| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
|
|
When a VFLR interrupt is received during a VF reset initiated from a
different source, the VFLR may be not fully handled. This can
leave the VF in an undefined state.
To address this, set the I40E_VFLR_EVENT_PENDING bit again during VFLR
handling if the reset is not yet complete. This ensures the driver
will properly complete the VF reset in such scenarios.
Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Robert Malz <robert.malz@canonical.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The function i40e_vc_reset_vf attempts, up to 20 times, to handle a
VF reset request, using the return value of i40e_reset_vf as an indicator
of whether the reset was successfully triggered. Currently, i40e_reset_vf
always returns true, which causes new reset requests to be ignored if a
different VF reset is already in progress.
This patch updates the return value of i40e_reset_vf to reflect when
another VF reset is in progress, allowing the caller to properly use
the retry mechanism.
Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Robert Malz <robert.malz@canonical.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
When the device sends a specific input, an integer underflow can occur, leading
to MMIO write access to an invalid page.
Prevent the integer underflow by changing the type of related variables.
Signed-off-by: Kyungwook Boo <bookyungwook@gmail.com>
Link: https://lore.kernel.org/lkml/ffc91764-1142-4ba2-91b6-8c773f6f7095@gmail.com/T/
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
i40e, as well as ice, has a custom loop unrolling macro for unrolling
Tx descriptors filling on XSk xmit.
Replace i40e defs with generic unrolled_count(), which is also more
convenient as it allows passing defines as its argument, not hardcoded
values, while the loop declaration will still be a usual for-loop.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250206182630.3914318-3-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement "mdd-auto-reset-vf" priv-flag to handle Tx and Rx MDD events for VFs.
This flag is also used in other network adapters like ICE.
Usage:
- "on" - The problematic VF will be automatically reset
if a malformed descriptor is detected.
- "off" - The problematic VF will be disabled.
In cases where a VF sends malformed packets classified as malicious, it can
cause the Tx queue to freeze, rendering it unusable for several minutes. When
an MDD event occurs, this new implementation allows for a graceful VF reset to
quickly restore operational state.
Currently, VF queues are disabled if an MDD event occurs. This patch adds the
ability to reset the VF if a Tx or Rx MDD event occurs. It also includes MDD
event logging throttling to avoid dmesg pollution and unifies the format of
Tx and Rx MDD messages.
Note: Standard message rate limiting functions like dev_info_ratelimited()
do not meet our requirements. Custom rate limiting is implemented,
please see the code for details.
Co-developed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Co-developed-by: Padraig J Connolly <padraig.j.connolly@intel.com>
Signed-off-by: Padraig J Connolly <padraig.j.connolly@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250106221929.956999-13-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The last useof i40e_dcb_hw_get_num_tc() was removed in 2022 by
commit fe20371578ef ("Revert "i40e: Fix reset bw limit when DCB enabled
with 1 TC"")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-10-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
i40e_asq_send_command_v2() was added in 2022 by
commit 74073848b0d7 ("i40e: Add new versions of send ASQ command
functions")
but hasn't been used.
Remove it.
(The _atomic_v2 version of the function is used, so leave it).
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-9-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
i40e_commit_partition_bw_setting() was added in 2017 by
commit 4fc8c6763957 ("i40e: genericize the partition bandwidth control")
but hasn't been used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-8-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The last use of i40e_del_filter() was removed in 2016 by
commit 9569a9a4547d ("i40e: when adding or removing MAC filters, correctly
handle VLANs")
Remove it.
Fix up a comment that referenced it.
Note: The __ version of this function is still used.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-7-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The last use of i40e_get_cur_guaranteed_fd_count() was removed in 2015 by
commit 04294e38a451 ("i40e: FD filters flush policy changes")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-6-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
i40e_add_pinfo_to_list() was added in 2017 by
commit 1d5c960c5ef5 ("i40e: new AQ commands")
i40e_find_section_in_profile() was added in 2019 by
commit cdc594e00370 ("i40e: Implement DDP support in i40e driver")
Neither have been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-5-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
i40e_read_phy_register() and i40e_write_phy_register() were added in
2016 by
commit f62ba91458b5 ("i40e: Add functions which apply correct PHY access
method for read and write operation")
but haven't been used.
