Merge branch 'adin1100-industrial-PHY-support'

Alexandru Tachici says:

====================
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY

The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.

The ADIN1100 uses Auto-Negotiation capability in accordance
with IEEE 802.3 Clause 98, providing a mechanism for
exchanging information between PHYs to allow link partners to
agree to a common mode of operation.

The concluded operating mode is the transmit amplitude mode and
master/slave preference common across the two devices.

Both device and LP advertise their ability and request for
increased transmit at:
- BASE-T1 autonegotiation advertisement register [47:32]\
Clause 45.2.7.21 of Standard 802.3
- BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability
- BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request

For 2.4 Vpp (high level transmit) operation, both devices need
to have the High Level Transmit Operating Mode Ability bit set,
and only one of them needs to have the High Level Transmit
Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level
will be used.

Settings for eth1:
	Supported ports: [ TP	 MII ]
	Supported link modes:   10baseT1L/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT1L/Full
	Advertised pause frame use: No
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  10baseT1L/Full
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported
	Speed: 10Mb/s
	Duplex: Full
	Auto-negotiation: on
	master-slave cfg: preferred slave
	master-slave status: slave
	Port: Twisted Pair
	PHYAD: 0
	Transceiver: external
	MDI-X: Unknown
	Link detected: yes
	SQI: 7/7

1. Add basic support for ADIN1100.

Alexandru Ardelean (1):
  net: phy: adin1100: Add initial support for ADIN1100 industrial PHY

1. Added 10baset-T1L link modes.

2. Added 10-BasetT1L registers.

3. Added Base-T1 auto-negotiation registers. For Base-T1 these
registers decide master/slave status and TX voltage of the
device and link partner.

4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call
Base-T1 functions where registers don't match, like the auto-negotiation ones.

5. Convert MSE to SQI using a predefined table and allow user access
through ethtool.

6. DT bindings for the 2.4 Vpp transmit mode.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

4 files changed, 150 insertions, 1 deletions

diff --git a/include/linux/mdio.h b/include/linux/mdio.h
index ecac96d52e01..00177567cfef 100644
--- a/include/linux/mdio.h
+++ b/include/linux/mdio.h
@@ -340,6 +340,76 @@ static inline void mii_10gbt_stat_mod_linkmode_lpa_t(unsigned long *advertising,
 			 advertising, lpa & MDIO_AN_10GBT_STAT_LP10G);
 }
 
+/**
+ * mii_t1_adv_l_mod_linkmode_t
+ * @advertising: target the linkmode advertisement settings
+ * @lpa: value of the BASE-T1 Autonegotiation Advertisement [15:0] Register
+ *
+ * A small helper function that translates BASE-T1 Autonegotiation
+ * Advertisement [15:0] Register bits to linkmode advertisement settings.
+ * Other bits in advertising aren't changed.
+ */
+static inline void mii_t1_adv_l_mod_linkmode_t(unsigned long *advertising, u32 lpa)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT, advertising,
+			 lpa & MDIO_AN_T1_ADV_L_PAUSE_CAP);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, advertising,
+			 lpa & MDIO_AN_T1_ADV_L_PAUSE_ASYM);
+}
+
+/**
+ * mii_t1_adv_m_mod_linkmode_t
+ * @advertising: target the linkmode advertisement settings
+ * @lpa: value of the BASE-T1 Autonegotiation Advertisement [31:16] Register
+ *
+ * A small helper function that translates BASE-T1 Autonegotiation
+ * Advertisement [31:16] Register bits to linkmode advertisement settings.
+ * Other bits in advertising aren't changed.
+ */
+static inline void mii_t1_adv_m_mod_linkmode_t(unsigned long *advertising, u32 lpa)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+			 advertising, lpa & MDIO_AN_T1_ADV_M_B10L);
+}
+
+/**
+ * linkmode_adv_to_mii_t1_adv_l_t
+ * @advertising: the linkmode advertisement settings
+ *
+ * A small helper function that translates linkmode advertisement
+ * settings to phy autonegotiation advertisements for the
+ * BASE-T1 Autonegotiation Advertisement [15:0] Register.
+ */
+static inline u32 linkmode_adv_to_mii_t1_adv_l_t(unsigned long *advertising)
+{
+	u32 result = 0;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT, advertising))
+		result |= MDIO_AN_T1_ADV_L_PAUSE_CAP;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, advertising))
+		result |= MDIO_AN_T1_ADV_L_PAUSE_ASYM;
+
+	return result;
+}
+
+/**
+ * linkmode_adv_to_mii_t1_adv_m_t
+ * @advertising: the linkmode advertisement settings
+ *
+ * A small helper function that translates linkmode advertisement
+ * settings to phy autonegotiation advertisements for the
+ * BASE-T1 Autonegotiation Advertisement [31:16] Register.
+ */
+static inline u32 linkmode_adv_to_mii_t1_adv_m_t(unsigned long *advertising)
+{
+	u32 result = 0;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, advertising))
+		result |= MDIO_AN_T1_ADV_M_B10L;
+
+	return result;
+}
+
 int __mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
 int __mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
 int __mdiobus_modify_changed(struct mii_bus *bus, int addr, u32 regnum,
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 36ca2b5c2253..2d12054932ba 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -65,7 +65,7 @@ extern const int phy_basic_ports_array[3];
 extern const int phy_fibre_port_array[1];
 extern const int phy_all_ports_features_array[7];
 extern const int phy_10_100_features_array[4];
-extern const int phy_basic_t1_features_array[2];
+extern const int phy_basic_t1_features_array[3];
 extern const int phy_gbit_features_array[2];
 extern const int phy_10gbit_features_array[1];
 
