diff options
Diffstat (limited to 'Documentation/devicetree')
8 files changed, 618 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt index d857b67fab72..4346ff2dd8e6 100644 --- a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt @@ -17,6 +17,9 @@ and generic pin config nodes. Supported configurations: - skew-delay is supported on the Ethernet pins +- drive-strength with 4, 8, 12 or 16 mA as argument is supported for + entire groups on the groups "idegrp", "gmii_gmac0_grp", "gmii_gmac1_grp" + and "pcigrp". Example: diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt index a81bbf37ed66..7ca4f6118d9a 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt @@ -4,7 +4,8 @@ Please refer to fsl,imx-pinctrl.txt in this directory for common binding part and usage. Required properties: -- compatible: "fsl,imx6ul-iomuxc" +- compatible: "fsl,imx6ul-iomuxc" for main IOMUX controller or + "fsl,imx6ull-iomuxc-snvs" for i.MX 6ULL's SNVS IOMUX controller. - fsl,pins: each entry consists of 6 integers and represents the mux and config setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val input_val> are specified using a PIN_FUNC_ID macro, which can be found in diff --git a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt new file mode 100644 index 000000000000..24a210e0c59a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt @@ -0,0 +1,39 @@ +Microsemi Ocelot pin controller Device Tree Bindings +---------------------------------------------------- + +Required properties: + - compatible : Should be "mscc,ocelot-pinctrl" + - reg : Address and length of the register set for the device + - gpio-controller : Indicates this device is a GPIO controller + - #gpio-cells : Must be 2. + The first cell is the pin number and the + second cell specifies GPIO flags, as defined in + <dt-bindings/gpio/gpio.h>. + - gpio-ranges : Range of pins managed by the GPIO controller. + + +The ocelot-pinctrl driver uses the generic pin multiplexing and generic pin +configuration documented in pinctrl-bindings.txt. + +The following generic properties are supported: + - function + - pins + +Example: + gpio: pinctrl@71070034 { + compatible = "mscc,ocelot-pinctrl"; + reg = <0x71070034 0x28>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&gpio 0 0 22>; + + uart_pins: uart-pins { + pins = "GPIO_6", "GPIO_7"; + function = "uart"; + }; + + uart2_pins: uart2-pins { + pins = "GPIO_12", "GPIO_13"; + function = "uart2"; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt new file mode 100644 index 000000000000..f18ed99f6e14 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt @@ -0,0 +1,351 @@ +== MediaTek MT7622 pinctrl controller == + +Required properties for the root node: + - compatible: Should be one of the following + "mediatek,mt7622-pinctrl" for MT7622 SoC + - reg: offset and length of the pinctrl space + + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be two. The first cell is the pin number and the + second is the GPIO flags. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +MT7622 pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, slew rate, etc. + +We support 2 types of configuration nodes. Those nodes can be either pinmux +nodes or pinconf nodes. Each configuration node can consist of multiple nodes +describing the pinmux and pinconf options. + +The name of each subnode doesn't matter as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +== pinmux nodes content == + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinmux subnode: + +Required properties are: + - groups: An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. + - function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +== pinconf nodes content == + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinconf subnode: + +Required properties are: + - pins: An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + - groups: An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. + +Optional properies are: + bias-disable, bias-pull, bias-pull-down, input-enable, + input-schmitt-enable, input-schmitt-disable, output-enable + output-low, output-high, drive-strength, slew-rate + + Valid arguments for 'slew-rate' are '0' for no slew rate controlled and '1' for + slower slew rate respectively. + Valid arguments for 'drive-strength', 4, 8, 12, or 16 in mA. + +The following specific properties as defined are valid to specify in a pinconf +subnode: + +Optional properties are: + - mediatek,tdsel: An integer describing the steps for output level shifter duty + cycle when asserted (high pulse width adjustment). Valid arguments are from 0 + to 15. + - mediatek,rdsel: An integer describing the steps for input level shifter duty + cycle when asserted (high pulse width adjustment). Valid arguments are from 0 + to 63. + +== Valid values for pins, function and groups on MT7622 == + +Valid values for pins are: +pins can be referenced via the pin names as the below table shown and the +related physical number is also put ahead of those names which helps cross +references to pins between groups to know whether pins assignment conflict +happens among devices try to acquire those available pins. + + Pin #: Valid values for pins + ----------------------------- + PIN 0: "GPIO_A" + PIN 1: "I2S1_IN" + PIN 2: "I2S1_OUT" + PIN 3: "I2S_BCLK" + PIN 4: "I2S_WS" + PIN 5: "I2S_MCLK" + PIN 6: "TXD0" + PIN 7: "RXD0" + PIN 8: "SPI_WP" + PIN 9: "SPI_HOLD" + PIN 10: "SPI_CLK" + PIN 11: "SPI_MOSI" + PIN 12: "SPI_MISO" + PIN 13: "SPI_CS" + PIN 14: "I2C_SDA" + PIN 15: "I2C_SCL" + PIN 16: "I2S2_IN" + PIN 17: "I2S3_IN" + PIN 18: "I2S4_IN" + PIN 19: "I2S2_OUT" + PIN 20: "I2S3_OUT" + PIN 21: "I2S4_OUT" + PIN 22: "GPIO_B" + PIN 23: "MDC" + PIN 24: "MDIO" + PIN 25: "G2_TXD0" + PIN 26: "G2_TXD1" + PIN 27: "G2_TXD2" + PIN 28: "G2_TXD3" + PIN 29: "G2_TXEN" + PIN 30: "G2_TXC" + PIN 31: "G2_RXD0" + PIN 32: "G2_RXD1" + PIN 33: "G2_RXD2" + PIN 34: "G2_RXD3" + PIN 35: "G2_RXDV" + PIN 36: "G2_RXC" + PIN 37: "NCEB" + PIN 38: "NWEB" + PIN 39: "NREB" + PIN 40: "NDL4" + PIN 41: "NDL5" + PIN 42: "NDL6" + PIN 43: "NDL7" + PIN 44: "NRB" + PIN 45: "NCLE" + PIN 46: "NALE" + PIN 47: "NDL0" + PIN 48: "NDL1" + PIN 49: "NDL2" + PIN 50: "NDL3" + PIN 51: "MDI_TP_P0" + PIN 52: "MDI_TN_P0" + PIN 53: "MDI_RP_P0" + PIN 54: "MDI_RN_P0" + PIN 55: "MDI_TP_P1" + PIN 56: "MDI_TN_P1" + PIN 57: "MDI_RP_P1" + PIN 58: "MDI_RN_P1" + PIN 59: "MDI_RP_P2" + PIN 60: "MDI_RN_P2" + PIN 61: "MDI_TP_P2" + PIN 62: "MDI_TN_P2" + PIN 63: "MDI_TP_P3" + PIN 64: "MDI_TN_P3" + PIN 65: "MDI_RP_P3" + PIN 66: "MDI_RN_P3" + PIN 67: "MDI_RP_P4" + PIN 68: "MDI_RN_P4" + PIN 69: "MDI_TP_P4" + PIN 70: "MDI_TN_P4" + PIN 71: "PMIC_SCL" + PIN 72: "PMIC_SDA" + PIN 73: "SPIC1_CLK" + PIN 74: "SPIC1_MOSI" + PIN 75: "SPIC1_MISO" + PIN 76: "SPIC1_CS" + PIN 77: "GPIO_D" + PIN 78: "WATCHDOG" + PIN 79: "RTS3_N" + PIN 80: "CTS3_N" + PIN 81: "TXD3" + PIN 82: "RXD3" + PIN 83: "PERST0_N" + PIN 84: "PERST1_N" + PIN 85: "WLED_N" + PIN 86: "EPHY_LED0_N" + PIN 87: "AUXIN0" + PIN 88: "AUXIN1" + PIN 89: "AUXIN2" + PIN 90: "AUXIN3" + PIN 91: "TXD4" + PIN 92: "RXD4" + PIN 93: "RTS4_N" + PIN 94: "CST4_N" + PIN 95: "PWM1" + PIN 96: "PWM2" + PIN 97: "PWM3" + PIN 98: "PWM4" + PIN 99: "PWM5" + PIN 100: "PWM6" + PIN 101: "PWM7" + PIN 102: "GPIO_E" + +Valid values for function are: + "emmc", "eth", "i2c", "i2s", "ir", "led", "flash", "pcie", + "pmic", "pwm", "sd", "spi", "tdm", "uart", "watchdog" + +Valid values for groups are: +additional data is put followingly with valid value allowing us to know which +applicable function and which relevant pins (in pin#) are able applied for that +group. + + Valid value function pins (in pin#) + ------------------------------------------------------------------------- + "emmc" "emmc" 40, 41, 42, 43, 44, 45, + 47, 48, 49, 50 + "emmc_rst" "emmc" 37 + "esw" "eth" 51, 52, 53, 54, 55, 56, + 57, 58, 59, 60, 61, 62, + 63, 64, 65, 66, 67, 68, + 69, 70 + "esw_p0_p1" "eth" 51, 52, 53, 54, 55, 56, + 57, 58 + "esw_p2_p3_p4" "eth" 59, 60, 61, 62, 63, 64, + 65, 66, 67, 68, 69, 70 + "rgmii_via_esw" "eth" 59, 60, 61, 62, 63, 64, + 65, 66, 67, 68, 69, 70 + "rgmii_via_gmac1" "eth" 59, 60, 61, 62, 63, 64, + 65, 66, 67, 68, 69, 70 + "rgmii_via_gmac2" "eth" 25, 26, 27, 28, 29, 30, + 31, 32, 33, 34, 35, 36 + "mdc_mdio" "eth" 23, 24 + "i2c0" "i2c" 14, 15 + "i2c1_0" "i2c" 55, 56 + "i2c1_1" "i2c" 73, 74 + "i2c1_2" "i2c" 87, 88 + "i2c2_0" "i2c" 57, 58 + "i2c2_1" "i2c" 75, 76 + "i2c2_2" "i2c" 89, 90 + "i2s_in_mclk_bclk_ws" "i2s" 3, 4, 5 + "i2s1_in_data" "i2s" 1 + "i2s2_in_data" "i2s" 16 + "i2s3_in_data" "i2s" 17 + "i2s4_in_data" "i2s" 18 + "i2s_out_mclk_bclk_ws" "i2s" 3, 4, 5 + "i2s1_out_data" "i2s" 2 + "i2s2_out_data" "i2s" 19 + "i2s3_out_data" "i2s" 20 + "i2s4_out_data" "i2s" 21 + "ir_0_tx" "ir" 16 + "ir_1_tx" "ir" 59 + "ir_2_tx" "ir" 99 + "ir_0_rx" "ir" 17 + "ir_1_rx" "ir" 60 + "ir_2_rx" "ir" 100 + "ephy_leds" "led" 86, 91, 92, 93, 94 + "ephy0_led" "led" 86 + "ephy1_led" "led" 91 + "ephy2_led" "led" 92 + "ephy3_led" "led" 93 + "ephy4_led" "led" 94 + "wled" "led" 85 + "par_nand" "flash" 37, 38, 39, 40, 41, 42, + 43, 44, 45, 46, 47, 48, + 49, 50 + "snfi" "flash" 8, 9, 10, 11, 12, 13 + "spi_nor" "flash" 8, 9, 10, 11, 12, 13 + "pcie0_0_waken" "pcie" 14 + "pcie0_1_waken" "pcie" 79 + "pcie1_0_waken" "pcie" 14 + "pcie0_0_clkreq" "pcie" 15 + "pcie0_1_clkreq" "pcie" 80 + "pcie1_0_clkreq" "pcie" 15 + "pcie0_pad_perst" "pcie" 83 + "pcie1_pad_perst" "pcie" 84 + "pmic_bus" "pmic" 71, 72 + "pwm_ch1_0" "pwm" 51 + "pwm_ch1_1" "pwm" 73 + "pwm_ch1_2" "pwm" 95 + "pwm_ch2_0" "pwm" 52 + "pwm_ch2_1" "pwm" 74 + "pwm_ch2_2" "pwm" 96 + "pwm_ch3_0" "pwm" 53 + "pwm_ch3_1" "pwm" 75 + "pwm_ch3_2" "pwm" 97 + "pwm_ch4_0" "pwm" 54 + "pwm_ch4_1" "pwm" 67 + "pwm_ch4_2" "pwm" 76 + "pwm_ch4_3" "pwm" 98 + "pwm_ch5_0" "pwm" 68 + "pwm_ch5_1" "pwm" 77 + "pwm_ch5_2" "pwm" 99 + "pwm_ch6_0" "pwm" 69 + "pwm_ch6_1" "pwm" 78 + "pwm_ch6_2" "pwm" 81 + "pwm_ch6_3" "pwm" 