ARM: dts: qcom: Remove Arrow SD600 eval board

This patch removes support for the APQ8064 based Arrow SD600 eval
board.  This board was never sold publicly and had very limited
distribution.  As such, we are removing this board and no longer
going to support it.

Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>

3 files changed, 0 insertions, 469 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d625b9..00d6e65c28f5 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
 	ox820-cloudengines-pogoplug-series-3.dtb
 dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-apq8060-dragonboard.dtb \
-	qcom-apq8064-arrow-sd-600eval.dtb \
 	qcom-apq8064-cm-qs600.dtb \
 	qcom-apq8064-ifc6410.dtb \
 	qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
deleted file mode 100644
index 8df73156b73a..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
+++ /dev/null
@@ -1,53 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-&tlmm_pinmux {
-	card_detect: card-detect {
-		mux {
-			pins = "gpio26";
-			function = "gpio";
-			bias-disable;
-		};
-	};
-
-	pcie_pins: pcie-pinmux {
-		mux {
-			pins = "gpio27";
-			function = "gpio";
-		};
-		conf {
-			pins = "gpio27";
-			drive-strength = <12>;
-			bias-disable;
-		};
-	};
-
-	user_leds: user-leds {
-		mux {
-			pins = "gpio3", "gpio7", "gpio10", "gpio11";
-			function = "gpio";
-		};
-
-		conf {
-			pins = "gpio3", "gpio7", "gpio10", "gpio11";
-			function = "gpio";
-			output-low;
-		};
-	};
-
-	magneto_pins: magneto-pins {
-		mux {
-			pins = "gpio31", "gpio48";
-			function = "gpio";
-			bias-disable;
-		};
-	};
-};
-
-&pm8921_mpps {
-	mpp_leds: mpp-leds {
-		pinconf {
-			pins = "mpp7", "mpp8";
-			function = "digital";
-			output-low;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
deleted file mode 100644
index 76b56eafaab9..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ /dev/null
@@ -1,415 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-
-/ {
-	model = "Arrow Electronics, APQ8064 SD_600eval";
-	compatible = "arrow,sd_600eval", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-		serial1 = &gsbi1_serial;
-		i2c0 = &gsbi2_i2c;
-		i2c1 = &gsbi3_i2c;
-		i2c2 = &gsbi4_i2c;
-		i2c3 = &gsbi7_i2c;
-		spi0 = &gsbi5_spi;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		vph: regulator-fixed@1 {
-			compatible = "regulator-fixed";
-			regulator-min-microvolt = <4500000>;
-			regulator-max-microvolt = <4500000>;
-			regulator-name = "VPH";
-			regulator-type = "voltage";
-			regulator-boot-on;
-		};
-
-		/* on board fixed 3.3v supply */
-		vcc3v3: vcc3v3 {
-			compatible = "regulator-fixed";
-			regulator-name = "VCC3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con: endpoint {
-				remote-endpoint = <&hdmi_out>;
-			};
-		};
-	};
-
-	soc {
-		rpm@108000 {
-			regulators {
-				vdd_s1-supply = <&vph>;
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				vdd_s5-supply = <&vph>;
-				vdd_s6-supply = <&vph>;
-				vdd_s7-supply = <&vph>;
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l3_l15_l17-supply = <&vph>;
-				vdd_l4_l14-supply = <&vph>;
-				vdd_l5_l8_l16-supply = <&vph>;
-				vdd_l6_l7-supply = <&vph>;
-				vdd_l9_l11-supply = <&vph>;
-				vdd_l10_l22-supply = <&vph>;
-				vdd_l21_l23_l29-supply = <&vph>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				 };
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				/**
-				 * 1.8v required on LS expansion
-				 * for mezzanine boards
-				 */
-				l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-
-				lvs7 {
-					bias-pull-down;
-				};
-			};
-		};
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_UART_W_FC>;
-			serial@12450000 {
-				label = "LS-UART1";
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi1_uart_4pins>;
-			};
-		};
-
-		gsbi@12480000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@124a0000 {
-				/* On Low speed expansion and Sensors */
-				label = "LS-I2C0";
-				status = "okay";
-				lis3mdl_mag@1e {
-					compatible = "st,lis3mdl-magn";
-					reg = <0x1e>;
-					vdd-supply = <&vcc3v3>;
-					vddio-supply = <&pm8921_s4>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&magneto_pins>;
-					interrupt-parent = <&tlmm_pinmux>;
-
-					st,drdy-int-pin = <2>;
-					interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
-						     <31 IRQ_TYPE_EDGE_RISING>; /* INT */
-				};
-			};
-		};
-
-		gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-			/* On Low speed expansion */
-				status = "okay";
-				label = "LS-I2C1";
-				clock-frequency = <200000>;
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <64>;
-				};
-			};
-		};
-
-		gsbi@16300000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16380000 {
-				/* On High speed expansion */
-				label = "HS-CAM-I2C3";
-				status = "okay";
-			};
-		};
-
-		gsbi@1a200000 {
-			status = "okay";
-			spi@1a280000 {
-				/* On Low speed expansion */
-				label = "LS-SPI0";
-				status = "okay";
-			};
-		};
-
-		/* DEBUG UART  */
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				label = "LS-UART0";
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
-
-			i2c@16680000 {
-				/* On High speed expansion */
-				status = "okay";
-				label = "HS-CAM-I2C2";
-			};
-		};
-
-		leds {
-			pinctrl-names = "default";
-			pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
-			compatible = "gpio-leds";
-
-			user-led0 {
-				label = "user0-led";
-				gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "heartbeat";
-				default-state = "off";
-			};
-
-			user-led1 {
-				label = "user1-led";
-				gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "mmc0";
-				default-state = "off";
-			};
-
-			user-led2 {
-				label = "user2-led";
-				gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "mmc1";
-				default-state = "off";
-			};
-
-			user-led3 {
-				label = "user3-led";
-				gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "none";
-				default-state = "off";
-			};
-
-			wifi-led {
-				label = "WiFi-led";
-				gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-
-			bt-led {
-				label = "BT-led";
-				gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-		};
-
-		pci@1b500000 {
-			status = "okay";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&vcc3v3>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
-		};
-
-		phy@1b400000 {
-			status = "okay";
-		};
-
-		sata@29000000 {
-			status	= "okay";
-			target-supply	= <&pm8921_lvs7>;
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "peripheral";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc@12180000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l6>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
-			};
-		};
-
-		riva-pil@3204000 {
-			status = "okay";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
-		};
-
-		hdmi-tx@4a00000 {
-			status = "okay";
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-			hdmi-mux-supply = <&vcc3v3>;
-
-			hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
-
-			ports {
-				port@1 {
-					endpoint {
-						remote-endpoint = <&hdmi_con>;
-					};
-				};
-			};
-		};
-
-		hdmi-phy@4a00400 {
-			status = "okay";
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-		};
-
-		mdp@5100000 {
-			status = "okay";
-
-			ports {
-				port@3 {
-					endpoint {
-						remote-endpoint = <&hdmi_in>;
-					};
-				};
-			};
-		};
-	};
-};