diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2021-09-01 02:43:06 +0300 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2021-09-01 02:43:06 +0300 |
| commit | 9e9fb7655ed585da8f468e29221f0ba194a5f613 (patch) | |
| tree | d2c51887389b8297635a5b90d5766897f00fe928 /Documentation | |
| parent | 86ac54e79fe09b34c52691a780a6e31d12fa57f4 (diff) | |
| parent | 29ce8f9701072fc221d9c38ad952de1a9578f95c (diff) | |
| download | linux-9e9fb7655ed585da8f468e29221f0ba194a5f613.tar.xz | |
Merge tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read out
again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs in
kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by the
router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105):
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver"
* tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1715 commits)
net: Add depends on OF_NET for LiteX's LiteETH
ipv6: seg6: remove duplicated include
net: hns3: remove unnecessary spaces
net: hns3: add some required spaces
net: hns3: clean up a type mismatch warning
net: hns3: refine function hns3_set_default_feature()
ipv6: remove duplicated 'net/lwtunnel.h' include
net: w5100: check return value after calling platform_get_resource()
net/mlxbf_gige: Make use of devm_platform_ioremap_resourcexxx()
net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()
net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()
fou: remove sparse errors
ipv4: fix endianness issue in inet_rtm_getroute_build_skb()
octeontx2-af: Set proper errorcode for IPv4 checksum errors
octeontx2-af: Fix static code analyzer reported issues
octeontx2-af: Fix mailbox errors in nix_rss_flowkey_cfg
octeontx2-af: Fix loop in free and unmap counter
af_unix: fix potential NULL deref in unix_dgram_connect()
dpaa2-eth: Replace strlcpy with strscpy
octeontx2-af: Use NDC TX for transmit packet data
...
Diffstat (limited to 'Documentation')
44 files changed, 1440 insertions, 561 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 56bd70ee82fa..2102467faad6 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -4962,8 +4962,6 @@ sa1100ir [NET] See drivers/net/irda/sa1100_ir.c. - sbni= [NET] Granch SBNI12 leased line adapter - sched_verbose [KNL] Enables verbose scheduler debug messages. schedstats= [KNL,X86] Enable or disable scheduled statistics. diff --git a/Documentation/bpf/index.rst b/Documentation/bpf/index.rst index baea6c2abba5..1ceb5d704a97 100644 --- a/Documentation/bpf/index.rst +++ b/Documentation/bpf/index.rst @@ -15,15 +15,7 @@ that goes into great technical depth about the BPF Architecture. libbpf ====== -Libbpf is a userspace library for loading and interacting with bpf programs. - -.. toctree:: - :maxdepth: 1 - - libbpf/libbpf - libbpf/libbpf_api - libbpf/libbpf_build - libbpf/libbpf_naming_convention +Documentation/bpf/libbpf/libbpf.rst is a userspace library for loading and interacting with bpf programs. BPF Type Format (BTF) ===================== diff --git a/Documentation/bpf/libbpf/libbpf.rst b/Documentation/bpf/libbpf/index.rst index 1b1e61d5ead1..4f8adfc3ab83 100644 --- a/Documentation/bpf/libbpf/libbpf.rst +++ b/Documentation/bpf/libbpf/index.rst @@ -3,6 +3,14 @@ libbpf ====== +For API documentation see the `versioned API documentation site <https://libbpf.readthedocs.io/en/latest/api.html>`_. + +.. toctree:: + :maxdepth: 1 + + libbpf_naming_convention + libbpf_build + This is documentation for libbpf, a userspace library for loading and interacting with bpf programs. diff --git a/Documentation/bpf/libbpf/libbpf_api.rst b/Documentation/bpf/libbpf/libbpf_api.rst deleted file mode 100644 index f07eecd054da..000000000000 --- a/Documentation/bpf/libbpf/libbpf_api.rst +++ /dev/null @@ -1,27 +0,0 @@ -.. SPDX-License-Identifier: (LGPL-2.1 OR BSD-2-Clause) - -API -=== - -This documentation is autogenerated from header files in libbpf, tools/lib/bpf - -.. kernel-doc:: tools/lib/bpf/libbpf.h - :internal: - -.. kernel-doc:: tools/lib/bpf/bpf.h - :internal: - -.. kernel-doc:: tools/lib/bpf/btf.h - :internal: - -.. kernel-doc:: tools/lib/bpf/xsk.h - :internal: - -.. kernel-doc:: tools/lib/bpf/bpf_tracing.h - :internal: - -.. kernel-doc:: tools/lib/bpf/bpf_core_read.h - :internal: - -.. kernel-doc:: tools/lib/bpf/bpf_endian.h - :internal:
\ No newline at end of file diff --git a/Documentation/bpf/libbpf/libbpf_naming_convention.rst b/Documentation/bpf/libbpf/libbpf_naming_convention.rst index 6bf9c5ac7576..9c68d5014ff1 100644 --- a/Documentation/bpf/libbpf/libbpf_naming_convention.rst +++ b/Documentation/bpf/libbpf/libbpf_naming_convention.rst @@ -69,7 +69,7 @@ functions. These can be mixed and matched. Note that these functions are not reentrant for performance reasons. ABI -========== +--- libbpf can be both linked statically or used as DSO. To avoid possible conflicts with other libraries an application is linked with, all diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt deleted file mode 100644 index e15589f47787..000000000000 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ /dev/null @@ -1,43 +0,0 @@ -* Broadcom UniMAC MDIO bus controller - -Required properties: -- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", - "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5" or - "brcm,unimac-mdio" -- reg: address and length of the register set for the device, first one is the - base register, and the second one is optional and for indirect accesses to - larger than 16-bits MDIO transactions -- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" -- #size-cells: must be 1 -- #address-cells: must be 0 - -Optional properties: -- interrupts: must be one if the interrupt is shared with the Ethernet MAC or - Ethernet switch this MDIO block is integrated from, or must be two, if there - are two separate interrupts, first one must be "mdio done" and second must be - for "mdio error" -- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed - to this hardware block, or must be "mdio_done" for the first interrupt and - "mdio_error" for the second when there are separate interrupts -- clocks: A reference to the clock supplying the MDIO bus controller -- clock-frequency: the MDIO bus clock that must be output by the MDIO bus - hardware, if absent, the default hardware values are used - -Child nodes of this MDIO bus controller node are standard Ethernet PHY device -nodes as described in Documentation/devicetree/bindings/net/phy.txt - -Example: - -mdio@403c0 { - compatible = "brcm,unimac-mdio"; - reg = <0x403c0 0x8 0x40300 0x18>; - reg-names = "mdio", "mdio_indir_rw"; - #size-cells = <1>; - #address-cells = <0>; - - ... - phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.yaml b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.yaml new file mode 100644 index 000000000000..f4f4c37f1d4e --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/brcm,unimac-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom UniMAC MDIO bus controller + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +allOf: + - $ref: mdio.yaml# + +properties: + compatible: + enum: + - brcm,genet-mdio-v1 + - brcm,genet-mdio-v2 + - brcm,genet-mdio-v3 + - brcm,genet-mdio-v4 + - brcm,genet-mdio-v5 + - brcm,unimac-mdio + + reg: + minItems: 1 + items: + - description: base register + - description: indirect accesses to larger than 16-bits MDIO transactions + + reg-names: + minItems: 1 + items: + - const: mdio + - const: mdio_indir_rw + + interrupts: + oneOf: + - description: > + Interrupt shared with the Ethernet MAC or Ethernet switch this MDIO + block is integrated from + - items: + - description: | + "mdio done" interrupt + - description: | + "mdio error" interrupt + + interrupt-names: + oneOf: + - const: mdio_done_error + - items: + - const: mdio_done + - const: mdio_error + + clocks: + description: A reference to the clock supplying the MDIO bus controller + + clock-frequency: + description: > + The MDIO bus clock that must be output by the MDIO bus hardware, if + absent, the default hardware values are used + +unevaluatedProperties: false + +required: + - reg + - reg-names + - '#address-cells' + - '#size-cells' + +examples: + - | + mdio@403c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x403c0 0x8>, <0x40300 0x18>; + reg-names = "mdio", "mdio_indir_rw"; + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/can/bosch,c_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,c_can.yaml new file mode 100644 index 000000000000..2cd145a642f1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/bosch,c_can.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/can/bosch,c_can.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bosch C_CAN/D_CAN controller Device Tree Bindings + +description: Bosch C_CAN/D_CAN controller for CAN bus + +maintainers: + - Dario Binacchi <dariobin@libero.it> + +allOf: + - $ref: can-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - bosch,c_can + - bosch,d_can + - ti,dra7-d_can + - ti,am3352-d_can + - items: + - enum: + - ti,am4372-d_can + - const: ti,am3352-d_can + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 4 + + power-domains: + description: | + Should contain a phandle to a PM domain provider node and an args + specifier containing the DCAN device id value. It's mandatory for + Keystone 2 66AK2G SoCs only. + maxItems: 1 + + clocks: + description: | + CAN functional clock phandle. + maxItems: 1 + + clock-names: + maxItems: 1 + + syscon-raminit: + description: | + Handle to system control region that contains the RAMINIT register, + register offset to the RAMINIT register and the CAN instance number (0 + offset). + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: The phandle to the system control region. + - description: The register offset. + - description: The CAN instance number. + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +if: + properties: + compatible: + contains: + enum: + - bosch,d_can + +then: + properties: + interrupts: + minItems: 4 + maxItems: 4 + items: + - description: Error and status IRQ + - description: Message object IRQ + - description: RAM ECC correctable error IRQ + - description: RAM ECC non-correctable error IRQ + +else: + properties: + interrupts: + maxItems: 1 + items: + - description: Error and status IRQ + +additionalProperties: false + +examples: + - | + #include <dt-bindings/reset/altr,rst-mgr.h> + + can@ffc00000 { + compatible = "bosch,d_can"; + reg = <0xffc00000 0x1000>; + interrupts = <0 131 4>, <0 132 4>, <0 133 4>, <0 134 4>; + clocks = <&can0_clk>; + resets = <&rst