Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
  powerpc: Fix CHRP PCI config access for indirect_pci
  powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
  powerpc: Fix 32-bit SMP boot on CHRP
  powerpc: Fix link errors on 32-bit machines using legacy DMA
  powerpc/pci: Improve detection of unassigned bridge resources
  hvc_console: Fix free_irq in spinlocked section
  powerpc: Get USE_STRICT_MM_TYPECHECKS working again
  powerpc: Reflect the used arguments in machine_init() prototype
  powerpc: Fix DMA offset for non-coherent DMA
  powerpc: fix fsl_upm nand driver modular build
  powerpc/83xx: add NAND support for the MPC8360E-RDK boards
  powerpc: FPGA support for GE Fanuc SBC610
  i2c: MPC8349E-mITX Power Management and GPIO expander driver
  powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
  powerpc: document the "fsl,ssi-dma-channel" compatible property
  powerpc: disable CHRP and PMAC support in various defconfigs
  OF: add fsl,mcu-mpc8349emitx to the exception list
  powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
  powerpc: remove support for bootmem-allocated memory for the DIU driver
  powerpc: remove non-dependent load fsl_booke PTE_64BIT
  ...

7 files changed, 114 insertions, 158 deletions

diff --git a/Documentation/powerpc/00-INDEX b/Documentation/powerpc/00-INDEX
index 29d839ce7327..e3960b8c8689 100644
--- a/Documentation/powerpc/00-INDEX
+++ b/Documentation/powerpc/00-INDEX
@@ -18,10 +18,6 @@ mpc52xx.txt
 	- Linux 2.6.x on MPC52xx family
 mpc52xx-device-tree-bindings.txt
 	- MPC5200 Device Tree Bindings
-ppc_htab.txt
-	- info about the Linux/PPC /proc/ppc_htab entry
-smp.txt
-	- use and state info about Linux/PPC on MP machines
 sound.txt
 	- info on sound support under Linux/PPC
 zImage_layout.txt
diff --git a/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt b/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt
new file mode 100644
index 000000000000..35a465362408
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt
@@ -0,0 +1,40 @@
+* Freescale 83xx and 512x PCI bridges
+
+Freescale 83xx and 512x SOCs include the same pci bridge core.
+
+83xx/512x specific notes:
+- reg: should contain two address length tuples
+    The first is for the internal pci bridge registers
+    The second is for the pci config space access registers
+
+Example (MPC8313ERDB)
+	pci0: pci@e0008500 {
+		cell-index = <1>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+				/* IDSEL 0x0E -mini PCI */
+				 0x7000 0x0 0x0 0x1 &ipic 18 0x8
+				 0x7000 0x0 0x0 0x2 &ipic 18 0x8
+				 0x7000 0x0 0x0 0x3 &ipic 18 0x8
+				 0x7000 0x0 0x0 0x4 &ipic 18 0x8
+
+				/* IDSEL 0x0F - PCI slot */
+				 0x7800 0x0 0x0 0x1 &ipic 17 0x8
+				 0x7800 0x0 0x0 0x2 &ipic 18 0x8
+				 0x7800 0x0 0x0 0x3 &ipic 17 0x8
+				 0x7800 0x0 0x0 0x4 &ipic 18 0x8>;
+		interrupt-parent = <&ipic>;
+		interrupts = <66 0x8>;
+		bus-range = <0x0 0x0>;
+		ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
+			  0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+			  0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+		clock-frequency = <66666666>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0xe0008500 0x100		/* internal registers */
+		       0xe0008300 0x8>;		/* config space access registers */
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
diff --git a/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt b/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt
new file mode 100644
index 000000000000..d015dcec4011
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt
@@ -0,0 +1,40 @@
+GPIO controllers on MPC8xxx SoCs
+
+This is for the non-QE/CPM/GUTs GPIO controllers as found on
+8349, 8572, 8610 and compatible.
+
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+
+Required properties:
+- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for
+  83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+ - interrupts : Interrupt mapping for GPIO IRQ (currently unused).
