| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for ADIS16501 device in already existing ADIS16475
driver.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Ramona Gradinariu <ramona.bolboaca13@gmail.com>
Link: https://lore.kernel.org/r/20240527142618.275897-3-ramona.bolboaca13@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The Bosch BMI323 is a 6-axis low-power IMU that provide measurements for
acceleration, angular rate, and temperature. This sensor includes
motion-triggered interrupt features, such as a step counter, tap detection,
and activity/inactivity interrupt capabilities.
The driver supports various functionalities, including data ready, FIFO
data handling, and events such as tap detection, step counting, and
activity interrupts.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20231013034808.8948-3-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In rare randconfig builds, the missing CRC32 helper causes
a link error:
ld.lld: error: undefined symbol: crc32_le
>>> referenced by usercopy_64.c
>>> vmlinux.o:(adis16480_trigger_handler)
Fixes: 941f130881fa ("iio: adis16480: support burst read function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230131094616.130238-1-arnd@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add the core driver for the BNO055 IMU from Bosch. This IMU can be
connected via both serial and I2C busses; separate patches will add support
for them.
The driver supports "AMG" (Accelerometer, Magnetometer, Gyroscope) mode,
that provides raw data from the said internal sensors, and a couple of
"fusion" modes (i.e. the IMU also does calculations in order to provide
euler angles, quaternions, linear acceleration and gravity measurements).
In fusion modes the AMG data is still available (with some calibration
refinements done by the IMU), but certain settings such as low pass filters
cut-off frequency and sensors' ranges are fixed, while in AMG mode they can
be customized; this is why AMG mode can still be interesting.
Signed-off-by: Andrea Merello <andrea.merello@iit.it>
Link: https://lore.kernel.org/r/20220907132205.28021-9-andrea.merello@iit.it
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We can utilize separate drivers for accelerometer and magnetometer,
so here is the glue driver to enable LSM9DS0 IMU support.
The idea was suggested by Crestez Dan Leonard in [1]. The proposed change
was sent as RFC due to race condition concerns, which are indeed possible.
In order to amend the initial change, I went further by providing a specific
multi-instantiate probe driver that reuses existing accelerometer and
magnetometer.
[1]: https://lore.kernel.org/patchwork/patch/670353/
Suggested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: mr.lahorde@laposte.net
Cc: Matija Podravec <matija_podravec@fastmail.fm>
Cc: Sergey Borishchenko <borischenko.sergey@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210414195454.84183-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add 3 modules: inv-icm42600, inv-icm42600-i2c, inv-icm42600-spi.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Support ADIS16475 and similar IMU devices. These devices are
a precision, miniature MEMS inertial measurement unit (IMU) that
includes a triaxial gyroscope and a triaxial accelerometer. Each
inertial sensor combines with signal conditioning that optimizes
dynamic performance.
The driver adds support for the following devices:
* adis16470, adis16475, adis16477, adis16465, adis16467, adis16500,
adis16505, adis16507.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis
magnetometer combined into a single package. The device features a
selectable I2C or point-to-point SPI serial interface with 14-bit
accelerometer and 16-bit magnetometer ADC resolution along with
smart-embedded functions.
FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of
±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT.
Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user
for each sensor. Interleaved magnetic and acceleration data is available
at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN
package and it is guaranteed to operate over the extended temperature
range of –40 °C to +85 °C.
TODO: Trigger and IRQ configuration support
Datasheet:
http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADIS16460 device is a complete inertial system that includes a triaxial
gyroscope and a triaxial accelerometer. It's more simplified design than
that of the ADIS16480, and does not offer the triaxial magnetometers &
pressure sensors. It does also have a temperature sensor (like the
ADIS16480).
Since it is part of the ADIS16XXX family, it re-uses parts of the ADIS
library.
Naturally, the register map is different and much more simplified than the
ADIS16480 subfamily, so it cannot be integrated into that driver. A major
difference is that the registers are not paged.
One thing that is particularly special about it, is that it requires a
higher delay between CS changes (i.e. when CS goes up, the spec recommends
that it be brought down after a minimum of 16 uS).
Other ADIS chips require (via spec) a minimum of 2 uS between CS changes.
The kernel's 10 uS default should be fine for those other chips; they
haven't been tested with lower CS change delays yet.
Datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/adis16460.pdf
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support to STM LSM6DS3-LSM6DSM 6-axis (acc + gyro) Mems sensor
http://www.st.com/resource/en/datasheet/lsm6ds3.pdf
http://www.st.com/resource/en/datasheet/lsm6dsm.pdf
- continuous mode support
- i2c support
- spi support
- sw fifo mode support
- supported devices: lsm6ds3, lsm6dsm
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
BMI160 is an Inertial Measurement Unit (IMU) which provides acceleration
and angular rate measurement. It also offers a secondary I2C interface
for connecting a magnetometer sensor (usually BMM160).
Current driver offers support for accelerometer and gyroscope readings
via sysfs or via buffer interface using an external trigger (e.g.
hrtimer). Data is retrieved from IMU via I2C or SPI interface.
Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMI160-DS000-07-786474.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This creates a data ready trigger per IIO device.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.
This driver uses two IIO devices one for accelerometer and one for magnetometer.
Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The two halves of this part can run largely independently. Hence
a version 4 of this patch followed that reorganized things completely.
This reverts commit d7d787d29148cde12958c2e3765ad3a55dc55eaf.
|
|
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.
Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.
Also reorder those entries which weren't in alphabetical order yet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This the basic functional Invensense MPU6050 Device driver.
Signed-off-by: Ge Gao <ggao@invensense.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adis16400 driver is in pretty good shape now, so move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds support for the ADIS16375, ADIS16480, ADIS16485, ADIS16488 6
degree to 10 degree of freedom IMUs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Now that the adis library no longer depends on the sw_ring buffer implementation
we can move it out of staging.
While we are at it also sort the entries in the iio Kconfig and Makefile to be
in alphabetical order.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