CAN0_RESET>; + }; + - | + can@0 { + compatible = "ti,am3352-d_can"; + reg = <0x0 0x2000>; + clocks = <&dcan1_fck>; + clock-names = "fck"; + syscon-raminit = <&scm_conf 0x644 1>; + interrupts = <55>; + }; diff --git a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml index f84e31348d80..fb547e26c676 100644 --- a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml +++ b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml @@ -104,9 +104,18 @@ properties: maximum: 32 maxItems: 1 + power-domains: + description: + Power domain provider node and an args specifier containing + the can device id value. + maxItems: 1 + can-transceiver: $ref: can-transceiver.yaml# + phys: + maxItems: 1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt deleted file mode 100644 index 366479806acb..000000000000 --- a/Documentation/devicetree/bindings/net/can/c_can.txt +++ /dev/null @@ -1,65 +0,0 @@ -Bosch C_CAN/D_CAN controller Device Tree Bindings -------------------------------------------------- - -Required properties: -- compatible : Should be "bosch,c_can" for C_CAN controllers and - "bosch,d_can" for D_CAN controllers. - Can be "ti,dra7-d_can", "ti,am3352-d_can" or - "ti,am4372-d_can". -- reg : physical base address and size of the C_CAN/D_CAN - registers map -- interrupts : property with a value describing the interrupt - number - -The following are mandatory properties for DRA7x, AM33xx and AM43xx SoCs only: -- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the - instance number - -The following are mandatory properties for Keystone 2 66AK2G SoCs only: -- power-domains : Should contain a phandle to a PM domain provider node - and an args specifier containing the DCAN device id - value. This property is as per the binding, - Documentation/devicetree/bindings/soc/ti/sci-pm-domain.yaml -- clocks : CAN functional clock phandle. This property is as per the - binding, - Documentation/devicetree/bindings/clock/ti,sci-clk.yaml - -Optional properties: -- syscon-raminit : Handle to system control region that contains the - RAMINIT register, register offset to the RAMINIT - register and the CAN instance number (0 offset). - -Note: "ti,hwmods" field is used to fetch the base address and irq -resources from TI, omap hwmod data base during device registration. -Future plan is to migrate hwmod data base contents into device tree -blob so that, all the required data will be used from device tree dts -file. - -Example: - -Step1: SoC common .dtsi file - - dcan1: d_can@481d0000 { - compatible = "bosch,d_can"; - reg = <0x481d0000 0x2000>; - interrupts = <55>; - interrupt-parent = <&intc>; - status = "disabled"; - }; - -(or) - - dcan1: d_can@481d0000 { - compatible = "bosch,d_can"; - ti,hwmods = "d_can1"; - reg = <0x481d0000 0x2000>; - interrupts = <55>; - interrupt-parent = <&intc>; - status = "disabled"; - }; - -Step 2: board specific .dts file - - &dcan1 { - status = "okay"; - }; diff --git a/Documentation/devicetree/bindings/net/can/can-controller.yaml b/Documentation/devicetree/bindings/net/can/can-controller.yaml index 9cf2ae097156..1f0e98051074 100644 --- a/Documentation/devicetree/bindings/net/can/can-controller.yaml +++ b/Documentation/devicetree/bindings/net/can/can-controller.yaml @@ -13,6 +13,15 @@ properties: $nodename: pattern: "^can(@.*)?$" + termination-gpios: + description: GPIO pin to enable CAN bus termination. + maxItems: 1 + + termination-ohms: + description: The resistance value of the CAN bus termination resistor. + minimum: 1 + maximum: 65535 + additionalProperties: true ... diff --git a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml index 55bff1586b6f..3f0ee17c1461 100644 --- a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml +++ b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml @@ -119,6 +119,9 @@ properties: minimum: 0 maximum: 2 + termination-gpios: true + termination-ohms: true + required: - compatible - reg @@ -148,3 +151,17 @@ examples: fsl,stop-mode = <&gpr 0x34 28>; fsl,scu-index = /bits/ 8 <1>; }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + + can@2090000 { + compatible = "fsl,imx6q-flexcan"; + reg = <0x02090000 0x4000>; + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 1>, <&clks 2>; + clock-names = "ipg", "per"; + fsl,stop-mode = <&gpr 0x34 28>; + termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + termination-ohms = <120>; + }; diff --git a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml index 0b33ba9ccb47..546c6e6d2fb0 100644 --- a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml +++ b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml @@ -30,13 +30,15 @@ properties: - renesas,r8a77995-canfd # R-Car D3 - const: renesas,rcar-gen3-canfd # R-Car Gen3 and RZ/G2 + - items: + - enum: + - renesas,r9a07g044-canfd # RZ/G2{L,LC} + - const: renesas,rzg2l-canfd # RZ/G2L family + reg: maxItems: 1 - interrupts: - items: - - description: Channel interrupt - - description: Global interrupt + interrupts: true clocks: maxItems: 3 @@ -50,8 +52,7 @@ properties: power-domains: maxItems: 1 - resets: - maxItems: 1 + resets: true renesas,no-can-fd: $ref: /schemas/types.yaml#/definitions/flag @@ -91,6 +92,62 @@ required: - channel0 - channel1 +if: + properties: + compatible: + contains: + enum: + - renesas,rzg2l-canfd +then: + properties: + interrupts: + items: + - description: CAN global error interrupt + - description: CAN receive FIFO interrupt + - description: CAN0 error interrupt + - description: CAN0 transmit interrupt + - description: CAN0 transmit/receive FIFO receive completion interrupt + - description: CAN1 error interrupt + - description: CAN1 transmit interrupt + - description: CAN1 transmit/receive FIFO receive completion interrupt + + interrupt-names: + items: + - const: g_err + - const: g_recc + - const: ch0_err + - const: ch0_rec + - const: ch0_trx + - const: ch1_err + - const: ch1_rec + - const: ch1_trx + + resets: + maxItems: 2 + + reset-names: + items: + - const: rstp_n + - const: rstc_n + + required: + - interrupt-names + - reset-names +else: + properties: + interrupts: + items: + - description: Channel interrupt + - description: Global interrupt + + interrupt-names: + items: + - const: ch_int + - const: g_int + + resets: + maxItems: 1 + unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/net/fsl,fec.yaml b/Documentation/devicetree/bindings/net/fsl,fec.yaml new file mode 100644 index 000000000000..eca41443fcce --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl,fec.yaml @@ -0,0 +1,244 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/fsl,fec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Fast Ethernet Controller (FEC) + +maintainers: + - Joakim Zhang <qiangqing.zhang@nxp.com> + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - fsl,imx25-fec + - fsl,imx27-fec + - fsl,imx28-fec + - fsl,imx6q-fec + - fsl,mvf600-fec + - items: + - enum: + - fsl,imx53-fec + - fsl,imx6sl-fec + - const: fsl,imx25-fec + - items: + - enum: + - fsl,imx35-fec + - fsl,imx51-fec + - const: fsl,imx27-fec + - items: + - enum: + - fsl,imx6ul-fec + - fsl,imx6sx-fec + - const: fsl,imx6q-fec + - items: + - enum: + - fsl,imx7d-fec + - const: fsl,imx6sx-fec + - items: + - const: fsl,imx8mq-fec + - const: fsl,imx6sx-fec + - items: + - enum: + - fsl,imx8mm-fec + - fsl,imx8mn-fec + - fsl,imx8mp-fec + - const: fsl,imx8mq-fec + - const: fsl,imx6sx-fec + - items: + - const: fsl,imx8qm-fec + - const: fsl,imx6sx-fec + - items: + - enum: + - fsl,imx8qxp-fec + - const: fsl,imx8qm-fec + - const: fsl,imx6sx-fec + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 4 + + interrupt-names: + oneOf: + - items: + - const: int0 + - items: + - const: int0 + - const: pps + - items: + - const: int0 + - const: int1 + - const: int2 + - items: + - const: int0 + - const: int1 + - const: int2 + - const: pps + + clocks: + minItems: 2 + maxItems: 5 + description: + The "ipg", for MAC ipg_clk_s, ipg_clk_mac_s that are for register accessing. + The "ahb", for MAC ipg_clk, ipg_clk_mac that are bus clock. + The "ptp"(option), for IEEE1588 timer clock that requires the clock. + The "enet_clk_ref"(option), for MAC transmit/receiver reference clock like + RGMII TXC clock or RMII reference clock. It depends on board design, + the clock is required if RGMII TXC and RMII reference clock source from + SOC internal PLL. + The "enet_out"(option), output clock for external device, like supply clock + for PHY. The clock is required if PHY clock source from SOC. + The "enet_2x_txclk"(option), for RGMII sampling clock which fixed at 250Mhz. + The clock is required if SoC RGMII enable clock delay. + + clock-names: + minItems: 2 + maxItems: 5 + items: + enum: + - ipg + - ahb + - ptp + - enet_clk_ref + - enet_out + - enet_2x_txclk + + phy-mode: true + + phy-handle: true + + fixed-link: true + + local-mac-address: true + + mac-address: true + + tx-internal-delay-ps: + enum: [0, 2000] + + rx-internal-delay-ps: + enum: [0, 2000] + + phy-supply: + description: + Regulator that powers the Ethernet PHY. + + fsl,num-tx-queues: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The property is valid for enet-avb IP, which supports hw multi queues. + Should specify the tx queue number, otherwise set tx queue number to 1. + enum: [1, 2, 3] + + fsl,num-rx-queues: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The property is valid for enet-avb IP, which supports hw multi queues. + Should specify the rx queue number, otherwise set rx queue number to 1. + enum: [1, 2, 3] + + fsl,magic-packet: + $ref: /schemas/types.yaml#/definitions/flag + description: + If present, indicates that the hardware supports waking up via magic packet. + + fsl,err006687-workaround-present: + $ref: /schemas/types.yaml#/definitions/flag + description: + If present indicates that the system has the hardware workaround for + ERR006687 applied and does not need a software workaround. + + fsl,stop-mode: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Register bits of stop mode control, the format is <&gpr req_gpr req_bit>. + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset for ENET stop request. + req_bit is the gpr bit offset for ENET stop request. + + mdio: + type: object + description: + Specifies the mdio bus in the FEC, used as a container for phy nodes. + + # Deprecated optional properties: + # To avoid these, create a phy node according to ethernet-phy.yaml in the same + # directory, and point the FEC's "phy-handle" property to it. Then use + # the phy's reset binding, again described by ethernet-phy.yaml. + + phy-reset-gpios: + deprecated: