PCI/NPEM: Add Native PCIe Enclosure Management support

Native PCIe Enclosure Management (NPEM, PCIe r6.1 sec 6.28) allows managing
LEDs in storage enclosures. NPEM is indication oriented and it does not
give direct access to LEDs. Although each indication *could* represent an
individual LED, multiple indications could also be represented as a single,
multi-color LED or a single LED blinking in a specific interval.  The
specification leaves that open.

Each enabled indication (capability register bit on) is represented as a
ledclass_dev which can be controlled through sysfs. For every ledclass
device only 2 brightness states are allowed: LED_ON (1) or LED_OFF (0).
This corresponds to the NPEM control register (Indication bit on/off).

Ledclass devices appear in sysfs as child devices (subdirectory) of PCI
device which has an NPEM Extended Capability and indication is enabled in
NPEM capability register. For example, these are LEDs created for pcieport
"10000:02:05.0" on my setup:

  leds/
  ├── 10000:02:05.0:enclosure:fail
  ├── 10000:02:05.0:enclosure:locate
  ├── 10000:02:05.0:enclosure:ok
  └── 10000:02:05.0:enclosure:rebuild

They can be also found in "/sys/class/leds" directory. The parent PCIe
device domain/bus/device/function address is used to guarantee uniqueness
across leds subsystem.

To enable/disable a "fail" indication, the "brightness" file can be edited:

  echo 1 > ./leds/10000:02:05.0:enclosure:fail/brightness
  echo 0 > ./leds/10000:02:05.0:enclosure:fail/brightness

PCIe r6.1, sec 7.9.19.2 defines the possible indications.

Multiple indications for same parent PCIe device can conflict and hardware
may update them when processing new request. To avoid issues, driver
refresh all indications by reading back control register.

This driver expects to be the exclusive NPEM extended capability manager.
It waits up to 1 second after imposing new request, it doesn't verify if
controller is busy before write, and it assumes the mutex lock gives
protection from concurrent updates.

If _DSM LED management is available, we assume the platform may be using
NPEM for its own purposes (see PCI Firmware Spec r3.3 sec 4.7), so the
driver does not use NPEM. A future patch will add _DSM support; an info
message notes whether NPEM or _DSM is being used.

NPEM is a PCIe extended capability so it should be registered in
pcie_init_capabilities() but it is not possible due to LED dependency.  The
parent pci_device must be added earlier for led_classdev_register() to be
successful. NPEM does not require configuration on kernel side, so it is
safe to register LED devices later.

Link: https://lore.kernel.org/r/20240904104848.23480-3-mariusz.tkaczyk@linux.intel.com
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

1 files changed, 2 insertions, 0 deletions

diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c
index 910387e5bdbf..da9629c3a688 100644
--- a/drivers/pci/remove.c
+++ b/drivers/pci/remove.c
@@ -34,6 +34,8 @@ static void pci_destroy_dev(struct pci_dev *dev)
 	if (!dev->dev.kobj.parent)
 		return;
 
+	pci_npem_remove(dev);
+
 	device_del(&dev->dev);
 
 	down_write(&pci_bus_sem);