diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 22 |
1 files changed, 18 insertions, 4 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index c90047de4428..74ccf30fdf8e 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -186,7 +186,8 @@ enum ieee80211_bss_change { * @use_short_slot: use short slot time (only relevant for ERP); * if the hardware cannot handle this it must set the * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag - * @dtim_period: num of beacons before the next DTIM, for PSM + * @dtim_period: num of beacons before the next DTIM, for beaconing, + * not valid in station mode (cf. hw conf ps_dtim_period) * @timestamp: beacon timestamp * @beacon_int: beacon interval * @assoc_capability: capabilities taken from assoc resp @@ -271,6 +272,11 @@ struct ieee80211_bss_conf { * transmit function after the current frame, this can be used * by drivers to kick the DMA queue only if unset or when the * queue gets full. + * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted + * after TX status because the destination was asleep, it must not + * be modified again (no seqno assignment, crypto, etc.) + * @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still + * has a radiotap header at skb->data. */ enum mac80211_tx_control_flags { IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), @@ -291,6 +297,8 @@ enum mac80211_tx_control_flags { IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16), IEEE80211_TX_CTL_PSPOLL_RESPONSE = BIT(17), IEEE80211_TX_CTL_MORE_FRAMES = BIT(18), + IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19), + IEEE80211_TX_INTFL_HAS_RADIOTAP = BIT(20), }; /** @@ -644,6 +652,9 @@ enum ieee80211_smps_mode { * value will be only achievable between DTIM frames, the hardware * needs to check for the multicast traffic bit in DTIM beacons. * This variable is valid only when the CONF_PS flag is set. + * @ps_dtim_period: The DTIM period of the AP we're connected to, for use + * in power saving. Power saving will not be enabled until a beacon + * has been received and the DTIM period is known. * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the * powersave documentation below. This variable is valid only when * the CONF_PS flag is set. @@ -670,6 +681,7 @@ struct ieee80211_conf { int max_sleep_period; u16 listen_interval; + u8 ps_dtim_period; u8 long_frame_max_tx_count, short_frame_max_tx_count; @@ -1485,7 +1497,7 @@ enum ieee80211_ampdu_mlme_action { * @update_tkip_key: See the section "Hardware crypto acceleration" * This callback will be called in the context of Rx. Called for drivers * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY. - * The callback can sleep. + * The callback must be atomic. * * @hw_scan: Ask the hardware to service the scan request, no need to start * the scan state machine in stack. The scan must honour the channel @@ -1610,8 +1622,10 @@ struct ieee80211_ops { struct ieee80211_vif *vif, struct ieee80211_sta *sta, struct ieee80211_key_conf *key); void (*update_tkip_key)(struct ieee80211_hw *hw, - struct ieee80211_key_conf *conf, const u8 *address, - u32 iv32, u16 *phase1key); + struct ieee80211_vif *vif, + struct ieee80211_key_conf *conf, + struct ieee80211_sta *sta, + u32 iv32, u16 *phase1key); int (*hw_scan)(struct ieee80211_hw *hw, struct cfg80211_scan_request *req); void (*sw_scan_start)(struct ieee80211_hw *hw); |