PLANTRONICS Say M here if you may ever plug in a Plantronics USB audio device. +config HID_PLAYSTATION + tristate "PlayStation HID Driver" + depends on HID + select CRC32 + select POWER_SUPPLY + help + Provides support for Sony PS5 controllers including support for + its special functionalities e.g. touchpad, lights and motion + sensors. + +config PLAYSTATION_FF + bool "PlayStation force feedback support" + depends on HID_PLAYSTATION + select INPUT_FF_MEMLESS + help + Say Y here if you would like to enable force feedback support for + PlayStation game controllers. + config HID_PRIMAX tristate "Primax non-fully HID-compliant devices" depends on HID @@ -909,6 +927,7 @@ config HID_SONY * Sony PS3 Blue-ray Disk Remote Control (Bluetooth) * Logitech Harmony adapter for Sony Playstation 3 (Bluetooth) * Guitar Hero Live PS3 and Wii U guitar dongles + * Guitar Hero PS3 and PC guitar dongles config SONY_FF bool "Sony PS2/3/4 accessories force feedback support" diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile index 014d21fe7dac..c4f6d5c613dc 100644 --- a/drivers/hid/Makefile +++ b/drivers/hid/Makefile @@ -94,6 +94,7 @@ hid-picolcd-$(CONFIG_HID_PICOLCD_CIR) += hid-picolcd_cir.o hid-picolcd-$(CONFIG_DEBUG_FS) += hid-picolcd_debugfs.o obj-$(CONFIG_HID_PLANTRONICS) += hid-plantronics.o +obj-$(CONFIG_HID_PLAYSTATION) += hid-playstation.o obj-$(CONFIG_HID_PRIMAX) += hid-primax.o obj-$(CONFIG_HID_REDRAGON) += hid-redragon.o obj-$(CONFIG_HID_RETRODE) += hid-retrode.o @@ -138,7 +139,7 @@ obj-$(CONFIG_USB_HID) += usbhid/ obj-$(CONFIG_USB_MOUSE) += usbhid/ obj-$(CONFIG_USB_KBD) += usbhid/ -obj-$(CONFIG_I2C_HID) += i2c-hid/ +obj-$(CONFIG_I2C_HID_CORE) += i2c-hid/ obj-$(CONFIG_INTEL_ISH_HID) += intel-ish-hid/ obj-$(INTEL_ISH_FIRMWARE_DOWNLOADER) += intel-ish-hid/ diff --git a/drivers/hid/hid-chicony.c b/drivers/hid/hid-chicony.c index 3f0ed6a95223..ca556d39da2a 100644 --- a/drivers/hid/hid-chicony.c +++ b/drivers/hid/hid-chicony.c @@ -21,6 +21,39 @@ #include "hid-ids.h" +#define CH_WIRELESS_CTL_REPORT_ID 0x11 + +static int ch_report_wireless(struct hid_report *report, u8 *data, int size) +{ + struct hid_device *hdev = report->device; + struct input_dev *input; + + if (report->id != CH_WIRELESS_CTL_REPORT_ID || report->maxfield != 1) + return 0; + + input = report->field[0]->hidinput->input; + if (!input) { + hid_warn(hdev, "can't find wireless radio control's input"); + return 0; + } + + input_report_key(input, KEY_RFKILL, 1); + input_sync(input); + input_report_key(input, KEY_RFKILL, 0); + input_sync(input); + + return 1; +} + +static int ch_raw_event(struct hid_device *hdev, + struct hid_report *report, u8 *data, int size) +{ + if (report->application == HID_GD_WIRELESS_RADIO_CTLS) + return ch_report_wireless(report, data, size); + + return 0; +} + #define ch_map_key_clear(c) hid_map_usage_clear(hi, usage, bit, max, \ EV_KEY, (c)) static int ch_input_mapping(struct hid_device *hdev, struct hid_input *hi, @@ -77,10 +110,30 @@ static __u8 *ch_switch12_report_fixup(struct hid_device *hdev, __u8 *rdesc, return rdesc; } +static int ch_probe(struct hid_device *hdev, const struct hid_device_id *id) +{ + int ret; + + hdev->quirks |= HID_QUIRK_INPUT_PER_APP; + ret = hid_parse(hdev); + if (ret) { + hid_err(hdev, "Chicony hid parse failed: %d\n", ret); + return ret; + } + + ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT); + if (ret) { + hid_err(hdev, "Chicony hw start failed: %d\n", ret); + return ret; + } + + return 0; +} static const struct hid_device_id ch_devices[] = { { HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_TACTICAL_PAD) }, { HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_WIRELESS2) }, + { HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_WIRELESS3) }, { HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_ACER_SWITCH12) }, { } }; @@ -91,6 +144,8 @@ static struct hid_driver ch_driver = { .id_table = ch_devices, .report_fixup = ch_switch12_report_fixup, .input_mapping = ch_input_mapping, + .probe = ch_probe, + .raw_event = ch_raw_event, }; module_hid_driver(ch_driver); diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c index 56172fe6995c..097cb1ee3126 100644 --- a/drivers/hid/hid-core.c +++ b/drivers/hid/hid-core.c @@ -90,7 +90,7 @@ EXPORT_SYMBOL_GPL(hid_register_report); * Register a new field for this report. */ -static struct hid_field *hid_register_field(struct hid_report *report, unsigned usages, unsigned values) +static struct hid_field *hid_register_field(struct hid_report *report, unsigned usages) { struct hid_field *field; @@ -101,7 +101,7 @@ static struct hid_field *hid_register_field(struct hid_report *report, unsigned field = kzalloc((sizeof(struct hid_field) + usages * sizeof(struct hid_usage) + - values * sizeof(unsigned)), GFP_KERNEL); + usages * sizeof(unsigned)), GFP_KERNEL); if (!field) return NULL; @@ -300,7 +300,7 @@ static int hid_add_field(struct hid_parser *parser, unsigned report_type, unsign usages = max_t(unsigned, parser->local.usage_index, parser->global.report_count); - field = hid_register_field(report, usages, parser->global.report_count); + field = hid_register_field(report, usages); if (!field) return 0; @@ -1307,6 +1307,9 @@ EXPORT_SYMBOL_GPL(hid_open_report); static s32 snto32(__u32 value, unsigned n) { + if (!value || !n) + return 0; + switch (n) { case 8: return ((__s8)value); case 16: return ((__s16)value); diff --git a/drivers/hid/hid-google-hammer.c b/drivers/hid/hid-google-hammer.c index 85a054f1ce38..d9319622da44 100644 --- a/drivers/hid/hid-google-hammer.c +++ b/drivers/hid/hid-google-hammer.c @@ -392,30 +392,34 @@ static int hammer_input_mapping(struct hid_device *hdev, struct hid_input *hi, return 0; } -static int hammer_event(struct hid_device *hid, struct hid_field *field, - struct hid_usage *usage, __s32 value) +static void hammer_folded_event(struct hid_device *hdev, bool folded) { unsigned long flags; - if (usage->hid == HID_USAGE_KBD_FOLDED) { - spin_lock_irqsave(&cbas_ec_lock, flags); + spin_lock_irqsave(&cbas_ec_lock, flags); - /* - * If we are getting events from Whiskers that means that it - * is attached to the lid. - */ - cbas_ec.base_present = true; - cbas_ec.base_folded = value; - hid_dbg(hid, "%s: base: %d, folded: %d\n", __func__, - cbas_ec.base_present, cbas_ec.base_folded); - - if (cbas_ec.input) { - input_report_switch(cbas_ec.input, - SW_TABLET_MODE, value); - input_sync(cbas_ec.input); - } + /* + * If we are getting events from Whiskers that means that it + * is attached to the lid. + */ + cbas_ec.base_present = true; + cbas_ec.base_folded = folded; + hid_dbg(hdev, "%s: base: %d, folded: %d\n", __func__, + cbas_ec.base_present, cbas_ec.base_folded); - spin_unlock_irqrestore(&cbas_ec_lock, flags); + if (cbas_ec.input) { + input_report_switch(cbas_ec.input, SW_TABLET_MODE, folded); + input_sync(cbas_ec.input); + } + + spin_unlock_irqrestore(&cbas_ec_lock, flags); +} + +static int hammer_event(struct hid_device *hid, struct hid_field *field, + struct hid_usage *usage, __s32 value) +{ + if (usage->hid == HID_USAGE_KBD_FOLDED) { + hammer_folded_event(hid, value); return 1; /* We handled this event */ } @@ -457,6 +461,47 @@ static bool hammer_has_backlight_control(struct hid_device *hdev) HID_GD_KEYBOARD, HID_AD_BRIGHTNESS); } +static void hammer_get_folded_state(struct hid_device *hdev) +{ + struct hid_report *report; + char *buf; + int len, rlen; + int a; + + report = hdev->report_enum[HID_INPUT_REPORT].report_id_hash[0x0]; + + if (!report || report->maxfield < 1) + return; + + len = hid_report_len(report) + 1; + + buf = kmalloc(len, GFP_KERNEL); + if (!buf) + return; + + rlen = hid_hw_raw_request(hdev, report->id, buf, len, report->type, HID_REQ_GET_REPORT); + + if (rlen != len) { + hid_warn(hdev, "Unable to read base folded state: %d (expected %d)\n", rlen, len); + goto out; + } + + for (a = 0; a < report->maxfield; a++) { + struct hid_field *field = report->field[a]; + + if (field->usage->hid == HID_USAGE_KBD_FOLDED) { + u32 value = hid_field_extract(hdev, buf+1, + field->report_offset, field->report_size); + + hammer_folded_event(hdev, value); + break; + } + } + +out: + kfree(buf); +} + static int hammer_probe(struct hid_device *hdev, const struct hid_device_id *id) { @@ -481,6 +526,8 @@ static int hammer_probe(struct hid_device *hdev, error = hid_hw_open(hdev); if (error) return error; + + hammer_get_folded_state(hdev); } if (hammer_has_backlight_control(hdev)) { diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h index 5ba0aa1d2335..e42aaae3138f 100644 --- a/drivers/hid/hid-ids.h +++ b/drivers/hid/hid-ids.h @@ -40,6 +40,9 @@ #define USB_VENDOR_ID_ACTIONSTAR 0x2101 #define USB_DEVICE_ID_ACTIONSTAR_1011 0x1011 +#define USB_VENDOR_ID_ACTIVISION 0x1430 +#define USB_DEVICE_ID_ACTIVISION_GUITAR_DONGLE 0x474c + #define USB_VENDOR_ID_ADS_TECH 0x06e1 #define USB_DEVICE_ID_ADS_TECH_RADIO_SI470X 0xa155 @@ -270,6 +273,7 @@ #define USB_DEVICE_ID_CHICONY_PIXART_USB_OPTICAL_MOUSE 0x1053 #define USB_DEVICE_ID_CHICONY_PIXART_USB_OPTICAL_MOUSE2 0x0939 #define USB_DEVICE_ID_CHICONY_WIRELESS2 0x1123 +#define USB_DEVICE_ID_CHICONY_WIRELESS3 0x1236 #define USB_DEVICE_ID_ASUS_AK1D 0x1125 #define USB_DEVICE_ID_CHICONY_TOSHIBA_WT10A 0x1408 #define USB_DEVICE_ID_CHICONY_ACER_SWITCH12 0x1421 @@ -389,6 +393,7 @@ #define USB_DEVICE_ID_TOSHIBA_CLICK_L9W 0x0401 #define USB_DEVICE_ID_HP_X2 0x074d #define USB_DEVICE_ID_HP_X2_10_COVER 0x0755 +#define I2C_DEVICE_ID_HP_SPECTRE_X360_15 0x2817 #define USB_DEVICE_ID_ASUS_UX550_TOUCHSCREEN 0x2706 #define USB_VENDOR_ID_ELECOM 0x056e @@ -641,6 +646,8 @@ #define USB_DEVICE_ID_INNEX_GENESIS_ATARI 0x4745 #define USB_VENDOR_ID_ITE 0x048d +#define I2C_VENDOR_ID_ITE 0x103c +#define I2C_DEVICE_ID_ITE_VOYO_WINPAD_A15 0x184f #define USB_DEVICE_ID_ITE_LENOVO_YOGA 0x8386 #define USB_DEVICE_ID_ITE_LENOVO_YOGA2 0x8350 #define I2C_DEVICE_ID_ITE_LENOVO_LEGION_Y720 0x837a @@ -1073,13 +1080,15 @@ #define USB_DEVICE_ID_SONY_PS4_CONTROLLER 0x05c4 #define USB_DEVICE_ID_SONY_PS4_CONTROLLER_2 0x09cc #define USB_DEVICE_ID_SONY_PS4_CONTROLLER_DONGLE 0x0ba0 +#define USB_DEVICE_ID_SONY_PS5_CONTROLLER 0x0ce6 #define USB_DEVICE_ID_SONY_MOTION_CONTROLLER 0x03d5 #define USB_DEVICE_ID_SONY_NAVIGATION_CONTROLLER 0x042f #define USB_DEVICE_ID_SONY_BUZZ_CONTROLLER 0x0002 #define USB_DEVICE_ID_SONY_WIRELESS_BUZZ_CONTROLLER 0x1000 -#define USB_VENDOR_ID_SONY_GHLIVE 0x12ba +#define USB_VENDOR_ID_SONY_RHYTHM 0x12ba #define USB_DEVICE_ID_SONY_PS3WIIU_GHLIVE_DONGLE 0x074b +#define USB_DEVICE_ID_SONY_PS3_GUITAR_DONGLE 0x0100 #define USB_VENDOR_ID_SINO_LITE 0x1345 #define USB_DEVICE_ID_SINO_LITE_CONTROLLER 0x3008 diff --git a/drivers/hid/hid-input.c b/drivers/hid/hid-input.c index f23027d2795b..236bccd37760 100644 --- a/drivers/hid/hid-input.c +++ b/drivers/hid/hid-input.c @@ -324,6 +324,8 @@ static const struct hid_device_id hid_battery_quirks[] = { HID_BATTERY_QUIRK_IGNORE }, { HID_USB_DEVICE(USB_VENDOR_ID_ELAN, USB_DEVICE_ID_ASUS_UX550_TOUCHSCREEN), HID_BATTERY_QUIRK_IGNORE }, + { HID_I2C_DEVICE(USB_VENDOR_ID_ELAN, I2C_DEVICE_ID_HP_SPECTRE_X360_15), + HID_BATTERY_QUIRK_IGNORE }, {} }; @@ -1854,6 +1856,16 @@ static struct hid_input *hidinput_match_application(struct hid_report *report) list_for_each_entry(hidinput, &hid->inputs, list) { if (hidinput->application == report->application) return hidinput; + + /* + * Keep SystemControl and ConsumerControl applications together + * with the main keyboard, if present. + */ + if ((report->application == HID_GD_SYSTEM_CONTROL || + report->application == HID_CP_CONSUMER_CONTROL) && + hidinput->application == HID_GD_KEYBOARD) { + return hidinput; + } } return NULL; diff --git a/drivers/hid/hid-ite.c b/drivers/hid/hid-ite.c index 22bfbebceaf4..14fc068affad 100644 --- a/drivers/hid/hid-ite.c +++ b/drivers/hid/hid-ite.c @@ -23,11 +23,16 @@ static __u8 *ite_report_fixup(struct hid_device *hdev, __u8 *rdesc, unsigned int hid_info(hdev, "Fixing up Acer Sw5-012 ITE keyboard report descriptor\n"); rdesc[163] = HID_MAIN_ITEM_RELATIVE; } - /* For Acer One S1002 keyboard-dock */ + /* For Acer One S1002/S1003 keyboard-dock */ if (*rsize == 188 && rdesc[185] == 0x81 && rdesc[186] == 0x02) { - hid_info(hdev, "Fixing up Acer S1002 ITE keyboard report descriptor\n"); + hid_info(hdev, "Fixing up Acer S1002/S1003 ITE keyboard report descriptor\n"); rdesc[186] = HID_MAIN_ITEM_RELATIVE; } + /* For Acer Aspire Switch 10E (SW3-016) keyboard-dock */ + if (*rsize == 210 && rdesc[184] == 0x81 && rdesc[185] == 0x02) { + hid_info(hdev, "Fixing up Acer Aspire Switch 10E (SW3-016) ITE keyboard report descriptor\n"); + rdesc[185] = HID_MAIN_ITEM_RELATIVE; + } } return rdesc; @@ -114,7 +119,8 @@ static const struct hid_device_id ite_devices[] = { /* ITE8910 USB kbd ctlr, with Synaptics touchpad connected to it. */ { HID_DEVICE(BUS_USB, HID_GROUP_GENERIC, USB_VENDOR_ID_SYNAPTICS, - USB_DEVICE_ID_SYNAPTICS_ACER_ONE_S1003) }, + USB_DEVICE_ID_SYNAPTICS_ACER_ONE_S1003), + .driver_data = QUIRK_TOUCHPAD_ON_OFF_REPORT }, { } }; MODULE_DEVICE_TABLE(hid, ite_devices); diff --git a/drivers/hid/hid-lg-g15.c b/drivers/hid/hid-lg-g15.c index fcaf8466e627..bfbba0d41933 100644 --- a/drivers/hid/hid-lg-g15.c +++ b/drivers/hid/hid-lg-g15.c @@ -647,7 +647,7 @@ static void lg_g15_input_close(struct input_dev *dev) static int lg_g15_register_led(struct lg_g15_data *g15, int i) { - const char * const led_names[] = { + static const char * const led_names[] = { "g15::kbd_backlight", "g15::lcd_backlight", "g15::macro_preset1", diff --git a/drivers/hid/hid-logitech-dj.c b/drivers/hid/hid-logitech-dj.c index 45e7e0bdd382..271bd8d24339 100644 --- a/drivers/hid/hid-logitech-dj.c +++ b/drivers/hid/hid-logitech-dj.c @@ -980,6 +980,7 @@ static void logi_hidpp_recv_queue_notif(struct hid_device *hdev, case 0x07: device_type = "eQUAD step 4 Gaming"; logi_hidpp_dev_conn_notif_equad(hdev, hidpp_report, &workitem); + workitem.reports_supported |= STD_KEYBOARD; break; case 0x08: device_type = "eQUAD step 4 for gamepads"; @@ -994,7 +995,12 @@ static void