| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The assigned clock for JPEG encoder IP has to be IMX95_CLK_VPUBLK_JPEG_ENC
and not IMX95_CLK_VPUBLK_JPEG_DEC (_ENC at the end, not _DEC). This is a
simple copy-paste error, fix it.
Fixes: 153c039a7357 ("arm64: dts: imx95: add jpeg encode and decode nodes")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
1, the phy support up to 8Mbit/s databitrate for CAN FD.
refer to product data sheet:
https://www.nxp.com/docs/en/data-sheet/TJA1463.pdf
2, the standby pin of the phy is ACTIVE_LOW.
3, the phy of flexcan2 connect the standby/en pin to PCAL6408 on i2c4 bus.
Fixes: 02b7adb791e1 ("arm64: dts: imx95-19x19-evk: add adc0 flexcan[1,2] i2c[2,3] uart5 spi3 and tpm3")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
eDM SBC
Add missing microSD slot vqmmc-supply property, otherwise the kernel
might shut down LDO5 regulator and that would power off the microSD
card slot, possibly while it is in use. Add the property to make sure
the kernel is aware of the LDO5 regulator which supplies the microSD
slot and keeps the LDO5 enabled.
Fixes: 562d222f23f0 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Plus DHCOM
Add missing microSD slot vqmmc-supply property, otherwise the kernel
might shut down LDO5 regulator and that would power off the microSD
card slot, possibly while it is in use. Add the property to make sure
the kernel is aware of the LDO5 regulator which supplies the microSD
slot and keeps the LDO5 enabled.
Fixes: 8d6712695bc8 ("arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
BUCK4 rail supplies the 3.3V rail. Use the actual regulator
instead of a virtual fixed regulator.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix SD card removal caused by automatic LDO5 power off after boot:
LDO5: disabling
mmc1: card 59b4 removed
EXT4-fs (mmcblk1p2): shut down requested (2)
Aborting journal on device mmcblk1p2-8.
JBD2: I/O error when updating journal superblock for mmcblk1p2-8.
To prevent this, add vqmmc regulator for USDHC, using a GPIO-controlled
regulator that is supplied by LDO5. Since this is implemented on SoM but
used on baseboards with SD-card interface, implement the functionality
on SoM part and optionally enable it on baseboards if needed.
Fixes: 418d1d840e42 ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There are a few new variants of existing chips:
- mt6572 is an older mobile phone chip from mediatek that was
extremely popular a decade ago but never got upstreamed until now
- exynos2200 is a recent high-end mobile phone chip used in a few
Samsung phones like the Galaxy S22
- Renesas R-Car V4M-7 (R8A779H2) is an updated version of R-Car V4M
(R8A779H0) and used in automotive applications
- Tegra264 is a new chip from NVIDIA, but support is fairly minimal
for now, and not much information is public about it
There are five more chips in a separate branch, as those are new chip
families that I merged along with the necessary infrastructure.
New board support is not that exciting, with a total of 33 newly added
machines here:
- Evaluation platforms for the chips above, plus TI am62d2 and Sophgo
sg2042
- Six 32-bit industrial boards based on stm32, imx6 and am33 chips,
plus eight 64-bit rockchips rk33xx/rk35xx, am62d2, t527, imx8 and
imx95
- Two newly added ASPEED BMC based motherboards, and one that got
removed
- Phones and Tablets based on 32-bit mt6572, tegra30 and 64-bit
msm8976 SoCs
- Three Laptops based on Mediatek mt8186 and Qualcomm Snapdragon X1
- A set-top box based on Amlogic meson-gxm
Updates for existing machines are spread over all the above families.
