| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 4f563a64732d ("block: add a max_user_discard_sectors queue
limit") changed block core to set max_discard_sectors to:
min(lim->max_hw_discard_sectors, lim->max_user_discard_sectors)
Since commit 1c0e720228ad ("dm: use queue_limits_set") it was reported
dm-thinp was failing in a few fstests (generic/347 and generic/405)
with the first WARN_ON_ONCE in dm_cell_key_has_valid_range() being
reported, e.g.:
WARNING: CPU: 1 PID: 30 at drivers/md/dm-bio-prison-v1.c:128 dm_cell_key_has_valid_range+0x3d/0x50
blk_set_stacking_limits() sets max_user_discard_sectors to UINT_MAX,
so given how block core now sets max_discard_sectors (detailed above)
it follows that blk_stack_limits() stacks up the underlying device's
max_hw_discard_sectors and max_discard_sectors is set to match it. If
max_hw_discard_sectors exceeds dm's BIO_PRISON_MAX_RANGE, then
dm_cell_key_has_valid_range() will trigger the warning with:
WARN_ON_ONCE(key->block_end - key->block_begin > BIO_PRISON_MAX_RANGE)
Aside from this warning, the discard will fail. Fix this and other DM
issues by governing discard support in terms of max_hw_discard_sectors
instead of max_discard_sectors.
Reported-by: Theodore Ts'o <tytso@mit.edu>
Fixes: 1c0e720228ad ("dm: use queue_limits_set")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
dm-error is used in several test cases in the xfstests test suite to
check the handling of IO errors in file systems. However, with several
file systems getting native support for zoned block devices (e.g.
btrfs and f2fs), dm-error's lack of zoned block device support creates
problems as the file system attempts executing zone commands (e.g. a
zone append operation) against a dm-error non-zoned block device,
which causes various issues in the block layer (e.g. WARN_ON
triggers).
This commit adds supports for zoned block devices to dm-error, allowing
a DM device table containing an error target to be exposed as a zoned
block device (if all targets have a compatible zoned model support and
mapping). This is done as follows:
1) Allow passing 2 arguments to an error target, similar to dm-linear:
a backing device and a start sector. These arguments are optional and
dm-error retains its characteristics if the arguments are not
specified.
2) Implement the iterate_devices method so that dm-core can normally
check the zone support and restrictions (e.g. zone alignment of the
targets). When the backing device arguments are not specified, the
iterate_devices method never calls the fn() argument.
When no backing device is specified, as before, we assume that the DM
device is not zoned. When the backing device arguments are specified,
the zoned model of the DM device will depend on the backing device
type:
- If the backing device is zoned and its model and mapping is
compatible with other targets of the device, the resulting device
will be zoned, with the dm-error mapped portion always returning
errors (similar to the default non-zoned case).
- If the backing device is not zoned, then the DM device will not be
either.
This zone support for dm-error requires the definition of a functional
report_zones operation so that dm_revalidate_zones() can operate
correctly and resources for emulating zone append operations
initialized. This is necessary for cases where dm-error is used to
partially map a device and have an overall correct handling of zone
append. This means that dm-error does not fail report zones operations.
Two changes that are not obvious are included to avoid issues:
1) dm_table_supports_zoned_model() is changed to directly check if
the backing device of a wildcard target (= dm-error target) is
zoned. Otherwise, we wouldn't be able to catch the invalid setup of
dm-error without a backing device (non zoned case) being combined
with zoned targets.
2) dm_table_supports_dax() is modified to return false if the wildcard
target is found. Otherwise, when dm-error is set without a backing
device, we end up with a NULL pointer dereference in
set_dax_synchronous (dax_dev is NULL). This is consistent with the
current behavior because dm_table_supports_dax() always returned
false for targets that do not define the iterate_devices method.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Simplifies each DM target's init method by making dm_register_target()
responsible for its error reporting (on behalf of targets).
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Add io_err_io_hints() and set discard limits so that the zero target
advertises support for discards.
The error target will return -EIO for discards.
This is useful when the user combines dm-error with other
discard-supporting targets in the same table; without dm-error
support, discards would be disabled for the whole combined device.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
'GPL-2.0-only' is used instead of 'GPL-2.0' because SPDX has
deprecated its use.
Suggested-by: John Wiele <jwiele@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Up till now, dax_direct_access() is used implicitly for normal
access, but for the purpose of recovery write, dax range with
poison is requested. To make the interface clear, introduce
enum dax_access_mode {
DAX_ACCESS,
DAX_RECOVERY_WRITE,
}
where DAX_ACCESS is used for normal dax access, and
DAX_RECOVERY_WRITE is used for dax recovery write.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Vivek Goyal <vgoyal@redhat.com>
Link: https://lore.kernel.org/r/165247982851.52965.11024212198889762949.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
After commit 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via
blk_insert_cloned_request feedback"), map_request() will requeue the tio
when issued clone request return BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE.