logi_hidpp_recv_queue_notif(struct hid_device *hdev, workitem.reports_supported |= STD_KEYBOARD; break; case 0x0d: - device_type = "eQUAD Lightspeed 1_1"; + device_type = "eQUAD Lightspeed 1.1"; + logi_hidpp_dev_conn_notif_equad(hdev, hidpp_report, &workitem); + workitem.reports_supported |= STD_KEYBOARD; + break; + case 0x0f: + device_type = "eQUAD Lightspeed 1.2"; logi_hidpp_dev_conn_notif_equad(hdev, hidpp_report, &workitem); workitem.reports_supported |= STD_KEYBOARD; break; diff --git a/drivers/hid/hid-logitech-hidpp.c b/drivers/hid/hid-logitech-hidpp.c index 7eb9a6ddb46a..d459e2dbe647 100644 --- a/drivers/hid/hid-logitech-hidpp.c +++ b/drivers/hid/hid-logitech-hidpp.c @@ -92,6 +92,8 @@ MODULE_PARM_DESC(disable_tap_to_click, #define HIDPP_CAPABILITY_BATTERY_MILEAGE BIT(2) #define HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS BIT(3) #define HIDPP_CAPABILITY_BATTERY_VOLTAGE BIT(4) +#define HIDPP_CAPABILITY_BATTERY_PERCENTAGE BIT(5) +#define HIDPP_CAPABILITY_UNIFIED_BATTERY BIT(6) #define lg_map_key_clear(c) hid_map_usage_clear(hi, usage, bit, max, EV_KEY, (c)) @@ -152,6 +154,7 @@ struct hidpp_battery { int voltage; int charge_type; bool online; + u8 supported_levels_1004; }; /** @@ -1171,7 +1174,7 @@ static int hidpp20_batterylevel_get_battery_info(struct hidpp_device *hidpp, return 0; } -static int hidpp20_query_battery_info(struct hidpp_device *hidpp) +static int hidpp20_query_battery_info_1000(struct hidpp_device *hidpp) { u8 feature_type; int ret; @@ -1208,7 +1211,7 @@ static int hidpp20_query_battery_info(struct hidpp_device *hidpp) return 0; } -static int hidpp20_battery_event(struct hidpp_device *hidpp, +static int hidpp20_battery_event_1000(struct hidpp_device *hidpp, u8 *data, int size) { struct hidpp_report *report = (struct hidpp_report *)data; @@ -1380,6 +1383,224 @@ static int hidpp20_battery_voltage_event(struct hidpp_device *hidpp, return 0; } +/* -------------------------------------------------------------------------- */ +/* 0x1004: Unified battery */ +/* -------------------------------------------------------------------------- */ + +#define HIDPP_PAGE_UNIFIED_BATTERY 0x1004 + +#define CMD_UNIFIED_BATTERY_GET_CAPABILITIES 0x00 +#define CMD_UNIFIED_BATTERY_GET_STATUS 0x10 + +#define EVENT_UNIFIED_BATTERY_STATUS_EVENT 0x00 + +#define FLAG_UNIFIED_BATTERY_LEVEL_CRITICAL BIT(0) +#define FLAG_UNIFIED_BATTERY_LEVEL_LOW BIT(1) +#define FLAG_UNIFIED_BATTERY_LEVEL_GOOD BIT(2) +#define FLAG_UNIFIED_BATTERY_LEVEL_FULL BIT(3) + +#define FLAG_UNIFIED_BATTERY_FLAGS_RECHARGEABLE BIT(0) +#define FLAG_UNIFIED_BATTERY_FLAGS_STATE_OF_CHARGE BIT(1) + +static int hidpp20_unifiedbattery_get_capabilities(struct hidpp_device *hidpp, + u8 feature_index) +{ + struct hidpp_report response; + int ret; + u8 *params = (u8 *)response.fap.params; + + if (hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS || + hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_PERCENTAGE) { + /* we have already set the device capabilities, so let's skip */ + return 0; + } + + ret = hidpp_send_fap_command_sync(hidpp, feature_index, + CMD_UNIFIED_BATTERY_GET_CAPABILITIES, + NULL, 0, &response); + /* Ignore these intermittent errors */ + if (ret == HIDPP_ERROR_RESOURCE_ERROR) + return -EIO; + if (ret > 0) { + hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n", + __func__, ret); + return -EPROTO; + } + if (ret) + return ret; + + /* + * If the device supports state of charge (battery percentage) we won't + * export the battery level information. there are 4 possible battery + * levels and they all are optional, this means that the device might + * not support any of them, we are just better off with the battery + * percentage. + */ + if (params[1] & FLAG_UNIFIED_BATTERY_FLAGS_STATE_OF_CHARGE) { + hidpp->capabilities |= HIDPP_CAPABILITY_BATTERY_PERCENTAGE; + hidpp->battery.supported_levels_1004 = 0; + } else { + hidpp->capabilities |= HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS; + hidpp->battery.supported_levels_1004 = params[0]; + } + + return 0; +} + +static int hidpp20_unifiedbattery_map_status(struct hidpp_device *hidpp, + u8 charging_status, + u8 external_power_status) +{ + int status; + + switch (charging_status) { + case 0: /* discharging */ + status = POWER_SUPPLY_STATUS_DISCHARGING; + break; + case 1: /* charging */ + case 2: /* charging slow */ + status = POWER_SUPPLY_STATUS_CHARGING; + break; + case 3: /* complete */ + status = POWER_SUPPLY_STATUS_FULL; + break; + case 4: /* error */ + status = POWER_SUPPLY_STATUS_NOT_CHARGING; + hid_info(hidpp->hid_dev, "%s: charging error", + hidpp->name); + break; + default: + status = POWER_SUPPLY_STATUS_NOT_CHARGING; + break; + } + + return status; +} + +static int hidpp20_unifiedbattery_map_level(struct hidpp_device *hidpp, + u8 battery_level) +{ + /* cler unsupported level bits */ + battery_level &= hidpp->battery.supported_levels_1004; + + if (battery_level & FLAG_UNIFIED_BATTERY_LEVEL_FULL) + return POWER_SUPPLY_CAPACITY_LEVEL_FULL; + else if (battery_level & FLAG_UNIFIED_BATTERY_LEVEL_GOOD) + return POWER_SUPPLY_CAPACITY_LEVEL_NORMAL; + else if (battery_level & FLAG_UNIFIED_BATTERY_LEVEL_LOW) + return POWER_SUPPLY_CAPACITY_LEVEL_LOW; + else if (battery_level & FLAG_UNIFIED_BATTERY_LEVEL_CRITICAL) + return POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL; + + return POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; +} + +static int hidpp20_unifiedbattery_get_status(struct hidpp_device *hidpp, + u8 feature_index, + u8 *state_of_charge, + int *status, + int *level) +{ + struct hidpp_report response; + int ret; + u8 *params = (u8 *)response.fap.params; + + ret = hidpp_send_fap_command_sync(hidpp, feature_index, + CMD_UNIFIED_BATTERY_GET_STATUS, + NULL, 0, &response); + /* Ignore these intermittent errors */ + if (ret == HIDPP_ERROR_RESOURCE_ERROR) + return -EIO; + if (ret > 0) { + hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n", + __func__, ret); + return -EPROTO; + } + if (ret) + return ret; + + *state_of_charge = params[0]; + *status = hidpp20_unifiedbattery_map_status(hidpp, params[2], params[3]); + *level = hidpp20_unifiedbattery_map_level(hidpp, params[1]); + + return 0; +} + +static int hidpp20_query_battery_info_1004(struct hidpp_device *hidpp) +{ + u8 feature_type; + int ret; + u8 state_of_charge; + int status, level; + + if (hidpp->battery.feature_index == 0xff) { + ret = hidpp_root_get_feature(hidpp, + HIDPP_PAGE_UNIFIED_BATTERY, + &hidpp->battery.feature_index, + &feature_type); + if (ret) + return ret; + } + + ret = hidpp20_unifiedbattery_get_capabilities(hidpp, + hidpp->battery.feature_index); + if (ret) + return ret; + + ret = hidpp20_unifiedbattery_get_status(hidpp, + hidpp->battery.feature_index, + &state_of_charge, + &status, + &level); + if (ret) + return ret; + + hidpp->capabilities |= HIDPP_CAPABILITY_UNIFIED_BATTERY; + hidpp->battery.capacity = state_of_charge; + hidpp->battery.status = status; + hidpp->battery.level = level; + hidpp->battery.online = true; + + return 0; +} + +static int hidpp20_battery_event_1004(struct hidpp_device *hidpp, + u8 *data, int size) +{ + struct hidpp_report *report = (struct hidpp_report *)data; + u8 *params = (u8 *)report->fap.params; + int state_of_charge, status, level; + bool changed; + + if (report->fap.feature_index != hidpp->battery.feature_index || + report->fap.funcindex_clientid != EVENT_UNIFIED_BATTERY_STATUS_EVENT) + return 0; + + state_of_charge = params[0]; + status = hidpp20_unifiedbattery_map_status(hidpp, params[2], params[3]); + level = hidpp20_unifiedbattery_map_level(hidpp, params[1]); + + changed = status != hidpp->battery.status || + (state_of_charge != hidpp->battery.capacity && + hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_PERCENTAGE) || + (level != hidpp->battery.level && + hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS); + + if (changed) { + hidpp->battery.capacity = state_of_charge; + hidpp->battery.status = status; + hidpp->battery.level = level; + if (hidpp->battery.ps) + power_supply_changed(hidpp->battery.ps); + } + + return 0; +} + +/* -------------------------------------------------------------------------- */ +/* Battery feature helpers */ +/* -------------------------------------------------------------------------- */ + static enum power_supply_property hidpp_battery_props[] = { POWER_SUPPLY_PROP_ONLINE, POWER_SUPPLY_PROP_STATUS, @@ -3307,7 +3528,10 @@ static int hidpp_raw_hidpp_event(struct hidpp_device *hidpp, u8 *data, } if (hidpp->capabilities & HIDPP_CAPABILITY_HIDPP20_BATTERY) { - ret = hidpp20_battery_event(hidpp, data, size); + ret = hidpp20_battery_event_1000(hidpp, data, size); + if (ret != 0) + return ret; + ret = hidpp20_battery_event_1004(hidpp, data, size); if (ret != 0) return ret; ret = hidpp_solar_battery_event(hidpp, data, size); @@ -3443,9 +3667,14 @@ static int hidpp_initialize_battery(struct hidpp_device *hidpp) if (hidpp->quirks & HIDPP_QUIRK_CLASS_K750) ret = hidpp_solar_request_battery_event(hidpp); else { - ret = hidpp20_query_battery_voltage_info(hidpp); + /* we only support one battery feature right now, so let's + first check the ones that support battery level first + and leave voltage for last */ + ret = hidpp20_query_battery_info_1000(hidpp); + if (ret) + ret = hidpp20_query_battery_info_1004(hidpp); if (ret) - ret = hidpp20_query_battery_info(hidpp); + ret = hidpp20_query_battery_voltage_info(hidpp); } if (ret) @@ -3473,7 +3702,8 @@ static int hidpp_initialize_battery(struct hidpp_device *hidpp) num_battery_props = ARRAY_SIZE(hidpp_battery_props) - 3; - if (hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_MILEAGE) + if (hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_MILEAGE || + hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_PERCENTAGE) battery_props[num_battery_props++] = POWER_SUPPLY_PROP_CAPACITY; @@ -3650,8 +3880,10 @@ static void hidpp_connect_event(struct hidpp_device *hidpp) } else if (hidpp->capabilities & HIDPP_CAPABILITY_HIDPP20_BATTERY) { if (hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_VOLTAGE) hidpp20_query_battery_voltage_info(hidpp); + else if (hidpp->capabilities & HIDPP_CAPABILITY_UNIFIED_BATTERY) + hidpp20_query_battery_info_1004(hidpp); else - hidpp20_query_battery_info(hidpp); + hidpp20_query_battery_info_1000(hidpp); } if (hidpp->battery.ps) power_supply_changed(hidpp->battery.ps); diff --git a/drivers/hid/hid-multitouch.c b/drivers/hid/hid-multitouch.c index 8429ebe7097e..9d9f3e1bd5f4 100644 --- a/drivers/hid/hid-multitouch.c +++ b/drivers/hid/hid-multitouch.c @@ -1747,6 +1747,13 @@ static int mt_probe(struct hid_device *hdev, const struct hid_device_id *id) } #ifdef CONFIG_PM +static int mt_suspend(struct hid_device *hdev, pm_message_t state) +{ + /* High latency is desirable for power savings during S3/S0ix */ + mt_set_modes(hdev, HID_LATENCY_HIGH, true, true); + return 0; +} + static int mt_reset_resume(struct hid_device *hdev) { mt_release_contacts(hdev); @@ -1762,6 +1769,8 @@ static int mt_resume(struct hid_device *hdev) hid_hw_idle(hdev, 0, 0, HID_REQ_SET_IDLE); + mt_set_modes(hdev, HID_LATENCY_NORMAL, true, true); + return 0; } #endif @@ -2155,6 +2164,7 @@ static struct hid_driver mt_driver = { .event = mt_event, .report = mt_report, #ifdef CONFIG_PM + .suspend = mt_suspend, .reset_resume = mt_reset_resume, .resume = mt_resume, #endif diff --git a/drivers/hid/hid-playstation.c b/drivers/hid/hid-playstation.c new file mode 100644 index 000000000000..ab7c82c2e886 --- /dev/null +++ b/drivers/hid/hid-playstation.c @@ -0,0 +1,1351 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * HID driver for Sony DualSense(TM) controller. + * + * Copyright (c) 2020 Sony Interactive Entertainment + */ + +#include <linux/bits.h> +#include <linux/crc32.h> +#include <linux/device.h> +#include <linux/hid.h> +#include <linux/idr.h> +#include <linux/input/mt.h> +#include <linux/module.h> + +#include <asm/unaligned.h> + +#include "hid-ids.h" + +/* List of connected playstation devices. */ +static DEFINE_MUTEX(ps_devices_lock); +static LIST_HEAD(ps_devices_list); + +static DEFINE_IDA(ps_player_id_allocator); + +#define HID_PLAYSTATION_VERSION_PATCH 0x8000 + +/* Base class for playstation devices. */ +struct ps_device { + struct list_head list; + struct hid_device *hdev; + spinlock_t lock; + + uint32_t player_id; + + struct power_supply_desc battery_desc; + struct power_supply *battery; + uint8_t battery_capacity; + int battery_status; + + uint8_t mac_address[6]; /* Note: stored in little endian order. */ + uint32_t hw_version; + uint32_t fw_version; + + int (*parse_report)(struct ps_device *dev, struct hid_report *report, u8 *data, int size); +}; + +/* Calibration data for playstation motion sensors. */ +struct ps_calibration_data { + int abs_code; + short bias; + int sens_numer; + int sens_denom; +}; + +/* Seed values for DualShock4 / DualSense CRC32 for different report types. */ +#define PS_INPUT_CRC32_SEED 0xA1 +#define PS_OUTPUT_CRC32_SEED 0xA2 +#define PS_FEATURE_CRC32_SEED 0xA3 + +#define DS_INPUT_REPORT_USB 0x01 +#define DS_INPUT_REPORT_USB_SIZE 64 +#define DS_INPUT_REPORT_BT 0x31 +#define DS_INPUT_REPORT_BT_SIZE 78 +#define DS_OUTPUT_REPORT_USB 0x02 +#define DS_OUTPUT_REPORT_USB_SIZE 63 +#define DS_OUTPUT_REPORT_BT 0x31 +#define DS_OUTPUT_REPORT_BT_SIZE 78 + +#define DS_FEATURE_REPORT_CALIBRATION 0x05 +#define DS_FEATURE_REPORT_CALIBRATION_SIZE 41 +#define DS_FEATURE_REPORT_PAIRING_INFO 0x09 +#define DS_FEATURE_REPORT_PAIRING_INFO_SIZE 20 +#define DS_FEATURE_REPORT_FIRMWARE_INFO 0x20 +#define DS_FEATURE_REPORT_FIRMWARE_INFO_SIZE 64 + +/* Button masks for DualSense input report. */ +#define DS_BUTTONS0_HAT_SWITCH GENMASK(3, 0) +#define DS_BUTTONS0_SQUARE BIT(4) +#define DS_BUTTONS0_CROSS BIT(5) +#define DS_BUTTONS0_CIRCLE BIT(6) +#define DS_BUTTONS0_TRIANGLE BIT(7) +#define DS_BUTTONS1_L1 BIT(0) +#define DS_BUTTONS1_R1 BIT(1) +#define DS_BUTTONS1_L2 BIT(2) +#define DS_BUTTONS1_R2 BIT(3) +#define DS_BUTTONS1_CREATE BIT(4) +#define DS_BUTTONS1_OPTIONS