Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

9 files changed, 812 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/actions/Makefile b/arch/arm/boot/dts/actions/Makefile
new file mode 100644
index 000000000000..f384e4a48e6f
--- /dev/null
+++ b/arch/arm/boot/dts/actions/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ACTIONS) += \
+	owl-s500-cubieboard6.dtb \
+	owl-s500-guitar-bb-rev-b.dtb \
+	owl-s500-labrador-base-m.dtb \
+	owl-s500-roseapplepi.dtb \
+	owl-s500-sparky.dtb
diff --git a/arch/arm/boot/dts/actions/owl-s500-cubieboard6.dts b/arch/arm/boot/dts/actions/owl-s500-cubieboard6.dts
new file mode 100644
index 000000000000..c2b02895910c
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-cubieboard6.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Cubietech CubieBoard6
+ *
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "owl-s500.dtsi"
+
+/ {
+	compatible = "cubietech,cubieboard6", "actions,s500";
+	model = "CubieBoard6";
+
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x80000000>;
+	};
+};
+
+&timer {
+	clocks = <&hosc>;
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-guitar-bb-rev-b.dts b/arch/arm/boot/dts/actions/owl-s500-guitar-bb-rev-b.dts
new file mode 100644
index 000000000000..7ae34a23e320
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-guitar-bb-rev-b.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016-2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "owl-s500-guitar.dtsi"
+
+/ {
+	compatible = "lemaker,guitar-bb-rev-b", "lemaker,guitar", "actions,s500";
+	model = "LeMaker Guitar Base Board rev. B";
+
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-guitar.dtsi b/arch/arm/boot/dts/actions/owl-s500-guitar.dtsi
new file mode 100644
index 000000000000..81cc39871f17
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-guitar.dtsi
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * LeMaker Guitar SoM
+ *
+ * Copyright (c) 2016-2017 Andreas Färber
+ */
+
+#include "owl-s500.dtsi"
+
+/ {
+	compatible = "lemaker,guitar", "actions,s500";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x40000000>;
+	};
+};
+
+&timer {
+	clocks = <&hosc>;
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts b/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts
new file mode 100644
index 000000000000..1585e33f703b
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Caninos Labrador Base Board
+ *
+ * Copyright (c) 2019-2020 Matheus Castello
+ */
+
+/dts-v1/;
+
+#include "owl-s500-labrador-v2.dtsi"
+
+/ {
+	model = "Caninos Labrador Core v2 on Labrador Base-M v1";
+	compatible = "caninos,labrador-base-m",
+		     "caninos,labrador-v2", "actions,s500";
+
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi b/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi
new file mode 100644
index 000000000000..883ff2f9886d
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Caninos Labrador SoM V2
+ *
+ * Copyright (c) 2019-2020 Matheus Castello
+ */
+
+#include "owl-s500.dtsi"
+
+/ {
+	model = "Caninos Labrador Core V2.1";
+	compatible = "caninos,labrador-v2", "actions,s500";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x80000000>;
+	};
+};
+
+&timer {
+	clocks = <&hosc>;
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts
new file mode 100644
index 000000000000..eb555f385283
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts
@@ -0,0 +1,299 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Roseapple Pi
+ *
+ * Copyright (C) 2020-2021 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "owl-s500.dtsi"
+
+/ {
+	compatible = "roseapplepi,roseapplepi", "actions,s500";
+	model = "Roseapple Pi";
+
+	aliases {
+		mmc0 = &mmc0;
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x80000000>; /* 2GB */
+	};
+
+	syspwr: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SYSPWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	atc260x: pmic@65 {
+		compatible = "actions,atc2603c";
+		reg = <0x65>;
+		interrupt-parent = <&sirq>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+
+		reset-time-sec = <6>;
+
+		regulators {
+			compatible = "actions,atc2603c-regulator";
+
+			dcdc1-supply = <&syspwr>;
+			dcdc2-supply = <&syspwr>;
+			dcdc3-supply = <&syspwr>;
+			ldo1-supply = <&syspwr>;
+			ldo2-supply = <&syspwr>;
+			ldo3-supply = <&syspwr>;
+			ldo5-supply = <&syspwr>;
+			ldo6-supply = <&syspwr>;
+			ldo7-supply = <&syspwr>;
+			ldo8-supply = <&syspwr>;
+			ldo11-supply = <&syspwr>;
+			ldo12-supply = <&syspwr>;
+			switchldo1-supply = <&vcc>;
+
+			vdd_cpu: dcdc1 {
+				regulator-name = "VDD_CPU";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+			};
+
+			vddq: dcdc2 {
+				regulator-name = "VDDQ";
+				regulator-min-microvolt = <1300000>;
+				regulator-max-microvolt = <2150000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcc: dcdc3 {
+				regulator-name = "VCC";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vcc_3v3: ldo1 {
+				regulator-name = "VCC_3V3";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			avcc: ldo2 {
+				regulator-name = "AVCC";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_1v8: ldo3 {
+				regulator-name = "VDD_1V8";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vcc_3v1: ldo5 {