100 + "pwm_ch7_0" "pwm" 70 + "pwm_ch7_1" "pwm" 82 + "pwm_ch7_2" "pwm" 101 + "sd_0" "sd" 16, 17, 18, 19, 20, 21 + "sd_1" "sd" 25, 26, 27, 28, 29, 30 + "spic0_0" "spi" 63, 64, 65, 66 + "spic0_1" "spi" 79, 80, 81, 82 + "spic1_0" "spi" 67, 68, 69, 70 + "spic1_1" "spi" 73, 74, 75, 76 + "spic2_0_wp_hold" "spi" 8, 9 + "spic2_0" "spi" 10, 11, 12, 13 + "tdm_0_out_mclk_bclk_ws" "tdm" 8, 9, 10 + "tdm_0_in_mclk_bclk_ws" "tdm" 11, 12, 13 + "tdm_0_out_data" "tdm" 20 + "tdm_0_in_data" "tdm" 21 + "tdm_1_out_mclk_bclk_ws" "tdm" 57, 58, 59 + "tdm_1_in_mclk_bclk_ws" "tdm" 60, 61, 62 + "tdm_1_out_data" "tdm" 55 + "tdm_1_in_data" "tdm" 56 + "uart0_0_tx_rx" "uart" 6, 7 + "uart1_0_tx_rx" "uart" 55, 56 + "uart1_0_rts_cts" "uart" 57, 58 + "uart1_1_tx_rx" "uart" 73, 74 + "uart1_1_rts_cts" "uart" 75, 76 + "uart2_0_tx_rx" "uart" 3, 4 + "uart2_0_rts_cts" "uart" 1, 2 + "uart2_1_tx_rx" "uart" 51, 52 + "uart2_1_rts_cts" "uart" 53, 54 + "uart2_2_tx_rx" "uart" 59, 60 + "uart2_2_rts_cts" "uart" 61, 62 + "uart2_3_tx_rx" "uart" 95, 96 + "uart3_0_tx_rx" "uart" 57, 58 + "uart3_1_tx_rx" "uart" 81, 82 + "uart3_1_rts_cts" "uart" 79, 80 + "uart4_0_tx_rx" "uart" 61, 62 + "uart4_1_tx_rx" "uart" 91, 92 + "uart4_1_rts_cts" "uart" 93, 94 + "uart4_2_tx_rx" "uart" 97, 98 + "uart4_2_rts_cts" "uart" 95, 96 + "watchdog" "watchdog" 78 + +Example: + + pio: pinctrl@10211000 { + compatible = "mediatek,mt7622-pinctrl"; + reg = <0 0x10211000 0 0x1000>; + gpio-controller; + #gpio-cells = <2>; + + pinctrl_eth_default: eth-default { + mux-mdio { + groups = "mdc_mdio"; + function = "eth"; + drive-strength = <12>; + }; + + mux-gmac2 { + groups = "gmac2"; + function = "eth"; + drive-strength = <12>; + }; + + mux-esw { + groups = "esw"; + function = "eth"; + drive-strength = <8>; + }; + + conf-mdio { + pins = "MDC"; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt new file mode 100644 index 000000000000..e70c79bbbc5b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt @@ -0,0 +1,193 @@ +Qualcomm MSM8998 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8998 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,msm8998-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio149 + Supports mux, bias and drive-strength + + sdc2_clk, sdc2_cmd, sdc2_data + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + gpio, adsp_ext, agera_pll, atest_char, atest_gpsadc0, + atest_gpsadc1, atest_tsens, atest_tsens2, atest_usb1, + atest_usb10, atest_usb11, atest_usb12, atest_usb13, + audio_ref, bimc_dte0, bimc_dte1, blsp10_spi, blsp10_spi_a, + blsp10_spi_b, blsp11_i2c, blsp1_spi, blsp1_spi_a, + blsp1_spi_b, blsp2_spi, blsp9_spi, blsp_i2c1, blsp_i2c2, + blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, + blsp_i2c8, blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12, + blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10, + blsp_spi11, blsp_spi12, blsp_uart1_a, blsp_uart1_b, + blsp_uart2_a, blsp_uart2_b, blsp_uart3_a, blsp_uart3_b, + blsp_uart7_a, blsp_uart7_b, blsp_uart8, blsp_uart8_a, + blsp_uart8_b, blsp_uart9_a, blsp_uart9_b, blsp_uim1_a, + blsp_uim1_b, blsp_uim2_a, blsp_uim2_b, blsp_uim3_a, + blsp_uim3_b, blsp_uim7_a, blsp_uim7_b, blsp_uim8_a, + blsp_uim8_b, blsp_uim9_a, blsp_uim9_b, bt_reset, + btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, + cri_trng0, cri_trng1, dbg_out, ddr_bist, edp_hot, edp_lcd, + gcc_gp1_a, gcc_gp1_b, gcc_gp2_a, gcc_gp2_b, gcc_gp3_a, + gcc_gp3_b, hdmi_cec, hdmi_ddc, hdmi_hot, hdmi_rcv, + isense_dbg, jitter_bist, ldo_en, ldo_update, lpass_slimbus, + m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2, + mdp_vsync3, mdp_vsync_a, mdp_vsync_b, modem_tsync, mss_lte, + nav_dr, nav_pps, pa_indicator, pci_e0, phase_flag, + pll_bypassnl, pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, + pwr_crypto, pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b, + qdss_cti1_a, qdss_cti1_b, qdss, qlink_enable, + qlink_request, qua_mi2s, sd_card, sd_write, sdc40, sdc41, + sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, + spkr_i2s, ssbi1, ssc_irq, ter_mi2s, tgu_ch0, tgu_ch1, + tsense_pwm1, tsense_pwm2, tsif1_clk, tsif1_data, tsif1_en, + tsif1_error, tsif1_sync, tsif2_clk, tsif2_data, tsif2_en, + tsif2_error, tsif2_sync, uim1_clk, uim1_data, uim1_present, + uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, + uim_batt, usb_phy, vfr_1, vsense_clkout, vsense_data0, + vsense_data1, vsense_mode, wlan1_adc0, wlan1_adc1, + wlan2_adc0, wlan2_adc1, + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@03400000 { + compatible = "qcom,msm8998-pinctrl"; + reg = <0x03400000 0xc00000>; + interrupts = <0 208 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + uart_console_active: uart_console_active { + mux { + pins = "gpio4", "gpio5"; + function = "blsp_uart8_a"; + }; + + config { + pins = "gpio4", "gpio5"; + drive-strength = <2>; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 9b4f8041c36a..bb1790e0b176 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -24,6 +24,7 @@ Required Properties: - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller. + - "renesas,pfc-r8a77970": for R8A77970 (R-Car V3M) compatible pin-controller. - "renesas,pfc-r8a77995": for R8A77995 (R-Car D3) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.txt new file mode 100644 index 000000000000..8173b12138ad --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.txt @@ -0,0 +1,27 @@ +UniPhier SoCs pin controller + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-ld4-pinctrl" - for LD4 SoC + "socionext,uniphier-pro4-pinctrl" - for Pro4 SoC + "socionext,uniphier-sld8-pinctrl" - for sLD8 SoC + "socionext,uniphier-pro5-pinctrl" - for Pro5 SoC + "socionext,uniphier-pxs2-pinctrl" - for PXs2 SoC + "socionext,uniphier-ld6b-pinctrl" - for LD6b SoC + "socionext,uniphier-ld11-pinctrl" - for LD11 SoC + "socionext,uniphier-ld20-pinctrl" - for LD20 SoC + "socionext,uniphier-pxs3-pinctrl" - for PXs3 SoC + +Note: +The UniPhier pinctrl should be a subnode of a "syscon" compatible node. + +Example: + soc-glue@5f800000 { + compatible = "socionext,uniphier-pro4-soc-glue", + "simple-mfd", "syscon"; + reg = <0x5f800000 0x2000>; + + pinctrl: pinctrl { + compatible = "socionext,uniphier-pro4-pinctrl"; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 58c2a4c229db..2c46f30b62c5 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -12,6 +12,8 @@ Required properies: "st,stm32f469-pinctrl" "st,stm32f746-pinctrl" "st,stm32h743-pinctrl" + "st,stm32mp157-pinctrl" + "st,stm32mp157-z-pinctrl" - #address-cells: The value of this property must be 1 - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to |