| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The QAT driver allows enabling SR-IOV VFs but does not allow them to be
disabled through a write to sysfs.
Disabling SR-IOV VFs can be only achieved by bringing down and up a
device using the attribute /sys/bus/pci/devices/<BDF>/qat/state.
The documentation for the sysfs attribute `sriov_numvfs` specifies
that "a userspace application wanting to disable the VFs would write a
zero to this file".
Add support for disabling SR-IOV VFs by writing '0' to the
'sriov_numvfs' attribute in sysfs.
Enabling or disabling SR-IOV always requires adf_dev_down() to be
called. This action subsequently leads to the deletion of the
ADF_KERNEL_SEC configuration section. The keys ADF_NUM_CY and ADF_NUM_DC
within that section must be set to '0', otherwise, the driver will
register into the Linux Crypto Framework. Because of this, the
configuration in the ADF_KERNEL_SEC section must be added before every
sriov_enable.
Signed-off-by: Michal Witwicki <michal.witwicki@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The ADF_GENERAL_SEC configuration section contains values that must be
preserved during state transitions (down -> up, up -> down).
This patch modifies the logic in adf_dev_shutdown() to maintain all
key values within this section, rather than selectively saving and
restoring only the ADF_SERVICES_ENABLED attribute.
To achieve this, a new function has been introduced that deletes all
configuration sections except for the one specified by name.
This function is invoked during adf_dev_down(), with ADF_GENERAL_SEC
as the argument. Consequently, the adf_dev_shutdown_cache_cfg() function
has been removed as it is now redundant.
Additionally, this patch eliminates the cache_config parameter from
the adf_dev_down() function since ADF_GENERAL_SEC should always be
retained. This change does not cause any side effects because all
entries in the key-value store are cleared when a module is unloaded.
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Co-developed-by: Michal Witwicki <michal.witwicki@intel.com>
Signed-off-by: Michal Witwicki <michal.witwicki@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add logic to implement the interface for live migration defined in
qat/qat_mig_dev.h. This is specific for QAT GEN4 Virtual Functions
(VFs).
This introduces a migration data manager which is used to handle the
device state during migration. The manager ensures that the device state
is stored in a format that can be restored in the destination node.
The VF state is organized into a hierarchical structure that includes a
preamble, a general state section, a MISC bar section and an ETR bar
section. The latter contains the state of the 4 ring pairs contained on
a VF. Here is a graphical representation of the state:
preamble | general state section | leaf state
| MISC bar state section| leaf state
| ETR bar state section | bank0 state section | leaf state
| bank1 state section | leaf state
| bank2 state section | leaf state
| bank3 state section | leaf state
In addition to the implementation of the qat_migdev_ops interface and
the state manager framework, add a mutex in pfvf to avoid pf2vf messages
during migration.
Signed-off-by: Xin Zeng <xin.zeng@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When a Physical Function (PF) is reset, SR-IOV gets disabled, making the
associated Virtual Functions (VFs) unavailable. Even after reset and
using pci_restore_state, VFs remain uncreated because the numvfs still
at 0. Therefore, it's necessary to reconfigure SR-IOV to re-enable VFs.
This commit introduces the ADF_SRIOV_ENABLED configuration flag to cache
the SR-IOV enablement state. SR-IOV is only re-enabled if it was
previously configured.
This commit also introduces a dedicated workqueue without
`WQ_MEM_RECLAIM` flag for enabling SR-IOV during Heartbeat and CPM error
resets, preventing workqueue flushing warning.
This patch is based on earlier work done by Shashank Gupta.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Update the PFVF logic to handle restart and recovery. This adds the
following functions:
* adf_pf2vf_notify_fatal_error(): allows the PF to notify VFs that the
device detected a fatal error and requires a reset. This sends to
VF the event `ADF_PF2VF_MSGTYPE_FATAL_ERROR`.
* adf_pf2vf_wait_for_restarting_complete(): allows the PF to wait for
`ADF_VF2PF_MSGTYPE_RESTARTING_COMPLETE` events from active VFs
before proceeding with a reset.
* adf_pf2vf_notify_restarted(): enables the PF to notify VFs with
an `ADF_PF2VF_MSGTYPE_RESTARTED` event after recovery, indicating that
the device is back to normal. This prompts VF drivers switch back to
use the accelerator for workload processing.
These changes improve the communication and synchronization between PF
and VF drivers during system restart and recovery processes.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
With the growing number of Intel crypto drivers, it makes sense to
group them all into a single drivers/crypto/intel/ directory.
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
