blob: 48e63ab7848c0ba8da7671cfd75147fc11f6bfe1 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2711.dtsi"
#include "bcm2711-rpi.dtsi"
#include "bcm283x-rpi-wifi-bt.dtsi"
/ {
compatible = "raspberrypi,4-compute-module", "brcm,bcm2711";
chosen {
/* 8250 auxiliary UART instead of pl011 */
stdout-path = "serial1:115200n8";
};
sd_io_1v8_reg: regulator-sd-io-1v8 {
compatible = "regulator-gpio";
regulator-name = "vdd-sd-io";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
regulator-settling-time-us = <5000>;
gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
states = <1800000 0x1>,
<3300000 0x0>;
status = "okay";
};
sd_vcc_reg: regulator-sd-vcc {
compatible = "regulator-fixed";
regulator-name = "vcc-sd";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
enable-active-high;
gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
};
};
&bt {
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
};
/* EMMC2 is used to drive the eMMC */
&emmc2 {
bus-width = <8>;
vqmmc-supply = <&sd_io_1v8_reg>;
vmmc-supply = <&sd_vcc_reg>;
broken-cd;
/* Even the IP block is limited to 100 MHz
* this provides a throughput gain
*/
mmc-hs200-1_8v;
status = "okay";
};
&expgpio {
gpio-line-names = "BT_ON",
"WL_ON",
"PWR_LED_OFF",
"ANT1",
"VDD_SD_IO_SEL",
"CAM_GPIO",
"SD_PWR_ON",
"ANT2";
ant1: ant1-hog {
gpio-hog;
gpios = <3 GPIO_ACTIVE_HIGH>;
/* internal antenna enabled */
output-high;
line-name = "ant1";
};
ant2: ant2-hog {
gpio-hog;
gpios = <7 GPIO_ACTIVE_HIGH>;
/* external antenna disabled */
output-low;
line-name = "ant2";
};
};
&genet {
phy-handle = <&phy1>;
phy-mode = "rgmii-rxid";
status = "okay";
};
&genet_mdio {
phy1: ethernet-phy@0 {
/* No PHY interrupt */
reg = <0x0>;
};
};
/* uart0 communicates with the BT module */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
uart-has-rtscts;
};
/* uart1 is mapped to the pin header */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_gpio14>;
status = "okay";
};
&wifi_pwrseq {
reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
};
|
