diff options
Diffstat (limited to 'include/uapi/linux/nl80211.h')
-rw-r--r-- | include/uapi/linux/nl80211.h | 90 |
1 files changed, 89 insertions, 1 deletions
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index e23d78685a01..220694151434 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -493,7 +493,12 @@ * This attribute is ignored if driver does not support roam scan. * It is also sent as an event, with the BSSID and response IEs when the * connection is established or failed to be established. This can be - * determined by the STATUS_CODE attribute. + * determined by the %NL80211_ATTR_STATUS_CODE attribute (0 = success, + * non-zero = failure). If %NL80211_ATTR_TIMED_OUT is included in the + * event, the connection attempt failed due to not being able to initiate + * authentication/association or not receiving a response from the AP. + * Non-zero %NL80211_ATTR_STATUS_CODE value is indicated in that case as + * well to remain backwards compatible. * @NL80211_CMD_ROAM: request that the card roam (currently not implemented), * sent as an event when the card/driver roamed by itself. * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify @@ -1819,6 +1824,49 @@ enum nl80211_commands { * * @NL80211_ATTR_PAD: attribute used for padding for 64-bit alignment * + * @NL80211_ATTR_IFTYPE_EXT_CAPA: Nested attribute of the following attributes: + * %NL80211_ATTR_IFTYPE, %NL80211_ATTR_EXT_CAPA, + * %NL80211_ATTR_EXT_CAPA_MASK, to specify the extended capabilities per + * interface type. + * + * @NL80211_ATTR_MU_MIMO_GROUP_DATA: array of 24 bytes that defines a MU-MIMO + * groupID for monitor mode. + * The first 8 bytes are a mask that defines the membership in each + * group (there are 64 groups, group 0 and 63 are reserved), + * each bit represents a group and set to 1 for being a member in + * that group and 0 for not being a member. + * The remaining 16 bytes define the position in each group: 2 bits for + * each group. + * (smaller group numbers represented on most significant bits and bigger + * group numbers on least significant bits.) + * This attribute is used only if all interfaces are in monitor mode. + * Set this attribute in order to monitor packets using the given MU-MIMO + * groupID data. + * to turn off that feature set all the bits of the groupID to zero. + * @NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR: mac address for the sniffer to follow + * when using MU-MIMO air sniffer. + * to turn that feature off set an invalid mac address + * (e.g. FF:FF:FF:FF:FF:FF) + * + * @NL80211_ATTR_SCAN_START_TIME_TSF: The time at which the scan was actually + * started (u64). The time is the TSF of the BSS the interface that + * requested the scan is connected to (if available, otherwise this + * attribute must not be included). + * @NL80211_ATTR_SCAN_START_TIME_TSF_BSSID: The BSS according to which + * %NL80211_ATTR_SCAN_START_TIME_TSF is set. + * @NL80211_ATTR_MEASUREMENT_DURATION: measurement duration in TUs (u16). If + * %NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY is not set, this is the + * maximum measurement duration allowed. This attribute is used with + * measurement requests. It can also be used with %NL80211_CMD_TRIGGER_SCAN + * if the scan is used for beacon report radio measurement. + * @NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY: flag attribute that indicates + * that the duration specified with %NL80211_ATTR_MEASUREMENT_DURATION is + * mandatory. If this flag is not set, the duration is the maximum duration + * and the actual measurement duration may be shorter. + * + * @NL80211_ATTR_MESH_PEER_AID: Association ID for the mesh peer (u16). This is + * used to pull the stored data for mesh peer in power save state. + * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -2201,6 +2249,18 @@ enum nl80211_attrs { NL80211_ATTR_PAD, + NL80211_ATTR_IFTYPE_EXT_CAPA, + + NL80211_ATTR_MU_MIMO_GROUP_DATA, + NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR, + + NL80211_ATTR_SCAN_START_TIME_TSF, + NL80211_ATTR_SCAN_START_TIME_TSF_BSSID, + NL80211_ATTR_MEASUREMENT_DURATION, + NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY, + + NL80211_ATTR_MESH_PEER_AID, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -3462,6 +3522,12 @@ enum nl80211_bss_scan_width { * was last updated by a received frame. The value is expected to be * accurate to about 10ms. (u64, nanoseconds) * @NL80211_BSS_PAD: attribute used for padding for 64-bit alignment + * @NL80211_BSS_PARENT_TSF: the time at the start of reception of the first + * octet of the timestamp field of the last beacon/probe received for + * this BSS. The time is the TSF of the BSS specified by + * @NL80211_BSS_PARENT_BSSID. (u64). + * @NL80211_BSS_PARENT_BSSID: the BSS according to which @NL80211_BSS_PARENT_TSF + * is set. * @__NL80211_BSS_AFTER_LAST: internal * @NL80211_BSS_MAX: highest BSS attribute */ @@ -3483,6 +3549,8 @@ enum nl80211_bss { NL80211_BSS_PRESP_DATA, NL80211_BSS_LAST_SEEN_BOOTTIME, NL80211_BSS_PAD, + NL80211_BSS_PARENT_TSF, + NL80211_BSS_PARENT_BSSID, /* keep last */ __NL80211_BSS_AFTER_LAST, @@ -4467,6 +4535,22 @@ enum nl80211_feature_flags { * %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set * the ASSOC_REQ_USE_RRM flag in the association request even if * NL80211_FEATURE_QUIET is not advertized. + * @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air + * sniffer which means that it can be configured to hear packets from + * certain groups which can be configured by the + * %NL80211_ATTR_MU_MIMO_GROUP_DATA attribute, + * or can be configured to follow a station by configuring the + * %NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR attribute. + * @NL80211_EXT_FEATURE_SCAN_START_TIME: This driver includes the actual + * time the scan started in scan results event. The time is the TSF of + * the BSS that the interface that requested the scan is connected to + * (if available). + * @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the + * time the last beacon/probe was received. The time is the TSF of the + * BSS that the interface that requested the scan is connected to + * (if available). + * @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of + * channel dwell time. * * @NUM_NL80211_EXT_FEATURES: number of extended features. * @MAX_NL80211_EXT_FEATURES: highest extended feature index. @@ -4474,6 +4558,10 @@ enum nl80211_feature_flags { enum nl80211_ext_feature_index { NL80211_EXT_FEATURE_VHT_IBSS, NL80211_EXT_FEATURE_RRM, + NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER, + NL80211_EXT_FEATURE_SCAN_START_TIME, + NL80211_EXT_FEATURE_BSS_PARENT_TSF, + NL80211_EXT_FEATURE_SET_SCAN_DWELL, /* add new features before the definition below */ NUM_NL80211_EXT_FEATURES, |