Merge branch 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
  amba pl011: platform data for reg lockup and glitch v2
  amba pl011: workaround for uart registers lockup
  tty: n_gsm: improper skb_pull() use was leaking framed data
  tty: n_gsm: Fixed logic to decode break signal from modem status
  TTY: ntty, add one more sanity check
  TTY: ldisc, do not close until there are readers
  8250: Fix capabilities when changing the port type
  8250_pci: Fix missing const from merges
  ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
  serial: ioremap warning fix for jsm driver.
  8250_pci: add -ENODEV code for Intel EG20T PCH

6 files changed, 199 insertions, 8 deletions

diff --git a/drivers/tty/serial/8250.c b/drivers/tty/serial/8250.c
index b40f7b90c81d..b4129f53fb1b 100644
--- a/drivers/tty/serial/8250.c
+++ b/drivers/tty/serial/8250.c
@@ -3318,6 +3318,7 @@ void serial8250_unregister_port(int line)
 		uart->port.flags &= ~UPF_BOOT_AUTOCONF;
 		uart->port.type = PORT_UNKNOWN;
 		uart->port.dev = &serial8250_isa_devs->dev;
+		uart->capabilities = uart_config[uart->port.type].flags;
 		uart_add_one_port(&serial8250_reg, &uart->port);
 	} else {
 		uart->port.dev = NULL;
diff --git a/drivers/tty/serial/8250_pci.c b/drivers/tty/serial/8250_pci.c
index 78e98a5cef96..f41b4259ecdd 100644
--- a/drivers/tty/serial/8250_pci.c
+++ b/drivers/tty/serial/8250_pci.c
@@ -994,6 +994,15 @@ static int skip_tx_en_setup(struct serial_private *priv,
 	return pci_default_setup(priv, board, port, idx);
 }
 
+static int pci_eg20t_init(struct pci_dev *dev)
+{
+#if defined(CONFIG_SERIAL_PCH_UART) || defined(CONFIG_SERIAL_PCH_UART_MODULE)
+	return -ENODEV;
+#else
+	return 0;
+#endif
+}
+
 /* This should be in linux/pci_ids.h */
 #define PCI_VENDOR_ID_SBSMODULARIO	0x124B
 #define PCI_SUBVENDOR_ID_SBSMODULARIO	0x124B
@@ -1446,6 +1455,56 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.init			= pci_oxsemi_tornado_init,
 		.setup		= pci_default_setup,
 	},
+	{
+		.vendor         = PCI_VENDOR_ID_INTEL,
+		.device         = 0x8811,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = PCI_VENDOR_ID_INTEL,
+		.device         = 0x8812,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = PCI_VENDOR_ID_INTEL,
+		.device         = 0x8813,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = PCI_VENDOR_ID_INTEL,
+		.device         = 0x8814,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = 0x10DB,
+		.device         = 0x8027,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = 0x10DB,
+		.device         = 0x8028,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = 0x10DB,
+		.device         = 0x8029,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = 0x10DB,
+		.device         = 0x800C,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = 0x10DB,
+		.device         = 0x800D,
+		.init		= pci_eg20t_init,
+	},
+	{
+		.vendor         = 0x10DB,
+		.device         = 0x800D,
+		.init		= pci_eg20t_init,
+	},
 	/*
 	 * Cronyx Omega PCI (PLX-chip based)
 	 */
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 8dc0541feecc..f5f6831b0a64 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -50,6 +50,7 @@
 #include <linux/dmaengine.h>
 #include <linux/dma-mapping.h>
 #include <linux/scatterlist.h>
+#include <linux/delay.h>
 
 #include <asm/io.h>
 #include <asm/sizes.h>
@@ -65,6 +66,30 @@
 #define UART_DR_ERROR		(UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE)
 #define UART_DUMMY_DR_RX	(1 << 16)
 
+
+#define UART_WA_SAVE_NR 14
+
+static void pl011_lockup_wa(unsigned long data);
+static const u32 uart_wa_reg[UART_WA_SAVE_NR] = {
+	ST_UART011_DMAWM,
+	ST_UART011_TIMEOUT,
+	ST_UART011_LCRH_RX,
+	UART011_IBRD,
+	UART011_FBRD,
+	ST_UART011_LCRH_TX,
+	UART011_IFLS,
+	ST_UART011_XFCR,
+	ST_UART011_XON1,
+	ST_UART011_XON2,
+	ST_UART011_XOFF1,
+	ST_UART011_XOFF2,
+	UART011_CR,
+	UART011_IMSC
+};
+
+static u32 uart_wa_regdata[UART_WA_SAVE_NR];
+static DECLARE_TASKLET(pl011_lockup_tlet, pl011_lockup_wa, 0);
+
 /* There is by now at least one vendor with differing details, so handle it */
 struct vendor_data {
 	unsigned int		ifls;
@@ -72,6 +97,7 @@ struct vendor_data {
 	unsigned int		lcrh_tx;
 	unsigned int		lcrh_rx;
 	bool			oversampling;
+	bool			interrupt_may_hang;   /* vendor-specific */
 	bool			dma_threshold;
 };
 
