1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/media/xilinx/xlnx,csi2rxss.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Xilinx MIPI CSI-2 Receiver Subsystem
maintainers:
- Vishal Sagar <vishal.sagar@xilinx.com>
description: |
The Xilinx MIPI CSI-2 Receiver Subsystem is used to capture MIPI CSI-2
traffic from compliant camera sensors and send the output as AXI4 Stream
video data for image processing.
The subsystem consists of a MIPI D-PHY in slave mode which captures the
data packets. This is passed along the MIPI CSI-2 Rx IP which extracts the
packet data. The optional Video Format Bridge (VFB) converts this data to
AXI4 Stream video data.
For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem.
Please note that this bindings includes only the MIPI CSI-2 Rx controller
and Video Format Bridge and not D-PHY.
properties:
compatible:
items:
- enum:
- xlnx,mipi-csi2-rx-subsystem-5.0
reg:
maxItems: 1
interrupts:
maxItems: 1
clocks:
description: List of clock specifiers
items:
- description: AXI Lite clock
- description: Video clock
clock-names:
items:
- const: lite_aclk
- const: video_aclk
xlnx,csi-pxl-format:
description: |
This denotes the CSI Data type selected in hw design.
Packets other than this data type (except for RAW8 and
User defined data types) will be filtered out.
Possible values are as below -
0x1e - YUV4228B
0x1f - YUV42210B
0x20 - RGB444
0x21 - RGB555
0x22 - RGB565
0x23 - RGB666
0x24 - RGB888
0x28 - RAW6
0x29 - RAW7
0x2a - RAW8
0x2b - RAW10
0x2c - RAW12
0x2d - RAW14
0x2e - RAW16
0x2f - RAW20
$ref: /schemas/types.yaml#/definitions/uint32
oneOf:
- minimum: 0x1e
maximum: 0x24
- minimum: 0x28
maximum: 0x2f
xlnx,vfb:
type: boolean
description: Present when Video Format Bridge is enabled in IP configuration
xlnx,en-csi-v2-0:
type: boolean
description: Present if CSI v2 is enabled in IP configuration.
xlnx,en-vcx:
type: boolean
description: |
When present, there are maximum 16 virtual channels, else only 4.
xlnx,en-active-lanes:
type: boolean
description: |
Present if the number of active lanes can be re-configured at
runtime in the Protocol Configuration Register. Otherwise all lanes,
as set in IP configuration, are always active.
video-reset-gpios:
description: Optional specifier for a GPIO that asserts video_aresetn.
maxItems: 1
ports:
$ref: /schemas/graph.yaml#/properties/ports
properties:
port@0:
$ref: /schemas/graph.yaml#/$defs/port-base
description: |
Input / sink port node, single endpoint describing the
CSI-2 transmitter.
properties:
endpoint:
$ref: /schemas/media/video-interfaces.yaml#
unevaluatedProperties: false
properties:
data-lanes:
description: |
This is required only in the sink port 0 endpoint which
connects to MIPI CSI-2 source like sensor.
The possible values are -
1 - For 1 lane enabled in IP.
1 2 - For 2 lanes enabled in IP.
1 2 3 - For 3 lanes enabled in IP.
1 2 3 4 - For 4 lanes enabled in IP.
items:
- const: 1
- const: 2
- const: 3
- const: 4
required:
- data-lanes
unevaluatedProperties: false
port@1:
$ref: /schemas/graph.yaml#/properties/port
description: |
Output / source port node, endpoint describing modules
connected the CSI-2 receiver.
required:
- compatible
- reg
- interrupts
- clocks
- clock-names
- ports
allOf:
- if:
required:
- xlnx,vfb
then:
required:
- xlnx,csi-pxl-format
else:
properties:
xlnx,csi-pxl-format: false
- if:
not:
required:
- xlnx,en-csi-v2-0
then:
properties:
xlnx,en-vcx: false
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
xcsi2rxss_1: csi2rx@a0020000 {
compatible = "xlnx,mipi-csi2-rx-subsystem-5.0";
reg = <0xa0020000 0x10000>;
interrupt-parent = <&gic>;
interrupts = <0 95 4>;
xlnx,csi-pxl-format = <0x2a>;
xlnx,vfb;
xlnx,en-active-lanes;
xlnx,en-csi-v2-0;
xlnx,en-vcx;
clock-names = "lite_aclk", "video_aclk";
clocks = <&misc_clk_0>, <&misc_clk_1>;
video-reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
/* Sink port */
reg = <0>;
csiss_in: endpoint {
data-lanes = <1 2 3 4>;
/* MIPI CSI-2 Camera handle */
remote-endpoint = <&camera_out>;
};
};
port@1 {
/* Source port */
reg = <1>;
csiss_out: endpoint {
remote-endpoint = <&vproc_in>;
};
};
};
};
...
|