+				regulator-name = "VCC_3V1";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			avdd: ldo6 {
+				regulator-name = "AVDD";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+			};
+
+			sens_1v8: ldo7 {
+				regulator-name = "SENS_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo8: ldo8 {
+				regulator-name = "LDO8";
+				regulator-min-microvolt = <2300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			svcc: ldo11 {
+				regulator-name = "SVCC";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			rtc_vdd: ldo12 {
+				regulator-name = "RTC_VDD";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			sd_vcc: switchldo1 {
+				regulator-name = "SD_VCC";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+};
+
+&i2c2 {
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+};
+
+&pinctrl {
+	i2c0_pins: i2c0-pins {
+		pinmux {
+			groups = "i2c0_mfp";
+			function = "i2c0";
+		};
+
+		pinconf {
+			pins = "i2c0_sclk", "i2c0_sdata";
+			bias-pull-up;
+		};
+	};
+
+	i2c1_pins: i2c1-pins {
+		pinconf {
+			pins = "i2c1_sclk", "i2c1_sdata";
+			bias-pull-up;
+		};
+	};
+
+	i2c2_pins: i2c2-pins {
+		pinconf {
+			pins = "i2c2_sclk", "i2c2_sdata";
+			bias-pull-up;
+		};
+	};
+
+	mmc0_pins: mmc0-pins {
+		pinmux {
+			groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
+				 "sd0_cmd_mfp", "sd0_clk_mfp";
+			function = "sd0";
+		};
+
+		drv-pinconf {
+			groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv";
+			drive-strength = <8>;
+		};
+
+		bias0-pinconf {
+			pins = "sd0_d0", "sd0_d1", "sd0_d2",
+			       "sd0_d3", "sd0_cmd";
+			bias-pull-up;
+		};
+
+		bias1-pinconf {
+			pins = "sd0_clk";
+			bias-pull-down;
+		};
+	};
+
+	ethernet_pins: ethernet-pins {
+		eth_rmii-pinmux {
+			groups = "rmii_txd0_mfp", "rmii_txd1_mfp",
+				 "rmii_rxd0_mfp", "rmii_rxd1_mfp",
+				 "rmii_txen_mfp", "rmii_rxen_mfp",
+				 "rmii_crs_dv_mfp", "rmii_ref_clk_mfp";
+			function = "eth_rmii";
+		};
+
+		phy_clk-pinmux {
+			groups = "clko_25m_mfp";
+			function = "clko_25m";
+		};
+
+		ref_clk-pinconf {
+			groups = "rmii_ref_clk_drv";
+			drive-strength = <2>;
+		};
+
+	};
+};
+
+/* uSD */
+&mmc0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	no-sdio;
+	no-mmc;
+	no-1-8-v;
+	cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&sd_vcc>;
+	vqmmc-supply = <&sd_vcc>;
+};
+
+&ethernet {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&eth_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&pinctrl 88 GPIO_ACTIVE_LOW>; /* GPIOC24 */
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <150000>;
+
+		eth_phy: ethernet-phy@3 {
+			reg = <0x3>;
+			max-speed = <100>;
+			interrupt-parent = <&sirq>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&twd_timer {
+	status = "okay";
+};
+
+&timer {
+	clocks = <&hosc>;
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-sparky.dts b/arch/arm/boot/dts/actions/owl-s500-sparky.dts
new file mode 100644
index 000000000000..9d8f7336bec0
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-sparky.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Allo.com Sparky
+ *
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "owl-s500.dtsi"
+
+/ {
+	compatible = "allo,sparky", "actions,s500";
+	model = "Allo.com Sparky";
+
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x40000000>; /* 1 or 2 GiB */
+	};
+};
+
+&timer {
+	clocks = <&hosc>;
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500.dtsi b/arch/arm/boot/dts/actions/owl-s500.dtsi
new file mode 100644
index 000000000000..739b4b9cec8c
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500.dtsi
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Actions Semi S500 SoC
+ *
+ * Copyright (c) 2016-2017 Andreas Färber
+ */
+
+#include <dt-bindings/clock/actions,s500-cmu.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/owl-s500-powergate.h>
+#include <dt-bindings/reset/actions,s500-reset.h>
+
+/ {
+	compatible = "actions,s500";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+	};
+
+	chosen {
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x0>;
+			enable-method = "actions,s500-smp";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x1>;
+			enable-method = "actions,s500-smp";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x2>;
+			enable-method = "actions,s500-smp";
+			power-domains = <&sps S500_PD_CPU2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x3>;
+			enable-method = "actions,s500-smp";
+			power-domains = <&sps S500_PD_CPU3>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	hosc: hosc {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		#clock-cells = <0>;
+	};
+
+	losc: losc {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		scu: scu@b0020000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0xb0020000 0x100>;
+		};
+
+		global_timer: timer@b0020200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0xb0020200 0x100>;
+			interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+			status = "disabled";
+		};
+
+		twd_timer: timer@b0020600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0xb0020600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+			status = "disabled";
+		};
+