Thus, if device driver status is error, a tio may be requeued multiple
times until the return value is not DM_MAPIO_REQUEUE. That means
type->start_io may be called multiple times, while type->end_io is only
called when IO complete.
In fact, even without commit 396eaf21ee17, setup_clone() failure can
also cause tio requeue and associated missed call to type->end_io.
The service-time path selector selects path based on in_flight_size,
which is increased by st_start_io() and decreased by st_end_io().
Missed calls to st_end_io() can lead to in_flight_size count error and
will cause the selector to make the wrong choice. In addition,
queue-length path selector will also be affected.
To fix the problem, call type->end_io in ->release_clone_rq before tio
requeue. map_info is passed to ->release_clone_rq() for map_request()
error path that result in requeue.
Fixes: 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Cc: stable@vger.kernl.org
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Instead use the special DM_MAPIO_KILL return value to return -EIO just
like we do for the request based path. Note that dm-log-writes returned
-ENOMEM in a few places, which now becomes -EIO instead. No consumer
treats -ENOMEM special so this shouldn't be an issue (and it should
use a mempool to start with to make guaranteed progress).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has been in multiple -next releases. There were a few
late breaking fixes and small features that got added in the last
couple days, but the whole set has received a build success
notification from the kbuild robot.
Change summary:
- Region media error reporting: A libnvdimm region device is the
parent to one or more namespaces. To date, media errors have been
reported via the "badblocks" attribute attached to pmem block
devices for namespaces in "raw" or "memory" mode. Given that
namespaces can be in "device-dax" or "btt-sector" mode this new
interface reports media errors generically, i.e. independent of
namespace modes or state.
This subsequently allows userspace tooling to craft "ACPI 6.1
Section 9.20.7.6 Function Index 4 - Clear Uncorrectable Error"
requests and submit them via the ioctl path for NVDIMM root bus
devices.
- Introduce 'struct dax_device' and 'struct dax_operations': Prompted
by a request from Linus and feedback from Christoph this allows for
dax capable drivers to publish their own custom dax operations.
This fixes the broken assumption that all dax operations are
related to a persistent memory device, and makes it easier for
other architectures and platforms to add customized persistent
memory support.
- 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger
memory controllers to drain write-pending buffers that would
otherwise be flushed automatically by the platform ADR
(asynchronous-DRAM-refresh) mechanism at a power loss event.
Support for "locked" DIMMs is included to prevent namespaces from
surfacing when the namespace label data area is locked. Finally,
fixes for various reported deadlocks and crashes, also tagged for
-stable.
- ACPI / nfit driver updates: General updates of the nfit driver to
add DSM command overrides, ACPI 6.1 health state flags support, DSM
payload debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
- commmit 565851c972b5 "device-dax: fix sysfs attribute deadlock":
Tested-by: Yi Zhang <yizhan@redhat.com>
- commit 23f498448362 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (52 commits)
libnvdimm, pfn: fix 'npfns' vs section alignment
libnvdimm: handle locked label storage areas
libnvdimm: convert NDD_ flags to use bitops, introduce NDD_LOCKED
brd: fix uninitialized use of brd->dax_dev
block, dax: use correct format string in bdev_dax_supported
device-dax: fix sysfs attribute deadlock
libnvdimm: restore "libnvdimm: band aid btt vs clear poison locking"
libnvdimm: fix nvdimm_bus_lock() vs device_lock() ordering
libnvdimm: rework region badblocks clearing
acpi, nfit: kill ACPI_NFIT_DEBUG
libnvdimm: fix clear length of nvdimm_forget_poison()
libnvdimm, pmem: fix a NULL pointer BUG in nd_pmem_notify
libnvdimm, region: sysfs trigger for nvdimm_flush()
libnvdimm: fix phys_addr for nvdimm_clear_poison
x86, dax, pmem: remove indirection around memcpy_from_pmem()
block: remove block_device_operations ->direct_access()
block, dax: convert bdev_dax_supported() to dax_direct_access()
filesystem-dax: convert to dax_direct_access()
Revert "block: use DAX for partition table reads"
ext2, ext4, xfs: retrieve dax_device for iomap operations
...
|
|
This untangles the DM_MAPIO_* values returned from ->clone_and_map_rq
from the error codes used by the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Arrange for dm to lookup the dax services available from member devices.
