i2c: gpio: fault-injector: add 'inject_panic' injector

Add a fault injector simulating a Kernel panic happening after starting
a transfer. Read the docs for its usage.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

2 files changed, 56 insertions, 1 deletions

diff --git a/Documentation/i2c/gpio-fault-injection b/Documentation/i2c/gpio-fault-injection
index 1f1bb96a64bd..c87f416d53dd 100644
--- a/Documentation/i2c/gpio-fault-injection
+++ b/Documentation/i2c/gpio-fault-injection
@@ -108,3 +108,29 @@ idle bus is:
 
 # echo 200 > lose_arbitration &
 # i2cget -y <bus_to_test> 0x3f
+
+Panic during transfer
+=====================
+
+This fault injector will create a Kernel panic once the master under test
+started a transfer. This usually means that the state machine of the bus master
+driver will be ungracefully interrupted and the bus may end up in an unusual
+state. Use this to check if your shutdown/reboot/boot code can handle this
+scenario.
+
+"inject_panic"
+--------------
+
+This file is write only and you need to write the delay between the detected
+start of a transmission and the induced Kernel panic (in µs, maximum is 100ms).
+The calling process will then sleep and wait for the next bus clock. The
+process is interruptible, though.
+
+Start of a transfer is detected by waiting for SCL going down by the master
+under test.  A good starting point for using this fault injector is:
+
+# echo 0 > inject_panic &
+# i2cget -y <bus_to_test> <some_address>
+
+Note that there doesn't need to be a device listening to the address you are
+using. Results may vary depending on that, though.
diff --git a/drivers/i2c/busses/i2c-gpio.c b/drivers/i2c/busses/i2c-gpio.c
index 76e43783f50f..bba5c4627de3 100644
--- a/drivers/i2c/busses/i2c-gpio.c
+++ b/drivers/i2c/busses/i2c-gpio.c
@@ -231,6 +231,32 @@ static int fops_lose_arbitration_set(void *data, u64 duration)
 }
 DEFINE_DEBUGFS_ATTRIBUTE(fops_lose_arbitration, NULL, fops_lose_arbitration_set, "%llu\n");
 
+static irqreturn_t inject_panic_irq(int irq, void *dev_id)
+{
+	struct i2c_gpio_private_data *priv = dev_id;
+
+	udelay(priv->scl_irq_data);
+	panic("I2C fault injector induced panic");
+
+	return IRQ_HANDLED;
+}
+
+static int fops_inject_panic_set(void *data, u64 duration)
+{
+	struct i2c_gpio_private_data *priv = data;
+
+	if (duration > 100 * 1000)
+		return -EINVAL;
+
+	priv->scl_irq_data = duration;
+	/*
+	 * Interrupt on falling SCL. This ensures that the master under test has
+	 * really started the transfer.
+	 */
+	return i2c_gpio_fi_act_on_scl_irq(priv, inject_panic_irq);
+}
+DEFINE_DEBUGFS_ATTRIBUTE(fops_inject_panic, NULL, fops_inject_panic_set, "%llu\n");
+
 static void i2c_gpio_fault_injector_init(struct platform_device *pdev)
 {
 	struct i2c_gpio_private_data *priv = platform_get_drvdata(pdev);
@@ -256,9 +282,12 @@ static void i2c_gpio_fault_injector_init(struct platform_device *pdev)
 				   priv, &fops_incomplete_addr_phase);
 	debugfs_create_file_unsafe("incomplete_write_byte", 0200, priv->debug_dir,
 				   priv, &fops_incomplete_write_byte);
-	if (priv->bit_data.getscl)
+	if (priv->bit_data.getscl) {
+		debugfs_create_file_unsafe("inject_panic", 0200, priv->debug_dir,
+					   priv, &fops_inject_panic);
 		debugfs_create_file_unsafe("lose_arbitration", 0200, priv->debug_dir,
 					   priv, &fops_lose_arbitration);
+	}
 	debugfs_create_file_unsafe("scl", 0600, priv->debug_dir, priv, &fops_scl);
 	debugfs_create_file_unsafe("sda", 0600, priv->debug_dir, priv, &fops_sda);
 }