Remove them.
(There are more specific _clause* variants of these functions
that are still used.)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-4-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
i40e_blink_phy_link_led() was added in 2016 by
commit fd077cd3399b ("i40e: Add functions to blink led on 10GBaseT PHY")
but hasn't been used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-3-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
i40e_aq_add_mirrorrule(), i40e_aq_delete_mirrorrule() and
i40e_aq_set_vsi_vlan_promisc() were added in 2016 by
commit 7bd6875bef70 ("i40e: APIs to Add/remove port mirroring rules")
but haven't been used.
They were the last user of i40e_mirrorrule_op().
i40e_aq_rearrange_nvm() was added in 2018 by
commit f05798b4ff82 ("i40e: Add AQ command for rearrange NVM structure")
but hasn't been used.
i40e_aq_restore_lldp() was added in 2019 by
commit c65e78f87f81 ("i40e: Further implementation of LLDP")
but hasn't been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-2-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, xsk_buff_add_frag() only adds the frag to pool's linked list,
not doing anything with the &xdp_buff. The drivers do that manually and
the logic is the same.
Make it really add an skb frag, just like xdp_buff_add_frag() does that,
and freeing frags on error if needed. This allows to remove repeating
code from i40e and ice and not add the same code again and again.
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20241218174435.1445282-5-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clean up the existing export namespace code along the same lines of
commit 33def8498fdd ("treewide: Convert macro and uses of __section(foo)
to __section("foo")") and for the same reason, it is not desired for the
namespace argument to be a macro expansion itself.
Scripted using
git grep -l -e MODULE_IMPORT_NS -e EXPORT_SYMBOL_NS | while read file;
do
awk -i inplace '
/^#define EXPORT_SYMBOL_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/^#define MODULE_IMPORT_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/MODULE_IMPORT_NS/ {
$0 = gensub(/MODULE_IMPORT_NS\(([^)]*)\)/, "MODULE_IMPORT_NS(\"\\1\")", "g");
}
/EXPORT_SYMBOL_NS/ {
if ($0 ~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+),/) {
if ($0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/ &&
$0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(\)/ &&
$0 !~ /^my/) {
getline line;
gsub(/[[:space:]]*\\$/, "");
gsub(/[[:space:]]/, "", line);
$0 = $0 " " line;
}
$0 = gensub(/(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/,
"\\1(\\2, \"\\3\")", "g");
}
}
{ print }' $file;
done
Requested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://mail.google.com/mail/u/2/#inbox/FMfcgzQXKWgMmjdFwwdsfgxzKpVHWPlc
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge in late fixes to prepare for the 6.13 net-next PR.
Conflicts:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
721aa69e708b net: phy: convert eee_broken_modes to a linkmode bitmap
https://lore.kernel.org/all/20241118135512.1039208b@canb.auug.org.au/
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
2160428bcb20 net: txgbe: fix null pointer to pcs
2160428bcb20 net: txgbe: remove GPIO interrupt controller
Adjacent commits:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
516a5f11eb97 net: phy: respect cached advertising when re-enabling EEE
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently when FDB entries are added to or deleted from a VXLAN netdevice,
the VXLAN driver emits one notification, including the VXLAN-specific
attributes. The core however always sends a notification as well, a generic
one. Thus two notifications are unnecessarily sent for these operations. A
similar situation comes up with bridge driver, which also emits
notifications on its own:
# ip link add name vx type vxlan id 1000 dstport 4789
# bridge monitor fdb &
[1] 1981693
# bridge fdb add de:ad:be:ef:13:37 dev vx self dst 192.0.2.1
de:ad:be:ef:13:37 dev vx dst 192.0.2.1 self permanent
de:ad:be:ef:13:37 dev vx self permanent
In order to prevent this duplicity, add a paremeter to ndo_fdb_add,
bool *notified. The flag is primed to false, and if the callee sends a
notification on its own, it sets it to true, thus informing the core that
it should not generate another notification.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/cbf6ae8195e85cbf922f8058ce4eba770f3b71ed.1731589511.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After assembling the new private flags on a PF, the operation to determine
the changed flags uses the wrong bitmaps. Instead of xor-ing orig_flags
with new_flags, it uses the still unchanged pf->flags, thus changed_flags
is always 0.
