Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 691 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/ti/omap/dm816x.dtsi b/arch/arm/boot/dts/ti/omap/dm816x.dtsi
new file mode 100644
index 000000000000..b68686f0643b
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dm816x.dtsi
@@ -0,0 +1,691 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/clock/dm816.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/omap.h>
+
+/ {
+	compatible = "ti,dm816";
+	interrupt-parent = <&intc>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			compatible = "arm,cortex-a8";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+	};
+
+	/*
+	 * The soc node represents the soc top level view. It is used for IPs
+	 * that are not memory mapped in the MPU view or for the MPU itself.
+	 */
+	soc {
+		compatible = "ti,omap-infra";
+		mpu {
+			compatible = "ti,omap3-mpu";
+			ti,hwmods = "mpu";
+		};
+	};
+
+	/*
+	 * XXX: Use a flat representation of the dm816x interconnect.
+	 * The real dm816x interconnect network is quite complex. Since
+	 * it will not bring real advantage to represent that in DT
+	 * for the moment, just use a fake OCP bus entry to represent
+	 * the whole bus hierarchy.
+	 */
+	ocp {
+		compatible = "simple-bus";
+		reg = <0x44000000 0x10000>;
+		interrupts = <9 10>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		prcm: prcm@48180000 {
+			compatible = "ti,dm816-prcm", "simple-bus";
+			reg = <0x48180000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48180000 0x4000>;
+
+			prcm_clocks: clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			prcm_clockdomains: clockdomains {
+			};
+		};
+
+		scrm: scrm@48140000 {
+			compatible = "ti,dm816-scrm", "simple-bus";
+			reg = <0x48140000 0x21000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#pinctrl-cells = <1>;
+			ranges = <0 0x48140000 0x21000>;
+
+			dm816x_pinmux: pinmux@800 {
+				compatible = "pinctrl-single";
+				reg = <0x800 0x50a>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#pinctrl-cells = <1>;
+				pinctrl-single,register-width = <16>;
+				pinctrl-single,function-mask = <0xf>;
+			};
+
+			/* Device Configuration Registers */
+			scm_conf: syscon@600 {
+				compatible = "syscon", "simple-bus";
+				reg = <0x600 0x110>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x600 0x110>;
+
+				usb_phy0: usb-phy@20 {
+					compatible = "ti,dm8168-usb-phy";
+					reg = <0x20 0x8>;
+					reg-names = "phy";
+					clocks = <&main_fapll 6>;
+					clock-names = "refclk";
+					#phy-cells = <0>;
+					syscon = <&scm_conf>;
+				};
+
+				usb_phy1: usb-phy@28 {
+					compatible = "ti,dm8168-usb-phy";
+					reg = <0x28 0x8>;
+					reg-names = "phy";
+					clocks = <&main_fapll 6>;
+					clock-names = "refclk";
+					#phy-cells = <0>;
+					syscon = <&scm_conf>;
+				};
+			};
+
+			scrm_clocks: clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			scrm_clockdomains: clockdomains {
+			};
+		};
+
+		target-module@49000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49000000 0x4>;
+			reg-names = "rev";
+			clocks = <&alwon_clkctrl DM816_TPCC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49000000 0x10000>;
+
+			edma: dma@0 {
+				compatible = "ti,edma3-tpcc";
+				reg = <0 0x10000>;
+				reg-names = "edma3_cc";
+				interrupts = <12 13 14>;
+				interrupt-names = "edma3_ccint", "edma3_mperr",
+						  "edma3_ccerrint";
+				dma-requests = <64>;
+				#dma-cells = <2>;
+
+				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
+					   <&edma_tptc2 3>, <&edma_tptc3 0>;
+
+				ti,edma-memcpy-channels = <20 21>;
+			};
+		};
+
+		target-module@49800000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49800000 0x4>,