Update the dax-capable targets, linear and stripe, to route dax
operations to the underlying device. Changes the target-internal
->direct_access() method to more closely align with the dax_operations
->direct_access() calling convention.
Cc: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
DM already calls blk_mq_alloc_request on the request_queue of the
underlying device if it is a blk-mq device. But now that we allow drivers
to allocate additional data and initialize it ahead of time we need to do
the same for all drivers. Doing so and using the new cmd_size
infrastructure in the block layer greatly simplifies the dm-rq and mpath
code, and should also make arbitrary combinations of SQ and MQ devices
with SQ or MQ device mapper tables easily possible as a further step.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
|
|
Allow the error target to replace an existing DAX-enabled target.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Add some seperation between bio-based and request-based DM core code.
'struct mapped_device' and other DM core only structures and functions
have been moved to dm-core.h and all relevant DM core .c files have been
updated to include dm-core.h rather than dm.h
DM targets should _never_ include dm-core.h!
[block core merge conflict resolution from Stephen Rothwell]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
The DM_TARGET_WILDCARD feature indicates that the "error" target may
replace any target; even immutable targets. This feature will be useful
to preserve the ability to replace the "multipath" target even once it
is formally converted over to having the DM_TARGET_IMMUTABLE feature.
Also, implicit in the DM_TARGET_WILDCARD feature flag being set is that
.map, .map_rq, .clone_and_map_rq and .release_clone_rq are all defined
in the target_type.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
For blk-mq request-based DM the responsibility of allocating a cloned
request is transfered from DM core to the target type. Doing so
enables the cloned request to be allocated from the appropriate
blk-mq request_queue's pool (only the DM target, e.g. multipath, can
know which block device to send a given cloned request to).
Care was taken to preserve compatibility with old-style block request
completion that requires request-based DM _not_ acquire the clone
request's queue lock in the completion path. As such, there are now 2
different request-based DM target_type interfaces:
1) the original .map_rq() interface will continue to be used for
non-blk-mq devices -- the preallocated clone request is passed in
from DM core.
2) a new .clone_and_map_rq() and .release_clone_rq() will be used for
blk-mq devices -- blk_get_request() and blk_put_request() are used
respectively from these hooks.
dm_table_set_type() was updated to detect if the request-based target is
being stacked on blk-mq devices, if so DM_TYPE_MQ_REQUEST_BASED is set.
DM core disallows switching the DM table's type after it is set. This
means that there is no mixing of non-blk-mq and blk-mq devices within
the same request-based DM table.
[This patch was started by Keith and later heavily modified by Mike]
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
It may be useful to switch a request-based table to the "error" target.
Enhance the DM core to allow a hybrid target_type which is capable of
handling either bios (via .map) or requests (via .map_rq).
Add a request-based map function (.map_rq) to the "error" target_type;
making it DM's first hybrid target. Train dm_table_set_type() to prefer
the mapped device's established type (request-based or bio-based). If
the mapped device doesn't have an established type default to making the
table with the hybrid target(s) bio-based.
Tested 'dmsetup wipe_table' to work on both bio-based and request-based
devices.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use 'bio' in the name of variables and functions that deal with
bios rather than 'request' to avoid confusion with the normal
block layer use of 'request'.
No functional changes.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch removes map_info from bio-based device mapper targets.
map_info is still used for request-based targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Have the error target respond to a discard request with a hard -EIO
rather than fail the request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
The tt_internal is really just a list_head to manage registered target_type
in a double linked list,
Here embed the list_head into target_type directly,
1. to avoid kmalloc/kfree;
2. then tt_internal is really unneeded;
Cc: stable@kernel.org
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
|
|
The tt_internal's 'use' field is superfluous: the module's refcount can do
the work properly. An acceptable side-effect is that this increases the
reference counts reported by 'lsmod'.
Remove the superfluous test when removing a target module.
[Crash possible without this on SMP - agk]
Cc: stable@kernel.org
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
|
|
Change dm_unregister_target to return void and use BUG() for error
reporting.
dm_unregister_target can only fail because of programming bug in the
target driver. It can't fail because of user's behavior or disk errors.
This patch changes unregister_target to return void and use BUG if
someone tries to unregister non-registered target or unregister target
that is in use.
This patch removes code duplication (testing of error codes in all dm
targets) and reports bugs in just one place, in dm_unregister_target. In
some target drivers, these return codes were ignored, which could lead
to a situation where bugs could be missed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Convert kmalloc() + memset() to kzalloc().
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Tidy device-mapper error messages to include context information
automatically.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