+ - interrupt-parent : Phandle for the interrupt controller that
+   services interrupts for this device.
+- gpio-controller : Marks the port as GPIO controller.
+
+Example of gpio-controller nodes for a MPC8347 SoC:
+
+	gpio1: gpio-controller@c00 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
+		reg = <0xc00 0x100>;
+		interrupts = <74 0x8>;
+		interrupt-parent = <&ipic>;
+		gpio-controller;
+	};
+
+	gpio2: gpio-controller@d00 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
+		reg = <0xd00 0x100>;
+		interrupts = <75 0x8>;
+		interrupt-parent = <&ipic>;
+		gpio-controller;
+	};
+
+See booting-without-of.txt for details of how to specify GPIO
+information for devices.
diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt
index 86826df00e64..cc453110fc46 100644
--- a/Documentation/powerpc/dts-bindings/fsl/dma.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/dma.txt
@@ -20,7 +20,7 @@ Required properties:
         - compatible        : compatible list, contains 2 entries, first is
 			 "fsl,CHIP-dma-channel", where CHIP is the processor
 			 (mpc8349, mpc8350, etc.) and the second is
-			 "fsl,elo-dma-channel"
+			 "fsl,elo-dma-channel". However, see note below.
         - reg               : <registers mapping for channel>
         - cell-index        : dma channel index starts at 0.
 
@@ -82,7 +82,7 @@ Required properties:
         - compatible        : compatible list, contains 2 entries, first is
 			 "fsl,CHIP-dma-channel", where CHIP is the processor
 			 (mpc8540, mpc8560, etc.) and the second is
-			 "fsl,eloplus-dma-channel"
+			 "fsl,eloplus-dma-channel". However, see note below.
         - cell-index        : dma channel index starts at 0.
         - reg               : <registers mapping for channel>
         - interrupts        : <interrupt mapping for DMA channel IRQ>
@@ -125,3 +125,12 @@ Example:
 			interrupts = <17 2>;
 		};
 	};
+
+Note on DMA channel compatible properties: The compatible property must say
+"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA
+driver (fsldma).  Any DMA channel used by fsldma cannot be used by another
+DMA driver, such as the SSI sound drivers for the MPC8610.  Therefore, any DMA
+channel that should be used for another driver should not use
+"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel".  For the SSI drivers, for
+example, the compatible property should be "fsl,ssi-dma-channel".  See ssi.txt
+for more information.
diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt
index d100555d488a..a2d963998a65 100644
--- a/Documentation/powerpc/dts-bindings/fsl/ssi.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/ssi.txt
@@ -24,6 +24,12 @@ Required properties:
 		    "rj-master" - r.j., SSI is clock master
 		    "ac97-slave" - AC97 mode, SSI is clock slave
 		    "ac97-master" - AC97 mode, SSI is clock master
+- fsl,playback-dma: phandle to a node for the DMA channel to use for
+                    playback of audio.  This is typically dictated by SOC
+                    design.  See the notes below.
+- fsl,capture-dma:  phandle to a node for the DMA channel to use for
+                    capture (recording) of audio.  This is typically dictated
+                    by SOC design.  See the notes below.
 
 Optional properties:
 - codec-handle	  : phandle to a 'codec' node that defines an audio
@@ -36,3 +42,20 @@ Child 'codec' node required properties:
 Child 'codec' node optional properties:
 - clock-frequency  : The frequency of the input clock, which typically
                      comes from an on-board dedicated oscillator.
+
+Notes on fsl,playback-dma and fsl,capture-dma:
+
+On SOCs that have an SSI, specific DMA channels are hard-wired for playback
+and capture.  On the MPC8610, for example, SSI1 must use DMA channel 0 for
+playback and DMA channel 1 for capture.  SSI2 must use DMA channel 2 for
+playback and DMA channel 3 for capture.  The developer can choose which
+DMA controller to use, but the channels themselves are hard-wired.  The
+purpose of these two properties is to represent this hardware design.
+
+The device tree nodes for the DMA channels that are referenced by
+"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
+"fsl,ssi-dma-channel".  The SOC-specific compatible string (e.g.