+			      <0x49800010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC0_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49800000 0x100000>;
+
+			edma_tptc0: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <112>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49900000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49900000 0x4>,
+			      <0x49900010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49900000 0x100000>;
+
+			edma_tptc1: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <113>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49a00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49a00000 0x4>,
+			      <0x49a00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49a00000 0x100000>;
+
+			edma_tptc2: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <114>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49b00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49b00000 0x4>,
+			      <0x49b00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC3_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49b00000 0x100000>;
+
+			edma_tptc3: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <115>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		elm: elm@48080000 {
+			compatible = "ti,am3352-elm";
+			ti,hwmods = "elm";
+			reg = <0x48080000 0x2000>;
+			interrupts = <4>;
+		};
+
+		gpio1: gpio@48032000 {
+			compatible = "ti,omap4-gpio";
+			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
+			reg = <0x48032000 0x1000>;
+			interrupts = <96>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@4804c000 {
+			compatible = "ti,omap4-gpio";
+			ti,hwmods = "gpio2";
+			ti,gpio-always-on;
+			reg = <0x4804c000 0x1000>;
+			interrupts = <98>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			reg = <0x50000000 0x2000>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			interrupts = <100>;
+			dmas = <&edma 52 0>;
+			dma-names = "rxtx";
+			gpmc,num-cs = <6>;
+			gpmc,num-waitpins = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		i2c1: i2c@48028000 {
+			compatible = "ti,omap4-i2c";
+			ti,hwmods = "i2c1";
+			reg = <0x48028000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <70>;
+		};
+
+		i2c2: i2c@4802a000 {
+			compatible = "ti,omap4-i2c";
+			ti,hwmods = "i2c2";
+			reg = <0x4802a000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <71>;
+		};
+
+		intc: interrupt-controller@48200000 {
+			compatible = "ti,dm816-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x48200000 0x1000>;
+		};
+
+		rtc: rtc@480c0000 {
+			compatible = "ti,am3352-rtc", "ti,da830-rtc";
+			reg = <0x480c0000 0x1000>;
+			interrupts = <75 76>;
+			ti,hwmods = "rtc";
+		};
+
+		mailbox: mailbox@480c8000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x480c8000 0x2000>;
+			interrupts = <77>;
+			ti,hwmods = "mailbox";
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <12>;
+			mbox_dsp: mbox-dsp {
+				ti,mbox-tx = <3 0 0>;
+				ti,mbox-rx = <0 0 0>;
+			};
+		};
+
+		spinbox: spinbox@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x2000>;
+			ti,hwmods = "spinbox";
+			#hwlock-cells = <1>;
+		};
+
+		mdio: mdio@4a100800 {
+			compatible = "ti,davinci_mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4a100800 0x100>;
+			ti,hwmods = "davinci_mdio";
+			bus_freq = <1000000>;
+			phy0: ethernet-phy@0 {
+				reg = <1>;
+			};
+			phy1: ethernet-phy@1 {
+				reg = <2>;
+			};
+		};
+
+		eth0: ethernet@4a100000 {
+			compatible = "ti,dm816-emac";
+			ti,hwmods = "emac0";
+			reg = <0x4a100000 0x800
+			       0x4a100900 0x3700>;
+			clocks = <&sysclk24_ck>;
+			syscon = <&scm_conf>;
+			ti,davinci-ctrl-reg-offset = <0>;
