diff options
Diffstat (limited to 'drivers/net/phy/bcm7xxx.c')
| -rw-r--r-- | drivers/net/phy/bcm7xxx.c | 359 |
1 files changed, 359 insertions, 0 deletions
diff --git a/drivers/net/phy/bcm7xxx.c b/drivers/net/phy/bcm7xxx.c new file mode 100644 index 000000000000..526b94cea569 --- /dev/null +++ b/drivers/net/phy/bcm7xxx.c @@ -0,0 +1,359 @@ +/* + * Broadcom BCM7xxx internal transceivers support. + * + * Copyright (C) 2014, Broadcom Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/module.h> +#include <linux/phy.h> +#include <linux/delay.h> +#include <linux/bitops.h> +#include <linux/brcmphy.h> + +/* Broadcom BCM7xxx internal PHY registers */ +#define MII_BCM7XXX_CHANNEL_WIDTH 0x2000 + +/* 40nm only register definitions */ +#define MII_BCM7XXX_100TX_AUX_CTL 0x10 +#define MII_BCM7XXX_100TX_FALSE_CAR 0x13 +#define MII_BCM7XXX_100TX_DISC 0x14 +#define MII_BCM7XXX_AUX_MODE 0x1d +#define MII_BCM7XX_64CLK_MDIO BIT(12) +#define MII_BCM7XXX_CORE_BASE1E 0x1e +#define MII_BCM7XXX_TEST 0x1f +#define MII_BCM7XXX_SHD_MODE_2 BIT(2) + +/* 28nm only register definitions */ +#define MISC_ADDR(base, channel) base, channel + +#define DSP_TAP10 MISC_ADDR(0x0a, 0) +#define PLL_PLLCTRL_1 MISC_ADDR(0x32, 1) +#define PLL_PLLCTRL_2 MISC_ADDR(0x32, 2) +#define PLL_PLLCTRL_4 MISC_ADDR(0x33, 0) + +#define AFE_RXCONFIG_0 MISC_ADDR(0x38, 0) +#define AFE_RXCONFIG_1 MISC_ADDR(0x38, 1) +#define AFE_RX_LP_COUNTER MISC_ADDR(0x38, 3) +#define AFE_TX_CONFIG MISC_ADDR(0x39, 0) +#define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0) + +#define CORE_EXPB0 0xb0 + +static int bcm7445_config_init(struct phy_device *phydev) +{ + int ret; + const struct bcm7445_regs { + int reg; + u16 value; + } bcm7445_regs_cfg[] = { + /* increases ADC latency by 24ns */ + { MII_BCM54XX_EXP_SEL, 0x0038 }, + { MII_BCM54XX_EXP_DATA, 0xAB95 }, + /* increases internal 1V LDO voltage by 5% */ + { MII_BCM54XX_EXP_SEL, 0x2038 }, + { MII_BCM54XX_EXP_DATA, 0xBB22 }, + /* reduce RX low pass filter corner frequency */ + { MII_BCM54XX_EXP_SEL, 0x6038 }, + { MII_BCM54XX_EXP_DATA, 0xFFC5 }, + /* reduce RX high pass filter corner frequency */ + { MII_BCM54XX_EXP_SEL, 0x003a }, + { MII_BCM54XX_EXP_DATA, 0x2002 }, + }; + unsigned int i; + + for (i = 0; i < ARRAY_SIZE(bcm7445_regs_cfg); i++) { + ret = phy_write(phydev, + bcm7445_regs_cfg[i].reg, + bcm7445_regs_cfg[i].value); + if (ret) + return ret; + } + + return 0; +} + +static void phy_write_exp(struct phy_device *phydev, + u16 reg, u16 value) +{ + phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER | reg); + phy_write(phydev, MII_BCM54XX_EXP_DATA, value); +} + +static void phy_write_misc(struct phy_device *phydev, + u16 reg, u16 chl, u16 value) +{ + int tmp; + + phy_write(phydev, MII_BCM54XX_AUX_CTL, MII_BCM54XX_AUXCTL_SHDWSEL_MISC); + + tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL); + tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA; + phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp); + + tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) | reg; + phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp); + + phy_write(phydev, MII_BCM54XX_EXP_DATA, value); +} + +static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev) +{ + /* Increase VCO range to prevent unlocking problem