Fix it by using the correct bitmaps.
The issue was discovered while debugging why disabling source pruning
stopped working with release 6.7. Although the new flags will be copied to
pf->flags later on in that function, disabling source pruning requires
a reset of the PF, which was skipped due to this bug.
Disabling source pruning:
$ sudo ethtool --set-priv-flags eno1 disable-source-pruning on
$ sudo ethtool --show-priv-flags eno1
Private flags for eno1:
MFP : off
total-port-shutdown : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
link-down-on-close : off
legacy-rx : off
disable-source-pruning: on
disable-fw-lldp : off
rs-fec : off
base-r-fec : off
vf-vlan-pruning : off
Regarding reproducing:
I observed the issue with a rather complicated lab setup, where
* two VLAN interfaces are created on eno1
* each with a different MAC address assigned
* each moved into a separate namespace
* both VLANs are bridged externally, so they form a single layer 2 network
The external bridge is done via a channel emulator adding packet loss and
delay and the application in the namespaces tries to send/receive traffic
and measure the performance. Sender and receiver are separated by
namespaces, yet the network card "sees its own traffic" send back to it.
To make that work, source pruning has to be disabled.
Cc: stable@vger.kernel.org
Fixes: 70756d0a4727 ("i40e: Use DECLARE_BITMAP for flags and hw_features fields in i40e_pf")
Signed-off-by: Peter Große <pegro@friiks.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20241113210705.1296408-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a race condition in the i40e driver that leads to MAC/VLAN filters
becoming corrupted and leaking. Address the issue that occurs under
heavy load when multiple threads are concurrently modifying MAC/VLAN
filters by setting mac and port VLAN.
1. Thread T0 allocates a filter in i40e_add_filter() within
i40e_ndo_set_vf_port_vlan().
2. Thread T1 concurrently frees the filter in __i40e_del_filter() within
i40e_ndo_set_vf_mac().
3. Subsequently, i40e_service_task() calls i40e_sync_vsi_filters(), which
refers to the already freed filter memory, causing corruption.
Reproduction steps:
1. Spawn multiple VFs.
2. Apply a concurrent heavy load by running parallel operations to change
MAC addresses on the VFs and change port VLANs on the host.
3. Observe errors in dmesg:
"Error I40E_AQ_RC_ENOSPC adding RX filters on VF XX,
please set promiscuous on manually for VF XX".
Exact code for stable reproduction Intel can't open-source now.
The fix involves implementing a new intermediate filter state,
I40E_FILTER_NEW_SYNC, for the time when a filter is on a tmp_add_list.
These filters cannot be deleted from the hash list directly but
must be removed using the full process.
Fixes: 278e7d0b9d68 ("i40e: store MAC/VLAN filters in a hash with the MAC Address as key")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch addresses a macvlan leak issue in the i40e driver caused by
concurrent access to vsi->mac_filter_hash. The leak occurs when multiple
threads attempt to modify the mac_filter_hash simultaneously, leading to
inconsistent state and potential memory leaks.
To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing
vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock),
ensuring atomic operations and preventing concurrent access.
Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in
i40e_add_mac_filter() to help catch similar issues in the future.
Reproduction steps:
1. Spawn VFs and configure port vlan on them.
2. Trigger concurrent macvlan operations (e.g., adding and deleting
portvlan and/or mac filters).
3. Observe the potential memory leak and inconsistent state in the
mac_filter_hash.
This synchronization ensures the integrity of the mac_filter_hash and prevents
the described leak.
Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add "EEE: Enabled/Disabled" to dmesg for supported X710 Base-T/KR/KX
cards. According to the IEEE standard report the EEE ability and the
EEE Link Partner ability. Use the kernel's 'ethtool_keee' structure
and report EEE link modes.