true + description: + Should specify the gpio for phy reset. + + phy-reset-duration: + deprecated: true + description: + Reset duration in milliseconds. Should present only if property + "phy-reset-gpios" is available. Missing the property will have the + duration be 1 millisecond. Numbers greater than 1000 are invalid + and 1 millisecond will be used instead. + + phy-reset-active-high: + deprecated: true + description: + If present then the reset sequence using the GPIO specified in the + "phy-reset-gpios" property is reversed (H=reset state, L=operation state). + + phy-reset-post-delay: + deprecated: true + description: + Post reset delay in milliseconds. If present then a delay of phy-reset-post-delay + milliseconds will be observed after the phy-reset-gpios has been toggled. + Can be omitted thus no delay is observed. Delay is in range of 1ms to 1000ms. + Other delays are invalid. + +required: + - compatible + - reg + - interrupts + +# FIXME: We had better set additionalProperties to false to avoid invalid or at +# least undocumented properties. However, PHY may have a deprecated option to +# place PHY OF properties in the MAC node, such as Micrel PHY, and we can find +# these boards which is based on i.MX6QDL. +additionalProperties: false + +examples: + - | + ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; + phy-supply = <®_fec_supply>; + }; + + ethernet@83fed000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fed000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; + phy-supply = <®_fec_supply>; + phy-handle = <ðphy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt deleted file mode 100644 index 9b543789cd52..000000000000 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ /dev/null @@ -1,95 +0,0 @@ -* Freescale Fast Ethernet Controller (FEC) - -Required properties: -- compatible : Should be "fsl,<soc>-fec" -- reg : Address and length of the register set for the device -- interrupts : Should contain fec interrupt -- phy-mode : See ethernet.txt file in the same directory - -Optional properties: -- phy-supply : regulator that powers the Ethernet PHY. -- phy-handle : phandle to the PHY device connected to this device. -- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. - Use instead of phy-handle. -- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports - hw multi queues. Should specify the tx queue number, otherwise set tx queue - number to 1. -- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports - hw multi queues. Should specify the rx queue number, otherwise set rx queue - number to 1. -- fsl,magic-packet : If present, indicates that the hardware supports waking - up via magic packet. -- fsl,err006687-workaround-present: If present indicates that the system has - the hardware workaround for ERR006687 applied and does not need a software - workaround. -- fsl,stop-mode: register bits of stop mode control, the format is - <&gpr req_gpr req_bit>. - gpr is the phandle to general purpose register node. - req_gpr is the gpr register offset for ENET stop request. - req_bit is the gpr bit offset for ENET stop request. - -interrupt-names: names of the interrupts listed in interrupts property in - the same order. The defaults if not specified are - __Number of interrupts__ __Default__ - 1 "int0" - 2 "int0", "pps" - 3 "int0", "int1", "int2" - 4 "int0", "int1", "int2", "pps" - The order may be changed as long as they correspond to the interrupts - property. Currently, only i.mx7 uses "int1" and "int2". They correspond to - tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts. - For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse - per second interrupt associated with 1588 precision time protocol(PTP). - -Optional subnodes: -- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes - according to phy.txt in the same directory - -Deprecated optional properties: - To avoid these, create a phy node according to phy.txt in the same - directory, and point the fec's "phy-handle" property to it. Then use - the phy's reset binding, again described by phy.txt. -- phy-reset-gpios : Should specify the gpio for phy reset -- phy-reset-duration : Reset duration in milliseconds. Should present - only if property "phy-reset-gpios" is available. Missing the property - will have the duration be 1 millisecond. Numbers greater than 1000 are - invalid and 1 millisecond will be used instead. -- phy-reset-active-high : If present then the reset sequence using the GPIO - specified in the "phy-reset-gpios" property is reversed (H=reset state, - L=operation state). -- phy-reset-post-delay : Post reset delay in milliseconds. If present then - a delay of phy-reset-post-delay milliseconds will be observed after the - phy-reset-gpios has been toggled. Can be omitted thus no delay is - observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. - -Example: - -ethernet@83fec000 { - compatible = "fsl,imx51-fec", "fsl,imx27-fec"; - reg = <0x83fec000 0x4000>; - interrupts = <87>; - phy-mode = "mii"; - phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ - local-mac-address = [00 04 9F 01 1B B9]; - phy-supply = <®_fec_supply>; -}; - -Example with phy specified: - -ethernet@83fec000 { - compatible = "fsl,imx51-fec", "fsl,imx27-fec"; - reg = <0x83fec000 0x4000>; - interrupts = <87>; - phy-mode = "mii"; - phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ - local-mac-address = [00 04 9F 01 1B B9]; - phy-supply = <®_fec_supply>; - phy-handle = <ðphy>; - mdio { - clock-frequency = <5000000>; - ethphy: ethernet-phy@6 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <6>; - max-speed = <100>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/intel,ixp46x-ptp-timer.yaml b/Documentation/devicetree/bindings/net/intel,ixp46x-ptp-timer.yaml new file mode 100644 index 000000000000..8b9b3f915d92 --- /dev/null +++ b/Documentation/devicetree/bindings/net/intel,ixp46x-ptp-timer.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2018 Linaro Ltd. +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/intel,ixp46x-ptp-timer.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Intel IXP46x PTP Timer (TSYNC) + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The Intel IXP46x PTP timer is known in the manual as IEEE1588 Hardware + Assist and Time Synchronization Hardware Assist TSYNC provides a PTP + timer. It exists in the Intel IXP45x and IXP46x XScale SoCs. + +properties: + compatible: + const: intel,ixp46x-ptp-timer + + reg: + maxItems: 1 + + interrupts: + items: + - description: Interrupt to trigger master mode snapshot from the + PRP timer, usually a GPIO interrupt. + - description: Interrupt to trigger slave mode snapshot from the + PRP timer, usually a GPIO interrupt. + + interrupt-names: + items: + - const: master + - const: slave + +required: + - compatible + - reg + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + ptp-timer@c8010000 { + compatible = "intel,ixp46x-ptp-timer"; + reg = <0xc8010000 0x1000>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>, <7 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "master", "slave"; + }; diff --git a/Documentation/devicetree/bindings/net/litex,liteeth.yaml b/Documentation/devicetree/bindings/net/litex,liteeth.yaml new file mode 100644 index 000000000000..76c164a8199a --- /dev/null +++ b/Documentation/devicetree/bindings/net/litex,liteeth.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/litex,liteeth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LiteX LiteETH ethernet device + +maintainers: + - Joel Stanley <joel@jms.id.au> + +description: | + LiteETH is a small footprint and configurable Ethernet core for FPGA based + system on chips. + + The hardware source is Open Source and can be found on at + https://github.com/enjoy-digital/liteeth/. + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + const: litex,liteeth + + reg: + items: + - description: MAC registers + - description: MDIO registers + - description: Packet buffer + + reg-names: + items: + - const: mac + - const: mdio + - const: buffer + + interrupts: + maxItems: 1 + + litex,rx-slots: + description: Number of slots in the receive buffer + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + default: 2 + + litex,tx-slots: + description: Number of slots in the transmit buffer + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + default: 2 + + litex,slot-size: + description: Size in bytes of a slot in the tx/rx buffer + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x800 + default: 0x800 + + mac-address: true + local-mac-address: true + phy-handle: true + + mdio: + $ref: mdio.yaml# + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + mac: ethernet@8020000 { + compatible = "litex,liteeth"; + reg = <0x8021000 0x100>, + <0x8020800 0x100>, + <0x8030000 0x2000>; + reg-names = "mac", "mdio", "buffer"; + litex,rx-slots = <2>; + litex,tx-slots = <2>; + litex,slot-size = <0x800>; + interrupts = <0x11 0x1>; + phy-handle = <ð_phy>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + eth_phy: ethernet-phy@0 { + reg = <0>; + }; + }; + }; +... + +# vim: set ts=2 sw=2 sts=2 tw=80 et cc=80 ft=yaml : diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index a4d547efc32a..af9df2f01a1c 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -8,6 +8,7 @@ Required properties: Use "cdns,np4-macb" for NP4 SoC devices. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs. + Use "atmel,sama5d29-gem" for GEM XL IP (10/100) available on Atmel sama5d29 SoCs. Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml index ed88ba4b94df..b8a0b392b24e 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml @@ -87,16 +87,24 @@ properties: - const: ipa-setup-ready interconnects: - items: - - description: Interconnect path between IPA and main memory - - description: Interconnect path between IPA and internal memory - - description: Interconnect path between IPA and the AP subsystem + oneOf: + - items: + - description: Path leading to system memory + - description: Path between the AP and IPA config space + - items: + - description: Path leading to system memory + - description: Path leading to internal memory + - description: Path between the AP and IPA config space interconnect-names: - items: - - const: memory - - const: imem - - const: config + oneOf: + - items: + - const: memory + - const: config + - items: + - const: memory + - const: imem + - const: config qcom,smem-states: $ref: /schemas/types.yaml#/definitions/phandle-array diff --git a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml index 0c973310ada0..2af304341772 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml @@ -14,7 +14,9 @@ allOf: properties: compatible: - const: qcom,ipq4019-mdio + enum: + - qcom,ipq4019-mdio + - qcom,ipq5018-mdio "#address-cells": const: 1 @@ -23,7 +25,18 @@ properties: const: 0 reg: + minItems: 1 + maxItems: 2 + description: + the first Address and length of the register set for the MDIO controller. + the second Address and length of the register for ethernet LDO, this second + address range is only required by the platform IPQ50xx. + + clocks: maxItems: 1 + description: | + MDIO clock source frequency fixed to 100MHZ, this clock should be specified + by the platform IPQ807x, IPQ60xx and IPQ50xx. required: - compatible diff --git a/Documentation/driver-api/nfc/nfc-hci.rst b/Documentation/driver-api/nfc/nfc-hci.rst index eb8a1a14e919..f10fe53aa9fe 100644 --- a/Documentation/driver-api/nfc/nfc-hci.rst +++ b/Documentation/driver-api/nfc/nfc-hci.rst @@ -181,7 +181,7 @@ xmit_from_hci(): The llc must be registered with nfc before it can be used. Do that by calling:: - nfc_llc_register(const char *name, struct nfc_llc_ops *ops); + nfc_llc_register(const char *name, const struct nfc_llc_ops *ops); Again, note that the llc does not handle the physical link. It is thus very easy to mix any physical link with any llc for a given chip driver. diff --git a/Documentation/networking/batman-adv.rst b/Documentation/networking/batman-adv.rst index 74821d29a22f..b85563ea3682 100644 --- a/Documentation/networking/batman-adv.rst +++ b/Documentation/networking/batman-adv.rst @@ -157,7 +157,7 @@ Contact Please send us comments, experiences, questions, anything :) IRC: - #batman on irc.freenode.org + #batadv on ircs://irc.hackint.org/ Mailing-list: b.a.t.m.a.n@open-mesh.org (optional subscription at https://lists.open-mesh.org/mailman3/postorius/lists/b.a.t.m.a.n.lists.open-mesh.org/) diff --git a/Documentation/networking/bonding.rst b/Documentation/networking/bonding.rst index 62f2aab8eaec..31cfd7d674a6 100644 --- a/Documentation/networking/bonding.rst +++ b/Documentation/networking/bonding.rst @@ -501,6 +501,18 @@ fail_over_mac This option was added in bonding version 3.2.0. The "follow" policy was added in bonding version 3.3.0. +lacp_active + Option specifying whether to send LACPDU frames periodically. + + off or 0 + LACPDU frames acts as "speak when spoken to". + + on or 1 + LACPDU frames are sent along the configured links + periodically. See lacp_rate for more details. + + The default is on. + lacp_rate Option specifying the rate in which we'll ask our link partner diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/index.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/index.rst index ee40fcc5ddff..62f4a4aff6ec 100644 --- a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/index.rst +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/index.rst @@ -9,3 +9,4 @@ DPAA2 Documentation dpio-driver ethernet-driver mac-phy-support + switch-driver diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst new file mode 100644 index 000000000000..8bf411b857d4 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst @@ -0,0 +1,217 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +=================== +DPAA2 Switch driver +=================== + +:Copyright: |copy| 2021 NXP + +The DPAA2 Switch driver probes on the Datapath Switch (DPSW) object which can +be instantiated on the following DPAA2 SoCs and their variants: LS2088A and +LX2160A. + +The driver uses the switch device driver model and exposes each switch port as +a network interface, which can be included in a bridge or used as a standalone +interface. Traffic switched between ports is offloaded into the hardware. + +The DPSW can have ports connected to DPNIs or to DPMACs for external access. +:: + + [ethA] [ethB] [ethC] [ethD] [ethE] [ethF] + : : : : : : + : : : : : : + [dpaa2-eth] [dpaa2-eth] [ dpaa2-switch ] + : : : : : : kernel + ============================================================================= + : : : : : : hardware + [DPNI] [DPNI] [============= DPSW =================] + | | | | | | + | ---------- | [DPMAC] [DPMAC] + ------------------------------- | | + | | + [PHY] [PHY] + +Creating an Ethernet Switch +=========================== + +The dpaa2-switch driver probes on DPSW devices found on the fsl-mc bus. These +devices can be either created statically through the boot time configuration +file - DataPath Layout (DPL) - or at runtime using the DPAA2 object APIs +(incorporated already into the restool userspace tool). + +At the moment, the dpaa2-switch driver imposes the following restrictions on +the DPSW object that it will probe: + + * The minimum number of FDBs should be at least equal to the number of switch + interfaces. This is necessary so that separation of switch ports can be + done, ie when not under a bridge, each switch port will have its own FDB. + :: + + fsl_dpaa2_switch dpsw.0: The number of FDBs is lower than the number of ports, cannot probe + + * Both the broadcast and flooding configuration should be per FDB. This + enables the driver to restrict the broadcast and flooding domains of each + FDB depending on the switch ports that are sharing it (aka are under the + same bridge). + :: + + fsl_dpaa2_switch dpsw.0: Flooding domain is not per FDB, cannot probe + fsl_dpaa2_switch dpsw.0: Broadcast domain is not per FDB, cannot probe + + * The control interface of the switch should not be disabled + (DPSW_OPT_CTRL_IF_DIS not passed as a create time option). Without the + control interface, the driver is not capable to provide proper Rx/Tx traffic + support on the switch port netdevices. + :: + + fsl_dpaa2_switch dpsw.0: Control Interface is disabled, cannot probe + +Besides the configuration of the actual DPSW object, the dpaa2-switch driver +will need the following DPAA2 objects: + + * 1 DPMCP - A Management Command Portal object is needed for any interraction + with the MC firmware. + + * 1 DPBP - A Buffer Pool is used for seeding buffers intended for the Rx path + on the control interface. + + * Access to at least one DPIO object (Software Portal) is needed for any + enqueue/dequeue operation to be performed on the control interface queues. + The DPIO object will be shared, no need for a private one. + +Switching features +================== + +The driver supports the configuration of L2 forwarding rules in hardware for +port bridging as well as standalone usage of the independent switch interfaces. + +The hardware is not configurable with respect to VLAN awareness, thus any DPAA2 +switch port should be used only in usecases with a VLAN aware bridge:: + + $ ip link add dev br0 type bridge vlan_filtering 1 + + $ ip link add dev br1 type bridge + $ ip link set dev ethX master br1 + Error: fsl_dpaa2_switch: Cannot join a VLAN-unaware bridge + +Topology and loop detection through STP is supported when ``stp_state 1`` is +used at bridge create :: + + $ ip link add dev br0 type bridge vlan_filtering 1 stp_state 1 + +L2 FDB manipulation (add/delete/dump) is supported. + +HW FDB learning can be configured on each switch port independently through +bridge commands. When the HW learning is disabled, a fast age procedure will be +run and any previously learnt addresses will be removed. +:: + + $ bridge link set dev ethX learning off + $ bridge link set dev ethX learning on + +Restricting the unknown unicast and multicast flooding domain is supported, but +not independently of each other:: + + $ ip link set dev ethX type bridge_slave flood off mcast_flood off + $ ip link set dev ethX type bridge_slave flood off mcast_flood on + Error: fsl_dpaa2_switch: Cannot configure multicast flooding independently of unicast. + +Broadcast flooding on a switch port can be disabled/enabled through the brport sysfs:: + + $ echo 0 > /sys/bus/fsl-mc/devices/dpsw.Y/net/ethX/brport/broadcast_flood + +Offloads +======== + +Routing actions (redirect, trap, drop) +-------------------------------------- + +The DPAA2 switch is able to offload flow-based redirection of packets making +use of ACL tables. Shared filter blocks are supported by sharing a single ACL +table between multiple ports. + +The following flow keys are supported: + + * Ethernet: dst_mac/src_mac + * IPv4: dst_ip/src_ip/ip_proto/tos + * VLAN: vlan_id/vlan_prio/vlan_tpid/vlan_dei + * L4: dst_port/src_port + +Also, the matchall filter can be used to redirect the entire traffic received +on a port. + +As per flow actions, the following are supported: + + * drop + * mirred egress redirect + * trap + +Each ACL entry (filter) can be setup with only one of the listed +actions. + +Example 1: send frames received on eth4 with a SA of 00:01:02:03:04:05 to the +CPU:: + + $ tc qdisc add dev eth4 clsact + $ tc filter add dev eth4 ingress flower src_mac 00:01:02:03:04:05 skip_sw action trap + +Example 2: drop frames received on eth4 with VID 100 and PCP of 3:: + + $ tc filter add dev eth4 ingress protocol 802.1q flower skip_sw vlan_id 100 vlan_prio 3 action drop + +Example 3: redirect all frames received on eth4 to eth1:: + + $ tc filter add dev eth4 ingress matchall action mirred egress redirect dev eth1 + +Example 4: Use a single shared filter block on both eth5 and eth6:: + + $ tc qdisc add dev eth5 ingress_block 1 clsact + $ tc qdisc add dev eth6 ingress_block 1 clsact + $ tc filter add block 1 ingress flower dst_mac 00:01:02:03:04:04 skip_sw \ + action trap + $ tc filter add block 1 ingress protocol ipv4 flower src_ip 192.168.1.1 skip_sw \ + action mirred egress redirect dev eth3 + +Mirroring +~~~~~~~~~ + +The DPAA2 switch supports only per port mirroring and per VLAN mirroring. +Adding mirroring filters in shared blocks is also supported. + +When using the tc-flower classifier with the 802.1q protocol, only the +''vlan_id'' key will be accepted. Mirroring based on any other fields from the +802.1q protocol will be rejected:: + + $ tc qdisc add dev eth8 ingress_block 1 clsact + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_prio 3 action mirred egress mirror dev eth6 + Error: fsl_dpaa2_switch: Only matching on VLAN ID supported. + We have an error talking to the kernel + +If a mirroring VLAN filter is requested on a port, the VLAN must to be +installed on the switch port in question either using ''bridge'' or by creating +a VLAN upper device if the switch port is used as a standalone interface:: + + $ tc qdisc add dev eth8 ingress_block 1 clsact + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + Error: VLAN must be installed on the switch port. + We have an error talking to the kernel + + $ bridge vlan add vid 200 dev eth8 + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + + $ ip link add link eth8 name eth8.200 type vlan id 200 + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + +Also, it should be noted that the mirrored traffic will be subject to the same +egress restrictions as any other traffic. This means that when a mirrored +packet will reach the mirror port, if the VLAN found in the packet is not +installed on the port it will get dropped. + +The DPAA2 switch supports only a single mirroring destination, thus multiple +mirror rules can be installed but their ''to'' port has to be the same:: + + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 100 action mirred egress mirror dev eth7 + Error: fsl_dpaa2_switch: Multiple mirror ports not supported. + We have an error talking to the kernel diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5.rst index ef8cb62e82a1..4b59cf2c599f 100644 --- a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5.rst +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5.rst @@ -656,3 +656,47 @@ Bridge offloads tracepoints: $ cat /sys/kernel/debug/tracing/trace ... ip-5387 [000] ...1 573713: mlx5_esw_bridge_vport_cleanup: vport_num=1 + +Eswitch QoS tracepoints: + +- mlx5_esw_vport_qos_create: trace creation of transmit scheduler arbiter for vport:: + + $ echo mlx5:mlx5_esw_vport_qos_create >> /sys/kernel/debug/tracing/set_event + $ cat /sys/kernel/debug/tracing/trace + ... + <...