One notable change here is support for the RP1 I/O chip used in
Raspberry Pi 5"
* tag 'soc-dt-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (606 commits)
riscv: dts: sophgo: fix mdio node name for CV180X
riscv: dts: sophgo: sophgo-srd3-10: reserve uart0 device
riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree
riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree
dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings
riscv: dts: sophgo: add ethernet GMAC device for sg2042
riscv: dts: sophgo: Enable ethernet device for Huashan Pi
riscv: dts: sophgo: Add mdio multiplexer device for cv18xx
riscv: dts: sophgo: Add ethernet device for cv18xx
riscv: dts: sophgo: sg2044: add pmu configuration
riscv: dts: sophgo: sg2044: add ziccrse extension
riscv: dts: sophgo: add zfh for sg2042
riscv: dts: sophgo: add ziccrse for sg2042
riscv: dts: sophgo: Add xtheadvector to the sg2042 devicetree
riscv: dts: sophgo: sg2044: add PCIe device support for SG2044
riscv: dts: sophgo: sg2044: add MSI device support for SG2044
riscv: dts: sophgo: add reset configuration for Sophgo CV1800 series SoC
riscv: dts: sophgo: add reset generator for Sophgo CV1800 series SoC
dt-bindings: soc: sophgo: Move SoCs/boards from riscv into soc, add SG2000
riscv: dts: sophgo: sg2044: Add missing riscv,cbop-block-size property
...
|
|
We need the USB/Thunderbolt fixes in here for other patches to be on top
of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add ov5640 overlay file for imx8qm-mek and imx8qxp-mek board. Camera can
connect different CSI port. So use dts overlay file to handle these
difference connect options.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the gpio hog node which forces using DSI signals rather than
the second LVDS channels signals.
The dsi signals are not used in any of the current device trees.
Leave that decision to the actual device tree which will also define
the consumer of the signals.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The MUX which either outputs DSI or 2nd channel LVDS signals is part of
the SoM. Move the pinmuxing of the GPIO used for controlling the MUX
to the SoM dtsi file.
Fixes: 97dc91c04558 ("arm64: dts: freescale: add Toradex SMARC iMX8MP")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8M reference manuals indicate in the USDHC Clock generator section
that the clock rate for DDR is 1/2 the input clock therefore HS400 rates
clocked at 200Mhz require a 400Mhz SDHC clock.
This showed about a 1.5x improvement in read performance for the eMMC's
used on the various imx8m{m,n,p}-venice boards.
Fixes: b999bdaf0597 ("arm64: dts: imx: Add i.mx8mm Gateworks gw7904 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8M reference manuals indicate in the USDHC Clock generator section
that the clock rate for DDR is 1/2 the input clock therefore HS400 rates
clocked at 200Mhz require a 400Mhz SDHC clock.
This showed about a 1.5x improvement in read performance for the eMMC's
used on the various imx8m{m,n,p}-venice boards.
Fixes: a72ba91e5bc7 ("arm64: dts: imx: Add i.mx8mm Gateworks gw7903 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8M reference manuals indicate in the USDHC Clock generator section
that the clock rate for DDR is 1/2 the input clock therefore HS400 rates
clocked at 200Mhz require a 400Mhz SDHC clock.
This showed about a 1.5x improvement in read performance for the eMMC's
used on the various imx8m{m,n,p}-venice boards.
Fixes: ef484dfcf6f7 ("arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8M reference manuals indicate in the USDHC Clock generator section
that the clock rate for DDR is 1/2 the input clock therefore HS400 rates
clocked at 200Mhz require a 400Mhz SDHC clock.
This showed about a 1.5x improvement in read performance for the eMMC's
used on the various imx8m{m,n,p}-venice boards.
Fixes: ef484dfcf6f7 ("arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8M reference manuals indicate in the USDHC Clock generator section
that the clock rate for DDR is 1/2 the input clock therefore HS400 rates
clocked at 200Mhz require a 400Mhz SDHC clock.
This showed about a 1.5x improvement in read performance for the eMMC's
used on the various imx8m{m,n,p}-venice boards.