Example:
dmesg | grep 'NIC Link is'
ethtool --show-eee <device>
Before:
NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
Supported EEE link modes: Not reported
Advertised EEE link modes: Not reported
Link partner advertised EEE link modes: Not reported
After:
NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None, EEE: Enabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Link partner advertised EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
First part of "net: Make timestamping selectable" from Kory Maincent.
Change the driver-facing type already to lower rebasing pain.
Link: https://lore.kernel.org/20240709-feature_ptp_netnext-v17-0-b5317f50df2a@bootlin.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-07-11 (net/intel)
This series contains updates to most Intel network drivers.
Tony removes MODULE_AUTHOR from drivers containing the entry.
Simon Horman corrects a kdoc entry for i40e.
Pawel adds implementation for devlink param "local_forwarding" on ice.
Michal removes unneeded call, and code, for eswitch rebuild for ice.
Sasha removed a no longer used field from igc.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Remove the internal 'eee_advert' field
ice: remove eswitch rebuild
ice: Add support for devlink local_forwarding param
i40e: correct i40e_addr_to_hkey() name in kdoc
net: intel: Remove MODULE_AUTHORs
====================
Link: https://patch.msgid.link/20240711201932.2019925-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
f7ce5eb2cb79 ("bnxt_en: Fix crash in bnxt_get_max_rss_ctx_ring()")
20c8ad72eb7f ("eth: bnxt: use the RSS context XArray instead of the local list")
Adjacent changes:
net/ethtool/ioctl.c
503757c80928 ("net: ethtool: Fix RSS setting")
eac9122f0c41 ("net: ethtool: record custom RSS contexts in the XArray")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove wrong EIO to EGAIN conversion and pass all errors as is.
After commit 230f3d53a547 ("i40e: remove i40e_status"), which should only
replace F/W specific error codes with Linux kernel generic, all EIO errors
suddenly started to be converted into EAGAIN which leads nvmupdate to retry
until it timeouts and sometimes fails after more than 20 minutes in the
middle of NVM update, so NVM becomes corrupted.
The bug affects users only at the time when they try to update NVM, and
only F/W versions that generate errors while nvmupdate. For example, X710DA2
with 0x8000ECB7 F/W is affected, but there are probably more...
Command for reproduction is just NVM update:
./nvmupdate64
In the log instead of:
i40e_nvmupd_exec_aq err I40E_ERR_ADMIN_QUEUE_ERROR aq_err I40E_AQ_RC_ENOMEM)
appears:
i40e_nvmupd_exec_aq err -EIO aq_err I40E_AQ_RC_ENOMEM
i40e: eeprom check failed (-5), Tx/Rx traffic disabled
The problematic code did silently convert EIO into EAGAIN which forced
nvmupdate to ignore EAGAIN error and retry the same operation until timeout.
That's why NVM update takes 20+ minutes to finish with the fail in the end.
Fixes: 230f3d53a547 ("i40e: remove i40e_status")
Co-developed-by: Kelvin Kang <kelvin.kang@intel.com>
Signed-off-by: Kelvin Kang <kelvin.kang@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240710224455.188502-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/act_ct.c
26488172b029 ("net/sched: Fix UAF when resolving a clash")
3abbd7ed8b76 ("act_ct: prepare for stolen verdict coming from conntrack and nat engine")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct name of i40e_addr_to_hkey() in it's kdoc.
kernel-doc -none reports:
drivers/net/ethernet/intel/i40e/i40e.h:739: warning: expecting prototype for i40e_mac_to_hkey(). Prototype was for i40e_addr_to_hkey() instead
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We are moving away from the Sourceforge email address. Rather than
removing or updating the email for the affected entries, remove the
MODULE_AUTHOR altogether as its usage is incorrect [1].
Link: https://lore.kernel.org/netdev/20200626115236.7f36d379@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/ [1]
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com> # libeth, libie
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The commit 6533e558c650 ("i40e: Fix reset path while removing
the driver") introduced a new PF state "__I40E_IN_REMOVE" to block
modifying the XDP program while the driver is being removed.