@@ -90,9 +116,12 @@ static struct vendor_data vendor_st = {
 	.lcrh_tx		= ST_UART011_LCRH_TX,
 	.lcrh_rx		= ST_UART011_LCRH_RX,
 	.oversampling		= true,
+	.interrupt_may_hang	= true,
 	.dma_threshold		= true,
 };
 
+static struct uart_amba_port *amba_ports[UART_NR];
+
 /* Deals with DMA transactions */
 
 struct pl011_sgbuf {
@@ -132,6 +161,7 @@ struct uart_amba_port {
 	unsigned int		lcrh_rx;	/* vendor-specific */
 	bool			autorts;
 	char			type[12];
+	bool			interrupt_may_hang; /* vendor-specific */
 #ifdef CONFIG_DMA_ENGINE
 	/* DMA stuff */
 	bool			using_tx_dma;
@@ -1008,6 +1038,68 @@ static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
 #endif
 
 
+/*
+ * pl011_lockup_wa
+ * This workaround aims to break the deadlock situation
+ * when after long transfer over uart in hardware flow
+ * control, uart interrupt registers cannot be cleared.
+ * Hence uart transfer gets blocked.
+ *
+ * It is seen that during such deadlock condition ICR
+ * don't get cleared even on multiple write. This leads
+ * pass_counter to decrease and finally reach zero. This
+ * can be taken as trigger point to run this UART_BT_WA.
+ *
+ */
+static void pl011_lockup_wa(unsigned long data)
+{
+	struct uart_amba_port *uap = amba_ports[0];
+	void __iomem *base = uap->port.membase;
+	struct circ_buf *xmit = &uap->port.state->xmit;
+	struct tty_struct *tty = uap->port.state->port.tty;
+	int buf_empty_retries = 200;
+	int loop;
+
+	/* Stop HCI layer from submitting data for tx */
+	tty->hw_stopped = 1;
+	while (!uart_circ_empty(xmit)) {
+		if (buf_empty_retries-- == 0)
+			break;
+		udelay(100);
+	}
+
+	/* Backup registers */
+	for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
+		uart_wa_regdata[loop] = readl(base + uart_wa_reg[loop]);
+
+	/* Disable UART so that FIFO data is flushed out */
+	writew(0x00, uap->port.membase + UART011_CR);
+
+	/* Soft reset UART module */
+	if (uap->port.dev->platform_data) {
+		struct amba_pl011_data *plat;
+
+		plat = uap->port.dev->platform_data;
+		if (plat->reset)
+			plat->reset();
+	}
+
+	/* Restore registers */
+	for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
+		writew(uart_wa_regdata[loop] ,
+				uap->port.membase + uart_wa_reg[loop]);
+
+	/* Initialise the old status of the modem signals */
+	uap->old_status = readw(uap->port.membase + UART01x_FR) &
+		UART01x_FR_MODEM_ANY;
+
+	if (readl(base + UART011_MIS) & 0x2)
+		printk(KERN_EMERG "UART_BT_WA: ***FAILED***\n");
+
+	/* Start Tx/Rx */
+	tty->hw_stopped = 0;
+}
+
 static void pl011_stop_tx(struct uart_port *port)
 {
 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
@@ -1158,8 +1250,11 @@ static irqreturn_t pl011_int(int irq, void *dev_id)
 			if (status & UART011_TXIS)
 				pl011_tx_chars(uap);
 
-			if (pass_counter-- == 0)
+			if (pass_counter-- == 0) {
+				if (uap->interrupt_may_hang)
+					tasklet_schedule(&pl011_lockup_tlet);
 				break;
+			}
 
 			status = readw(uap->port.membase + UART011_MIS);
 		} while (status != 0);
@@ -1339,6 +1434,14 @@ static int pl011_startup(struct uart_port *port)
 	writew(uap->im, uap->port.membase + UART011_IMSC);
 	spin_unlock_irq(&uap->port.lock);
 