>-23496 [018] .... 73136.838831: mlx5_esw_vport_qos_create: (0000:82:00.0) vport=2 tsar_ix=4 bw_share=0, max_rate=0 group=000000007b576bb3 + +- mlx5_esw_vport_qos_config: trace configuration of transmit scheduler arbiter for vport:: + + $ echo mlx5:mlx5_esw_vport_qos_config >> /sys/kernel/debug/tracing/set_event + $ cat /sys/kernel/debug/tracing/trace + ... + <...>-26548 [023] .... 75754.223823: mlx5_esw_vport_qos_config: (0000:82:00.0) vport=1 tsar_ix=3 bw_share=34, max_rate=10000 group=000000007b576bb3 + +- mlx5_esw_vport_qos_destroy: trace deletion of transmit scheduler arbiter for vport:: + + $ echo mlx5:mlx5_esw_vport_qos_destroy >> /sys/kernel/debug/tracing/set_event + $ cat /sys/kernel/debug/tracing/trace + ... + <...>-27418 [004] .... 76546.680901: mlx5_esw_vport_qos_destroy: (0000:82:00.0) vport=1 tsar_ix=3 + +- mlx5_esw_group_qos_create: trace creation of transmit scheduler arbiter for rate group:: + + $ echo mlx5:mlx5_esw_group_qos_create >> /sys/kernel/debug/tracing/set_event + $ cat /sys/kernel/debug/tracing/trace + ... + <...>-26578 [008] .... 75776.022112: mlx5_esw_group_qos_create: (0000:82:00.0) group=000000008dac63ea tsar_ix=5 + +- mlx5_esw_group_qos_config: trace configuration of transmit scheduler arbiter for rate group:: + + $ echo mlx5:mlx5_esw_group_qos_config >> /sys/kernel/debug/tracing/set_event + $ cat /sys/kernel/debug/tracing/trace + ... + <...>-27303 [020] .... 76461.455356: mlx5_esw_group_qos_config: (0000:82:00.0) group=000000008dac63ea tsar_ix=5 bw_share=100 max_rate=20000 + +- mlx5_esw_group_qos_destroy: trace deletion of transmit scheduler arbiter for group:: + + $ echo mlx5:mlx5_esw_group_qos_destroy >> /sys/kernel/debug/tracing/set_event + $ cat /sys/kernel/debug/tracing/trace + ... + <...>-27418 [006] .... 76547.187258: mlx5_esw_group_qos_destroy: (0000:82:00.0) group=000000007b576bb3 tsar_ix=1 diff --git a/Documentation/networking/devlink/devlink-params.rst b/Documentation/networking/devlink/devlink-params.rst index 54c9f107c4b0..4878907e9232 100644 --- a/Documentation/networking/devlink/devlink-params.rst +++ b/Documentation/networking/devlink/devlink-params.rst @@ -97,6 +97,18 @@ own name. * - ``enable_roce`` - Boolean - Enable handling of RoCE traffic in the device. + * - ``enable_eth`` + - Boolean + - When enabled, the device driver will instantiate Ethernet specific + auxiliary device of the devlink device. + * - ``enable_rdma`` + - Boolean + - When enabled, the device driver will instantiate RDMA specific + auxiliary device of the devlink device. + * - ``enable_vnet`` + - Boolean + - When enabled, the device driver will instantiate VDPA networking + specific auxiliary device of the devlink device. * - ``internal_err_reset`` - Boolean - When enabled, the device driver will reset the device on internal diff --git a/Documentation/networking/devlink/hns3.rst b/Documentation/networking/devlink/hns3.rst new file mode 100644 index 000000000000..4562a6e4782f --- /dev/null +++ b/Documentation/networking/devlink/hns3.rst @@ -0,0 +1,25 @@ +.. SPDX-License-Identifier: GPL-2.0 + +==================== +hns3 devlink support +==================== + +This document describes the devlink features implemented by the ``hns3`` +device driver. + +The ``hns3`` driver supports reloading via ``DEVLINK_CMD_RELOAD``. + +Info versions +============= + +The ``hns3`` driver reports the following versions + +.. list-table:: devlink info versions implemented + :widths: 10 10 80 + + * - Name + - Type + - Description + * - ``fw`` + - running + - Used to represent the firmware version. diff --git a/Documentation/networking/devlink/index.rst b/Documentation/networking/devlink/index.rst index b3b9e0692088..45b5f8b341df 100644 --- a/Documentation/networking/devlink/index.rst +++ b/Documentation/networking/devlink/index.rst @@ -34,6 +34,7 @@ parameters, info versions, and other features it supports. :maxdepth: 1 bnxt + hns3 ionic ice mlx4 @@ -42,7 +43,6 @@ parameters, info versions, and other features it supports. mv88e6xxx netdevsim nfp - sja1105 qed ti-cpsw-switch am65-nuss-cpsw-switch diff --git a/Documentation/networking/devlink/sja1105.rst b/Documentation/networking/devlink/sja1105.rst deleted file mode 100644 index e2679c274085..000000000000 --- a/Documentation/networking/devlink/sja1105.rst +++ /dev/null @@ -1,49 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -======================= -sja1105 devlink support -======================= - -This document describes the devlink features implemented -by the ``sja1105`` device driver. - -Parameters -========== - -.. list-table:: Driver-specific parameters implemented - :widths: 5 5 5 85 - - * - Name - - Type - - Mode - - Description - * - ``best_effort_vlan_filtering`` - - Boolean - - runtime - - Allow plain ETH_P_8021Q headers to be used as DSA tags. - - Benefits: - - - Can terminate untagged traffic over switch net - devices even when enslaved to a bridge with - vlan_filtering=1. - - Can terminate VLAN-tagged traffic over switch net - devices even when enslaved to a bridge with - vlan_filtering=1, with some constraints (no more than - 7 non-pvid VLANs per user port). - - Can do QoS based on VLAN PCP and VLAN membership - admission control for autonomously forwarded frames - (regardless of whether they can be terminated on the - CPU or not). - - Drawbacks: - - - User cannot use VLANs in range 1024-3071. If the - switch receives frames with such VIDs, it will - misinterpret them as DSA tags. - - Switch uses Shared VLAN Learning (FDB lookup uses - only DMAC as key). - - When VLANs span cross-chip topologies, the total - number of permitted VLANs may be less than 7 per - port, due to a maximum number of 32 VLAN retagging - rules per switch. diff --git a/Documentation/networking/dsa/dsa.rst b/Documentation/networking/dsa/dsa.rst index 20baacf2bc5c..89bb4fa4c362 100644 --- a/Documentation/networking/dsa/dsa.rst +++ b/Documentation/networking/dsa/dsa.rst @@ -200,19 +200,6 @@ receive all frames regardless of the value of the MAC DA. This can be done by setting the ``promisc_on_master`` property of the ``struct dsa_device_ops``. Note that this assumes a DSA-unaware master driver, which is the norm. -Hardware manufacturers are strongly discouraged to do this, but some tagging -protocols might not provide source port information on RX for all packets, but -e.g. only for control traffic (link-local PDUs). In this case, by implementing -the ``filter`` method of ``struct dsa_device_ops``, the tagger might select -which packets are to be redirected on RX towards the virtual DSA user network -interfaces, and which are to be left in the DSA master's RX data path. - -It might also happen (although silicon vendors are strongly discouraged to -produce hardware like this) that a tagging protocol splits the switch-specific -information into a header portion and a tail portion, therefore not falling -cleanly into any of the above 3 categories. DSA does not support this -configuration. - Master network devices ---------------------- @@ -663,6 +650,22 @@ Bridge layer CPU port, and flooding towards the CPU port should also be enabled, due to a lack of an explicit address filtering mechanism in the DSA core. +- ``port_bridge_tx_fwd_offload``: bridge layer function invoked after + ``port_bridge_join`` when a driver sets ``ds->num_fwd_offloading_bridges`` to + a non-zero value. Returning success in this function activates the TX + forwarding offload bridge feature for this port, which enables the tagging + protocol driver to inject data plane packets towards the bridging domain that + the port is a part of. Data plane packets are subject to FDB lookup, hardware + learning on the CPU port, and do not override the port STP state. + Additionally, replication of data plane packets (multicast, flooding) is + handled in hardware and the bridge driver will transmit a single skb for each + packet that needs replication. The method is provided as a configuration + point for drivers that need to configure the hardware for enabling this + feature. + +- ``port_bridge_tx_fwd_unoffload``: bridge layer function invoken when a driver + leaves a bridge port which had the TX forwarding offload feature enabled. + Bridge VLAN filtering --------------------- diff --git a/Documentation/networking/dsa/sja1105.rst b/Documentation/networking/dsa/sja1105.rst index da4057ba37f1..564caeebe2b2 100644 --- a/Documentation/networking/dsa/sja1105.rst +++ b/Documentation/networking/dsa/sja1105.rst @@ -65,199 +65,6 @@ If that changed setting can be transmitted to the switch through the dynamic reconfiguration interface, it is; otherwise the switch is reset and reprogrammed with the updated static configuration. -Traffic support -=============== - -The switches do not have hardware support for DSA tags, except for "slow -protocols" for switch control as STP and PTP. For these, the switches have two -programmable filters for link-local destination MACs. -These are used to trap BPDUs and PTP traffic to the