@@ -570,6 +570,7 @@ struct macsec_ops;
  * @autoneg_complete: Flag auto negotiation of the link has completed
  * @mdix: Current crossover
  * @mdix_ctrl: User setting of crossover
+ * @pma_extable: Cached value of PMA/PMD Extended Abilities Register
  * @interrupts: Flag interrupts have been enabled
  * @interface: enum phy_interface_t value
  * @skb: Netlink message for cable diagnostics
@@ -698,6 +699,8 @@ struct phy_device {
 	u8 mdix;
 	u8 mdix_ctrl;
 
+	int pma_extable;
+
 	void (*phy_link_change)(struct phy_device *phydev, bool up);
 	void (*adjust_link)(struct net_device *dev);
 
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index 7bc4b8def12c..e0f0ee9bc89e 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -1691,6 +1691,7 @@ enum ethtool_link_mode_bit_indices {
 	ETHTOOL_LINK_MODE_400000baseCR4_Full_BIT	 = 89,
 	ETHTOOL_LINK_MODE_100baseFX_Half_BIT		 = 90,
 	ETHTOOL_LINK_MODE_100baseFX_Full_BIT		 = 91,
+	ETHTOOL_LINK_MODE_10baseT1L_Full_BIT		 = 92,
 	/* must be last entry */
 	__ETHTOOL_LINK_MODE_MASK_NBITS
 };
diff --git a/include/uapi/linux/mdio.h b/include/uapi/linux/mdio.h
index c54e6eae5366..75b7257a51e1 100644
--- a/include/uapi/linux/mdio.h
+++ b/include/uapi/linux/mdio.h
@@ -67,6 +67,19 @@
 #define MDIO_PCS_10GBRT_STAT2	33	/* 10GBASE-R/-T PCS status 2 */
 #define MDIO_AN_10GBT_CTRL	32	/* 10GBASE-T auto-negotiation control */
 #define MDIO_AN_10GBT_STAT	33	/* 10GBASE-T auto-negotiation status */
+#define MDIO_B10L_PMA_CTRL	2294	/* 10BASE-T1L PMA control */
+#define MDIO_PMA_10T1L_STAT	2295	/* 10BASE-T1L PMA status */
+#define MDIO_PCS_10T1L_CTRL	2278	/* 10BASE-T1L PCS control */
+#define MDIO_PMA_PMD_BT1	18	/* BASE-T1 PMA/PMD extended ability */
+#define MDIO_AN_T1_CTRL		512	/* BASE-T1 AN control */
+#define MDIO_AN_T1_STAT		513	/* BASE-T1 AN status */
+#define MDIO_AN_T1_ADV_L	514	/* BASE-T1 AN advertisement register [15:0] */
+#define MDIO_AN_T1_ADV_M	515	/* BASE-T1 AN advertisement register [31:16] */
+#define MDIO_AN_T1_ADV_H	516	/* BASE-T1 AN advertisement register [47:32] */
+#define MDIO_AN_T1_LP_L		517	/* BASE-T1 AN LP Base Page ability register [15:0] */
+#define MDIO_AN_T1_LP_M		518	/* BASE-T1 AN LP Base Page ability register [31:16] */
+#define MDIO_AN_T1_LP_H		519	/* BASE-T1 AN LP Base Page ability register [47:32] */
+#define MDIO_PMA_PMD_BT1_CTRL	2100	/* BASE-T1 PMA/PMD control register */
 