of PLL at low + * temp + */ + phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048); + + /* Change Ki to 011 */ + phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b); + + /* Disable loading of TVCO buffer to bandgap, set bandgap trim + * to 111 + */ + phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20); + + /* Adjust bias current trim by -3 */ + phy_write_misc(phydev, DSP_TAP10, 0x690b); + + /* Switch to CORE_BASE1E */ + phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd); + + /* Reset R_CAL/RC_CAL Engine */ + phy_write_exp(phydev, CORE_EXPB0, 0x0010); + + /* Disable Reset R_CAL/RC_CAL Engine */ + phy_write_exp(phydev, CORE_EXPB0, 0x0000); + + /* write AFE_RXCONFIG_0 */ + phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19); + + /* write AFE_RXCONFIG_1 */ + phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f); + + /* write AFE_RX_LP_COUNTER */ + phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); + + /* write AFE_HPF_TRIM_OTHERS */ + phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b); + + /* write AFTE_TX_CONFIG */ + phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800); + + return 0; +} + +static int bcm7xxx_28nm_config_init(struct phy_device *phydev) +{ + int ret; + + ret = bcm7445_config_init(phydev); + if (ret) + return ret; + + return bcm7xxx_28nm_afe_config_init(phydev); +} + +static int phy_set_clr_bits(struct phy_device *dev, int location, + int set_mask, int clr_mask) +{ + int v, ret; + + v = phy_read(dev, location); + if (v < 0) + return v; + + v &= ~clr_mask; + v |= set_mask; + + ret = phy_write(dev, location, v); + if (ret < 0) + return ret; + + return v; +} + +static int bcm7xxx_config_init(struct phy_device *phydev) +{ + int ret; + + /* Enable 64 clock MDIO */ + phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XX_64CLK_MDIO); + phy_read(phydev, MII_BCM7XXX_AUX_MODE); + + /* Workaround only required for 100Mbits/sec */ + if (!(phydev->dev_flags & PHY_BRCM_100MBPS_WAR)) + return 0; + + /* set shadow mode 2 */ + ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, + MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2); + if (ret < 0) + return ret; + + /* set iddq_clkbias */ + phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00); + udelay(10); + + /* reset iddq_clkbias */ + phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00); + + phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555); + + /* reset shadow mode 2 */ + ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, MII_BCM7XXX_SHD_MODE_2, 0); + if (ret < 0) + return ret; + + return 0; +} + +/* Workaround for putting the PHY in IDDQ mode, required + * for all BCM7XXX PHYs + */ +static int bcm7xxx_suspend(struct phy_device *phydev) +{ + int ret; + const struct bcm7xxx_regs { + int reg; + u16 value; + } bcm7xxx_suspend_cfg[] = { + { MII_BCM7XXX_TEST, 0x008b }, + { MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 }, + { MII_BCM7XXX_100TX_DISC, 0x7000 }, + { MII_BCM7XXX_TEST, 0x000f }, + { MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 }, + { MII_BCM7XXX_TEST, 0x000b }, + }; + unsigned int i; + + for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) { + ret = phy_write(phydev, + bcm7xxx_suspend_cfg[i].reg, + bcm7xxx_suspend_cfg[i].value); + if (ret) + return ret; + } + + return 0; +} + +static int bcm7xxx_dummy_config_init(struct phy_device *phydev) +{ + return 0; +} + +static struct phy_driver bcm7xxx_driver[] = { +{ + .phy_id = PHY_ID_BCM7366, + .phy_id_mask = 0xfffffff0, + .name = "Broadcom BCM7366", + .features = PHY_GBIT_FEATURES | + SUPPORTED_Pause | SUPPORTED_Asym_Pause, + .flags = PHY_IS_INTERNAL, + .config_init = bcm7xxx_28nm_afe_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .suspend = bcm7xxx_suspend, + .resume = bcm7xxx_28nm_afe_config_init, + .driver = { .owner = THIS_MODULE }, +}, { + .phy_id = PHY_ID_BCM7439, + .phy_id_mask = 0xfffffff0, + .name = "Broadcom BCM7439", + .features = PHY_GBIT_FEATURES | + SUPPORTED_Pause | SUPPORTED_Asym_Pause, + .flags = PHY_IS_INTERNAL, + .config_init = bcm7xxx_28nm_afe_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .suspend = bcm7xxx_suspend, + .resume = bcm7xxx_28nm_afe_config_init, + .driver = { .owner = THIS_MODULE }, +}, { + .phy_id = PHY_ID_BCM7445, + .phy_id_mask = 0xfffffff0, + .name = "Broadcom BCM7445", + .features = PHY_GBIT_FEATURES | + SUPPORTED_Pause | SUPPORTED_Asym_Pause, + .flags = PHY_IS_INTERNAL, + .config_init = bcm7xxx_28nm_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .suspend = bcm7xxx_suspend, + .resume = bcm7xxx_28nm_config_init, + .driver = { .owner = THIS_MODULE }, +}, { + .name = "Broadcom BCM7XXX 28nm", + .phy_id = PHY_ID_BCM7XXX_28, + .phy_id_mask = PHY_BCM_OUI_MASK, + .features = PHY_GBIT_FEATURES | + SUPPORTED_Pause | SUPPORTED_Asym_Pause, + .flags = PHY_IS_INTERNAL, + .config_init = bcm7xxx_28nm_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .suspend = bcm7xxx_suspend, + .resume = bcm7xxx_28nm_config_init, + .driver = { .owner = THIS_MODULE }, +}, { + .phy_id = PHY_BCM_OUI_4, + .phy_id_mask = 0xffff0000, + .name = "Broadcom BCM7XXX 40nm", + .features = PHY_GBIT_FEATURES | + SUPPORTED_Pause | SUPPORTED_Asym_Pause, + .flags = PHY_IS_INTERNAL, + .config_init = bcm7xxx_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .suspend = bcm7xxx_suspend, + .resume = bcm7xxx_config_init, + .driver = { .owner = THIS_MODULE }, +}, { + .phy_id = PHY_BCM_OUI_5, + .phy_id_mask = 0xffffff00, + .name = "Broadcom BCM7XXX 65nm", + .features = PHY_BASIC_FEATURES | + SUPPORTED_Pause | SUPPORTED_Asym_Pause, + .flags = PHY_IS_INTERNAL, + .config_init = bcm7xxx_dummy_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .suspend = bcm7xxx_suspend, + .resume = bcm7xxx_config_init, + .driver = { .owner = THIS_MODULE }, +} }; + +static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = { + { PHY_ID_BCM7366, 0xfffffff0, }, + { PHY_ID_BCM7439, 0xfffffff0, }, + { PHY_ID_BCM7445, 0xfffffff0, }, + { PHY_ID_BCM7XXX_28, 0xfffffc00 }, + { PHY_BCM_OUI_4, 0xffff0000 }, + { PHY_BCM_OUI_5, 0xffffff00 }, + { } +}; + +static int __init bcm7xxx_phy_init(void) +{ + return phy_drivers_register(bcm7xxx_driver, + ARRAY_SIZE(bcm7xxx_driver)); +} + +static void __exit bcm7xxx_phy_exit(void) +{ + phy_drivers_unregister(bcm7xxx_driver, + ARRAY_SIZE(bcm7xxx_driver)); +} + +module_init(bcm7xxx_phy_init); +module_exit(bcm7xxx_phy_exit); + +MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl); + +MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Broadcom Corporation"); |