master netdevice, and are -further used to support STP and 1588 ordinary clock/boundary clock -functionality. For frames trapped to the CPU, source port and switch ID -information is encoded by the hardware into the frames. - -But by leveraging ``CONFIG_NET_DSA_TAG_8021Q`` (a software-defined DSA tagging -format based on VLANs), general-purpose traffic termination through the network -stack can be supported under certain circumstances. - -Depending on VLAN awareness state, the following operating modes are possible -with the switch: - -- Mode 1 (VLAN-unaware): a port is in this mode when it is used as a standalone - net device, or when it is enslaved to a bridge with ``vlan_filtering=0``. -- Mode 2 (fully VLAN-aware): a port is in this mode when it is enslaved to a - bridge with ``vlan_filtering=1``. Access to the entire VLAN range is given to - the user through ``bridge vlan`` commands, but general-purpose (anything - other than STP, PTP etc) traffic termination is not possible through the - switch net devices. The other packets can be still by user space processed - through the DSA master interface (similar to ``DSA_TAG_PROTO_NONE``). -- Mode 3 (best-effort VLAN-aware): a port is in this mode when enslaved to a - bridge with ``vlan_filtering=1``, and the devlink property of its parent - switch named ``best_effort_vlan_filtering`` is set to ``true``. When - configured like this, the range of usable VIDs is reduced (0 to 1023 and 3072 - to 4094), so is the number of usable VIDs (maximum of 7 non-pvid VLANs per - port*), and shared VLAN learning is performed (FDB lookup is done only by - DMAC, not also by VID). - -To summarize, in each mode, the following types of traffic are supported over -the switch net devices: - -+-------------+-----------+--------------+------------+ -| | Mode 1 | Mode 2 | Mode 3 | -+=============+===========+==============+============+ -| Regular | Yes | No | Yes | -| traffic | | (use master) | | -+-------------+-----------+--------------+------------+ -| Management | Yes | Yes | Yes | -| traffic | | | | -| (BPDU, PTP) | | | | -+-------------+-----------+--------------+------------+ - -To configure the switch to operate in Mode 3, the following steps can be -followed:: - - ip link add dev br0 type bridge - # swp2 operates in Mode 1 now - ip link set dev swp2 master br0 - # swp2 temporarily moves to Mode 2 - ip link set dev br0 type bridge vlan_filtering 1 - [ 61.204770] sja1105 spi0.1: Reset switch and programmed static config. Reason: VLAN filtering - [ 61.239944] sja1105 spi0.1: Disabled switch tagging - # swp3 now operates in Mode 3 - devlink dev param set spi/spi0.1 name best_effort_vlan_filtering value true cmode runtime - [ 64.682927] sja1105 spi0.1: Reset switch and programmed static config. Reason: VLAN filtering - [ 64.711925] sja1105 spi0.1: Enabled switch tagging - # Cannot use VLANs in range 1024-3071 while in Mode 3. - bridge vlan add dev swp2 vid 1025 untagged pvid - RTNETLINK answers: Operation not permitted - bridge vlan add dev swp2 vid 100 - bridge vlan add dev swp2 vid 101 untagged - bridge vlan - port vlan ids - swp5 1 PVID Egress Untagged - - swp2 1 PVID Egress Untagged - 100 - 101 Egress Untagged - - swp3 1 PVID Egress Untagged - - swp4 1 PVID Egress Untagged - - br0 1 PVID Egress Untagged - bridge vlan add dev swp2 vid 102 - bridge vlan add dev swp2 vid 103 - bridge vlan add dev swp2 vid 104 - bridge vlan add dev swp2 vid 105 - bridge vlan add dev swp2 vid 106 - bridge vlan add dev swp2 vid 107 - # Cannot use mode than 7 VLANs per port while in Mode 3. - [ 3885.216832] sja1105 spi0.1: No more free subvlans - -\* "maximum of 7 non-pvid VLANs per port": Decoding VLAN-tagged packets on the -CPU in mode 3 is possible through VLAN retagging of packets that go from the -switch to the CPU. In cross-chip topologies, the port that goes to the CPU -might also go to other switches. In that case, those other switches will see -only a retagged packet (which only has meaning for the CPU). So if they are -interested in this VLAN, they need to apply retagging in the reverse direction, -to recover the original value from it. This consumes extra hardware resources -for this switch. There is a maximum of 32 entries in the Retagging Table of -each switch device. - -As an example, consider this cross-chip topology:: - - +-------------------------------------------------+ - | Host SoC | - | +-------------------------+ | - | | DSA master for embedded | | - | | switch (non-sja1105) | | - | +--------+-------------------------+--------+ | - | | embedded L2 switch | | - | | | | - | | +--------------+ +--------------+ | | - | | |DSA master for| |DSA master for| | | - | | | SJA1105 1 | | SJA1105 2 | | | - +--+---+--------------+-----+--------------+---+--+ - - +-----------------------+ +-----------------------+ - | SJA1105 switch 1 | | SJA1105 switch 2 | - +-----+-----+-----+-----+ +-----+-----+-----+-----+ - |sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| - +-----+-----+-----+-----+ +-----+-----+-----+-----+ - -To reach the CPU, SJA1105 switch 1 (spi/spi2.1) uses the same port as is uses -to reach SJA1105 switch 2 (spi/spi2.2), which would be port 4 (not drawn). -Similarly for SJA1105 switch 2. - -Also consider the following commands, that add VLAN 100 to every sja1105 user -port:: - - devlink dev param set spi/spi2.1 name best_effort_vlan_filtering value true cmode runtime - devlink dev param set spi/spi2.2 name best_effort_vlan_filtering value true cmode runtime - ip link add dev br0 type bridge - for port in sw1p0 sw1p1 sw1p2 sw1p3 \ - sw2p0 sw2p1 sw2p2 sw2p3; do - ip link set dev $port master br0 - done - ip link set dev br0 type bridge vlan_filtering 1 - for port in sw1p0 sw1p1 sw1p2 sw1p3 \ - sw2p0 sw2p1 sw2p2; do - bridge vlan add dev $port vid 100 - done - ip link add link br0 name br0.100 type vlan id 100 && ip link set dev br0.100 up - ip addr add 192.168.100.3/24 dev br0.100 - bridge vlan add dev br0 vid 100 self - - bridge vlan - port vlan ids - sw1p0 1 PVID Egress Untagged - 100 - - sw1p1 1 PVID Egress Untagged - 100 - - sw1p2 1 PVID Egress Untagged - 100 - - sw1p3 1 PVID Egress Untagged - 100 - - sw2p0 1 PVID Egress Untagged - 100 - - sw2p1 1 PVID Egress Untagged - 100 - - sw2p2 1 PVID Egress Untagged - 100 - - sw2p3 1 PVID Egress Untagged - - br0 1 PVID Egress Untagged - 100 - -SJA1105 switch 1 consumes 1 retagging entry for each VLAN on each user port -towards the CPU. It also consumes 1 retagging entry for each non-pvid VLAN that -it is also interested in, which is configured on any port of any neighbor -switch. - -In this case, SJA1105 switch 1 consumes a total of 11 retagging entries, as -follows: - -- 8 retagging entries for VLANs 1 and 100 installed on its user ports - (``sw1p0`` - ``sw1p3``) -- 3 retagging entries for VLAN 100 installed on the user ports of SJA1105 - switch 2 (``sw2p0`` - ``sw2p2``), because it also has ports that are - interested in it. The VLAN 1 is a pvid on SJA1105 switch 2 and does not need - reverse retagging. - -SJA1105 switch 2 also consumes 11 retagging entries, but organized as follows: - -- 7 retagging entries for the bridge VLANs on its user ports (``sw2p0`` - - ``sw2p3``). -- 4 retagging entries for VLAN 100 installed on the user ports of SJA1105 - switch 1 (``sw1p0`` - ``sw1p3``). - Switching features ================== @@ -282,33 +89,10 @@ untagged), and therefore this mode is also supported. Segregating the switch ports in multiple bridges is supported (e.g. 2 + 2), but all bridges should have the same level of VLAN awareness (either both have -``vlan_filtering`` 0, or both 1). Also an inevitable limitation of the fact -that VLAN awareness is global at the switch level is that once a bridge with -``vlan_filtering`` enslaves at least one switch port, the other un-bridged -ports are no longer available for standalone traffic termination. +``vlan_filtering`` 0, or both 1). Topology and loop detection through STP is supported. -L2 FDB manipulation (add/delete/dump) is currently possible for the first -generation devices. Aging time of FDB entries, as well as enabling fully static -management (no address learning and no flooding of unknown traffic) is not yet -configurable in the driver. - -A special comment about bridging with other netdevices (illustrated with an -example): - -A board has eth0, eth1, swp0@eth1, swp1@eth1, swp2@eth1, swp3@eth1. -The switch ports (swp0-3) are under br0. -It is desired that eth0 is turned into another switched port that communicates -with swp0-3. - -If br0 has vlan_filtering 0, then eth0 can simply be added to br0 with the -intended results. -If br0 has vlan_filtering 1, then a new br1 interface needs to be created that -enslaves eth0 and eth1 (the DSA master of the switch ports). This is because in -this mode, the switch ports beneath br0 are not capable of regular traffic, and -are only used as a conduit for switchdev operations. - Offloads ======== diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst index c86628e6a235..d9b55b7a1a4d 100644 --- a/Documentation/networking/ethtool-netlink.rst +++ b/Documentation/networking/ethtool-netlink.rst @@ -595,6 +595,14 @@ Link extended substates: that is not formally supported, which led to signal integrity issues + + ``ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST`` The external clock signal for + SerDes is too weak or + unavailable. + + ``ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS`` The received signal for + SerDes is too weak because + analog loss of signal. ================================================================= ============================= Cable issue substates: @@ -939,12 +947,25 @@ Kernel response contents: ``ETHTOOL_A_COALESCE_TX_USECS_HIGH`` u32 delay (us), high Tx ``ETHTOOL_A_COALESCE_TX_MAX_FRAMES_HIGH`` u32 max packets, high Tx ``ETHTOOL_A_COALESCE_RATE_SAMPLE_INTERVAL`` u32 rate sampling interval + ``ETHTOOL_A_COALESCE_USE_CQE_TX`` bool timer reset mode, Tx + ``ETHTOOL_A_COALESCE_USE_CQE_RX`` bool timer reset mode, Rx =========================================== ====== ======================= Attributes are only included in reply if their value is not zero or the corresponding bit in ``ethtool_ops::supported_coalesce_params`` is set (i.e. they are declared as supported by driver). +Timer reset mode (``ETHTOOL_A_COALESCE_USE_CQE_TX`` and +``ETHTOOL_A_COALESCE_USE_CQE_RX``) controls the interaction between packet +arrival and the various time based delay parameters. By default timers are +expected to limit the max delay