BIT(5) +#define DS_BUTTONS1_L3 BIT(6) +#define DS_BUTTONS1_R3 BIT(7) +#define DS_BUTTONS2_PS_HOME BIT(0) +#define DS_BUTTONS2_TOUCHPAD BIT(1) +#define DS_BUTTONS2_MIC_MUTE BIT(2) + +/* Status field of DualSense input report. */ +#define DS_STATUS_BATTERY_CAPACITY GENMASK(3, 0) +#define DS_STATUS_CHARGING GENMASK(7, 4) +#define DS_STATUS_CHARGING_SHIFT 4 + +/* + * Status of a DualSense touch point contact. + * Contact IDs, with highest bit set are 'inactive' + * and any associated data is then invalid. + */ +#define DS_TOUCH_POINT_INACTIVE BIT(7) + + /* Magic value required in tag field of Bluetooth output report. */ +#define DS_OUTPUT_TAG 0x10 +/* Flags for DualSense output report. */ +#define DS_OUTPUT_VALID_FLAG0_COMPATIBLE_VIBRATION BIT(0) +#define DS_OUTPUT_VALID_FLAG0_HAPTICS_SELECT BIT(1) +#define DS_OUTPUT_VALID_FLAG1_MIC_MUTE_LED_CONTROL_ENABLE BIT(0) +#define DS_OUTPUT_VALID_FLAG1_POWER_SAVE_CONTROL_ENABLE BIT(1) +#define DS_OUTPUT_VALID_FLAG1_LIGHTBAR_CONTROL_ENABLE BIT(2) +#define DS_OUTPUT_VALID_FLAG1_RELEASE_LEDS BIT(3) +#define DS_OUTPUT_VALID_FLAG1_PLAYER_INDICATOR_CONTROL_ENABLE BIT(4) +#define DS_OUTPUT_VALID_FLAG2_LIGHTBAR_SETUP_CONTROL_ENABLE BIT(1) +#define DS_OUTPUT_POWER_SAVE_CONTROL_MIC_MUTE BIT(4) +#define DS_OUTPUT_LIGHTBAR_SETUP_LIGHT_OUT BIT(1) + +/* DualSense hardware limits */ +#define DS_ACC_RES_PER_G 8192 +#define DS_ACC_RANGE (4*DS_ACC_RES_PER_G) +#define DS_GYRO_RES_PER_DEG_S 1024 +#define DS_GYRO_RANGE (2048*DS_GYRO_RES_PER_DEG_S) +#define DS_TOUCHPAD_WIDTH 1920 +#define DS_TOUCHPAD_HEIGHT 1080 + +struct dualsense { + struct ps_device base; + struct input_dev *gamepad; + struct input_dev *sensors; + struct input_dev *touchpad; + + /* Calibration data for accelerometer and gyroscope. */ + struct ps_calibration_data accel_calib_data[3]; + struct ps_calibration_data gyro_calib_data[3]; + + /* Timestamp for sensor data */ + bool sensor_timestamp_initialized; + uint32_t prev_sensor_timestamp; + uint32_t sensor_timestamp_us; + + /* Compatible rumble state */ + bool update_rumble; + uint8_t motor_left; + uint8_t motor_right; + + /* RGB lightbar */ + bool update_lightbar; + uint8_t lightbar_red; + uint8_t lightbar_green; + uint8_t lightbar_blue; + + /* Microphone */ + bool update_mic_mute; + bool mic_muted; + bool last_btn_mic_state; + + /* Player leds */ + bool update_player_leds; + uint8_t player_leds_state; + struct led_classdev player_leds[5]; + + struct work_struct output_worker; + void *output_report_dmabuf; + uint8_t output_seq; /* Sequence number for output report. */ +}; + +struct dualsense_touch_point { + uint8_t contact; + uint8_t x_lo; + uint8_t x_hi:4, y_lo:4; + uint8_t y_hi; +} __packed; +static_assert(sizeof(struct dualsense_touch_point) == 4); + +/* Main DualSense input report excluding any BT/USB specific headers. */ +struct dualsense_input_report { + uint8_t x, y; + uint8_t rx, ry; + uint8_t z, rz; + uint8_t seq_number; + uint8_t buttons[4]; + uint8_t reserved[4]; + + /* Motion sensors */ + __le16 gyro[3]; /* x, y, z */ + __le16 accel[3]; /* x, y, z */ + __le32 sensor_timestamp; + uint8_t reserved2; + + /* Touchpad */ + struct dualsense_touch_point points[2]; + + uint8_t reserved3[12]; + uint8_t status; + uint8_t reserved4[10]; +} __packed; +/* Common input report size shared equals the size of the USB report minus 1 byte for ReportID. */ +static_assert(sizeof(struct dualsense_input_report) == DS_INPUT_REPORT_USB_SIZE - 1); + +/* Common data between DualSense BT/USB main output report. */ +struct dualsense_output_report_common { + uint8_t valid_flag0; + uint8_t valid_flag1; + + /* For DualShock 4 compatibility mode. */ + uint8_t motor_right; + uint8_t motor_left; + + /* Audio controls */ + uint8_t reserved[4]; + uint8_t mute_button_led; + + uint8_t power_save_control; + uint8_t reserved2[28]; + + /* LEDs and lightbar */ + uint8_t valid_flag2; + uint8_t reserved3[2]; + uint8_t lightbar_setup; + uint8_t led_brightness; + uint8_t player_leds; + uint8_t lightbar_red; + uint8_t lightbar_green; + uint8_t lightbar_blue; +} __packed; +static_assert(sizeof(struct dualsense_output_report_common) == 47); + +struct dualsense_output_report_bt { + uint8_t report_id; /* 0x31 */ + uint8_t seq_tag; + uint8_t tag; + struct dualsense_output_report_common common; + uint8_t reserved[24]; + __le32 crc32; +} __packed; +static_assert(sizeof(struct dualsense_output_report_bt) == DS_OUTPUT_REPORT_BT_SIZE); + +struct dualsense_output_report_usb { + uint8_t report_id; /* 0x02 */ + struct dualsense_output_report_common common; + uint8_t reserved[15]; +} __packed; +static_assert(sizeof(struct dualsense_output_report_usb) == DS_OUTPUT_REPORT_USB_SIZE); + +/* + * The DualSense has a main output report used to control most features. It is + * largely the same between Bluetooth and USB except for different headers and CRC. + * This structure hide the differences between the two to simplify sending output reports. + */ +struct dualsense_output_report { + uint8_t *data; /* Start of data */ + uint8_t len; /* Size of output report */ + + /* Points to Bluetooth data payload in case for a Bluetooth report else NULL. */ + struct dualsense_output_report_bt *bt; + /* Points to USB data payload in case for a USB report else NULL. */ + struct dualsense_output_report_usb *usb; + /* Points to common section of report, so past any headers. */ + struct dualsense_output_report_common *common; +}; + +/* + * Common gamepad buttons across DualShock 3 / 4 and DualSense. + * Note: for device with a touchpad, touchpad button is not included + * as it will be part of the touchpad device. + */ +static const int ps_gamepad_buttons[] = { + BTN_WEST, /* Square */ + BTN_NORTH, /* Triangle */ + BTN_EAST, /* Circle */ + BTN_SOUTH, /* Cross */ + BTN_TL, /* L1 */ + BTN_TR, /* R1 */ + BTN_TL2, /* L2 */ + BTN_TR2, /* R2 */ + BTN_SELECT, /* Create (PS5) / Share (PS4) */ + BTN_START, /* Option */ + BTN_THUMBL, /* L3 */ + BTN_THUMBR, /* R3 */ + BTN_MODE, /* PS Home */ +}; + +static const struct {int x; int y; } ps_gamepad_hat_mapping[] = { + {0, -1}, {1, -1}, {1, 0}, {1, 1}, {0, 1}, {-1, 1}, {-1, 0}, {-1, -1}, + {0, 0}, +}; + +/* + * Add a new ps_device to ps_devices if it doesn't exist. + * Return error on duplicate device, which can happen if the same + * device is connected using both Bluetooth and USB. + */ +static int ps_devices_list_add(struct ps_device *dev) +{ + struct ps_device *entry; + + mutex_lock(&ps_devices_lock); + list_for_each_entry(entry, &ps_devices_list, list) { + if (!memcmp(entry->mac_address, dev->mac_address, sizeof(dev->mac_address))) { + hid_err(dev->hdev, "Duplicate device found for MAC address %pMR.\n", + dev->mac_address); + mutex_unlock(&ps_devices_lock); + return -EEXIST; + } + } + + list_add_tail(&dev->list, &ps_devices_list); + mutex_unlock(&ps_devices_lock); + return 0; +} + +static int ps_devices_list_remove(struct ps_device *dev) +{ + mutex_lock(&ps_devices_lock); + list_del(&dev->list); + mutex_unlock(&ps_devices_lock); + return 0; +} + +static int ps_device_set_player_id(struct ps_device *dev) +{ + int ret = ida_alloc(&ps_player_id_allocator, GFP_KERNEL); + + if (ret < 0) + return ret; + + dev->player_id = ret; + return 0; +} + +static void ps_device_release_player_id(struct ps_device *dev) +{ + ida_free(&ps_player_id_allocator, dev->player_id); + + dev->player_id = U32_MAX; +} + +static struct input_dev *ps_allocate_input_dev(struct hid_device *hdev, const char *name_suffix) +{ + struct input_dev *input_dev; + + input_dev = devm_input_allocate_device(&hdev->dev); + if (!input_dev) + return ERR_PTR(-ENOMEM); + + input_dev->id.bustype = hdev->bus; + input_dev->id.vendor = hdev->vendor; + input_dev->id.product = hdev->product; + input_dev->id.version = hdev->version; + input_dev->uniq = hdev->uniq; + + if (name_suffix) { + input_dev->name = devm_kasprintf(&hdev->dev, GFP_KERNEL, "%s %s", hdev->name, + name_suffix); + if (!input_dev->name) + return ERR_PTR(-ENOMEM); + } else { + input_dev->name = hdev->name; + } + + input_set_drvdata(input_dev, hdev); + + return input_dev; +} + +static enum power_supply_property ps_power_supply_props[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_PRESENT, + POWER_SUPPLY_PROP_CAPACITY, + POWER_SUPPLY_PROP_SCOPE, +}; + +static int ps_battery_get_property(struct power_supply *psy, + enum power_supply_property psp, + union power_supply_propval *val) +{ + struct ps_device *dev = power_supply_get_drvdata(psy); + uint8_t battery_capacity; + int battery_status; + unsigned long flags; + int ret = 0; + + spin_lock_irqsave(&dev->lock, flags); + battery_capacity = dev->battery_capacity; + battery_status = dev->battery_status; + spin_unlock_irqrestore(&dev->lock, flags); + + switch (psp) { + case POWER_SUPPLY_PROP_STATUS: + val->intval = battery_status; + break; + case POWER_SUPPLY_PROP_PRESENT: + val->intval = 1; + break; + case POWER_SUPPLY_PROP_CAPACITY: + val->intval = battery_capacity; + break; + case POWER_SUPPLY_PROP_SCOPE: + val->intval = POWER_SUPPLY_SCOPE_DEVICE; + break; + default: + ret = -EINVAL; + break; + } + + return ret; +} + +static int ps_device_register_battery(struct ps_device *dev) +{ + struct power_supply *battery; + struct power_supply_config battery_cfg = { .drv_data = dev }; + int ret; + + dev->battery_desc.type = POWER_SUPPLY_TYPE_BATTERY; + dev->battery_desc.properties = ps_power_supply_props; + dev->battery_desc.num_properties = ARRAY_SIZE(ps_power_supply_props); + dev->battery_desc.get_property = ps_battery_get_property; + dev->battery_desc.name = devm_kasprintf(&dev->hdev->dev, GFP_KERNEL, + "ps-controller-battery-%pMR", dev->mac_address); + if (!dev->battery_desc.name) + return -ENOMEM; + + battery = devm_power_supply_register(&dev->hdev->dev, &dev->battery_desc, &battery_cfg); + if (IS_ERR(battery)) { + ret = PTR_ERR(battery); + hid_err(dev->hdev, "Unable to register battery device: %d\n", ret); + return ret; + } + dev->battery = battery; + + ret = power_supply_powers(dev->battery, &dev->hdev->dev); + if (ret) { + hid_err(dev->hdev, "Unable to activate battery device: %d\n", ret); + return ret; + } + + return 0; +} + +/* Compute crc32 of HID data and compare against expected CRC. */ +static bool ps_check_crc32(uint8_t seed, uint8_t *data, size_t len, uint32_t report_crc) +{ + uint32_t crc; + + crc = crc32_le(0xFFFFFFFF, &seed, 1); + crc = ~crc32_le(crc, data, len); + + return crc == report_crc; +} + +static struct input_dev *ps_gamepad_create(struct hid_device *hdev, + int (*play_effect)(struct input_dev *, void *, struct ff_effect *)) +{ + struct input_dev *gamepad; + unsigned int i; + int ret; + + gamepad = ps_allocate_input_dev(hdev, NULL); + if (IS_ERR(gamepad)) + return ERR_CAST(gamepad); + + input_set_abs_params(gamepad, ABS_X, 0, 255, 0, 0); + input_set_abs_params(gamepad, ABS_Y, 0, 255, 0, 0); + input_set_abs_params(gamepad, ABS_Z, 0, 255, 0, 0); + input_set_abs_params(gamepad, ABS_RX, 0, 255, 0, 0); + input_set_abs_params(gamepad, ABS_RY, 0, 255, 0, 0); + input_set_abs_params(gamepad, ABS_RZ, 0, 255, 0, 0); + + input_set_abs_params(gamepad, ABS_HAT0X, -1, 1, 0, 0); + input_set_abs_params(gamepad, ABS_HAT0Y, -1, 1, 0, 0); + + for (i = 0; i < ARRAY_SIZE(ps_gamepad_buttons); i++) + input_set_capability(gamepad, EV_KEY, ps_gamepad_buttons[i]); + +#if IS_ENABLED(CONFIG_PLAYSTATION_FF) + if (play_effect) { + input_set_capability(gamepad, EV_FF, FF_RUMBLE); + input_ff_create_memless(gamepad, NULL, play_effect); + } +#endif + + ret = input_register_device(gamepad); + if (ret) + return ERR_PTR(ret); + + return gamepad; +} + +static int ps_get_report(struct hid_device *hdev, uint8_t report_id, uint8_t *buf, size_t size) +{ + int ret; + + ret = hid_hw_raw_request(hdev, report_id, buf, size, HID_FEATURE_REPORT, + HID_REQ_GET_REPORT); + if (ret < 0) { + hid_err(hdev, "Failed to retrieve feature with reportID %d: %d\n", report_id, ret); + return ret; + } + + if (ret != size) { + hid_err(hdev, "Invalid byte count transferred, expected %zu got %d\n", size, ret); + return -EINVAL; + } + + if (buf[0] != report_id) { + hid_err(hdev, "Invalid reportID received, expected %d got %d\n", report_id, buf[0]); + return -EINVAL; + } + + if (hdev->bus == BUS_BLUETOOTH) { + /* Last 4 bytes contains crc32. */ + uint8_t crc_offset = size - 4; + uint32_t report_crc = get_unaligned_le32(&buf[crc_offset]); + + if (!ps_check_crc32(PS_FEATURE_CRC32_SEED, buf, crc_offset, report_crc)) { + hid_err(hdev, "CRC check failed for reportID=%d\n", report_id); + return -EILSEQ; + } + } + + return 0; +} + +static struct input_dev *ps_sensors_create(struct hid_device *hdev, int accel_range, int accel_res, + int gyro_range, int gyro_res) +{ + struct input_dev *sensors; + int ret; + + sensors = ps_allocate_input_dev(hdev, "Motion Sensors"); + if (IS_ERR(sensors)) + return ERR_CAST(sensors); + + __set_bit(INPUT_PROP_ACCELEROMETER, sensors->propbit); + __set_bit(EV_MSC, sensors->evbit); + __set_bit(MSC_TIMESTAMP, sensors->mscbit); + + /* Accelerometer */ + input_set_abs_params(sensors, ABS_X, -accel_range, accel_range, 16, 0); + input_set_abs_params(sensors, ABS_Y, -accel_range, accel_range, 16, 0); + input_set_abs_params(sensors, ABS_Z, -accel_range, accel_range, 16, 0); + input_abs_set_res(sensors, ABS_X, accel_res); + input_abs_set_res(sensors, ABS_Y, accel_res); + input_abs_set_res(sensors, ABS_Z, accel_res); + + /* Gyroscope */ + input_set_abs_params(sensors, ABS_RX, -gyro_range, gyro_range, 16, 0); + input_set_abs_params(sensors, ABS_RY, -gyro_range, gyro_range, 16, 0); + input_set_abs_params(sensors, ABS_RZ, -gyro_range, gyro_range, 16, 0); + input_abs_set_res(sensors, ABS_RX, gyro_res); + input_abs_set_res(sensors, ABS_RY, gyro_res); + input_abs_set_res(sensors, ABS_RZ, gyro_res); + + ret = input_register_device(sensors); + if (ret) + return ERR_PTR(ret); + + return sensors; +} + +static struct input_dev *ps_touchpad_create(struct hid_device *hdev, int width, int height, + unsigned int num_contacts) +{ + struct input_dev *touchpad; + int ret; + + touchpad = ps_allocate_input_dev(hdev, "Touchpad"); + if (IS_ERR(touchpad)) + return ERR_CAST(touchpad); + + /* Map button underneath touchpad to BTN_LEFT. */ + input_set_capability(touchpad, EV_KEY, BTN_LEFT); + __set_bit(INPUT_PROP_BUTTONPAD, touchpad->propbit); + + input_set_abs_params(touchpad, ABS_MT_POSITION_X, 0, width - 1, 0, 0); + input_set_abs_params(touchpad, ABS_MT_POSITION_Y, 0, height - 1, 0, 0); + + ret = input_mt_init_slots(touchpad, num_contacts, INPUT_MT_POINTER); + if (ret) + return ERR_PTR(ret); + + ret = input_register_device(touchpad); + if (ret) + return ERR_PTR(ret); + + return touchpad; +} + +static ssize_t firmware_version_show(struct device *dev, + struct device_attribute + *attr, char *buf) +{ + struct hid_device *hdev = to_hid_device(dev); + struct ps_device *ps_dev = hid_get_drvdata(hdev); + + return sysfs_emit(buf, "0x%08x\n", ps_dev->fw_version); +} + +static DEVICE_ATTR_RO(firmware_version); + +static ssize_t hardware_version_show(struct device *dev, + struct device_attribute + *attr, char *buf) +{ + struct hid_device *hdev = to_hid_device(dev); + struct ps_device *ps_dev = hid_get_drvdata(hdev); + + return sysfs_emit(buf, "0x%08x\n", ps_dev->hw_version); +} + +static DEVICE_ATTR_RO(hardware_version); + +static struct attribute *ps_device_attributes[] = { + &dev_attr_firmware_version.attr, + &dev_attr_hardware_version.attr, + NULL +}; + +static const struct attribute_group ps_device_attribute_group = { + .attrs = ps_device_attributes, +}; + +static int dualsense_get_calibration_data(struct dualsense *ds) +{ + short gyro_pitch_bias, gyro_pitch_plus, gyro_pitch_minus; + short gyro_yaw_bias, gyro_yaw_plus, gyro_yaw_minus; + short gyro_roll_bias, gyro_roll_plus, gyro_roll_minus; + short gyro_speed_plus, gyro_speed_minus; + short acc_x_plus, acc_x_minus; + short acc_y_plus, acc_y_minus; + short acc_z_plus, acc_z_minus; + int speed_2x; + int range_2g; + int ret = 0; + uint8_t *buf; + + buf = kzalloc(DS_FEATURE_REPORT_CALIBRATION_SIZE, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + ret = ps_get_report(ds->base.hdev, DS_FEATURE_REPORT_CALIBRATION, buf, + DS_FEATURE_REPORT_CALIBRATION_SIZE); + if (ret) { + hid_err(ds->base.hdev, "Failed to retrieve DualSense calibration info: %d\n", ret); + goto err_free; + } + + gyro_pitch_bias = get_unaligned_le16(&buf[1]); + gyro_yaw_bias = get_unaligned_le16(&buf[3]); + gyro_roll_bias = get_unaligned_le16(&buf[5]); + gyro_pitch_plus = get_unaligned_le16(&buf[7]); + gyro_pitch_minus = get_unaligned_le16(&buf[9]); + gyro_yaw_plus = get_unaligned_le16(&buf[11]); + gyro_yaw_minus = get_unaligned_le16(&buf[13]); + gyro_roll_plus = get_unaligned_le16(&buf[15]); + gyro_roll_minus = get_unaligned_le16(&buf[17]); + gyro_speed_plus = get_unaligned_le16(&buf[19]); + gyro_speed_minus = get_unaligned_le16(&buf[21]); + acc_x_plus = get_unaligned_le16(&buf[23]); + acc_x_minus = get_unaligned_le16(&buf[25]); + acc_y_plus = get_unaligned_le16(&buf[27]); + acc_y_minus = get_unaligned_le16(&buf[29]); + acc_z_plus = get_unaligned_le16(&buf[31]); + acc_z_minus = get_unaligned_le16(&buf[33]); + + /* + * Set gyroscope calibration and normalization parameters. + * Data values will be normalized to 1/DS_GYRO_RES_PER_DEG_S degree/s. + */ + speed_2x = (gyro_speed_plus + gyro_speed_minus); + ds->gyro_calib_data[0].abs_code = ABS_RX; + ds->gyro_calib_data[0].bias = gyro_pitch_bias; + ds->gyro_calib_data[0].sens_numer = speed_2x*DS_GYRO_RES_PER_DEG_S; + ds->gyro_calib_data[0].sens_denom = gyro_pitch_plus - gyro_pitch_minus; + + ds->gyro_calib_data[1].abs_code = ABS_RY; + ds->gyro_calib_data[1].bias = gyro_yaw_bias; + ds->gyro_calib_data[1].sens_numer = speed_2x*DS_GYRO_RES_PER_DEG_S; + ds->gyro_calib_data[1].sens_denom = gyro_yaw_plus - gyro_yaw_minus; + + ds->gyro_calib_data[2].abs_code = ABS_RZ; + ds->gyro_calib_data[2].bias = gyro_roll_bias; + ds->gyro_calib_data[2].sens_numer = speed_2x*DS_GYRO_RES_PER_DEG_S; + ds->gyro_calib_data[2].sens_denom = gyro_roll_plus - gyro_roll_minus; + + /* + * Set accelerometer calibration and normalization parameters. + * Data values will be normalized to 1/DS_ACC_RES_PER_G g. + */ + range_2g = acc_x_plus - acc_x_minus; + ds->accel_calib_data[0].abs_code = ABS_X; + ds->accel_calib_data[0].bias = acc_x_plus - range_2g / 2; + ds->accel_calib_data[0].sens_numer = 2*DS_ACC_RES_PER_G; + ds->accel_calib_data[0].sens_denom = range_2g; + + range_2g = acc_y_plus - acc_y_minus; + ds->accel_calib_data[1].abs_code = ABS_Y; + ds->accel_calib_data[1].bias = acc_y_plus - range_2g / 2; + ds->accel_calib_data[1].sens_numer = 2*DS_ACC_RES_PER_G; + ds->accel_calib_data[1].sens_denom = range_2g; + + range_2g = acc_z_plus - acc_z_minus; + ds->accel_calib_data[2].abs_code = ABS_Z; + ds->accel_calib_data[2].bias = acc_z_plus - range_2g / 2; + ds->accel_calib_data[2].sens_numer = 2*DS_ACC_RES_PER_G; + ds->accel_calib_data[2].sens_denom = range_2g; + +err_free: + kfree(buf); + return ret; +} + +static int dualsense_get_firmware_info(struct dualsense *ds) +{ + uint8_t *buf; + int ret; + + buf = kzalloc(DS_FEATURE_REPORT_FIRMWARE_INFO_SIZE, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + ret = ps_get_report(ds->base.hdev, DS_FEATURE_REPORT_FIRMWARE_INFO, buf, + DS_FEATURE_REPORT_FIRMWARE_INFO_SIZE); + if (ret) { + hid_err(ds->base.hdev, "Failed to retrieve DualSense firmware info: %d\n", ret); + goto err_free; + } + + ds->base.hw_version = get_unaligned_le32(&buf[24]); + ds->base.fw_version = get_unaligned_le32(&buf[28]); + +err_free: + kfree(buf); + return ret; +} + +static int dualsense_get_mac_address(struct dualsense *ds) +{ + uint8_t *buf; + int ret = 0; + + buf = kzalloc(DS_FEATURE_REPORT_PAIRING_INFO_SIZE, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + ret = ps_get_report(ds->base.hdev, DS_FEATURE_REPORT_PAIRING_INFO, buf, + DS_FEATURE_REPORT_PAIRING_INFO_SIZE); + if (ret) { + hid_err(ds->base.hdev, "Failed to retrieve DualSense pairing info: %d\n", ret); + goto err_free; + } + + memcpy(ds->base.mac_address, &buf[1], sizeof(ds->base.mac_address)); + +err_free: + kfree(buf); + return ret; +} + +static void dualsense_init_output_report(struct dualsense *ds, struct dualsense_output_report *rp, + void *buf) +{ + struct hid_device *hdev = ds->base.hdev; + + if (hdev->bus == BUS_BLUETOOTH) { + struct dualsense_output_report_bt *bt = buf; + + memset(bt, 0, sizeof(*bt)); + bt->report_id = DS_OUTPUT_REPORT_BT; + bt->tag = DS_OUTPUT_TAG; /* Tag must be set. Exact meaning is unclear. */ + + /* + * Highest 4-bit is a sequence number, which needs to be increased + * every report. Lowest 4-bit is tag and can be zero for now. + */ + bt->seq_tag = (ds->output_seq << 4) | 0x0; + if (++ds->output_seq == 16) + ds->output_seq = 0; + + rp->data = buf; + rp->len = sizeof(*bt); + rp->bt = bt; + rp->usb = NULL; + rp->common = &bt->common; + } else { /* USB */ + struct dualsense_output_report_usb *usb = buf; + + memset(usb, 0, sizeof(*usb)); + usb->report_id = DS_OUTPUT_REPORT_USB; + + rp->data = buf; + rp->len = sizeof(*usb); + rp->bt = NULL; + rp->usb = usb; + rp->common = &usb->common; + } +} + +/* + * Helper function to send DualSense output reports. Applies a CRC at the end of a report + * for Bluetooth reports. + */ +static void dualsense_send_output_report(struct dualsense *ds, + struct dualsense_output_report *report) +{ + struct hid_device *hdev = ds->base.hdev; + + /* Bluetooth packets need to be signed with a CRC in the last 4 bytes. */ + if (report->bt) { + uint32_t crc; + uint8_t seed = PS_OUTPUT_CRC32_SEED; + + crc = crc32_le(0xFFFFFFFF, &seed, 1); + crc = ~crc32_le(crc, report->data, report->len - 4); + + report->bt->crc32 = cpu_to_le32(crc); + } + + hid_hw_output_report(hdev, report->data, report->len); +} + +static void dualsense_output_worker(struct work_struct *work) +{ + struct dualsense *ds = container_of(work, struct dualsense, output_worker); + struct dualsense_output_report report; + struct dualsense_output_report_common *common; + unsigned long flags; + + dualsense_init_output_report(ds, &report, ds->output_report_dmabuf); + common = report.common; + + spin_lock_irqsave(&ds->base.lock, flags); + + if (ds->update_rumble) { + /* Select classic rumble style haptics and enable it. */ + common->valid_flag0 |= DS_OUTPUT_VALID_FLAG0_HAPTICS_SELECT; + common->valid_flag0 |= DS_OUTPUT_VALID_FLAG0_COMPATIBLE_VIBRATION; + common->motor_left = ds->motor_left; + common->motor_right = ds->motor_right; + ds->update_rumble = false; + } + + if (ds->update_lightbar) { + common->valid_flag1 |= DS_OUTPUT_VALID_FLAG1_LIGHTBAR_CONTROL_ENABLE; + common->lightbar_red = ds->lightbar_red; + common->lightbar_green = ds->lightbar_green; + common->lightbar_blue = ds->lightbar_blue; + + ds->update_lightbar = false; + } + + if (ds->update_player_leds) { + common->valid_flag1 |= DS_OUTPUT_VALID_FLAG1_PLAYER_INDICATOR_CONTROL_ENABLE; + common->player_leds = ds->player_leds_state; + + ds->update_player_leds = false; + } + + if (ds->update_mic_mute) { + common->valid_flag1 |= DS_OUTPUT_VALID_FLAG1_MIC_MUTE_LED_CONTROL_ENABLE; + common->mute_button_led = ds->mic_muted; + + if (ds->mic_muted) { + /* Disable microphone */ + common->valid_flag1 |= DS_OUTPUT_VALID_FLAG1_POWER_SAVE_CONTROL_ENABLE; + common->power_save_control |= DS_OUTPUT_POWER_SAVE_CONTROL_MIC_MUTE; + } else { + /* Enable microphone */ + common->valid_flag1 |= DS_OUTPUT_VALID_FLAG1_POWER_SAVE_CONTROL_ENABLE; + common->power_save_control &= ~DS_OUTPUT_POWER_SAVE_CONTROL_MIC_MUTE; + } + + ds->update_mic_mute = false; + } + + spin_unlock_irqrestore(&ds->base.lock, flags); + + dualsense_send_output_report(ds, &report); +} + +static int dualsense_parse_report(struct ps_device *ps_dev, struct hid_report *report, + u8 *data, int size) +{ + struct hid_device *hdev = ps_dev->hdev; + struct dualsense *ds = container_of(ps_dev, struct dualsense, base); + struct dualsense_input_report *ds_report; + uint8_t battery_data, battery_capacity, charging_status, value; + int battery_status; + uint32_t sensor_timestamp; + bool btn_mic_state; + unsigned long flags; + int i; + + /* + * DualSense in USB uses the full HID report for reportID 1, but + * Bluetooth uses a minimal HID report for reportID 1 and reports + * the full report using reportID 49. + */ + if (hdev->bus == BUS_USB && report->id == DS_INPUT_REPORT_USB && + size == DS_INPUT_REPORT_USB_SIZE) { + ds_report = (struct dualsense_input_report *)&data[1]; + } else if (hdev->bus == BUS_BLUETOOTH && report->id == DS_INPUT_REPORT_BT && + size == DS_INPUT_REPORT_BT_SIZE) { + /* Last 4 bytes of input report contain crc32 */ + uint32_t report_crc = get_unaligned_le32(&data[size - 4]); + + if (!ps_check_crc32(PS_INPUT_CRC32_SEED, data, size - 4, report_crc)) { + hid_err(hdev, "DualSense input CRC's check failed\n"); + return -EILSEQ; + } + + ds_report = (struct dualsense_input_report *)&data[2]; + } else { + hid_err(hdev, "Unhandled reportID=%d\n", report->id); + return -1; + } + + input_report_abs(ds->gamepad, ABS_X, ds_report->x); + input_report_abs(ds->gamepad, ABS_Y, ds_report->y); + input_report_abs(ds->gamepad, ABS_RX, ds_report->rx); + input_report_abs(ds->gamepad, ABS_RY, ds_report->ry); + input_report_abs(ds->gamepad, ABS_Z, ds_report->z); + input_report_abs(ds->gamepad, ABS_RZ, ds_report->rz); + + value = ds_report->buttons[0] & DS_BUTTONS0_HAT_SWITCH; + if (value >= ARRAY_SIZE(ps_gamepad_hat_mapping)) + value = 8; /* center */ + input_report_abs(ds->gamepad, ABS_HAT0X, ps_gamepad_hat_mapping[value].x); + input_report_abs(ds->gamepad, ABS_HAT0Y, ps_gamepad_hat_mapping[value].y); + + input_report_key(ds->gamepad, BTN_WEST, ds_report->buttons[0] & DS_BUTTONS0_SQUARE); + input_report_key(ds->gamepad, BTN_SOUTH, ds_report->buttons[0] & DS_BUTTONS0_CROSS); + input_report_key(ds->gamepad, BTN_EAST, ds_report->buttons[0] & DS_BUTTONS0_CIRCLE); + input_report_key(ds->gamepad, BTN_NORTH, ds_report->buttons[0] & DS_BUTTONS0_TRIANGLE); + input_report_key(ds->gamepad, BTN_TL, ds_report->buttons[1] & DS_BUTTONS1_L1); + input_report_key(ds->gamepad, BTN_TR, ds_report->buttons[1] & DS_BUTTONS1_R1); + input_report_key(ds->gamepad, BTN_TL2, ds_report->buttons[1] & DS_BUTTONS1_L2); + input_report_key(ds->gamepad, BTN_TR2, ds_report->buttons[1] & DS_BUTTONS1_R2); + input_report_key(ds->gamepad, BTN_SELECT, ds_report->buttons[1] & DS_BUTTONS1_CREATE); + input_report_key(ds->gamepad, BTN_START, ds_report->buttons[1] & DS_BUTTONS1_OPTIONS); + input_report_key(ds->gamepad, BTN_THUMBL, ds_report->buttons[1] & DS_BUTTONS1_L3); + input_report_key(ds->gamepad, BTN_THUMBR, ds_report->buttons[1] & DS_BUTTONS1_R3); + input_report_key(ds->gamepad, BTN_MODE, ds_report->buttons[2] & DS_BUTTONS2_PS_HOME); + input_sync(ds->gamepad); + + /* + * The DualSense has an internal microphone, which can be muted through a mute button + * on the device. The driver is expected to read the button state and program the device + * to mute/unmute audio at the hardware level. + */ + btn_mic_state = !!