summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Expand)AuthorFilesLines
2011-07-01Bluetooth: Add Atheros AR3012 one PID/VID supportedSteven.Li2-1/+16
2011-06-23ssb: add __devinit to some functionsHauke Mehrtens6-32/+36
2011-06-23ath9k: enable support for AR9330Gabor Juhos1-0/+1
2011-06-23ath9k: add external_reset callback to ath9k_platfom_data for AR9330Gabor Juhos3-0/+37
2011-06-23ath9k: configure internal regulator for AR9330Gabor Juhos1-5/+20
2011-06-23ath9k: configure diversity based on eeprom contents for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: fix few register offsets for AR9330Gabor Juhos1-2/+2
2011-06-23ath9k: set diversity group for AR9330Gabor Juhos1-1/+4
2011-06-23ath9k: add fast_div_bias configuration for diversity group 1Gabor Juhos1-0/+83
2011-06-23ath9k: remove superfluous parenthesesGabor Juhos1-32/+30
2011-06-23ath9k: fix antenna diversity configuration for non AR9485 chipsGabor Juhos1-2/+8
2011-06-23ath9k: add a missing case statement to ath_ant_div_comb_alt_checkGabor Juhos1-0/+1
2011-06-23ath9k: use correct max_streams for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: enable antenna diversity for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: set NF limits for AR9330Gabor Juhos2-1/+6
2011-06-23ath9k: configure xpa bias level for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: use correct EEPROM base for AR9330Gabor Juhos1-0/+2
2011-06-23ath9k: enable tuning capacitance configuration for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: skip internal regulator configuration for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: enable TX/RX data byte swap for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: configure RF channel frequency for AR9330Gabor Juhos1-1/+13
2011-06-23ath9k: fix channel frequency calculation for AR9340Gabor Juhos1-1/+1
2011-06-23ath9k: read spur frequency information from eeprom for AR9330Gabor Juhos1-2/+2
2011-06-23ath9k: don't enable LDPC for AR9330Gabor Juhos1-1/+1
2011-06-23ath9k: use different BB watchdog timeout value for AR9330Gabor Juhos1-1/+4
2011-06-23ath9k: add AR9330 specific PLL initializationGabor Juhos1-1/+34
2011-06-23ath9k: initialize rx gain table for AR9330Gabor Juhos1-2/+22
2011-06-23ath9k: initialize tx gain table for AR9330Gabor Juhos1-4/+44
2011-06-23ath9k: initialize mode registers for AR9330Gabor Juhos2-1/+112
2011-06-23ath9k: add AR9330 initvalsGabor Juhos2-0/+2227
2011-06-23ath9k: add platform device id for AR9330Gabor Juhos1-0/+4
2011-06-23ath9k: add MAC revision detection for AR9330Gabor Juhos3-0/+11
2011-06-23ath9k: define device id for AR9330Gabor Juhos1-0/+1
2011-06-23ath9k: define mac version for AR9330Gabor Juhos2-1/+20
2011-06-23ath9k_hw: Fix calculation of PAPRD training power at 5GhzMohammed Shafi Shajakhan1-1/+17
2011-06-23mwifiex: remove casts of void pointersAmitkumar Karwar13-177/+129
2011-06-23zd1211rw: detect stalled beacon interrupt fasterJussi Kivilinna1-1/+2
2011-06-23zd1211rw: don't let zd_mac_config_beacon() run too long from beacon interrupt...Jussi Kivilinna1-7/+12
2011-06-23zd1211rw: handle lost read-reg interruptsJussi Kivilinna2-21/+109
2011-06-23zd1211rw: only update HW beacon if new beacon differs from currectJussi Kivilinna2-13/+64
2011-06-23zd1211rw: make 'handle_rx_packet: invalid, small RX packet' message debug-onlyJussi Kivilinna1-2/+2
2011-06-23zd1211rw: fix invalid signal values from deviceJussi Kivilinna2-2/+24
2011-06-23b43: HT-PHY: calibrate radio after switching channelRafał Miłecki1-1/+7
2011-06-23rt2x00: reset usb devices at probeStanislaw Gruszka1-0/+1
2011-06-23rt2x00: fix possible memory corruption in case of invalid rxdesc.sizeStanislaw Gruszka1-0/+13
2011-06-23b43: N-PHY: move declarations of chantables functions to correct filesRafał Miłecki3-8/+10
2011-06-23b43: N-PHY: update switching analog on/offRafał Miłecki1-4/+17
2011-06-23b43: HT-PHY: switch radio to requested channelRafał Miłecki2-1/+68
2011-06-23b43: HT-PHY: add place for implementing channel switchingRafał Miłecki1-2/+59
2011-06-23b43: HT-PHY: define standard structs for channel switchingRafał Miłecki5-0/+59
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-25 02:38:54 +0300