Unfortunately, such a change is useful only if the ".ndo_bpf()"
callback was called out of the rmmod context because unloading the
existing XDP program is also a part of driver removing procedure.
In other words, from the rmmod context the driver is expected to
unload the XDP program without reporting any errors. Otherwise,
the kernel warning with callstack is printed out to dmesg.
Example failing scenario:
1. Load the i40e driver.
2. Load the XDP program.
3. Unload the i40e driver (using "rmmod" command).
The example kernel warning log:
[ +0.004646] WARNING: CPU: 94 PID: 10395 at net/core/dev.c:9290 unregister_netdevice_many_notify+0x7a9/0x870
[...]
[ +0.010959] RIP: 0010:unregister_netdevice_many_notify+0x7a9/0x870
[...]
[ +0.002726] Call Trace:
[ +0.002457] <TASK>
[ +0.002119] ? __warn+0x80/0x120
[ +0.003245] ? unregister_netdevice_many_notify+0x7a9/0x870
[ +0.005586] ? report_bug+0x164/0x190
[ +0.003678] ? handle_bug+0x3c/0x80
[ +0.003503] ? exc_invalid_op+0x17/0x70
[ +0.003846] ? asm_exc_invalid_op+0x1a/0x20
[ +0.004200] ? unregister_netdevice_many_notify+0x7a9/0x870
[ +0.005579] ? unregister_netdevice_many_notify+0x3cc/0x870
[ +0.005586] unregister_netdevice_queue+0xf7/0x140
[ +0.004806] unregister_netdev+0x1c/0x30
[ +0.003933] i40e_vsi_release+0x87/0x2f0 [i40e]
[ +0.004604] i40e_remove+0x1a1/0x420 [i40e]
[ +0.004220] pci_device_remove+0x3f/0xb0
[ +0.003943] device_release_driver_internal+0x19f/0x200
[ +0.005243] driver_detach+0x48/0x90
[ +0.003586] bus_remove_driver+0x6d/0xf0
[ +0.003939] pci_unregister_driver+0x2e/0xb0
[ +0.004278] i40e_exit_module+0x10/0x5f0 [i40e]
[ +0.004570] __do_sys_delete_module.isra.0+0x197/0x310
[ +0.005153] do_syscall_64+0x85/0x170
[ +0.003684] ? syscall_exit_to_user_mode+0x69/0x220
[ +0.004886] ? do_syscall_64+0x95/0x170
[ +0.003851] ? exc_page_fault+0x7e/0x180
[ +0.003932] entry_SYSCALL_64_after_hwframe+0x71/0x79
[ +0.005064] RIP: 0033:0x7f59dc9347cb
[ +0.003648] Code: 73 01 c3 48 8b 0d 65 16 0c 00 f7 d8 64 89 01 48 83
c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f
05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 35 16 0c 00 f7 d8 64 89 01 48
[ +0.018753] RSP: 002b:00007ffffac99048 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ +0.007577] RAX: ffffffffffffffda RBX: 0000559b9bb2f6e0 RCX: 00007f59dc9347cb
[ +0.007140] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 0000559b9bb2f748
[ +0.007146] RBP: 00007ffffac99070 R08: 1999999999999999 R09: 0000000000000000
[ +0.007133] R10: 00007f59dc9a5ac0 R11: 0000000000000206 R12: 0000000000000000
[ +0.007141] R13: 00007ffffac992d8 R14: 0000559b9bb2f6e0 R15: 0000000000000000
[ +0.007151] </TASK>
[ +0.002204] ---[ end trace 0000000000000000 ]---
Fix this by checking if the XDP program is being loaded or unloaded.
Then, block only loading a new program while "__I40E_IN_REMOVE" is set.
Also, move testing "__I40E_IN_REMOVE" flag to the beginning of XDP_SETUP
callback to avoid unnecessary operations and checks.