(ds_report->buttons[2] & DS_BUTTONS2_MIC_MUTE); + if (btn_mic_state && !ds->last_btn_mic_state) { + spin_lock_irqsave(&ps_dev->lock, flags); + ds->update_mic_mute = true; + ds->mic_muted = !ds->mic_muted; /* toggle */ + spin_unlock_irqrestore(&ps_dev->lock, flags); + + /* Schedule updating of microphone state at hardware level. */ + schedule_work(&ds->output_worker); + } + ds->last_btn_mic_state = btn_mic_state; + + /* Parse and calibrate gyroscope data. */ + for (i = 0; i < ARRAY_SIZE(ds_report->gyro); i++) { + int raw_data = (short)le16_to_cpu(ds_report->gyro[i]); + int calib_data = mult_frac(ds->gyro_calib_data[i].sens_numer, + raw_data - ds->gyro_calib_data[i].bias, + ds->gyro_calib_data[i].sens_denom); + + input_report_abs(ds->sensors, ds->gyro_calib_data[i].abs_code, calib_data); + } + + /* Parse and calibrate accelerometer data. */ + for (i = 0; i < ARRAY_SIZE(ds_report->accel); i++) { + int raw_data = (short)le16_to_cpu(ds_report->accel[i]); + int calib_data = mult_frac(ds->accel_calib_data[i].sens_numer, + raw_data - ds->accel_calib_data[i].bias, + ds->accel_calib_data[i].sens_denom); + + input_report_abs(ds->sensors, ds->accel_calib_data[i].abs_code, calib_data); + } + + /* Convert timestamp (in 0.33us unit) to timestamp_us */ + sensor_timestamp = le32_to_cpu(ds_report->sensor_timestamp); + if (!ds->sensor_timestamp_initialized) { + ds->sensor_timestamp_us = DIV_ROUND_CLOSEST(sensor_timestamp, 3); + ds->sensor_timestamp_initialized = true; + } else { + uint32_t delta; + + if (ds->prev_sensor_timestamp > sensor_timestamp) + delta = (U32_MAX - ds->prev_sensor_timestamp + sensor_timestamp + 1); + else + delta = sensor_timestamp - ds->prev_sensor_timestamp; + ds->sensor_timestamp_us += DIV_ROUND_CLOSEST(delta, 3); + } + ds->prev_sensor_timestamp = sensor_timestamp; + input_event(ds->sensors, EV_MSC, MSC_TIMESTAMP, ds->sensor_timestamp_us); + input_sync(ds->sensors); + + for (i = 0; i < ARRAY_SIZE(ds_report->points); i++) { + struct dualsense_touch_point *point = &ds_report->points[i]; + bool active = (point->contact & DS_TOUCH_POINT_INACTIVE) ? false : true; + + input_mt_slot(ds->touchpad, i); + input_mt_report_slot_state(ds->touchpad, MT_TOOL_FINGER, active); + + if (active) { + int x = (point->x_hi << 8) | point->x_lo; + int y = (point->y_hi << 4) | point->y_lo; + + input_report_abs(ds->touchpad, ABS_MT_POSITION_X, x); + input_report_abs(ds->touchpad, ABS_MT_POSITION_Y, y); + } + } + input_mt_sync_frame(ds->touchpad); + input_report_key(ds->touchpad, BTN_LEFT, ds_report->buttons[2] & DS_BUTTONS2_TOUCHPAD); + input_sync(ds->touchpad); + + battery_data = ds_report->status & DS_STATUS_BATTERY_CAPACITY; + charging_status = (ds_report->status & DS_STATUS_CHARGING) >> DS_STATUS_CHARGING_SHIFT; + + switch (charging_status) { + case 0x0: + /* + * Each unit of battery data corresponds to 10% + * 0 = 0-9%, 1 = 10-19%, .. and 10 = 100% + */ + battery_capacity = min(battery_data * 10 + 5, 100); + battery_status = POWER_SUPPLY_STATUS_DISCHARGING; + break; + case 0x1: + battery_capacity = min(battery_data * 10 + 5, 100); + battery_status = POWER_SUPPLY_STATUS_CHARGING; + break; + case 0x2: + battery_capacity = 100; + battery_status = POWER_SUPPLY_STATUS_FULL; + break; + case 0xa: /* voltage or temperature out of range */ + case 0xb: /* temperature error */ + battery_capacity = 0; + battery_status = POWER_SUPPLY_STATUS_NOT_CHARGING; + break; + case 0xf: /* charging error */ + default: + battery_capacity = 0; + battery_status = POWER_SUPPLY_STATUS_UNKNOWN; + } + + spin_lock_irqsave(&ps_dev->lock, flags); + ps_dev->battery_capacity = battery_capacity; + ps_dev->battery_status = battery_status; + spin_unlock_irqrestore(&ps_dev->lock, flags); + + return 0; +} + +static int dualsense_play_effect(struct input_dev *dev, void *data, struct ff_effect *effect) +{ + struct hid_device *hdev = input_get_drvdata(dev); + struct dualsense *ds = hid_get_drvdata(hdev); + unsigned long flags; + + if (effect->type != FF_RUMBLE) + return 0; + + spin_lock_irqsave(&ds->base.lock, flags); + ds->update_rumble = true; + ds->motor_left = effect->u.rumble.strong_magnitude / 256; + ds->motor_right = effect->u.rumble.weak_magnitude / 256; + spin_unlock_irqrestore(&ds->base.lock, flags); + + schedule_work(&ds->output_worker); + return 0; +} + +static int dualsense_reset_leds(struct dualsense *ds) +{ + struct dualsense_output_report report; + uint8_t *buf; + + buf = kzalloc(sizeof(struct dualsense_output_report_bt), GFP_KERNEL); + if (!buf) + return -ENOMEM; + + dualsense_init_output_report(ds, &report, buf); + /* + * On Bluetooth the DualSense outputs an animation on the lightbar + * during startup and maintains a color afterwards. We need to explicitly + * reconfigure the lightbar before we can do any programming later on. + * In USB the lightbar is not on by default, but redoing the setup there + * doesn't hurt. + */ + report.common->valid_flag2 = DS_OUTPUT_VALID_FLAG2_LIGHTBAR_SETUP_CONTROL_ENABLE; + report.common->lightbar_setup = DS_OUTPUT_LIGHTBAR_SETUP_LIGHT_OUT; /* Fade light out. */ + dualsense_send_output_report(ds, &report); + + kfree(buf); + return 0; +} + +static void dualsense_set_lightbar(struct dualsense *ds, uint8_t red, uint8_t green, uint8_t blue) +{ + ds->update_lightbar = true; + ds->lightbar_red = red; + ds->lightbar_green = green; + ds->lightbar_blue = blue; + + schedule_work(&ds->output_worker); +} + +static void dualsense_set_player_leds(struct dualsense *ds) +{ + /* + * The DualSense controller has a row of 5 LEDs used for player ids. + * Behavior on the PlayStation 5 console is to center the player id + * across the LEDs, so e.g. player 1 would be "--x--" with x being 'on'. + * Follow a similar mapping here. + */ + static const int player_ids[5] = { + BIT(2), + BIT(3) | BIT(1), + BIT(4) | BIT(2) | BIT(0), + BIT(4) | BIT(3) | BIT(1) | BIT(0), + BIT(4) | BIT(3) | BIT(2) | BIT(1) | BIT(0) + }; + + uint8_t player_id = ds->base.player_id % ARRAY_SIZE(player_ids); + + ds->update_player_leds = true; + ds->player_leds_state = player_ids[player_id]; + schedule_work(&ds->output_worker); +} + +static struct ps_device *dualsense_create(struct hid_device *hdev) +{ + struct dualsense *ds; + struct ps_device *ps_dev; + uint8_t max_output_report_size; + int ret; + + ds = devm_kzalloc(&hdev->dev, sizeof(*ds), GFP_KERNEL); + if (!ds) + return ERR_PTR(-ENOMEM); + + /* + * Patch version to allow userspace to distinguish between + * hid-generic vs hid-playstation axis and button mapping. + */ + hdev->version |= HID_PLAYSTATION_VERSION_PATCH; + + ps_dev = &ds->base; + ps_dev->hdev = hdev; + spin_lock_init(&ps_dev->lock); + ps_dev->battery_capacity = 100; /* initial value until parse_report. */ + ps_dev->battery_status = POWER_SUPPLY_STATUS_UNKNOWN; + ps_dev->parse_report = dualsense_parse_report; + INIT_WORK(&ds->output_worker, dualsense_output_worker); + hid_set_drvdata(hdev, ds); + + max_output_report_size = sizeof(struct dualsense_output_report_bt); + ds->output_report_dmabuf = devm_kzalloc(&hdev->dev, max_output_report_size, GFP_KERNEL); + if (!ds->output_report_dmabuf) + return ERR_PTR(-ENOMEM); + + ret = dualsense_get_mac_address(ds); + if (ret) { + hid_err(hdev, "Failed to get MAC address from DualSense\n"); + return ERR_PTR(ret); + } + snprintf(hdev->uniq, sizeof(hdev->uniq), "%pMR", ds->base.mac_address); + + ret = dualsense_get_firmware_info(ds); + if (ret) { + hid_err(hdev, "Failed to get firmware info from DualSense\n"); + return ERR_PTR(ret); + } + + ret = ps_devices_list_add(ps_dev); + if (ret) + return ERR_PTR(ret); + + ret = dualsense_get_calibration_data(ds); + if (ret) { + hid_err(hdev, "Failed to get calibration data from DualSense\n"); + goto err; + } + + ds->gamepad = ps_gamepad_create(hdev, dualsense_play_effect); + if (IS_ERR(ds->gamepad)) { + ret = PTR_ERR(ds->gamepad); + goto err; + } + + ds->sensors = ps_sensors_create(hdev, DS_ACC_RANGE, DS_ACC_RES_PER_G, + DS_GYRO_RANGE, DS_GYRO_RES_PER_DEG_S); + if (IS_ERR(ds->sensors)) { + ret = PTR_ERR(ds->sensors); + goto err; + } + + ds->touchpad = ps_touchpad_create(hdev, DS_TOUCHPAD_WIDTH, DS_TOUCHPAD_HEIGHT, 2); + if (IS_ERR(ds->touchpad)) { + ret = PTR_ERR(ds->touchpad); + goto err; + } + + ret = ps_device_register_battery(ps_dev); + if (ret) + goto err; + + /* + * The hardware may have control over the LEDs (e.g. in Bluetooth on startup). + * Reset the LEDs (lightbar, mute, player leds), so we can control them + * from software. + */ + ret = dualsense_reset_leds(ds); + if (ret) + goto err; + + dualsense_set_lightbar(ds, 0, 0, 128); /* blue */ + + ret = ps_device_set_player_id(ps_dev); + if (ret) { + hid_err(hdev, "Failed to assign player id for DualSense: %d\n", ret); + goto err; + } + + /* Set player LEDs to our player id. */ + dualsense_set_player_leds(ds); + + /* + * Reporting hardware and firmware is important as there are frequent updates, which + * can change behavior. + */ + hid_info(hdev, "Registered DualSense controller hw_version=0x%08x fw_version=0x%08x\n", + ds->base.hw_version, ds->base.fw_version); + + return &ds->base; + +err: + ps_devices_list_remove(ps_dev); + return ERR_PTR(ret); +} + +static int ps_raw_event(struct hid_device *hdev, struct hid_report *report, + u8 *data, int size) +{ + struct ps_device *dev = hid_get_drvdata(hdev); + + if (dev && dev->parse_report) + return dev->parse_report(dev, report, data, size); + + return 0; +} + +static int ps_probe(struct hid_device *hdev, const struct hid_device_id *id) +{ + struct ps_device *dev; + int ret; + + ret = hid_parse(hdev); + if (ret) { + hid_err(hdev, "Parse failed\n"); + return ret; + } + + ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW); + if (ret) { + hid_err(hdev, "Failed to start HID device\n"); + return ret; + } + + ret = hid_hw_open(hdev); + if (ret) { + hid_err(hdev, "Failed to open HID device\n"); + goto err_stop; + } + + if (hdev->product == USB_DEVICE_ID_SONY_PS5_CONTROLLER) { + dev = dualsense_create(hdev); + if (IS_ERR(dev)) { + hid_err(hdev, "Failed to create dualsense.\n"); + ret = PTR_ERR(dev); + goto err_close; + } + } + + ret = devm_device_add_group(&hdev->dev, &ps_device_attribute_group); + if (ret) { + hid_err(hdev, "Failed to register sysfs nodes.\n"); + goto err_close; + } + + return ret; + +err_close: + hid_hw_close(hdev); +err_stop: + hid_hw_stop(hdev); + return ret; +} + +static void ps_remove(struct hid_device *hdev) +{ + struct ps_device *dev = hid_get_drvdata(hdev); + + ps_devices_list_remove(dev); + ps_device_release_player_id(dev); + + hid_hw_close(hdev); + hid_hw_stop(hdev); +} + +static const struct hid_device_id ps_devices[] = { + { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS5_CONTROLLER) }, + { HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS5_CONTROLLER) }, + { } +}; +MODULE_DEVICE_TABLE(hid, ps_devices); + +static struct hid_driver ps_driver = { + .name = "playstation", + .id_table = ps_devices, + .probe = ps_probe, + .remove = ps_remove, + .raw_event = ps_raw_event, +}; + +static int __init ps_init(void) +{ + return hid_register_driver(&ps_driver); +} + +static void __exit ps_exit(void) +{ + hid_unregister_driver(&ps_driver); + ida_destroy(&ps_player_id_allocator); +} + +module_init(ps_init); +module_exit(ps_exit); + +MODULE_AUTHOR("Sony Interactive Entertainment"); +MODULE_DESCRIPTION("HID Driver for PlayStation peripherals."); +MODULE_LICENSE("GPL"); diff --git a/drivers/hid/hid-quirks.c b/drivers/hid/hid-quirks.c index d9ca874dffac..1a9daf03dbfa 100644 --- a/drivers/hid/hid-quirks.c +++ b/drivers/hid/hid-quirks.c @@ -180,7 +180,6 @@ static const struct hid_device_id hid_quirks[] = { { HID_USB_DEVICE(USB_VENDOR_ID_TOUCHPACK, USB_DEVICE_ID_TOUCHPACK_RTS), HID_QUIRK_MULTI_INPUT }, { HID_USB_DEVICE(USB_VENDOR_ID_TPV, USB_DEVICE_ID_TPV_OPTICAL_TOUCHSCREEN_8882), HID_QUIRK_NOGET }, { HID_USB_DEVICE(USB_VENDOR_ID_TPV, USB_DEVICE_ID_TPV_OPTICAL_TOUCHSCREEN_8883), HID_QUIRK_NOGET }, - { HID_USB_DEVICE(USB_VENDOR_ID_TRUST, USB_DEVICE_ID_TRUST_PANORA_TABLET), HID_QUIRK_MULTI_INPUT | HID_QUIRK_HIDINPUT_FORCE }, { HID_USB_DEVICE(USB_VENDOR_ID_TURBOX, USB_DEVICE_ID_TURBOX_KEYBOARD), HID_QUIRK_NOGET }, { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UCLOGIC_TABLET_KNA5), HID_QUIRK_MULTI_INPUT }, { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UCLOGIC_TABLET_TWA60), HID_QUIRK_MULTI_INPUT }, @@ -1029,7 +1028,7 @@ static DEFINE_MUTEX(dquirks_lock); /* Runtime ("dynamic") quirks manipulation functions */ /** - * hid_exists_dquirk: find any dynamic quirks for a HID device + * hid_exists_dquirk - find any dynamic quirks for a HID device * @hdev: the HID device to match * * Description: @@ -1037,7 +1036,7 @@ static DEFINE_MUTEX(dquirks_lock); * the pointer to the relevant struct hid_device_id if found. * Must be called with a read lock held on dquirks_lock. * - * Returns: NULL if no quirk found, struct hid_device_id * if found. + * Return: NULL if no quirk found, struct hid_device_id * if found. */ static struct hid_device_id *hid_exists_dquirk(const struct hid_device *hdev) { @@ -1061,7 +1060,7 @@ static struct hid_device_id *hid_exists_dquirk(const struct hid_device *hdev) /** - * hid_modify_dquirk: add/replace a HID quirk + * hid_modify_dquirk - add/replace a HID quirk * @id: the HID device to match * @quirks: the unsigned long quirks value to add/replace * @@ -1070,7 +1069,7 @@ static struct hid_device_id *hid_exists_dquirk(const struct hid_device *hdev) * quirks value with what was provided. Otherwise, add the quirk * to the dynamic quirks list. * - * Returns: 0 OK, -error on failure. + * Return: 0 OK, -error on failure. */ static int hid_modify_dquirk(const struct hid_device_id *id, const unsigned long quirks) @@ -1122,7 +1121,7 @@ static int hid_modify_dquirk(const struct hid_device_id *id, } /** - * hid_remove_all_dquirks: remove all runtime HID quirks from memory + * hid_remove_all_dquirks - remove all runtime HID quirks from memory * @bus: bus to match against. Use HID_BUS_ANY if all need to be removed. * * Description: @@ -1146,7 +1145,10 @@ static void hid_remove_all_dquirks(__u16 bus) } /** - * hid_quirks_init: apply HID quirks specified at module load time + * hid_quirks_init - apply HID quirks specified at module load time + * @quirks_param: array of quirks strings (vendor:product:quirks) + * @bus: bus type + * @count: number of quirks to check */ int hid_quirks_init(char **quirks_param, __u16 bus, int count) { @@ -1177,7 +1179,7 @@ int hid_quirks_init(char **quirks_param, __u16 bus, int count) EXPORT_SYMBOL_GPL(hid_quirks_init); /** - * hid_quirks_exit: release memory associated with dynamic_quirks + * hid_quirks_exit - release memory associated with dynamic_quirks * @bus: a bus to match against * * Description: @@ -1194,14 +1196,14 @@ void hid_quirks_exit(__u16 bus) EXPORT_SYMBOL_GPL(hid_quirks_exit); /** - * hid_gets_squirk: return any static quirks for a HID device + * hid_gets_squirk - return any static quirks for a HID device * @hdev: the HID device to match * * Description: * Given a HID device, return a pointer to the quirked hid_device_id entry * associated with that device. * - * Returns: the quirks. + * Return: the quirks. */ static unsigned long hid_gets_squirk(const struct hid_device *hdev) { @@ -1225,13 +1227,13 @@ static unsigned long hid_gets_squirk(const struct hid_device *hdev) } /** - * hid_lookup_quirk: return any quirks associated with a HID device + * hid_lookup_quirk - return any quirks associated with a HID device * @hdev: the HID device to look for * * Description: * Given a HID device, return any quirks associated with that device. * - * Returns: an unsigned long quirks value. + * Return: an unsigned long quirks value. */ unsigned long hid_lookup_quirk(const struct hid_device *hdev) { diff --git a/drivers/hid/hid-roccat-arvo.c b/drivers/hid/hid-roccat-arvo.c index ffcd444ae2ba..4556d2a50f75 100644 --- a/drivers/hid/hid-roccat-arvo.c +++ b/drivers/hid/hid-roccat-arvo.c @@ -42,7 +42,7 @@ static ssize_t arvo_sysfs_show_mode_key(struct device *dev, if (retval) return retval; - return snprintf(buf, PAGE_SIZE, "%d\n", temp_buf.state); + return sysfs_emit(buf, "%d\n", temp_buf.state); } static ssize_t arvo_sysfs_set_mode_key(struct device *dev, @@ -92,7 +92,7 @@ static ssize_t arvo_sysfs_show_key_mask(struct device *dev, if (retval) return retval; - return snprintf(buf, PAGE_SIZE, "%d\n", temp_buf.key_mask); + return sysfs_emit(buf, "%d\n", temp_buf.key_mask); } static ssize_t arvo_sysfs_set_key_mask(struct device *dev, @@ -146,7 +146,7 @@ static ssize_t arvo_sysfs_show_actual_profile(struct device *dev, struct arvo_device *arvo = hid_get_drvdata(dev_get_drvdata(dev->parent->parent)); - return snprintf(buf, PAGE_SIZE, "%d\n", arvo->actual_profile); + return sysfs_emit(buf, "%d\n", arvo->actual_profile); } static ssize_t arvo_sysfs_set_actual_profile(struct device *dev, diff --git a/drivers/hid/hid-sony.c b/drivers/hid/hid-sony.c index e3a557dc9ffd..8319b0ce385a 100644 --- a/drivers/hid/hid-sony.c +++ b/drivers/hid/hid-sony.c @@ -12,6 +12,7 @@ * Copyright (c) 2014-2016 Frank Praznik <frank.praznik@gmail.com> * Copyright (c) 2018 Todd Kelner * Copyright (c) 2020 Pascal Giard <pascal.giard@etsmtl.ca> + * Copyright (c) 2020 Sanjay Govind <sanjay.govind9@gmail.com> */ /* @@ -59,7 +60,8 @@ #define NSG_MR5U_REMOTE_BT BIT(14) #define NSG_MR7U_REMOTE_BT BIT(15) #define SHANWAN_GAMEPAD BIT(16) -#define GHL_GUITAR_PS3WIIU BIT(17) +#define GH_GUITAR_CONTROLLER BIT(17) +#define GHL_GUITAR_PS3WIIU BIT(18) #define SIXAXIS_CONTROLLER (SIXAXIS_CONTROLLER_USB | SIXAXIS_CONTROLLER_BT) #define MOTION_CONTROLLER (MOTION_CONTROLLER_USB | MOTION_CONTROLLER_BT) @@ -84,7 +86,7 @@ #define NSG_MRXU_MAX_Y 1868 #define GHL_GUITAR_POKE_INTERVAL 10 /* In seconds */ -#define GHL_GUITAR_TILT_USAGE 44 +#define GUITAR_TILT_USAGE 44 /* Magic value and data taken from GHLtarUtility: * https://github.com/ghlre/GHLtarUtility/blob/master/PS3Guitar.cs @@ -692,7 +694,7 @@ static int guitar_mapping(struct hid_device *hdev, struct hid_input *hi, if ((usage->hid & HID_USAGE_PAGE) == HID_UP_MSVENDOR) { unsigned int abs = usage->hid & HID_USAGE; - if (abs == GHL_GUITAR_TILT_USAGE) { + if (abs == GUITAR_TILT_USAGE) { hid_map_usage_clear(hi, usage, bit, max, EV_ABS, ABS_RY); return 1; } @@ -1481,7 +1483,7 @@ static int sony_mapping(struct hid_device *hdev, struct hid_input *hi, if (sc->quirks & DUALSHOCK4_CONTROLLER) return ds4_mapping(hdev, hi, field, usage, bit, max); - if (sc->quirks & GHL_GUITAR_PS3WIIU) + if (sc->quirks & GH_GUITAR_CONTROLLER) return guitar_mapping(hdev, hi, field, usage, bit, max); /* Let hid-core decide for the others */ @@ -3167,8 +3169,14 @@ static const struct hid_device_id sony_devices[] = { { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_SMK, USB_DEVICE_ID_SMK_NSG_MR7U_REMOTE), .driver_data = NSG_MR7U_REMOTE_BT }, /* Guitar Hero Live PS3 and Wii U guitar dongles */ - { HID_USB_DEVICE(USB_VENDOR_ID_SONY_GHLIVE, USB_DEVICE_ID_SONY_PS3WIIU_GHLIVE_DONGLE), - .driver_data = GHL_GUITAR_PS3WIIU}, + { HID_USB_DEVICE(USB_VENDOR_ID_SONY_RHYTHM, USB_DEVICE_ID_SONY_PS3WIIU_GHLIVE_DONGLE), + .driver_data = GHL_GUITAR_PS3WIIU | GH_GUITAR_CONTROLLER }, + /* Guitar Hero PC Guitar Dongle */ + { HID_USB_DEVICE(USB_VENDOR_ID_ACTIVISION, USB_DEVICE_ID_ACTIVISION_GUITAR_DONGLE), + .driver_data = GH_GUITAR_CONTROLLER }, + /* Guitar Hero PS3 World Tour Guitar Dongle */ + { HID_USB_DEVICE(USB_VENDOR_ID_SONY_RHYTHM, USB_DEVICE_ID_SONY_PS3_GUITAR_DONGLE), + .driver_data = GH_GUITAR_CONTROLLER }, { } }; MODULE_DEVICE_TABLE(hid, sony_devices); diff --git a/drivers/hid/hid-uclogic-core.c b/drivers/hid/hid-uclogic-core.c index 8e9c9e646cb7..6a9865dd703c 100644 --- a/drivers/hid/hid-uclogic-core.c +++ b/drivers/hid/hid-uclogic-core.c @@ -371,6 +371,8 @@ static const struct hid_device_id uclogic_devices[] = { USB_DEVICE_ID_HUION_TABLET) }, { HID_USB_DEVICE(USB_VENDOR_ID_HUION, USB_DEVICE_ID_HUION_HS64) }, + { HID_USB_DEVICE(USB_VENDOR_ID_TRUST, + USB_DEVICE_ID_TRUST_PANORA_TABLET) }, { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_HUION_TABLET) }, { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, diff --git a/drivers/hid/hid-uclogic-params.c b/drivers/hid/hid-uclogic-params.c index 56406cee401f..6af25c38b9cc 100644 --- a/drivers/hid/hid-uclogic-params.c +++ b/drivers/hid/hid-uclogic-params.c @@ -1045,6 +1045,8 @@ int uclogic_params_init(struct uclogic_params *params, uclogic_params_init_with_pen_unused(&p); } break; + case VID_PID(USB_VENDOR_ID_TRUST, + USB_DEVICE_ID_TRUST_PANORA_TABLET): case VID_PID(USB_VENDOR_ID_UGEE, USB_DEVICE_ID_UGEE_TABLET_G5): /* Ignore non-pen interfaces */ diff --git a/drivers/hid/i2c-hid/Kconfig b/drivers/hid/i2c-hid/Kconfig index c4e5dfeab2bd..a16c6a69680b 100644 --- a/drivers/hid/i2c-hid/Kconfig +++ b/drivers/hid/i2c-hid/Kconfig @@ -2,18 +2,55 @@ menu "I2C HID support" depends on I2C -config I2C_HID - tristate "HID over I2C transport layer" +config I2C_HID_ACPI + tristate "HID over I2C transport layer ACPI driver" default n - depends on I2C && INPUT - select HID + depends on I2C && INPUT && ACPI + help + Say Y here if you use a keyboard, a touchpad, a touchscreen, or any + other HID based devices which is connected to your computer via I2C. + This driver supports ACPI-based systems. + + If unsure, say N. + + This support is also available as a module. If so, the module + will be called i2c-hid-acpi. It will also build/depend on the + module i2c-hid. + +config I2C_HID_OF + tristate "HID over I2C transport layer Open Firmware driver" + default n + depends on I2C && INPUT && OF help Say Y here if you use a keyboard, a touchpad, a touchscreen, or any other HID based devices which is connected to your computer via I2C. + This driver supports Open Firmware (Device Tree)-based systems. If unsure, say N. This support is also available as a module. If so, the module - will be called i2c-hid. + will be called i2c-hid-of. It will also build/depend on the + module i2c-hid. + +config I2C_HID_OF_GOODIX + tristate "Driver for Goodix hid-i2c based devices on OF systems" + default n + depends on I2C && INPUT && OF + help + Say Y here if you want support for Goodix i2c devices that use + the i2c-hid protocol on Open Firmware (Device Tree)-based + systems. + + If unsure, say N. + + This support is also available as a module. If so, the module + will be called i2c-hid-of-goodix. It will also build/depend on + the module i2c-hid. endmenu + +config I2C_HID_CORE + tristate + default y if I2C_HID_ACPI=y || I2C_HID_OF=y || I2C_HID_OF_GOODIX=y + default m if I2C_HID_ACPI=m || I2C_HID_OF=m || I2C_HID_OF_GOODIX=m + select HID diff --git a/drivers/hid/i2c-hid/Makefile b/drivers/hid/i2c-hid/Makefile index 681b3896898e..302545a771f3 100644 --- a/drivers/hid/i2c-hid/Makefile +++ b/drivers/hid/i2c-hid/Makefile @@ -3,7 +3,11 @@ # Makefile for the I2C input drivers # -obj-$(CONFIG_I2C_HID) += i2c-hid.o +obj-$(CONFIG_I2C_HID_CORE) += i2c-hid.o i2c-hid-objs = i2c-hid-core.o i2c-hid-$(CONFIG_DMI) += i2c-hid-dmi-quirks.o + +obj-$(CONFIG_I2C_HID_ACPI) += i2c-hid-acpi.o +obj-$(CONFIG_I2C_HID_OF) += i2c-hid-of.o +obj-$(CONFIG_I2C_HID_OF_GOODIX) += i2c-hid-of-goodix.o diff --git a/drivers/hid/i2c-hid/i2c-hid-acpi.c b/drivers/hid/i2c-hid/i2c-hid-acpi.c new file mode 100644 index 000000000000..bb8c00e6be78 --- /dev/null +++ b/drivers/hid/i2c-hid/i2c-hid-acpi.c @@ -0,0 +1,143 @@ +/* + * HID over I2C ACPI Subclass + * + * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com> + * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France + * Copyright (c) 2012 Red Hat, Inc + * + * This code was forked out of the core code, which was partly based on + * "USB HID support for Linux": + * + * Copyright (c) 1999 Andreas Gal + * Copyright (c) 2000-2005 Vojtech Pavlik <vojtech@suse.cz> + * Copyright (c) 2005 Michael Haboustak <mike-@cinci.rr.com> for Concept2, Inc + * Copyright (c) 2007-2008 Oliver Neukum + * Copyright (c) 2006-2010 Jiri Kosina + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + */ + +#include <linux/acpi.h> +#include <linux/device.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pm.h> + +#include "i2c-hid.h" + +struct i2c_hid_acpi { + struct i2chid_ops ops; + struct i2c_client *client; +}; + +static const struct acpi_device_id i2c_hid_acpi_blacklist[] = { + /* + * The CHPN0001 ACPI device, which is used to describe the Chipone + * ICN8505 controller, has a _CID of PNP0C50 but is not HID compatible. + */ + {"CHPN0001", 0 }, + { }, +}; + +static int i2c_hid_acpi_get_descriptor(struct i2c_client *client) +{ + static guid_t i2c_hid_guid = + GUID_INIT(0x3CDFF6F7, 0x4267, 0x4555, + 0xAD, 0x05, 0xB3, 0x0A, 0x3D, 0x89, 0x38, 0xDE); + union acpi_object *obj; + struct acpi_device *adev; + acpi_handle handle; + u16 hid_descriptor_address; + + handle = ACPI_HANDLE(&client->dev); + if (!handle || acpi_bus_get_device(handle, &adev)) { + dev_err(&client->dev, "Error could not get ACPI device\n"); + return -ENODEV; + } + + if (acpi_match_device_ids(adev, i2c_hid_acpi_blacklist) == 0) + return -ENODEV; + + obj = acpi_evaluate_dsm_typed(handle, &i2c_hid_guid, 1, 1, NULL, + ACPI_TYPE_INTEGER); + if (!obj) { + dev_err(&client->dev, "Error _DSM call to get HID descriptor address failed\n"); + return -ENODEV; + } + + hid_descriptor_address = obj->integer.value; + ACPI_FREE(obj); + + return hid_descriptor_address; +} + +static void i2c_hid_acpi_shutdown_tail(struct i2chid_ops *ops) +{ + struct i2c_hid_acpi *ihid_acpi = + container_of(ops, struct i2c_hid_acpi, ops); + struct device *dev = &ihid_acpi->client->dev; + acpi_device_set_power(ACPI_COMPANION(dev), ACPI_STATE_D3_COLD); +} + +static int i2c_hid_acpi_probe(struct i2c_client *client, + const struct i2c_device_id *dev_id) +{ + struct device *dev = &client->dev; + struct i2c_hid_acpi *ihid_acpi; + struct acpi_device *adev; + u16 hid_descriptor_address; + int ret; + + ihid_acpi = devm_kzalloc(&client->dev, sizeof(*ihid_acpi), GFP_KERNEL); + if (!ihid_acpi) + return -ENOMEM; + + ihid_acpi->client = client; + ihid_acpi->ops.shutdown_tail = i2c_hid_acpi_shutdown_tail; + + ret = i2c_hid_acpi_get_descriptor(client); + if (ret < 0) + return ret; + hid_descriptor_address = ret; + + adev = ACPI_COMPANION(dev); + if (adev) + acpi_device_fix_up_power(adev); + + if (acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0) { + device_set_wakeup_capable(dev, true); + device_set_wakeup_enable(dev, false); + } + + return i2c_hid_core_probe(client, &ihid_acpi->ops, + hid_descriptor_address); +} + +static const struct acpi_device_id i2c_hid_acpi_match[] = { + {"ACPI0C50", 0 }, + {"PNP0C50", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(acpi, i2c_hid_acpi_match); + +static struct i2c_driver i2c_hid_acpi_driver = { + .driver = { + .name = "i2c_hid_acpi", + .pm = &i2c_hid_core_pm, + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + .acpi_match_table = ACPI_PTR(i2c_hid_acpi_match), + }, + + .probe = i2c_hid_acpi_probe, + .remove = i2c_hid_core_remove, + .shutdown = i2c_hid_core_shutdown, +}; + +module_i2c_driver(i2c_hid_acpi_driver); + +MODULE_DESCRIPTION("HID over I2C ACPI driver"); +MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/hid/i2c-hid/i2c-hid-core.c b/drivers/hid/i2c-hid/i2c-hid-core.c index bfe716d7ea44..9993133989a5 100644 --- a/drivers/hid/i2c-hid/i2c-hid-core.c +++ b/drivers/hid/i2c-hid/i2c-hid-core.c @@ -35,11 +35,6 @@ #include <linux/kernel.h> #include <linux/hid.h> #include <linux/mutex.h> -#include <linux/acpi.h> -#include <linux/of.h> -#include <linux/regulator/consumer.h> - -#include <linux/platform_data/i2c-hid.h> #include "../hid-ids.h" #include "i2c-hid.h" @@ -156,10 +151,10 @@ struct i2c_hid { wait_queue_head_t wait; /* For waiting the interrupt */ - struct i2c_hid_platform_data pdata; - bool irq_wake_enabled; struct mutex reset_lock; + + struct i2chid_ops *ops; }; static const struct i2c_hid_quirks { @@ -171,6 +166,8 @@ static const struct i2c_hid_quirks { I2C_HID_QUIRK_SET_PWR_WAKEUP_DEV }, { I2C_VENDOR_ID_HANTICK, I2C_PRODUCT_ID_HANTICK_5288, I2C_HID_QUIRK_NO_IRQ_AFTER_RESET }, + { I2C_VENDOR_ID_ITE, I2C_DEVICE_ID_ITE_VOYO_WINPAD_A15, + I2C_HID_QUIRK_NO_IRQ_AFTER_RESET }, { I2C_VENDOR_ID_RAYDIUM, I2C_PRODUCT_ID_RAYDIUM_3118, I2C_HID_QUIRK_NO_IRQ_AFTER_RESET }, { USB_VENDOR_ID_ELAN, HID_ANY_ID, @@ -884,144 +881,36 @@ static int i2c_hid_fetch_hid_descriptor(struct i2c_hid *ihid) return 0; } -#ifdef CONFIG_ACPI -static const struct acpi_device_id i2c_hid_acpi_blacklist[] = { - /* - * The CHPN0001 ACPI device, which is used to describe the Chipone - * ICN8505 controller, has a _CID of PNP0C50 but is not HID compatible. - */ - {"CHPN0001", 0 }, - { }, -}; - -static int i2c_hid_acpi_pdata(struct i2c_client *client, - struct i2c_hid_platform_data *pdata) -{ - static guid_t i2c_hid_guid = - GUID_INIT(0x3CDFF6F7, 0x4267, 0x4555, - 0xAD, 0x05, 0xB3, 0x0A, 0x3D, 0x89, 0x38, 0xDE); - union acpi_object *obj; - struct acpi_device *adev; - acpi_handle handle; - - handle = ACPI_HANDLE(&client->dev); - if (!handle || acpi_bus_get_device(handle, &adev)) { - dev_err(&client->dev, "Error could not get ACPI device\n"); - return -ENODEV; - } - - if (acpi_match_device_ids(adev, i2c_hid_acpi_blacklist) == 0) - return -ENODEV; - - obj = acpi_evaluate_dsm_typed(handle, &i2c_hid_guid, 1, 1, NULL, - ACPI_TYPE_INTEGER); - if (!obj) { - dev_err(&client->dev, "Error _DSM call to get HID descriptor address failed\n"); - return -ENODEV; - } - - pdata->hid_descriptor_address = obj->integer.value; - ACPI_FREE(obj); - - return 0; -} - -static void i2c_hid_acpi_fix_up_power(struct device *dev) -{ - struct acpi_device *adev; - - adev = ACPI_COMPANION(dev); - if (adev) - acpi_device_fix_up_power(adev); -} - -static void i2c_hid_acpi_enable_wakeup(struct device *dev) -{ - if (acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0) { - device_set_wakeup_capable(dev, true); - device_set_wakeup_enable(dev, false); - } -} - -static void i2c_hid_acpi_shutdown(struct device *dev) +static int i2c_hid_core_power_up(struct i2c_hid *ihid) { - acpi_device_set_power(ACPI_COMPANION(dev), ACPI_STATE_D3_COLD); -} + if (!ihid->ops->power_up) + return 0; -static const struct acpi_device_id i2c_hid_acpi_match[] = { - {"ACPI0C50", 0 }, - {"PNP0C50", 0 }, - { }, -}; -MODULE_DEVICE_TABLE(acpi, i2c_hid_acpi_match); -#else -static inline int i2c_hid_acpi_pdata(struct i2c_client *client, - struct i2c_hid_platform_data *pdata) -{ - return -ENODEV; + return ihid->ops->power_up(ihid->ops); } -static inline void i2c_hid_acpi_fix_up_power(struct device *dev) {} - -static inline void i2c_hid_acpi_enable_wakeup(struct device *dev) {} - -static inline void i2c_hid_acpi_shutdown(struct device *dev) {} -#endif - -#ifdef CONFIG_OF -static int i2c_hid_of_probe(struct i2c_client *client, - struct i2c_hid_platform_data *pdata) +static void i2c_hid_core_power_down(struct i2c_hid *ihid) { - struct device *dev = &client->dev; - u32 val; - int ret; - - ret = of_property_read_u32(dev->of_node, "hid-descr-addr", &val); - if (ret) { - dev_err(&client->dev, "HID register address not provided\n"); - return -ENODEV; - } - if (val >> 16) { - dev_err(&client->dev, "Bad HID register address: 0x%08x\n", - val); - return -EINVAL; - } - pdata->hid_descriptor_address = val; - - return 0; -} + if (!ihid->ops->power_down) + return; -static const struct of_device_id i2c_hid_of_match[] = { - { .compatible = "hid-over-i2c" }, - {}, -}; -MODULE_DEVICE_TABLE(of, i2c_hid_of_match); -#else -static inline int i2c_hid_of_probe(struct i2c_client *client, - struct i2c_hid_platform_data *pdata) -{ - return -ENODEV; + ihid->ops->power_down(ihid->ops); } -#endif -static void i2c_hid_fwnode_probe(struct i2c_client *client, - struct i2c_hid_platform_data *pdata) +static void i2c_hid_core_shutdown_tail(struct i2c_hid *ihid) { - u32 val; + if (!ihid->ops->shutdown_tail) + return; - if (!device_property_read_u32(&client->dev, "post-power-on-delay-ms", - &val)) - pdata->post_power_delay_ms = val; + ihid->ops->shutdown_tail(ihid->ops); } -static int i2c_hid_probe(struct i2c_client *client, - const struct i2c_device_id *dev_id) +int i2c_hid_core_probe(struct i2c_client *client, struct i2chid_ops *ops, + u16 hid_descriptor_address) { int ret; struct i2c_hid *ihid; struct hid_device *hid; - __u16 hidRegister; - struct i2c_hid_platform_data *platform_data = client->dev.platform_data; dbg_hid("HID probe called for i2c 0x%02x\n", client->addr); @@ -1042,44 +931,17 @@ static int i2c_hid_probe(struct i2c_client *client, if (!ihid) return -ENOMEM; - if (client->dev.of_node) { - ret = i2c_hid_of_probe(client, &ihid->pdata); - if (ret) - return ret; - } else if (!platform_data) { - ret = i2c_hid_acpi_pdata(client, &ihid->pdata); - if (ret) - return ret; - } else { - ihid->pdata = *platform_data; - } - - /* Parse platform agnostic common properties from ACPI / device tree */ - i2c_hid_fwnode_probe(client, &ihid->pdata); + ihid->ops = ops; - ihid->pdata.supplies[0].supply = "vdd"; - ihid->pdata.supplies[1].supply = "vddl"; - - ret = devm_regulator_bulk_get(&client->dev, - ARRAY_SIZE(ihid->pdata.supplies), - ihid->pdata.supplies); + ret = i2c_hid_core_power_up(ihid); if (ret) return ret; - ret = regulator_bulk_enable(ARRAY_SIZE(ihid->pdata.supplies), - ihid->pdata.supplies); - if (ret < 0) - return ret; - - if (ihid->pdata.post_power_delay_ms) - msleep(ihid->pdata.post_power_delay_ms); - i2c_set_clientdata(client, ihid); ihid->client = client; - hidRegister = ihid->pdata.hid_descriptor_address; - ihid->wHIDDescRegister = cpu_to_le16(hidRegister); + ihid->wHIDDescRegister = cpu_to_le16(hid_descriptor_address); init_waitqueue_head(&ihid->wait); mutex_init(&ihid->reset_lock); @@ -1089,11 +951,7 @@ static int i2c_hid_probe(struct i2c_client *client, * real computation later. */ ret = i2c_hid_alloc_buffers(ihid, HID_MIN_BUFFER_SIZE); if (ret < 0) - goto err_regulator; - - i2c_hid_acpi_fix_up_power(&client->dev); - - i2c_hid_acpi_enable_wakeup(&client->dev); + goto err_powered; device_enable_async_suspend(&client->dev); @@ -1102,19 +960,19 @@ static int i2c_hid_probe(struct i2c_client *client, if (ret < 0) { dev_dbg(&client->dev, "nothing at this address: %d\n", ret); ret = -ENXIO; - goto err_regulator; + goto err_powered; } ret = i2c_hid_fetch_hid_descriptor(ihid); if (ret < 0) { dev_err(&client->dev, "Failed to fetch the HID Descriptor\n"); - goto err_regulator; + goto err_powered; } ret = i2c_hid_init_irq(client); if (ret < 0) - goto err_regulator; + goto err_powered; hid = hid_allocate_device(); if (IS_ERR(hid)) { @@ -1153,14 +1011,14 @@ err_mem_free: err_irq: free_irq(client->irq, ihid); -err_regulator: - regulator_bulk_disable(ARRAY_SIZE(ihid->pdata.supplies), - ihid->pdata.supplies); +err_powered: + i2c_hid_core_power_down(ihid); i2c_hid_free_buffers(ihid); return ret; } +EXPORT_SYMBOL_GPL(i2c_hid_core_probe); -static int i2c_hid_remove(struct i2c_client *client) +int i2c_hid_core_remove(struct i2c_client *client) { struct i2c_hid *ihid = i2c_get_clientdata(client); struct hid_device *hid; @@ -1173,24 +1031,25 @@ static int i2c_hid_remove(struct i2c_client *client) if (ihid->bufsize) i2c_hid_free_buffers(ihid); - regulator_bulk_disable(ARRAY_SIZE(ihid->pdata.supplies), - ihid->pdata.supplies); + i2c_hid_core_power_down(ihid); return 0; } +EXPORT_SYMBOL_GPL(i2c_hid_core_remove); -static void i2c_hid_shutdown(struct i2c_client *client) +void i2c_hid_core_shutdown(struct i2c_client *client) { struct i2c_hid *ihid = i2c_get_clientdata(client); i2c_hid_set_power(client, I2C_HID_PWR_SLEEP); free_irq(client->irq, ihid); - i2c_hid_acpi_shutdown(&client->dev); + i2c_hid_core_shutdown_tail(ihid); } +EXPORT_SYMBOL_GPL(i2c_hid_core_shutdown); #ifdef CONFIG_PM_SLEEP -static int i2c_hid_suspend(struct device *dev) +static int i2c_hid_core_suspend(struct device *dev) { struct i2c_client *client = to_i2c_client(dev); struct i2c_hid *ihid = i2c_get_clientdata(client); @@ -1217,14 +1076,13 @@ static int i2c_hid_suspend(struct device *dev) hid_warn(hid, "Failed to enable irq wake: %d\n", wake_status); } else { - regulator_bulk_disable(ARRAY_SIZE(ihid->pdata.supplies), - ihid->pdata.supplies); + i2c_hid_core_power_down(ihid); } return 0; } -static int i2c_hid_resume(struct device *dev) +static int i2c_hid_core_resume(struct device *dev) { int ret; struct i2c_client *client = to_i2c_client(dev); @@ -1233,13 +1091,7 @@ static int i2c_hid_resume(struct device *dev) int wake_status; if (!device_may_wakeup(&client->dev)) { - ret = regulator_bulk_enable(ARRAY_SIZE(ihid->pdata.supplies), - ihid->pdata.supplies); - if (ret) - hid_warn(hid, "Failed to enable supplies: %d\n", ret); - - if (ihid->pdata.post_power_delay_ms) - msleep(ihid->pdata.post_power_delay_ms); + i2c_hid_core_power_up(ihid); } else if (ihid->irq_wake_enabled) { wake_status = disable_irq_wake(client->irq); if (!wake_status) @@ -1276,34 +1128,10 @@ static int i2c_hid_resume(struct device *dev) } #endif -static const struct dev_pm_ops i2c_hid_pm = { - SET_SYSTEM_SLEEP_PM_OPS(i2c_hid_suspend, i2c_hid_resume) +const struct dev_pm_ops i2c_hid_core_pm = { + SET_SYSTEM_SLEEP_PM_OPS(i2c_hid_core_suspend, i2c_hid_core_resume) }; - -static const struct i2c_device_id i2c_hid_id_table[] = { - { "hid", 0 }, - { "hid-over-i2c", 0 }, - { }, -}; -MODULE_DEVICE_TABLE(i2c, i2c_hid_id_table); - - -static struct i2c_driver i2c_hid_driver = { - .driver = { - .name = "i2c_hid", - .pm = &i2c_hid_pm, - .probe_type = PROBE_PREFER_ASYNCHRONOUS, - .acpi_match_table = ACPI_PTR(i2c_hid_acpi_match), - .of_match_table = of_match_ptr(i2c_hid_of_match), - }, - - .probe = i2c_hid_probe, - .remove = i2c_hid_remove, - .shutdown = i2c_hid_shutdown, - .id_table = i2c_hid_id_table, -}; - -module_i2c_driver(i2c_hid_driver); +EXPORT_SYMBOL_GPL(i2c_hid_core_pm); MODULE_DESCRIPTION("HID over I2C core driver"); MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>"); diff --git a/drivers/hid/i2c-hid/i2c-hid-of-goodix.c b/drivers/hid/i2c-hid/i2c-hid-of-goodix.c new file mode 100644 index 000000000000..ee0225982a82 --- /dev/null +++ b/drivers/hid/i2c-hid/i2c-hid-of-goodix.c @@ -0,0 +1,116 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Driver for Goodix touchscreens that use the i2c-hid protocol. + * + * Copyright 2020 Google LLC + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/pm.h> +#include <linux/regulator/consumer.h> + +#include "i2c-hid.h" + +struct goodix_i2c_hid_timing_data { + unsigned int post_gpio_reset_delay_ms; + unsigned int post_power_delay_ms; +}; + +struct i2c_hid_of_goodix { + struct i2chid_ops ops; + + struct regulator *vdd; + struct gpio_desc *reset_gpio; + const struct goodix_i2c_hid_timing_data *timings; +}; + +static int goodix_i2c_hid_power_up(struct i2chid_ops *ops) +{ + struct i2c_hid_of_goodix *ihid_goodix = + container_of(ops, struct i2c_hid_of_goodix, ops); + int ret; + + ret = regulator_enable(ihid_goodix->vdd); + if (ret) + return ret; + + if (ihid_goodix->timings->post_power_delay_ms) + msleep(ihid_goodix->timings->post_power_delay_ms); + + gpiod_set_value_cansleep(ihid_goodix->reset_gpio, 0); + if (ihid_goodix->timings->post_gpio_reset_delay_ms) + msleep(ihid_goodix->timings->post_gpio_reset_delay_ms); + + return 0; +} + +static void goodix_i2c_hid_power_down(struct i2chid_ops *ops) +{ + struct i2c_hid_of_goodix *ihid_goodix = + container_of(ops, struct i2c_hid_of_goodix, ops); + + gpiod_set_value_cansleep(ihid_goodix->reset_gpio, 1); + regulator_disable(ihid_goodix->vdd); +} + +static int i2c_hid_of_goodix_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_hid_of_goodix *ihid_goodix; + + ihid_goodix = devm_kzalloc(&client->dev, sizeof(*ihid_goodix), + GFP_KERNEL); + if (!ihid_goodix) + return -ENOMEM; + + ihid_goodix->ops.power_up = goodix_i2c_hid_power_up; + ihid_goodix->ops.power_down = goodix_i2c_hid_power_down; + + /* Start out with reset asserted */ + ihid_goodix->reset_gpio = + devm_gpiod_get_optional(&client->dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(ihid_goodix->reset_gpio)) + return PTR_ERR(ihid_goodix->reset_gpio); + + ihid_goodix->vdd = devm_regulator_get(&client->dev, "vdd"); + if (IS_ERR(ihid_goodix->vdd)) + return PTR_ERR(ihid_goodix->vdd); + + ihid_goodix->timings = device_get_match_data(&client->dev); + + return i2c_hid_core_probe(client, &ihid_goodix->ops, 0x0001); +} + +static const struct goodix_i2c_hid_timing_data goodix_gt7375p_timing_data = { + .post_power_delay_ms = 10, + .post_gpio_reset_delay_ms = 180, +}; + +static const struct of_device_id goodix_i2c_hid_of_match[] = { + { .compatible = "goodix,gt7375p", .data = &goodix_gt7375p_timing_data }, + { } +}; +MODULE_DEVICE_TABLE(of, goodix_i2c_hid_of_match); + +static struct i2c_driver goodix_i2c_hid_ts_driver = { + .driver = { + .name = "i2c_hid_of_goodix", + .pm = &i2c_hid_core_pm, + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + .of_match_table = of_match_ptr(goodix_i2c_hid_of_match), + }, + .probe = i2c_hid_of_goodix_probe, + .remove = i2c_hid_core_remove, + .shutdown = i2c_hid_core_shutdown, +}; +module_i2c_driver(goodix_i2c_hid_ts_driver); + +MODULE_AUTHOR("Douglas Anderson <dianders@chromium.org>"); +MODULE_DESCRIPTION("Goodix i2c-hid touchscreen driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/hid/i2c-hid/i2c-hid-of.c b/drivers/hid/i2c-hid/i2c-hid-of.c new file mode 100644 index 000000000000..4bf7cea92637 --- /dev/null +++ b/drivers/hid/i2c-hid/i2c-hid-of.c @@ -0,0 +1,143 @@ +/* + * HID over I2C Open Firmware Subclass + * + * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com> + * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France + * Copyright (c) 2012 Red Hat, Inc + * + * This code was forked out of the core code, which was partly based on + * "USB HID support for Linux": + * + * Copyright (c) 1999 Andreas Gal + * Copyright (c) 2000-2005 Vojtech Pavlik <vojtech@suse.cz> + * Copyright (c) 2005 Michael Haboustak <mike-@cinci.rr.com> for Concept2, Inc + * Copyright (c) 2007-2008 Oliver Neukum + * Copyright (c) 2006-2010 Jiri Kosina + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/pm.h> +#include <linux/regulator/consumer.h> + +#include "i2c-hid.h" + +struct i2c_hid_of { + struct i2chid_ops ops; + + struct i2c_client *client; + struct regulator_bulk_data supplies[2]; + int post_power_delay_ms; +}; + +static int i2c_hid_of_power_up(struct i2chid_ops *ops) +{ + struct i2c_hid_of *ihid_of = container_of(ops, struct i2c_hid_of, ops); + struct device *dev = &ihid_of->client->dev; + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(ihid_of->supplies), + ihid_of->supplies); + if (ret) { + dev_warn(dev, "Failed to enable supplies: %d\n", ret); + return ret; + } + + if (ihid_of->post_power_delay_ms) + msleep(ihid_of->post_power_delay_ms); + + return 0; +} + +static void i2c_hid_of_power_down(struct i2chid_ops *ops) +{ + struct i2c_hid_of *ihid_of = container_of(ops, struct i2c_hid_of, ops); + + regulator_bulk_disable(ARRAY_SIZE(ihid_of->supplies), + ihid_of->supplies); +} + +static int i2c_hid_of_probe(struct i2c_client *client, + const struct i2c_device_id *dev_id) +{ + struct device *dev = &client->dev; + struct i2c_hid_of *ihid_of; + u16 hid_descriptor_address; + int ret; + u32 