+			ti,davinci-ctrl-mod-reg-offset = <0x900>;
+			ti,davinci-ctrl-ram-offset = <0x2000>;
+			ti,davinci-ctrl-ram-size = <0x2000>;
+			interrupts = <40 41 42 43>;
+			phy-handle = <&phy0>;
+		};
+
+		eth1: ethernet@4a120000 {
+			compatible = "ti,dm816-emac";
+			ti,hwmods = "emac1";
+			reg = <0x4a120000 0x4000>;
+			clocks = <&sysclk24_ck>;
+			syscon = <&scm_conf>;
+			ti,davinci-ctrl-reg-offset = <0>;
+			ti,davinci-ctrl-mod-reg-offset = <0x900>;
+			ti,davinci-ctrl-ram-offset = <0x2000>;
+			ti,davinci-ctrl-ram-size = <0x2000>;
+			interrupts = <44 45 46 47>;
+			phy-handle = <&phy1>;
+		};
+
+		sata: sata@4a140000 {
+			compatible = "ti,dm816-ahci";
+			reg = <0x4a140000 0x10000>;
+			interrupts = <16>;
+			ti,hwmods = "sata";
+		};
+
+		mcspi1: spi@48030000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x48030000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <65>;
+			ti,spi-num-cs = <4>;
+			ti,hwmods = "mcspi1";
+			dmas = <&edma 16 0 &edma 17 0
+				&edma 18 0 &edma 19 0
+				&edma 20 0 &edma 21 0
+				&edma 22 0 &edma 23 0>;
+			dma-names = "tx0", "rx0", "tx1", "rx1",
+				    "tx2", "rx2", "tx3", "rx3";
+		};
+
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x48060000 0x11000>;
+			ti,hwmods = "mmc1";
+			interrupts = <64>;
+			dmas = <&edma 24 0 &edma 25 0>;
+			dma-names = "tx", "rx";
+		};
+
+		timer1_target: target-module@4802e000 {
+			compatible = "ti,sysc-omap4-timer", "ti,sysc";
+			reg = <0x4802e000 0x4>,
+			      <0x4802e010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			clocks = <&alwon_clkctrl DM816_TIMER1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4802e000 0x1000>;
+
+			timer1: timer@0 {
+				compatible = "ti,dm816-timer";
+				reg = <0 0x1000>;
+				interrupts = <67>;
+				ti,timer-alwon;
+				clocks = <&alwon_clkctrl DM816_TIMER1_CLKCTRL 0>;
+				clock-names = "fck";
+			};
+		};
+
+		timer2_target: target-module@48040000 {
+			compatible = "ti,sysc-omap4-timer", "ti,sysc";
+			reg = <0x48040000 0x4>,
+			      <0x48040010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			clocks = <&alwon_clkctrl DM816_TIMER2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x48040000 0x1000>;
+
+			timer2: timer@0 {
+				compatible = "ti,dm816-timer";
+				reg = <0 0x1000>;
+				interrupts = <68>;
+				clocks = <&alwon_clkctrl DM816_TIMER2_CLKCTRL 0>;
+				clock-names = "fck";
+			};
+		};
+
+		timer3: timer@48042000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48042000 0x2000>;
+			interrupts = <69>;
+			ti,hwmods = "timer3";
+		};
+
+		timer4: timer@48044000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48044000 0x2000>;
+			interrupts = <92>;
+			ti,hwmods = "timer4";
+			ti,timer-pwm;
+		};
+
+		timer5: timer@48046000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48046000 0x2000>;
+			interrupts = <93>;
+			ti,hwmods = "timer5";
+			ti,timer-pwm;
+		};
+
+		timer6: timer@48048000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48048000 0x2000>;
+			interrupts = <94>;
+			ti,hwmods = "timer6";
+			ti,timer-pwm;
+		};
+
+		timer7: timer@4804a000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x4804a000 0x2000>;
+			interrupts = <95>;
+			ti,hwmods = "timer7";
+			ti,timer-pwm;
+		};
+
+		uart1: serial@48020000 {
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
+			ti,hwmods = "uart1";
+			reg = <0x48020000 0x2000>;
+			clock-frequency = <48000000>;
+			interrupts = <72>;
+			dmas = <&edma 26 0 &edma 27 0>;
+			dma-names = "tx", "rx";
+		};
+
+		uart2: serial@48022000 {
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
+			ti,hwmods = "uart2";
+			reg = <0x48022000 0x2000>;