 /* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */
 #define MDIO_PMA_LASI_RXCTRL	0x9000	/* RX_ALARM control */
@@ -159,6 +172,7 @@
 #define MDIO_PMA_CTRL2_10BT		0x000f	/* 10BASE-T type */
 #define MDIO_PMA_CTRL2_2_5GBT		0x0030  /* 2.5GBaseT type */
 #define MDIO_PMA_CTRL2_5GBT		0x0031  /* 5GBaseT type */
+#define MDIO_PMA_CTRL2_BASET1		0x003D  /* BASE-T1 type */
 #define MDIO_PCS_CTRL2_TYPE		0x0003	/* PCS type selection */
 #define MDIO_PCS_CTRL2_10GBR		0x0000	/* 10GBASE-R type */
 #define MDIO_PCS_CTRL2_10GBX		0x0001	/* 10GBASE-X type */
@@ -212,6 +226,7 @@
 #define MDIO_PMA_EXTABLE_1000BKX	0x0040	/* 1000BASE-KX ability */
 #define MDIO_PMA_EXTABLE_100BTX		0x0080	/* 100BASE-TX ability */
 #define MDIO_PMA_EXTABLE_10BT		0x0100	/* 10BASE-T ability */
+#define MDIO_PMA_EXTABLE_BT1		0x0800	/* BASE-T1 ability */
 #define MDIO_PMA_EXTABLE_NBT		0x4000  /* 2.5/5GBASE-T ability */
 
 /* PHY XGXS lane state register. */
@@ -268,6 +283,66 @@
 #define MDIO_AN_10GBT_STAT_MS		0x4000	/* Master/slave config */
 #define MDIO_AN_10GBT_STAT_MSFLT	0x8000	/* Master/slave config fault */
 