val; + + ihid_of = devm_kzalloc(&client->dev, sizeof(*ihid_of), GFP_KERNEL); + if (!ihid_of) + return -ENOMEM; + + ihid_of->ops.power_up = i2c_hid_of_power_up; + ihid_of->ops.power_down = i2c_hid_of_power_down; + + ret = of_property_read_u32(dev->of_node, "hid-descr-addr", &val); + if (ret) { + dev_err(&client->dev, "HID register address not provided\n"); + return -ENODEV; + } + if (val >> 16) { + dev_err(&client->dev, "Bad HID register address: 0x%08x\n", + val); + return -EINVAL; + } + hid_descriptor_address = val; + + if (!device_property_read_u32(&client->dev, "post-power-on-delay-ms", + &val)) + ihid_of->post_power_delay_ms = val; + + ihid_of->supplies[0].supply = "vdd"; + ihid_of->supplies[1].supply = "vddl"; + ret = devm_regulator_bulk_get(&client->dev, + ARRAY_SIZE(ihid_of->supplies), + ihid_of->supplies); + if (ret) + return ret; + + return i2c_hid_core_probe(client, &ihid_of->ops, + hid_descriptor_address); +} + +static const struct of_device_id i2c_hid_of_match[] = { + { .compatible = "hid-over-i2c" }, + {}, +}; +MODULE_DEVICE_TABLE(of, i2c_hid_of_match); + +static const struct i2c_device_id i2c_hid_of_id_table[] = { + { "hid", 0 }, + { "hid-over-i2c", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(i2c, i2c_hid_of_id_table); + +static struct i2c_driver i2c_hid_of_driver = { + .driver = { + .name = "i2c_hid_of", + .pm = &i2c_hid_core_pm, + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + .of_match_table = of_match_ptr(i2c_hid_of_match), + }, + + .probe = i2c_hid_of_probe, + .remove = i2c_hid_core_remove, + .shutdown = i2c_hid_core_shutdown, + .id_table = i2c_hid_of_id_table, +}; + +module_i2c_driver(i2c_hid_of_driver); + +MODULE_DESCRIPTION("HID over I2C OF driver"); +MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/hid/i2c-hid/i2c-hid.h b/drivers/hid/i2c-hid/i2c-hid.h index a8c19aef5824..05a7827d211a 100644 --- a/drivers/hid/i2c-hid/i2c-hid.h +++ b/drivers/hid/i2c-hid/i2c-hid.h @@ -3,6 +3,7 @@ #ifndef I2C_HID_H #define I2C_HID_H +#include <linux/i2c.h> #ifdef CONFIG_DMI struct i2c_hid_desc *i2c_hid_get_dmi_i2c_hid_desc_override(uint8_t *i2c_name); @@ -17,4 +18,25 @@ static inline char *i2c_hid_get_dmi_hid_report_desc_override(uint8_t *i2c_name, { return NULL; } #endif +/** + * struct i2chid_ops - Ops provided to the core. + * + * @power_up: do sequencing to power up the device. + * @power_down: do sequencing to power down the device. + * @shutdown_tail: called at the end of shutdown. + */ +struct i2chid_ops { + int (*power_up)(struct i2chid_ops *ops); + void (*power_down)(struct i2chid_ops *ops); + void (*shutdown_tail)(struct i2chid_ops *ops); +}; + +int i2c_hid_core_probe(struct i2c_client *client, struct i2chid_ops *ops, + u16 hid_descriptor_address); +int i2c_hid_core_remove(struct i2c_client *client); + +void i2c_hid_core_shutdown(struct i2c_client *client); + +extern const struct dev_pm_ops i2c_hid_core_pm; + #endif diff --git a/drivers/hid/intel-ish-hid/ipc/hw-ish.h b/drivers/hid/intel-ish-hid/ipc/hw-ish.h index 1fb294ca463e..21b87e4003af 100644 --- a/drivers/hid/intel-ish-hid/ipc/hw-ish.h +++ b/drivers/hid/intel-ish-hid/ipc/hw-ish.h @@ -27,6 +27,7 @@ #define CMP_H_DEVICE_ID 0x06FC #define EHL_Ax_DEVICE_ID 0x4BB3 #define TGL_LP_DEVICE_ID 0xA0FC +#define TGL_H_DEVICE_ID 0x43FC #define REVISION_ID_CHT_A0 0x6 #define REVISION_ID_CHT_Ax_SI 0x0 @@ -81,5 +82,6 @@ struct ishtp_device *ish_dev_init(struct pci_dev *pdev); int ish_hw_start(struct ishtp_device *dev); void ish_device_disable(struct ishtp_device *dev); int ish_disable_dma(struct ishtp_device *dev); +void ish_set_host_ready(struct ishtp_device *dev); #endif /* _ISHTP_HW_ISH_H_ */ diff --git a/drivers/hid/intel-ish-hid/ipc/ipc.c b/drivers/hid/intel-ish-hid/ipc/ipc.c index a45ac7fa417b..47bbeb8b492b 100644 --- a/drivers/hid/intel-ish-hid/ipc/ipc.c +++ b/drivers/hid/intel-ish-hid/ipc/ipc.c @@ -193,6 +193,33 @@ static void ish_clr_host_rdy(struct ishtp_device *dev) ish_reg_write(dev, IPC_REG_HOST_COMM, host_status); } +static bool ish_chk_host_rdy(struct ishtp_device *dev) +{ + uint32_t host_status = ish_reg_read(dev, IPC_REG_HOST_COMM); + + return (host_status & IPC_HOSTCOMM_READY_BIT); +} + +/** + * ish_set_host_ready() - reconfig ipc host registers + * @dev: ishtp device pointer + * + * Set host to ready state + * This API is called in some case: + * fw is still on, but ipc is powered down. + * such as OOB case. + * + * Return: 0 for success else error fault code + */ +void ish_set_host_ready(struct ishtp_device *dev) +{ + if (ish_chk_host_rdy(dev)) + return; + + ish_set_host_rdy(dev); + set_host_ready(dev); +} + /** * _ishtp_read_hdr() - Read message header * @dev: ISHTP device pointer diff --git a/drivers/hid/intel-ish-hid/ipc/pci-ish.c b/drivers/hid/intel-ish-hid/ipc/pci-ish.c index c6d48a8648b7..06081cf9b85a 100644 --- a/drivers/hid/intel-ish-hid/ipc/pci-ish.c +++ b/drivers/hid/intel-ish-hid/ipc/pci-ish.c @@ -5,6 +5,7 @@ * Copyright (c) 2014-2016, Intel Corporation. */ +#include <linux/acpi.h> #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/kernel.h> @@ -37,6 +38,7 @@ static const struct pci_device_id ish_pci_tbl[] = { {PCI_DEVICE(PCI_VENDOR_ID_INTEL, CMP_H_DEVICE_ID)}, {PCI_DEVICE(PCI_VENDOR_ID_INTEL, EHL_Ax_DEVICE_ID)}, {PCI_DEVICE(PCI_VENDOR_ID_INTEL, TGL_LP_DEVICE_ID)}, + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, TGL_H_DEVICE_ID)}, {0, } }; MODULE_DEVICE_TABLE(pci, ish_pci_tbl); @@ -111,6 +113,42 @@ static inline bool ish_should_leave_d0i3(struct pci_dev *pdev) return !pm_resume_via_firmware() || pdev->device == CHV_DEVICE_ID; } +static int enable_gpe(struct device *dev) +{ +#ifdef CONFIG_ACPI + acpi_status acpi_sts; + struct acpi_device *adev; + struct acpi_device_wakeup *wakeup; + + adev = ACPI_COMPANION(dev); + if (!adev) { + dev_err(dev, "get acpi handle failed\n"); + return -ENODEV; + } + wakeup = &adev->wakeup; + + acpi_sts = acpi_enable_gpe(wakeup->gpe_device, wakeup->gpe_number); + if (ACPI_FAILURE(acpi_sts)) { + dev_err(dev, "enable ose_gpe failed\n"); + return -EIO; + } + + return 0; +#else + return -ENODEV; +#endif +} + +static void enable_pme_wake(struct pci_dev *pdev) +{ + if ((pci_pme_capable(pdev, PCI_D0) || + pci_pme_capable(pdev, PCI_D3hot) || + pci_pme_capable(pdev, PCI_D3cold)) && !enable_gpe(&pdev->dev)) { + pci_pme_active(pdev, true); + dev_dbg(&pdev->dev, "ish ipc driver pme wake enabled\n"); + } +} + /** * ish_probe() - PCI driver probe callback * @pdev: pci device @@ -179,6 +217,10 @@ static int ish_probe(struct pci_dev *pdev, const struct pci_device_id *ent) init_waitqueue_head(&ishtp->suspend_wait); init_waitqueue_head(&ishtp->resume_wait); + /* Enable PME for EHL */ + if (pdev->device == EHL_Ax_DEVICE_ID) + enable_pme_wake(pdev); + ret = ish_init(ishtp); if (ret) return ret; @@ -218,11 +260,15 @@ static void __maybe_unused ish_resume_handler(struct work_struct *work) { struct pci_dev *pdev = to_pci_dev(ish_resume_device); struct ishtp_device *dev = pci_get_drvdata(pdev); + uint32_t fwsts = dev->ops->get_fw_status(dev); int ret; - if (ish_should_leave_d0i3(pdev) && !dev->suspend_flag) { + if (ish_should_leave_d0i3(pdev) && !dev->suspend_flag + && IPC_IS_ISH_ILUP(fwsts)) { disable_irq_wake(pdev->irq); + ish_set_host_ready(dev); + ishtp_send_resume(dev); /* Waiting to get resume response */ @@ -317,6 +363,13 @@ static int __maybe_unused ish_resume(struct device *device) struct pci_dev *pdev = to_pci_dev(device); struct ishtp_device *dev = pci_get_drvdata(pdev); + /* add this to finish power flow for EHL */ + if (dev->pdev->device == EHL_Ax_DEVICE_ID) { + pci_set_power_state(pdev, PCI_D0); + enable_pme_wake(pdev); + dev_dbg(dev->devc, "set power state to D0 for ehl\n"); + } + ish_resume_device = device; dev->resume_flag = 1; diff --git a/drivers/hid/wacom_sys.c b/drivers/hid/wacom_sys.c index aa9e48876ced..8328ef155c46 100644 --- a/drivers/hid/wacom_sys.c +++ b/drivers/hid/wacom_sys.c @@ -1825,7 +1825,7 @@ static ssize_t wacom_show_speed(struct device *dev, struct hid_device *hdev = to_hid_device(dev); struct wacom *wacom = hid_get_drvdata(hdev); - return snprintf(buf, PAGE_SIZE, "%i\n", wacom->wacom_wac.bt_high_speed); + return sysfs_emit(buf, "%i\n", wacom->wacom_wac.bt_high_speed); } static ssize_t wacom_store_speed(struct device *dev, diff --git a/drivers/hid/wacom_wac.c b/drivers/hid/wacom_wac.c index 1bd0eb71559c..44d715c12f6a 100644 --- a/drivers/hid/wacom_wac.c +++ b/drivers/hid/wacom_wac.c @@ -2600,7 +2600,12 @@ static void wacom_wac_finger_event(struct hid_device *hdev, wacom_wac->is_invalid_bt_frame = !value; return; case HID_DG_CONTACTMAX: - features->touch_max = value; + if (!features->touch_max) { + features->touch_max = value; + } else { + hid_warn(hdev, "%s: ignoring attempt to overwrite non-zero touch_max " + "%d -> %d\n", __func__, features->touch_max, value); + } return; } diff --git a/include/linux/hid-sensor-hub.h b/include/linux/hid-sensor-hub.h index 46bcef380446..763802b2b8f9 100644 --- a/include/linux/hid-sensor-hub.h +++ b/include/linux/hid-sensor-hub.h @@ -150,7 +150,7 @@ int sensor_hub_remove_callback(struct hid_sensor_hub_device *hsdev, * @info: return information about attribute after parsing report * * Parses report and returns the attribute information such as report id, -* field index, units and exponet etc. +* field index, units and exponent etc. */ int sensor_hub_input_get_attribute_info(struct hid_sensor_hub_device *hsdev, u8 type, @@ -167,7 +167,7 @@ int sensor_hub_input_get_attribute_info(struct hid_sensor_hub_device *hsdev, * @is_signed: If true then fields < 32 bits will be sign-extended * * Issues a synchronous or asynchronous read request for an input attribute. -* Returns data upto 32 bits. +* Return: data up to 32 bits. */ enum sensor_hub_read_flags { @@ -205,8 +205,9 @@ int sensor_hub_set_feature(struct hid_sensor_hub_device *hsdev, u32 report_id, * @buffer: buffer to copy output * * Used to get a field in feature report. For example this can get polling -* interval, sensitivity, activate/deactivate state. On success it returns -* number of bytes copied to buffer. On failure, it returns value < 0. +* interval, sensitivity, activate/deactivate state. +* Return: On success, it returns the number of bytes copied to buffer. +* On failure, it returns value < 0. */ int sensor_hub_get_feature(struct hid_sensor_hub_device *hsdev, u32 report_id, u32 field_index, int buffer_size, void *buffer); diff --git a/include/linux/hid.h b/include/linux/hid.h index c39d71eb1fd0..ef702b3f56e3 100644 --- a/include/linux/hid.h +++ b/include/linux/hid.h @@ -918,7 +918,7 @@ __u32 hid_field_extract(const struct hid_device *hid, __u8 *report, /** * hid_device_io_start - enable HID input during probe, remove * - * @hid - the device + * @hid: the device * * This should only be called during probe or remove and only be * called by the thread calling probe or remove. It will allow @@ -936,7 +936,7 @@ static inline void hid_device_io_start(struct hid_device *hid) { /** * hid_device_io_stop - disable HID input during probe, remove * - * @hid - the device + * @hid: the device * * Should only be called after hid_device_io_start. It will prevent * incoming packets from going to the driver for the duration of @@ -1010,6 +1010,13 @@ static inline void hid_map_usage(struct hid_input *hidinput, /** * hid_map_usage_clear - map usage input bits and clear the input bit * + * @hidinput: hidinput which we are interested in + * @usage: usage to fill in + * @bit: pointer to input->{}bit (out parameter) + * @max: maximal valid usage->code to consider later (out parameter) + * @type: input event type (EV_KEY, EV_REL, ...) + * @c: code which corresponds to this usage and type + * * The same as hid_map_usage, except the @c bit is also cleared in supported * bits (@bit). */ @@ -1084,7 +1091,7 @@ static inline void hid_hw_request(struct hid_device *hdev, * @rtype: HID report type * @reqtype: HID_REQ_GET_REPORT or HID_REQ_SET_REPORT * - * @return: count of data transfered, negative if error + * Return: count of data transferred, negative if error * * Same behavior as hid_hw_request, but with raw buffers instead. */ @@ -1106,7 +1113,7 @@ static inline int hid_hw_raw_request(struct hid_device *hdev, * @buf: raw data to transfer * @len: length of buf * - * @return: count of data transfered, negative if error + * Return: count of data transferred, negative if error */ static inline int hid_hw_output_report(struct hid_device *hdev, __u8 *buf, size_t len) diff --git a/include/linux/platform_data/i2c-hid.h b/include/linux/platform_data/i2c-hid.h deleted file mode 100644 index c628bb5e1061..000000000000 --- a/include/linux/platform_data/i2c-hid.h +++ /dev/null @@ -1,41 +0,0 @@ -/* - * HID over I2C protocol implementation - * - * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com> - * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file COPYING in the main directory of this archive for - * more details. - */ - -#ifndef __LINUX_I2C_HID_H -#define __LINUX_I2C_HID_H - -#include <linux/regulator/consumer.h> -#include <linux/types.h> - -/** - * struct i2chid_platform_data - used by hid over i2c implementation. - * @hid_descriptor_address: i2c register where the HID descriptor is stored. - * @supplies: regulators for powering on the device. - * @post_power_delay_ms: delay after powering on before device is usable. - * - * Note that it is the responsibility of the platform driver (or the acpi 5.0 - * driver, or the flattened device tree) to setup the irq related to the gpio in - * the struct i2c_board_info. - * The platform driver should also setup the gpio according to the device: - * - * A typical example is the following: - * irq = gpio_to_irq(intr_gpio); - * hkdk4412_i2c_devs5[0].irq = irq; // store the irq in i2c_board_info - * gpio_request(intr_gpio, "elan-irq"); - * s3c_gpio_setpull(intr_gpio, S3C_GPIO_PULL_UP); - */ -struct i2c_hid_platform_data { - u16 hid_descriptor_address; - struct regulator_bulk_data supplies[2]; - int post_power_delay_ms; -}; - -#endif /* __LINUX_I2C_HID_H */ |