+		twd_wdt: wdt@b0020620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0xb0020620 0xe0>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@b0021000 {
+			compatible = "arm,cortex-a9-gic";
+			reg = <0xb0021000 0x1000>,
+			      <0xb0020100 0x0100>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		l2: cache-controller@b0022000 {
+			compatible = "arm,pl310-cache";
+			reg = <0xb0022000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			arm,tag-latency = <3 3 2>;
+			arm,data-latency = <5 3 3>;
+		};
+
+		uart0: serial@b0120000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0120000 0x2000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@b0122000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0122000 0x2000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@b0124000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0124000 0x2000>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@b0126000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0126000 0x2000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@b0128000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0128000 0x2000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@b012a000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb012a000 0x2000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART5>;
+			status = "disabled";
+		};
+
+		uart6: serial@b012c000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb012c000 0x2000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART6>;
+			status = "disabled";
+		};
+
+		cmu: clock-controller@b0160000 {
+			compatible = "actions,s500-cmu";
+			reg = <0xb0160000 0x8000>;
+			clocks = <&hosc>, <&losc>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		i2c0: i2c@b0170000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb0170000 0x4000>;
+			clocks = <&cmu CLK_I2C0>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@b0174000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb0174000 0x4000>;
+			clocks = <&cmu CLK_I2C1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@b0178000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb0178000 0x4000>;
+			clocks = <&cmu CLK_I2C2>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@b017c000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb017c000 0x4000>;
+			clocks = <&cmu CLK_I2C3>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		sirq: interrupt-controller@b01b0200 {
+			compatible = "actions,s500-sirq";
+			reg = <0xb01b0200 0x4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ0 */
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ1 */
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; /* SIRQ2 */
+		};
+
+		timer: timer@b0168000 {
+			compatible = "actions,s500-timer";
+			reg = <0xb0168000 0x8000>;
+			interrupts = <GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "2hz0", "2hz1", "timer0", "timer1";
+		};
+
+		sps: power-controller@b01b0100 {
+			compatible = "actions,s500-sps";
+			reg = <0xb01b0100 0x100>;
+			#power-domain-cells = <1>;
+		};
+
+		pinctrl: pinctrl@b01b0000 {
+			compatible = "actions,s500-pinctrl";
+			reg = <0xb01b0000 0x40>, /* GPIO */
+			      <0xb01b0040 0x10>, /* Multiplexing Control */
+			      <0xb01b0060 0x18>, /* PAD Control */
+			      <0xb01b0080 0xc>;  /* PAD Drive Capacity */
+			clocks = <&cmu CLK_GPIO>;
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 132>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, /* GPIOA */
+				     <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, /* GPIOB */
+				     <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, /* GPIOC */
+				     <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, /* GPIOD */
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; /* GPIOE */
+		};
+
+		dma: dma-controller@b0260000 {
+			compatible = "actions,s500-dma";
+			reg = <0xb0260000 0xd00>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			dma-channels = <12>;
+			dma-requests = <46>;
+			clocks = <&cmu CLK_DMAC>;
+			power-domains = <&sps S500_PD_DMA>;
+		};
+
+		mmc0: mmc@b0230000 {
+			compatible = "actions,s500-mmc", "actions,owl-mmc";
+			reg = <0xb0230000 0x38>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_SD0>;
+			resets = <&cmu RESET_SD0>;
+			dmas = <&dma 2>;
+			dma-names = "mmc";
+			status = "disabled";
+		};
+
+		mmc1: mmc@b0234000 {
+			compatible = "actions,s500-mmc", "actions,owl-mmc";
+			reg = <0xb0234000 0x38>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_SD1>;
+			resets = <&cmu RESET_SD1>;
+			dmas = <&dma 3>;
+			dma-names = "mmc";
+			status = "disabled";
+		};
+
+		mmc2: mmc@b0238000 {
+			compatible = "actions,s500-mmc", "actions,owl-mmc";
+			reg = <0xb0238000 0x38>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_SD2>;
+			resets = <&cmu RESET_SD2>;
+			dmas = <&dma 4>;
+			dma-names = "mmc";
+			status = "disabled";
+		};
+
+		ethernet: ethernet@b0310000 {
+			compatible = "actions,s500-emac", "actions,owl-emac";
+			reg = <0xb0310000 0x10000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_ETHERNET>, <&cmu CLK_RMII_REF>;
+			clock-names = "eth", "rmii";
+			resets = <&cmu RESET_ETHERNET>;
+			status = "disabled";
+		};
+	};
+};