Fixes: 2b1649a83afc ("arm64: dts: imx: Add i.mx8mm Gateworks gw7901 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://lore.kernel.org/stable/20250707201702.2930066-3-tharvey%40gateworks.com
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8M reference manuals indicate in the USDHC Clock generator section
that the clock rate for DDR is 1/2 the input clock therefore HS400 rates
clocked at 200Mhz require a 400Mhz SDHC clock.
This showed about a 1.5x improvement in read performance for the eMMC's
used on the various imx8mp-venice boards.
Fixes: 0d5b288c2110 ("arm64: dts: freescale: Add imx8mp-venice-gw7905-2x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8M reference manuals indicate in the USDHC Clock generator section
that the clock rate for DDR is 1/2 the input clock therefore HS400 rates
clocked at 200Mhz require a 400Mhz SDHC clock.
This showed about a 1.5x improvement in read performance for the eMMC's
used on the various imx8m{m,n,p}-venice boards.
Fixes: 6f30b27c5ef5 ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Describe the two LX2160AQDS on-board RGMII PHYs on their respective MDIO
buses behind the MDIO multiplexer.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device tree for the Libra-i.MX 95 FPSC board. The Libra is a
pure development board and has hardware to support FPSC-24-A.0 set of
features. The phyCORE-i.MX 95 FPSC [1] SoM uses only a subset of
the hardware features of the Libra board. The phyCORE-i.MX 95 FPSC
itself is a System on Module designed around the i.MX 95 SoC.
The SoM and board utilize the Future Proof Solder Core [2] BGA standard
to connect to each other.
To be able to easily map FPSC interface names to SoC interfaces, the
FPSC interface names are added as inline comments. Example:
&lpi2c5 { /* I2C2 */
pinctrl-0 = <&pinctrl_lpi2c5>;
[...]
};
Here, I2C2 is the FPSC interface name. The lpi2c5 instance of the i.MX 95
SoC is used to fulfill the i2c functionality and its signals are routed
to the FPSC I2C2 signal pins:
pinctrl_lpi2c5: lpi2c5grp {
fsl,pins = <
IMX95_PAD_GPIO_IO22__LPI2C5_SDA 0x40000b9e /* I2C2_SDA */
IMX95_PAD_GPIO_IO23__LPI2C5_SCL 0x40000b9e /* I2C2_SCL */
>;
};
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-95-fpsc/
[2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc/
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add linux,cma node because some devices, such as camera, need big continue
physical memory.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add CSI related nodes (i2c, irqsteer, csi, lpcg) for i.MX8 img subsystem.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add jpeg encode\decode and related nodes for i.MX95.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add overlay to support PHYTEC PEB-WLBT-07 WiFi/Bluetooth evaluation
adapter on phyBOARD-Nash-i.MX93 board. Adapter uses the u-blox MAYA-W2
module (IW612 chipset) which is capable of Wi-Fi 6 and Bluetooth 5.4 LE.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for PEB-WLBT-05 WLAN/BT adapter on phyBOARD-Segin-i.MX93.
The PEB-WLBT-05 is equipped with a Sterling-LWB radio module, which is
capable of Wi-Fi 802.11 b/g/n and Bluetooth 4.2.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add overlay to support PEB-EVAL-01 adapter on phyBOARD-Segin-i.MX93.
This is a PHYTEC evaluation module with three LEDs and two input buttons
that users can attach to the board expansion connector X16.
Note that, due to compatibility with existing PHYTEC platforms using the
phyBOARD-Segin carrier board such as i.MX6UL and STM32MP1, we face some
hardware limitations and can thus only support one user LED (D2) and one
button (S2) on the i.MX93 variant of the phyBOARD-Segin.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an overlay used for remote processor inter-core communication
between A55 and M33 cores on the phyCORE-i.MX93 SoM based boards.