+	if (uap->port.dev->platform_data) {
+		struct amba_pl011_data *plat;
+
+		plat = uap->port.dev->platform_data;
+		if (plat->init)
+			plat->init();
+	}
+
 	return 0;
 
  clk_dis:
@@ -1394,6 +1497,15 @@ static void pl011_shutdown(struct uart_port *port)
 	 * Shut down the clock producer
 	 */
 	clk_disable(uap->clk);
+
+	if (uap->port.dev->platform_data) {
+		struct amba_pl011_data *plat;
+
+		plat = uap->port.dev->platform_data;
+		if (plat->exit)
+			plat->exit();
+	}
+
 }
 
 static void
@@ -1700,6 +1812,14 @@ static int __init pl011_console_setup(struct console *co, char *options)
 	if (!uap)
 		return -ENODEV;
 
+	if (uap->port.dev->platform_data) {
+		struct amba_pl011_data *plat;
+
+		plat = uap->port.dev->platform_data;
+		if (plat->init)
+			plat->init();
+	}
+
 	uap->port.uartclk = clk_get_rate(uap->clk);
 
 	if (options)
@@ -1774,6 +1894,7 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
 	uap->lcrh_rx = vendor->lcrh_rx;
 	uap->lcrh_tx = vendor->lcrh_tx;
 	uap->fifosize = vendor->fifosize;
+	uap->interrupt_may_hang = vendor->interrupt_may_hang;
 	uap->port.dev = &dev->dev;
 	uap->port.mapbase = dev->res.start;
 	uap->port.membase = base;
diff --git a/drivers/tty/serial/bcm63xx_uart.c b/drivers/tty/serial/bcm63xx_uart.c
index a1a0e55d0807..c0b68b9cad91 100644
--- a/drivers/tty/serial/bcm63xx_uart.c
+++ b/drivers/tty/serial/bcm63xx_uart.c
@@ -250,6 +250,20 @@ static void bcm_uart_do_rx(struct uart_port *port)
 		/* get overrun/fifo empty information from ier
 		 * register */
 		iestat = bcm_uart_readl(port, UART_IR_REG);
+
+		if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
+			unsigned int val;
+
+			/* fifo reset is required to clear
+			 * interrupt */
+			val = bcm_uart_readl(port, UART_CTL_REG);
+			val |= UART_CTL_RSTRXFIFO_MASK;
+			bcm_uart_writel(port, val, UART_CTL_REG);
+
+			port->icount.overrun++;
+			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+		}
+
 		if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
 			break;
 
@@ -284,10 +298,6 @@ static void bcm_uart_do_rx(struct uart_port *port)
 		if (uart_handle_sysrq_char(port, c))
 			continue;
 
-		if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
-			port->icount.overrun++;
-			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
-		}
 
 		if ((cstat & port->ignore_status_mask) == 0)
 			tty_insert_flip_char(tty, c, flag);
diff --git a/drivers/tty/serial/jsm/jsm_driver.c b/drivers/tty/serial/jsm/jsm_driver.c
index 18f548449c63..96da17868cf3 100644
--- a/drivers/tty/serial/jsm/jsm_driver.c
+++ b/drivers/tty/serial/jsm/jsm_driver.c
@@ -125,7 +125,7 @@ static int __devinit jsm_probe_one(struct pci_dev *pdev, const struct pci_device
 	brd->bd_uart_offset = 0x200;
 	brd->bd_dividend = 921600;
 
-	brd->re_map_membase = ioremap(brd->membase, 0x1000);
+	brd->re_map_membase = ioremap(brd->membase, pci_resource_len(pdev, 0));
 	if (!brd->re_map_membase) {
 		dev_err(&pdev->dev,
 			"card has no PCI Memory resources, "
diff --git a/drivers/tty/serial/s5pv210.c b/drivers/tty/serial/s5pv210.c
index fb2619f93d84..dd194dc80ee9 100644
--- a/drivers/tty/serial/s5pv210.c
+++ b/drivers/tty/serial/s5pv210.c
@@ -30,7 +30,7 @@ static int s5pv210_serial_setsource(struct uart_port *port,
 	struct s3c2410_uartcfg *cfg = port->dev->platform_data;
 	unsigned long ucon = rd_regl(port, S3C2410_UCON);
 
-	if ((cfg->clocks_size) == 1)
+	if (cfg->flags & NO_NEED_CHECK_CLKSRC)
 		return 0;
 
 	if (strcmp(clk->name, "pclk") == 0)
@@ -55,7 +55,7 @@ static int s5pv210_serial_getsource(struct uart_port *port,
 
 	clk->divisor = 1;
 
-	if ((cfg->clocks_size) == 1)
+	if (cfg->flags & NO_NEED_CHECK_CLKSRC)
 		return 0;
 
 	switch (ucon & S5PV210_UCON_CLKMASK) {