Fixes: 6533e558c650 ("i40e: Fix reset path while removing the driver")
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240708230750.625986-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240607-next-2024-06-03-intel-next-batch-v3-1-d1470cee3347@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When EEH events occurs, the callback functions in the i40e, which are
managed by the EEH driver, will completely suspend and resume all IO
operations.
- In the PCI error detected callback, replaced i40e_prep_for_reset()
with i40e_io_suspend(). The change is to fully suspend all I/O
operations
- In the PCI error slot reset callback, replaced pci_enable_device_mem()
with pci_enable_device(). This change enables both I/O and memory of
the device.
- In the PCI error resume callback, replaced i40e_handle_reset_warning()
with i40e_io_resume(). This change allows the system to resume I/O
operations
Fixes: a5f3d2c17b07 ("powerpc/pseries/pci: Add MSI domains")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Robert Thomas <rob.thomas@ibm.com>
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-3-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Two new functions, i40e_io_suspend() and i40e_io_resume(), have been
introduced. These functions were factored out from the existing
i40e_suspend() and i40e_resume() respectively. This factoring was
done due to concerns about the logic of the I40E_SUSPENSED state, which
caused the device to be unable to recover. The functions are now used
in the EEH handling for device suspend/resume callbacks.
The function i40e_enable_mc_magic_wake() has been moved ahead of
i40e_io_suspend() to ensure it is declared before being used.
Tested-by: Robert Thomas <rob.thomas@ibm.com>
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-2-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
* tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping:
dma: fix DMA sync for drivers not calling dma_set_mask*()
xsk: use generic DMA sync shortcut instead of a custom one
page_pool: check for DMA sync shortcut earlier
page_pool: don't use driver-set flags field directly
page_pool: make sure frag API fields don't span between cachelines
iommu/dma: avoid expensive indirect calls for sync operations
dma: avoid redundant calls for sync operations
dma: compile-out DMA sync op calls when not used
iommu/dma: fix zeroing of bounce buffer padding used by untrusted devices
swiotlb: remove alloc_size argument to swiotlb_tbl_map_single()
Documentation/core-api: add swiotlb documentation
|
|
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
XSk infra's been using its own DMA sync shortcut to try avoiding
redundant function calls. Now that there is a generic one, remove
the custom implementation and rely on the generic helpers.
xsk_buff_dma_sync_for_cpu() doesn't need the second argument anymore,
remove it.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c94510 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add helper i40e_vsi_reconfig_tc(vsi) that configures TC
for given VSI using previously stored TC bitmap.
Effectively replaces open-coded patterns:
enabled_tc = vsi->tc_config.enabled_tc;
vsi->tc_config.enabled_tc = 0;
i40e_vsi_config_tc(vsi, enabled_tc);
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a helper to access main VEB:
i40e_pf_get_main_veb(pf) replaces 'pf->veb[pf->lan_veb]'
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In the driver code there are 3 types of checks whether given
VSI is main or not:
1. vsi->type ==/!= I40E_VSI_MAIN
2. vsi ==/!= pf->vsi[pf->lan_vsi]
3. vsi->seid ==/!= pf->vsi[pf->lan_vsi]->seid
All of them are equivalent and can be consolidated. Convert cases
2 and 3 to case 1.
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add simple helper i40e_pf_get_main_vsi(pf) to access main VSI
that replaces pattern 'pf->vsi[pf->lan_vsi]'
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 07d44190a389 ("i40e/i40evf: Detect and recover hung queue
scenario") changes i40e_detect_recover_hung() argument type from
i40e_pf* to i40e_vsi* to be shareable by both i40e and i40evf.
Because the i40evf does not exist anymore and the function is
exclusively used by i40e we can revert this change.
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 0ef2d5afb12d ("i40e: KISS the client interface") simplified
the client interface so in practice it supports only one client
per i40e netdev. But we have still 2 notification functions that
uses as parameter a pointer to VSI of netdevice associated with
the client. After the mentioned commit only possible and used
VSI is the main (LAN) VSI.
So refactor these functions so they are called with PF pointer argument
and the associated VSI (LAN) is taken inside them.
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The field is initialized always to zero and it is never read.
Remove it.
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
