1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
|
Qualcomm PMIC GPIO block
This binding describes the GPIO block(s) found in the 8xxx series of
PMIC's from Qualcomm.
- compatible:
Usage: required
Value type: <string>
Definition: must be one of:
"qcom,pm8005-gpio"
"qcom,pm8018-gpio"
"qcom,pm8038-gpio"
"qcom,pm8058-gpio"
"qcom,pm8916-gpio"
"qcom,pm8917-gpio"
"qcom,pm8921-gpio"
"qcom,pm8941-gpio"
"qcom,pm8994-gpio"
"qcom,pm8998-gpio"
"qcom,pma8084-gpio"
"qcom,pmi8994-gpio"
"qcom,pmi8998-gpio"
"qcom,pms405-gpio"
"qcom,pm8150-gpio"
And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio"
if the device is on an spmi bus or an ssbi bus respectively
- reg:
Usage: required
Value type: <prop-encoded-array>
Definition: Register base of the GPIO block and length.
- interrupts:
Usage: required
Value type: <prop-encoded-array>
Definition: Must contain an array of encoded interrupt specifiers for
each available GPIO
- gpio-controller:
Usage: required
Value type: <none>
Definition: Mark the device node as a GPIO controller
- #gpio-cells:
Usage: required
Value type: <u32>
Definition: Must be 2;
the first cell will be used to define gpio number and the
second denotes the flags for this gpio
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".
The pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin or a list of pins. This configuration can include the
mux function to select on those pin(s), and various pin configuration
parameters, as listed below.
SUBNODES:
The name of each subnode is not important; all subnodes should be enumerated
and processed purely based on their content.
Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.
The following generic properties as defined in pinctrl-bindings.txt are valid
to specify in a pin configuration subnode:
- pins:
Usage: required
Value type: <string-array>
Definition: List of gpio pins affected by the properties specified in
this subnode. Valid pins are:
gpio1-gpio4 for pm8005
gpio1-gpio6 for pm8018
gpio1-gpio12 for pm8038
gpio1-gpio40 for pm8058
gpio1-gpio4 for pm8916
gpio1-gpio38 for pm8917
gpio1-gpio44 for pm8921
gpio1-gpio36 for pm8941
gpio1-gpio22 for pm8994
gpio1-gpio26 for pm8998
gpio1-gpio22 for pma8084
gpio1-gpio10 for pmi8994
gpio1-gpio12 for pms405 (holes on gpio1, gpio9 and gpio10)
gpio1-gpio10 for pm8150 (holes on gpio2, gpio5, gpio7
and gpio8)
- function:
Usage: required
Value type: <string>
Definition: Specify the alternative function to be configured for the
specified pins. Valid values are:
"normal",
"paired",
"func1",
"func2",
"dtest1",
"dtest2",
"dtest3",
"dtest4",
And following values are supported by LV/MV GPIO subtypes:
"func3",
"func4"
- bias-disable:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as no pull.
- bias-pull-down:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as pull down.
- bias-pull-up:
Usage: optional
Value type: <empty>
Definition: The specified pins should be configured as pull up.
- qcom,pull-up-strength:
Usage: optional
Value type: <u32>
Definition: Specifies the strength to use for pull up, if selected.
Valid values are; as defined in
<dt-bindings/pinctrl/qcom,pmic-gpio.h>:
1: 30uA (PMIC_GPIO_PULL_UP_30)
2: 1.5uA (PMIC_GPIO_PULL_UP_1P5)
3: 31.5uA (PMIC_GPIO_PULL_UP_31P5)
4: 1.5uA + 30uA boost (PMIC_GPIO_PULL_UP_1P5_30)
If this property is omitted 30uA strength will be used if
pull up is selected
- bias-high-impedance:
Usage: optional
Value type: <none>
Definition: The specified pins will put in high-Z mode and disabled.
- input-enable:
Usage: optional
Value type: <none>
Definition: The specified pins are put in input mode.
- output-high:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
high.
- output-low:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
low.
- power-source:
Usage: optional
Value type: <u32>
Definition: Selects the power source for the specified pins. Valid
power sources are defined per chip in
<dt-bindings/pinctrl/qcom,pmic-gpio.h>
- qcom,drive-strength:
Usage: optional
Value type: <u32>
Definition: Selects the drive strength for the specified pins. Value
drive strengths are:
0: no (PMIC_GPIO_STRENGTH_NO)
1: high (PMIC_GPIO_STRENGTH_HIGH) 0.9mA @ 1.8V - 1.9mA @ 2.6V
2: medium (PMIC_GPIO_STRENGTH_MED) 0.6mA @ 1.8V - 1.25mA @ 2.6V
3: low (PMIC_GPIO_STRENGTH_LOW) 0.15mA @ 1.8V - 0.3mA @ 2.6V
as defined in <dt-bindings/pinctrl/qcom,pmic-gpio.h>
- drive-push-pull:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in push-pull mode.
- drive-open-drain:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in open-drain mode.
- drive-open-source:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in open-source mode.
- qcom,analog-pass:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in analog-pass-through mode.
- qcom,atest:
Usage: optional
Value type: <u32>
Definition: Selects ATEST rail to route to GPIO when it's configured
in analog-pass-through mode.
Valid values are 1-4 corresponding to ATEST1 to ATEST4.
- qcom,dtest-buffer:
Usage: optional
Value type: <u32>
Definition: Selects DTEST rail to route to GPIO when it's configured
as digital input.
Valid values are 1-4 corresponding to DTEST1 to DTEST4.
Example:
pm8921_gpio: gpio@150 {
compatible = "qcom,pm8921-gpio", "qcom,ssbi-gpio";
reg = <0x150 0x160>;
interrupts = <192 1>, <193 1>, <194 1>,
<195 1>, <196 1>, <197 1>,
<198 1>, <199 1>, <200 1>,
<201 1>, <202 1>, <203 1>,
<204 1>, <205 1>, <206 1>,
<207 1>, <208 1>, <209 1>,
<210 1>, <211 1>, <212 1>,
<213 1>, <214 1>, <215 1>,
<216 1>, <217 1>, <218 1>,
<219 1>, <220 1>, <221 1>,
<222 1>, <223 1>, <224 1>,
<225 1>, <226 1>, <227 1>,
<228 1>, <229 1>, <230 1>,
<231 1>, <232 1>, <233 1>,
<234 1>, <235 1>;
gpio-controller;
#gpio-cells = <2>;
pm8921_gpio_keys: gpio-keys {
volume-keys {
pins = "gpio20", "gpio21";
function = "normal";
input-enable;
bias-pull-up;
drive-push-pull;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8921_GPIO_S4>;
};
};
};
|