+			clock-frequency = <48000000>;
+			interrupts = <73>;
+			dmas = <&edma 28 0 &edma 29 0>;
+			dma-names = "tx", "rx";
+		};
+
+		uart3: serial@48024000 {
+			compatible = "ti,am3352-uart", "ti,omap3-uart";
+			ti,hwmods = "uart3";
+			reg = <0x48024000 0x2000>;
+			clock-frequency = <48000000>;
+			interrupts = <74>;
+			dmas = <&edma 30 0 &edma 31 0>;
+			dma-names = "tx", "rx";
+		};
+
+		/* NOTE: USB needs a transceiver driver for phys to work */
+		usb: usb_otg_hs@47401000 {
+			compatible = "ti,am33xx-usb";
+			reg = <0x47401000 0x400000>;
+			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ti,hwmods = "usb_otg_hs";
+
+			usb0: usb@47401000 {
+				compatible = "ti,musb-dm816";
+				reg = <0x47401400 0x400
+				       0x47401000 0x200>;
+				reg-names = "mc", "control";
+				interrupts = <18>;
+				interrupt-names = "mc";
+				dr_mode = "host";
+				interface-type = <0>;
+				phys = <&usb_phy0>;
+				phy-names = "usb2-phy";
+				mentor,multipoint = <1>;
+				mentor,num-eps = <16>;
+				mentor,ram-bits = <12>;
+				mentor,power = <500>;
+
+				dmas = <&cppi41dma  0 0 &cppi41dma  1 0
+					&cppi41dma  2 0 &cppi41dma  3 0
+					&cppi41dma  4 0 &cppi41dma  5 0
+					&cppi41dma  6 0 &cppi41dma  7 0
+					&cppi41dma  8 0 &cppi41dma  9 0
+					&cppi41dma 10 0 &cppi41dma 11 0
+					&cppi41dma 12 0 &cppi41dma 13 0
+					&cppi41dma 14 0 &cppi41dma  0 1
+					&cppi41dma  1 1 &cppi41dma  2 1
+					&cppi41dma  3 1 &cppi41dma  4 1
+					&cppi41dma  5 1 &cppi41dma  6 1
+					&cppi41dma  7 1 &cppi41dma  8 1
+					&cppi41dma  9 1 &cppi41dma 10 1
+					&cppi41dma 11 1 &cppi41dma 12 1
+					&cppi41dma 13 1 &cppi41dma 14 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
+			};
+
+			usb1: usb@47401800 {
+				compatible = "ti,musb-dm816";
+				reg = <0x47401c00 0x400
+				       0x47401800 0x200>;
+				reg-names = "mc", "control";
+				interrupts = <19>;
+				interrupt-names = "mc";
+				dr_mode = "host";
+				interface-type = <0>;
+				phys = <&usb_phy1>;
+				phy-names = "usb2-phy";
+				mentor,multipoint = <1>;
+				mentor,num-eps = <16>;
+				mentor,ram-bits = <12>;
+				mentor,power = <500>;
+
+				dmas = <&cppi41dma 15 0 &cppi41dma 16 0
+					&cppi41dma 17 0 &cppi41dma 18 0
+					&cppi41dma 19 0 &cppi41dma 20 0
+					&cppi41dma 21 0 &cppi41dma 22 0
+					&cppi41dma 23 0 &cppi41dma 24 0
+					&cppi41dma 25 0 &cppi41dma 26 0
+					&cppi41dma 27 0 &cppi41dma 28 0
+					&cppi41dma 29 0 &cppi41dma 15 1
+					&cppi41dma 16 1 &cppi41dma 17 1
+					&cppi41dma 18 1 &cppi41dma 19 1
+					&cppi41dma 20 1 &cppi41dma 21 1
+					&cppi41dma 22 1 &cppi41dma 23 1
+					&cppi41dma 24 1 &cppi41dma 25 1
+					&cppi41dma 26 1 &cppi41dma 27 1
+					&cppi41dma 28 1 &cppi41dma 29 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
+			};
+
+			cppi41dma: dma-controller@47402000 {
+				compatible = "ti,am3359-cppi41";
+				reg =  <0x47400000 0x1000
+					0x47402000 0x1000
+					0x47403000 0x1000
+					0x47404000 0x4000>;
+				reg-names = "glue", "controller", "scheduler", "queuemgr";
+				interrupts = <17>;
+				interrupt-names = "glue";
+				#dma-cells = <2>;
+				/* For backwards compatibility: */
+				#dma-channels = <30>;
+				dma-channels = <30>;
+				#dma-requests = <256>;
+				dma-requests = <256>;
+			};
+		};
+
+		wd_timer2: wd_timer@480c2000 {
+			compatible = "ti,omap3-wdt";
+			ti,hwmods = "wd_timer";
+			reg = <0x480c2000 0x1000>;
+			interrupts = <0>;
+		};
+	};
+};
+
+#include "dm816x-clocks.dtsi"
+
+/* Preferred always-on timer for clocksource */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer1_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer2_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};