between any packet arrival/departure and a +corresponding interrupt. In this mode timer should be started by packet +arrival (sometimes delivery of previous interrupt) and reset when interrupt +is delivered. +Setting the appropriate attribute to 1 will enable ``CQE`` mode, where +each packet event resets the timer. In this mode timer is used to force +the interrupt if queue goes idle, while busy queues depend on the packet +limit to trigger interrupts. COALESCE_SET ============ @@ -977,6 +998,8 @@ Request contents: ``ETHTOOL_A_COALESCE_TX_USECS_HIGH`` u32 delay (us), high Tx ``ETHTOOL_A_COALESCE_TX_MAX_FRAMES_HIGH`` u32 max packets, high Tx ``ETHTOOL_A_COALESCE_RATE_SAMPLE_INTERVAL`` u32 rate sampling interval + ``ETHTOOL_A_COALESCE_USE_CQE_TX`` bool timer reset mode, Tx + ``ETHTOOL_A_COALESCE_USE_CQE_RX`` bool timer reset mode, Rx =========================================== ====== ======================= Request is rejected if it attributes declared as unsupported by driver (i.e. diff --git a/Documentation/networking/filter.rst b/Documentation/networking/filter.rst index 3e2221f4abe4..ce2b8e8bb9ab 100644 --- a/Documentation/networking/filter.rst +++ b/Documentation/networking/filter.rst @@ -320,13 +320,6 @@ Examples for low-level BPF: ret #-1 drop: ret #0 -**(Accelerated) VLAN w/ id 10**:: - - ld vlan_tci - jneq #10, drop - ret #-1 - drop: ret #0 - **icmp random packet sampling, 1 in 4**:: ldh [12] @@ -358,6 +351,22 @@ Examples for low-level BPF: bad: ret #0 /* SECCOMP_RET_KILL_THREAD */ good: ret #0x7fff0000 /* SECCOMP_RET_ALLOW */ +Examples for low-level BPF extension: + +**Packet for interface index 13**:: + + ld ifidx + jneq #13, drop + ret #-1 + drop: ret #0 + +**(Accelerated) VLAN w/ id 10**:: + + ld vlan_tci + jneq #10, drop + ret #-1 + drop: ret #0 + The above example code can be placed into a file (here called "foo"), and then be passed to the bpf_asm tool for generating opcodes, output that xt_bpf and cls_bpf understands and can directly be loaded with. Example with above @@ -629,8 +638,8 @@ extension, PTP dissector/classifier, and much more. They are all internally converted by the kernel into the new instruction set representation and run in the eBPF interpreter. For in-kernel handlers, this all works transparently by using bpf_prog_create() for setting up the filter, resp. -bpf_prog_destroy() for destroying it. The macro -BPF_PROG_RUN(filter, ctx) transparently invokes eBPF interpreter or JITed +bpf_prog_destroy() for destroying it. The function +bpf_prog_run(filter, ctx) transparently invokes eBPF interpreter or JITed code to run the filter. 'filter' is a pointer to struct bpf_prog that we got from bpf_prog_create(), and 'ctx' the given context (e.g. skb pointer). All constraints and restrictions from bpf_check_classic() apply diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst index e9ce55992aa9..58bc8cd367c6 100644 --- a/Documentation/networking/index.rst +++ b/Documentation/networking/index.rst @@ -57,6 +57,7 @@ Contents: gen_stats gtp ila + ioam6-sysctl ipddp ip_dynaddr ipsec @@ -68,6 +69,7 @@ Contents: l2tp lapb-module mac80211-injection + mctp mpls-sysctl mptcp-sysctl multiqueue diff --git a/Documentation/networking/ioam6-sysctl.rst b/Documentation/networking/ioam6-sysctl.rst new file mode 100644 index 000000000000..c18cab2c481a --- /dev/null +++ b/Documentation/networking/ioam6-sysctl.rst @@ -0,0 +1,26 @@ +.. SPDX-License-Identifier: GPL-2.0 + +===================== +IOAM6 Sysfs variables +===================== + + +/proc/sys/net/conf/<iface>/ioam6_* variables: +============================================= + +ioam6_enabled - BOOL + Accept (= enabled) or ignore (= disabled) IPv6 IOAM options on ingress + for this interface. + + * 0 - disabled (default) + * 1 - enabled + +ioam6_id - SHORT INTEGER + Define the IOAM id of this interface. + + Default is ~0. + +ioam6_id_wide - INTEGER + Define the wide IOAM id of this interface. + + Default is ~0. diff --git a/Documentation/networking/ip-sysctl.rst b/Documentation/networking/ip-sysctl.rst index 316c7dfa9693..d91ab28718d4 100644 --- a/Documentation/networking/ip-sysctl.rst +++ b/Documentation/networking/ip-sysctl.rst @@ -1926,6 +1926,23 @@ fib_notify_on_flag_change - INTEGER - 1 - Emit notifications. - 2 - Emit notifications only for RTM_F_OFFLOAD_FAILED flag change. +ioam6_id - INTEGER + Define the IOAM id of this node. Uses only 24 bits out of 32 in total. + + Min: 0 + Max: 0xFFFFFF + + Default: 0xFFFFFF + +ioam6_id_wide - LONG INTEGER + Define the wide IOAM id of this node. Uses only 56 bits out of 64 in + total. Can be different from ioam6_id. + + Min: 0 + Max: 0xFFFFFFFFFFFFFF + + Default: 0xFFFFFFFFFFFFFF + IPv6 Fragmentation: ip6frag_high_thresh - INTEGER diff --git a/Documentation/networking/mctp.rst b/Documentation/networking/mctp.rst new file mode 100644 index 000000000000..6100cdc220f6 --- /dev/null +++ b/Documentation/networking/mctp.rst @@ -0,0 +1,213 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================== +Management Component Transport Protocol (MCTP) +============================================== + +net/mctp/ contains protocol support for MCTP, as defined by DMTF standard +DSP0236. Physical interface drivers ("bindings" in the specification) are +provided in drivers/net/mctp/. + +The core code provides a socket-based interface to send and receive MCTP +messages, through an AF_MCTP, SOCK_DGRAM socket. + +Structure: interfaces & networks +================================ + +The kernel models the local MCTP topology through two items: interfaces and +networks. + +An interface (or "link") is an instance of an MCTP physical transport binding +(as defined by DSP0236, section 3.2.47), likely connected to a specific hardware +device. This is represented as a ``struct netdevice``. + +A network defines a unique address space for MCTP endpoints by endpoint-ID +(described by DSP0236, section 3.2.31). A network has a user-visible identifier +to allow references from userspace. Route definitions are specific to one +network. + +Interfaces are associated with one network. A network may be associated with one +or more interfaces. + +If multiple networks are present, each may contain endpoint IDs (EIDs) that are +also present on other networks. + +Sockets API +=========== + +Protocol definitions +-------------------- + +MCTP uses ``AF_MCTP`` / ``PF_MCTP`` for the address- and protocol- families. +Since MCTP is message-based, only ``SOCK_DGRAM`` sockets are supported. + +.. code-block:: C + + int sd = socket(AF_MCTP, SOCK_DGRAM, 0); + +The only (current) value for the ``protocol`` argument is 0. + +As with all socket address families, source and destination addresses are +specified with a ``sockaddr`` type, with a single-byte endpoint address: + +.. code-block:: C + + typedef __u8 mctp_eid_t; + + struct mctp_addr { + mctp_eid_t s_addr; + }; + + struct sockaddr_mctp { + unsigned short int smctp_family; + int smctp_network; + struct mctp_addr smctp_addr; + __u8 smctp_type; + __u8 smctp_tag; + }; + + #define MCTP_NET_ANY 0x0 + #define MCTP_ADDR_ANY 0xff + + +Syscall behaviour +----------------- + +The following sections describe the MCTP-specific behaviours of the standard +socket system calls. These behaviours have been chosen to map closely to the +existing sockets APIs. + +``bind()`` : set local socket address +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Sockets that receive incoming request packets will bind to a local address, +using the ``bind()`` syscall. + +.. code-block:: C + + struct sockaddr_mctp addr; + + addr.smctp_family = AF_MCTP; + addr.smctp_network = MCTP_NET_ANY; + addr.smctp_addr.s_addr = MCTP_ADDR_ANY; + addr.smctp_type = MCTP_TYPE_PLDM; + addr.smctp_tag = MCTP_TAG_OWNER; + + int rc = bind(sd, (struct sockaddr *)&addr, sizeof(addr)); + +This establishes the local address of the socket. Incoming MCTP messages that +match the network, address, and message type will be received by this socket. +The reference to 'incoming' is important here; a bound socket will only receive +messages with the TO bit set, to indicate an incoming request message, rather +than a response. + +The ``smctp_tag`` value will configure the tags accepted from the remote side of +this socket. Given the above, the only valid value is ``MCTP_TAG_OWNER``, which +will result in remotely "owned" tags being routed to this socket. Since +``MCTP_TAG_OWNER`` is set, the 3 least-significant bits of ``smctp_tag`` are not +used; callers must set them to zero. + +A ``smctp_network`` value of ``MCTP_NET_ANY`` will configure the socket to +receive incoming packets from any locally-connected network. A specific network +value will cause the socket to only receive incoming messages from that network. + +The ``smctp_addr`` field specifies a local address to bind to. A value of +``MCTP_ADDR_ANY`` configures the socket to receive messages addressed to any +local destination EID. + +The ``smctp_type`` field specifies which message types to receive. Only the +lower 7 bits of the type is matched on incoming messages (ie., the +most-significant IC bit is not part of the match). This results in the socket +receiving packets with and without a message integrity check footer. + +``sendto()``, ``sendmsg()``, ``send()`` : transmit an MCTP message +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +An MCTP message is transmitted using one of the ``sendto()``, ``sendmsg()`` or +``send()`` syscalls. Using ``sendto()`` as the primary example: + +.. code-block:: C + + struct sockaddr_mctp addr; + char buf[14]; + ssize_t len; + + /* set message destination */ + addr.smctp_family = AF_MCTP; + addr.smctp_network = 0; + addr.smctp_addr.s_addr = 8; + addr.smctp_tag = MCTP_TAG_OWNER; + addr.smctp_type = MCTP_TYPE_ECHO; + + /* arbitrary message to send, with message-type header */ + buf[0] = MCTP_TYPE_ECHO; + memcpy(buf + 1, "hello, world!", sizeof(buf) - 1); + + len = sendto(sd, buf, sizeof(buf), 0, + (struct sockaddr_mctp *)&addr, sizeof(addr)); + +The network and address fields of ``addr`` define the remote address to send to. +If ``smctp_tag`` has the ``MCTP_TAG_OWNER``, the kernel will ignore any bits set +in ``MCTP_TAG_VALUE``, and generate a tag value suitable for the destination +EID. If ``MCTP_TAG_OWNER`` is not set, the message will be sent with the tag +value as specified. If a tag value cannot be allocated, the system call will +report an errno of ``EAGAIN``. + +The application must provide the message type byte as the first byte of the +message buffer passed to ``sendto()``. If a message integrity check is to be +included in the transmitted message, it must also be provided in the message +buffer, and the most-significant bit of the message type byte must be 1. + +The ``sendmsg()`` system call allows a more compact argument interface, and the +message buffer to be specified as a scatter-gather list. At present no ancillary +message types (used for the ``msg_control`` data passed to ``sendmsg()``) are +defined. + +Transmitting a message on an unconnected socket with ``MCTP_TAG_OWNER`` +specified will cause an allocation of a tag, if no valid tag is already +allocated for that destination. The (destination-eid,tag) tuple acts as an +implicit local socket address, to allow the socket to receive responses to this +outgoing message. If any previous allocation has been performed (to for a +different remote EID), that allocation is lost. + +Sockets will only receive responses to requests they have sent (with TO=1) and +may only respond (with TO=0) to requests they have received. + +``recvfrom()``, ``recvmsg()``, ``recv()`` : receive an MCTP message +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +An MCTP message can be received by an application using one of the +``recvfrom()``, ``recvmsg()``, or ``recv()`` system calls. Using ``recvfrom()`` +as the primary example: + +.. code-block:: C + + struct sockaddr_mctp addr; + socklen_t addrlen; + char buf[14]; + ssize_t len; + + addrlen = sizeof(addr); + + len = recvfrom(sd, buf, sizeof(buf), 0, + (struct sockaddr_mctp *)&addr, &addrlen); + + /* We can expect addr to describe an MCTP address */ + assert(addrlen >= sizeof(buf)); + assert(addr.smctp_family == AF_MCTP); + + printf("received %zd bytes from remote EID %d\n", rc, addr.smctp_addr); + +The address argument to ``recvfrom`` and ``recvmsg`` is populated with the +remote address of the incoming message, including tag value (this will be needed +in order to reply to the message). + +The first byte of the message buffer will contain the message type byte. If an +integrity check follows the message, it will be included in the received buffer. + +The ``recv()`` system call behaves in a similar way, but does not provide a +remote address to the application. Therefore, these are only useful if the +remote address is already known, or the message does not require a reply. + +Like the send calls, sockets will only receive responses to requests they have +sent (TO=1) and may only respond (TO=0) to requests they have received. diff --git a/Documentation/networking/mptcp-sysctl.rst b/Documentation/networking/mptcp-sysctl.rst index 76d939e688b8..b0d4da71e68e 100644 --- a/Documentation/networking/mptcp-sysctl.rst +++ b/Documentation/networking/mptcp-sysctl.rst @@ -45,3 +45,15 @@ allow_join_initial_addr_port - BOOLEAN This is a per-namespace sysctl. Default: 1 + +stale_loss_cnt - INTEGER + The number of MPTCP-level retransmission intervals with no traffic and + pending outstanding data on a given subflow required to declare it stale. + The packet scheduler ignores stale subflows. + A low stale_loss_cnt value allows for fast active-backup switch-over, + an high value maximize links utilization on edge scenarios e.g. lossy + link with high BER or peer pausing the data processing. + + This is a per-namespace sysctl. + + Default: 4 diff --git a/Documentation/networking/netdevices.rst b/Documentation/networking/netdevices.rst index 17bdcb746dcf..9e4cccb90b87 100644 --- a/Documentation/networking/netdevices.rst +++ b/Documentation/networking/netdevices.rst @@ -222,6 +222,35 @@ ndo_do_ioctl: Synchronization: rtnl_lock() semaphore. Context: process + This is only called by network subsystems internally, + not by user space calling ioctl as it was in before + linux-5.14. + +ndo_siocbond: + Synchronization: rtnl_lock() semaphore. + Context: process + + Used by the bonding driver for the SIOCBOND family of + ioctl commands. + +ndo_siocwandev: + Synchronization: rtnl_lock() semaphore. + Context: process + + Used by the drivers/net/wan framework to handle + the SIOCWANDEV ioctl with the if_settings structure. + +ndo_siocdevprivate: + Synchronization: rtnl_lock() semaphore. + Context: process + + This is used to implement SIOCDEVPRIVATE ioctl helpers. + These should not be added to new drivers, so don't use. + +ndo_eth_ioctl: + Synchronization: rtnl_lock() semaphore. + Context: process + ndo_get_stats: Synchronization: rtnl_lock() semaphore, dev_base_lock rwlock, or RCU. Context: atomic (can't sleep under rwlock or RCU) diff --git a/Documentation/networking/nf_conntrack-sysctl.rst b/Documentation/networking/nf_conntrack-sysctl.rst index 024d784157c8..34ca762ea56f 100644 --- a/Documentation/networking/nf_conntrack-sysctl.rst +++ b/Documentation/networking/nf_conntrack-sysctl.rst @@ -184,6 +184,13 @@ nf_conntrack_gre_timeout_stream - INTEGER (seconds) This extended timeout will be used in case there is an GRE stream detected. +nf_hooks_lwtunnel - BOOLEAN + - 0 - disabled (default) + - not 0 - enabled + + If this option is enabled, the lightweight tunnel netfilter hooks are + enabled. This option cannot be disabled once it is enabled. + nf_flowtable_tcp_timeout - INTEGER (seconds) default 30 diff --git a/Documentation/networking/pktgen.rst b/Documentation/networking/pktgen.rst index 7afa1c9f1183..1225f0f63ff0 100644 --- a/Documentation/networking/pktgen.rst +++ b/Documentation/networking/pktgen.rst @@ -248,26 +248,24 @@ Usage::: -i : ($DEV) output interface/device (required) -s : ($PKT_SIZE) packet size - -d : ($DEST_IP) destination IP + -d : ($DEST_IP) destination IP. CIDR (e.g. 198.18.0.0/15) is also allowed -m : ($DST_MAC) destination MAC-addr + -p : ($DST_PORT) destination PORT range (e.g. 433-444) is also allowed -t : ($THREADS) threads to start + -f : ($F_THREAD) index of first thread (zero indexed CPU number) -c : ($SKB_CLONE) SKB clones send before alloc new SKB + -n : ($COUNT) num messages to send per thread, 0 means indefinitely -b : ($BURST) HW level bursting of SKBs -v : ($VERBOSE) verbose -x : ($DEBUG) debug + -6 : ($IP6) IPv6 + -w : ($DELAY) Tx Delay value (ns) + -a : ($APPEND) Script will not reset generator's state, but will append its config The global variables being set are also listed. E.g. the required interface/device parameter "-i" sets variable $DEV. Copy the pktgen_sampleXX scripts and modify them to fit your own needs. -The old scripts:: - - pktgen.conf-1-2 # 1 CPU 2 dev - pktgen.conf-1-1-rdos # 1 CPU 1 dev w. route DoS - pktgen.conf-1-1-ip6 # 1 CPU 1 dev ipv6 - pktgen.conf-1-1-ip6-rdos # 1 CPU 1 dev ipv6 w. route DoS - pktgen.conf-1-1-flows # 1 CPU 1 dev multiple flows. - Interrupt affinity =================== @@ -398,7 +396,7 @@ Current commands and configuration options References: - ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/ -- tp://robur.slu.se/pub/Linux/net-development/pktgen-testing/examples/ +- ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/examples/ Paper from Linux-Kongress in Erlangen 2004. - ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/pktgen_paper.pdf diff --git a/Documentation/networking/timestamping.rst b/Documentation/networking/timestamping.rst index 7db3985359bc..a722eb30e014 100644 --- a/Documentation/networking/timestamping.rst +++ b/Documentation/networking/timestamping.rst @@ -625,7 +625,7 @@ interfaces of a DSA switch to share the same PHC. By design, PTP timestamping with a DSA switch does not need any special handling in the driver for the host port it is attached to. However, when the host port also supports PTP timestamping, DSA will take care of intercepting -the ``.ndo_do_ioctl`` calls towards the host port, and block attempts to enable +the ``.ndo_eth_ioctl`` calls towards the host port, and block attempts to enable hardware timestamping on it. This is because the SO_TIMESTAMPING API does not allow the delivery of multiple hardware timestamps for the same packet, so anybody else except for the DSA switch port must be prevented from doing so. @@ -688,7 +688,7 @@ ethtool ioctl operations for them need to be mediated by their respective MAC driver. Therefore, as opposed to DSA switches, modifications need to be done to each individual MAC driver for PHY timestamping support. This entails: -- Checking, in ``.ndo_do_ioctl``, whether ``phy_has_hwtstamp(netdev->phydev)`` +- Checking, in ``.ndo_eth_ioctl``, whether ``phy_has_hwtstamp(netdev->phydev)`` is true or not. If it is, then the MAC driver should not process this request but instead pass it on to the PHY using ``phy_mii_ioctl()``. @@ -747,7 +747,7 @@ For example, a typical driver design for TX timestamping might be to split the transmission part into 2 portions: 1. "TX": checks whether PTP timestamping has been previously enabled through - the ``.ndo_do_ioctl`` ("``priv->hwtstamp_tx_enabled == true``") and the + the ``.ndo_eth_ioctl`` ("``priv->hwtstamp_tx_enabled == true``") and the current skb requires a TX timestamp ("``skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP``"). If this is true, it sets the "``skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS``" flag. Note: as diff --git a/Documentation/networking/vrf.rst b/Documentation/networking/vrf.rst index 0dde145043bc..0a9a6f968cb9 100644 --- a/Documentation/networking/vrf.rst +++ b/Documentation/networking/vrf.rst @@ -144,6 +144,19 @@ default VRF are only handled by a socket not bound to any VRF:: netfilter rules on the VRF device can be used to limit access to services running in the default VRF context as well. +Using VRF-aware applications (applications which simultaneously create sockets +outside and inside VRFs) in conjunction with ``net.ipv4.tcp_l3mdev_accept=1`` +is possible but may lead to problems in some situations. With that sysctl +value, it is unspecified which listening socket will be selected to handle +connections for VRF traffic; ie. either a socket bound to the VRF or an unbound +socket may be used to accept new connections from a VRF. This somewhat +unexpected behavior can lead to problems if sockets are configured with extra +options (ex. TCP MD5 keys) with the expectation that VRF traffic will +exclusively be handled by sockets bound to VRFs, as would be the case with +``net.ipv4.tcp_l3mdev_accept=0``. Finally and as a reminder, regardless of +which listening socket is selected, established sockets will be created in the +VRF based on the ingress interface, as documented earlier. + -------------------------------------------------------------------------------- Using iproute2 for VRFs |