Overlay adds the required reserved memory regions and enables the
mailbox unit and the M33 core for RPMsg (Remote Processor Messaging
Framework).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The I²C mux controller is supplied by 3.3V rail. Add the corresponding
supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are two SFP interfaces usable on TQMLS1046A. Enable all the
corresponding nodes. U-Boot will configure the connection if the RCW
is configured accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is an SFP interface usable on TQMLS1043A. Enable all the
corresponding nodes. U-Boot will configure the connection if the RCW
is configured accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SFP is placed on mainboard, available to TQMLS1043A/1046A/1088A.
Provide it in a common place, disabled by default.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The jedec SPI-NOR flash node itself has no partitions, but the partitions
subnode.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The jedec SPI-NOR flash node itself has no partitions, but the partitions
subnode.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The jedec SPI-NOR flash node itself has no partitions, but the partitions
subnode.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing clocks and clock-names properties for flexcan1 in
imx94.dtsi to align with other FlexCAN instances.
Fixes: b0d011d4841b ("arm64: dts: freescale: Add basic dtsi for imx943")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
UART2 is often used as the console, so the DMA was likely left
off on purpose, since it's recommended to not use the DMA on the
console. Because, the driver checks to see if the UART is used for
the console when determining if it should initialize DMA, it
should be safe to enable DMA on UART2 for all users.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
UART2 is often used as the console, so the DMA was likely left
off on purpose, since it's recommended to not use the DMA on the
console. Because, the driver checks to see if the UART is used for
the console when determining if it should initialize DMA, it
should be safe to enable DMA on UART2 for all users.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Only i2c0 had it's DMA channels configured. Add the missing one.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Only i2c0 had it's DMA channels configured. Add the missing one.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On phyCORE-i.MX93 SoM, the SoC WDOG_ANY output line is connected to the
external pca9451a PMIC WDOG_B input. Apply pinctrl and set the property
"fsl,ext-reset-output" for watchdog to trigger board reset via PMIC on
timeout/reset.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reference manual for the i.MX8MN states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reference manual for the i.MX8MM states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This platform supports several displays, so rename the overlay to reflect
the actual display being used. This also aligns the name to the other
TQMa8M* modules. Apply the same change for MBa8MP-RAS314 as well, as it
uses the same overlay.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8QM MEK RevD board is a reworked version of the i.MX8QM MEK
board, which includes some sensor and component changes. One of these
components is the WM8962 codec, which is meant to replace the WM8960
codec present on i.MX8QM MEK. To avoid having to introduce a devicetree
overlay or another DTS, the WM8962 can be supported by using a virtual
I2C MUX since both of the codecs share the same I2C address.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8QXP WCPU MEK board is a reworked version of the i.MX8QXP MEK
board, which includes some sensor and component changes. One of these
components is the WM8962 codec, which is meant to replace the WM8960
codec present on i.MX8QXP MEK. To avoid having to introduce a devicetree
overlay or another DTS, the WM8962 can be supported by using a virtual
I2C MUX since both of the codecs share the same I2C address.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In order to support Asynchronous Sample Rate Converter (ASRC), switch to
fsl-asoc-card driver for the wm8960 sound card.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add edma error irq for imx93.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Alberto Merciai <alb3rt0.m3rciai@gmail.com>
Tested-by: Alberto Merciai <alb3rt0.m3rciai@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The fan controller on this board cannot work in automatic mode, and
requires software control, the reason is that it has no temperature
sensor connected.
Given that this board is a development kit and does not have any
specific fan, add a default single cooling level that would enable the
fan to spin with a 100% duty cycle, enabling a safe default.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The defaults for this SoC are configured for overdrive mode, but
the VPU clocks are currently configured for nominal mode.
Increase VPU_G1_CLK_ROOT to 800MHZ from 600MHz,
Increase VPU_G2_CLK_ROOT to 700MHZ from 500MHz, and
Increase VPU_BUS_CLK_ROOT to 800MHz from 600MHz.
This requires adjusting the clock parents. Since there is already
800MHz clock references, move the VPU_BUS and G1 clocks to it.
This frees up the VPU_PLL to be configured at 700MHz to run
the G2 clock at 700MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