+/* 10BASE-T1L PMA control */
+#define MDIO_PMA_10T1L_CTRL_LB_EN	0x0001	/* Enable loopback mode */
+#define MDIO_PMA_10T1L_CTRL_EEE_EN	0x0400	/* Enable EEE mode */
+#define MDIO_PMA_10T1L_CTRL_LOW_POWER	0x0800	/* Low-power mode */
+#define MDIO_PMA_10T1L_CTRL_2V4_EN	0x1000	/* Enable 2.4 Vpp operating mode */
+#define MDIO_PMA_10T1L_CTRL_TX_DIS	0x4000	/* Transmit disable */
+#define MDIO_PMA_10T1L_CTRL_PMA_RST	0x8000	/* MA reset */
+
+/* 10BASE-T1L PMA status register. */
+#define MDIO_PMA_10T1L_STAT_LINK	0x0001	/* PMA receive link up */
+#define MDIO_PMA_10T1L_STAT_FAULT	0x0002	/* Fault condition detected */
+#define MDIO_PMA_10T1L_STAT_POLARITY	0x0004	/* Receive polarity is reversed */
+#define MDIO_PMA_10T1L_STAT_RECV_FAULT	0x0200	/* Able to detect fault on receive path */
+#define MDIO_PMA_10T1L_STAT_EEE		0x0400	/* PHY has EEE ability */
+#define MDIO_PMA_10T1L_STAT_LOW_POWER	0x0800	/* PMA has low-power ability */
+#define MDIO_PMA_10T1L_STAT_2V4_ABLE	0x1000	/* PHY has 2.4 Vpp operating mode ability */
+#define MDIO_PMA_10T1L_STAT_LB_ABLE	0x2000	/* PHY has loopback ability */
+
+/* 10BASE-T1L PCS control register. */
+#define MDIO_PCS_10T1L_CTRL_LB		0x4000	/* Enable PCS level loopback mode */
+#define MDIO_PCS_10T1L_CTRL_RESET	0x8000	/* PCS reset */
+
+/* BASE-T1 PMA/PMD extended ability register. */
+#define MDIO_PMA_PMD_BT1_B10L_ABLE	0x0004	/* 10BASE-T1L Ability */
+
+/* BASE-T1 auto-negotiation advertisement register [15:0] */
+#define MDIO_AN_T1_ADV_L_PAUSE_CAP	ADVERTISE_PAUSE_CAP
+#define MDIO_AN_T1_ADV_L_PAUSE_ASYM	ADVERTISE_PAUSE_ASYM
+#define MDIO_AN_T1_ADV_L_FORCE_MS	0x1000	/* Force Master/slave Configuration */
+#define MDIO_AN_T1_ADV_L_REMOTE_FAULT	ADVERTISE_RFAULT
+#define MDIO_AN_T1_ADV_L_ACK		ADVERTISE_LPACK
+#define MDIO_AN_T1_ADV_L_NEXT_PAGE_REQ	ADVERTISE_NPAGE
+
+/* BASE-T1 auto-negotiation advertisement register [31:16] */
+#define MDIO_AN_T1_ADV_M_B10L		0x4000	/* device is compatible with 10BASE-T1L */
+#define MDIO_AN_T1_ADV_M_MST		0x0010	/* advertise master preference */
+
+/* BASE-T1 auto-negotiation advertisement register [47:32] */
+#define MDIO_AN_T1_ADV_H_10L_TX_HI_REQ	0x1000	/* 10BASE-T1L High Level Transmit Request */
+#define MDIO_AN_T1_ADV_H_10L_TX_HI	0x2000	/* 10BASE-T1L High Level Transmit Ability */
+
+/* BASE-T1 AN LP Base Page ability register [15:0] */
+#define MDIO_AN_T1_LP_L_PAUSE_CAP	LPA_PAUSE_CAP
+#define MDIO_AN_T1_LP_L_PAUSE_ASYM	LPA_PAUSE_ASYM
+#define MDIO_AN_T1_LP_L_FORCE_MS	0x1000	/* LP Force Master/slave Configuration */
+#define MDIO_AN_T1_LP_L_REMOTE_FAULT	LPA_RFAULT
+#define MDIO_AN_T1_LP_L_ACK		LPA_LPACK
+#define MDIO_AN_T1_LP_L_NEXT_PAGE_REQ	LPA_NPAGE
+
+/* BASE-T1 AN LP Base Page ability register [31:16] */
+#define MDIO_AN_T1_LP_M_MST		0x0010	/* LP master preference */
+#define MDIO_AN_T1_LP_M_B10L		0x4000	/* LP is compatible with 10BASE-T1L */
+
+/* BASE-T1 AN LP Base Page ability register [47:32] */
+#define MDIO_AN_T1_LP_H_10L_TX_HI_REQ	0x1000	/* 10BASE-T1L High Level LP Transmit Request */
+#define MDIO_AN_T1_LP_H_10L_TX_HI	0x2000	/* 10BASE-T1L High Level LP Transmit Ability */
+
+/* BASE-T1 PMA/PMD control register */
+#define MDIO_PMA_PMD_BT1_CTRL_CFG_MST	0x4000 /* MASTER-SLAVE config value */
+
 /* EEE Supported/Advertisement/LP Advertisement registers.
  *
  * EEE capability Register (3.20), Advertisement (7.60) and