+"fsl,mpc8610-dma-channel") can remain.  If these nodes are left as
+"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
+drivers (fsldma) will attempt to use them, and it will conflict with the
+sound drivers.
diff --git a/Documentation/powerpc/ppc_htab.txt b/Documentation/powerpc/ppc_htab.txt
deleted file mode 100644
index 8b8c7df29fa9..000000000000
--- a/Documentation/powerpc/ppc_htab.txt
+++ /dev/null
@@ -1,118 +0,0 @@
-                 Information about /proc/ppc_htab
-=====================================================================
-
-This document and the related code was written by me (Cort Dougan), please
-email me (cort@fsmlabs.com) if you have questions, comments or corrections.
-
-Last Change: 2.16.98
-
-This entry in the proc directory is readable by all users but only
-writable by root.
-
-The ppc_htab interface is a user level way of accessing the
-performance monitoring registers as well as providing information
-about the PTE hash table.
-
-1. Reading
-
-  Reading this file will give you information about the memory management
-  hash table that serves as an extended tlb for page translation on the
-  powerpc.  It will also give you information about performance measurement
-  specific to the cpu that you are using.
-
-  Explanation of the 604 Performance Monitoring Fields:
-    MMCR0 - the current value of the MMCR0 register
-    PMC1
-    PMC2 - the value of the performance counters and a
-           description of what events they are counting
-           which are based on MMCR0 bit settings.
-  Explanation of the PTE Hash Table fields:
-
-    Size - hash table size in Kb.
-    Buckets -  number of buckets in the table.
-    Address - the virtual kernel address of the hash table base.
-    Entries - the number of ptes that can be stored in the hash table.
-    User/Kernel - how many pte's are in use by the kernel or user at that time.
-    Overflows - How many of the entries are in their secondary hash location.
-    Percent full - ratio of free pte entries to in use entries.
-    Reloads - Count of how many hash table misses have occurred
-              that were fixed with a reload from the linux tables.
-              Should always be 0 on 603 based machines.
-    Non-error Misses - Count of how many hash table misses have occurred
-              that were completed with the creation of a pte in the linux
-              tables with a call to do_page_fault().
-    Error Misses - Number of misses due to errors such as bad address
-              and permission violations.  This includes kernel access of
-              bad user addresses that are fixed up by the trap handler.
-
-  Note that calculation of the data displayed from /proc/ppc_htab takes
-  a long time and spends a great deal of time in the kernel.  It would
-  be quite hard on performance to read this file constantly.  In time
-  there may be a counter in the kernel that allows successive reads from
-  this file only after a given amount of time has passed to reduce the
-  possibility of a user slowing the system by reading this file.
-
-2. Writing
-
-  Writing to the ppc_htab allows you to change the characteristics of
-  the powerpc PTE hash table and setup performance monitoring.
-
-  Resizing the PTE hash table is not enabled right now due to many
-  complications with moving the hash table, rehashing the entries
-  and many many SMP issues that would have to be dealt with.
-
-  Write options to ppc_htab:
-  
-   - To set the size of the hash table to 64Kb:
-
-      echo 'size 64' > /proc/ppc_htab
-
-     The size must be a multiple of 64 and must be greater than or equal to
-     64.
-
-   - To turn off performance monitoring:
-
-      echo 'off' > /proc/ppc_htab
-
-   - To reset the counters without changing what they're counting:
-
-      echo 'reset' > /proc/ppc_htab
-
-     Note that counting will continue after the reset if it is enabled.
-
-   - To count only events in user mode or only in kernel mode:
-
-      echo 'user' > /proc/ppc_htab
-       ...or...
-      echo 'kernel' > /proc/ppc_htab
-
-     Note that these two options are exclusive of one another and the
-     lack of either of these options counts user and kernel.
-     Using 'reset' and 'off' reset these flags.
-
-   - The 604 has 2 performance counters which can each count events from
-     a specific set of events.  These sets are disjoint so it is not
-     possible to count _any_ combination of 2 events.  One event can
-     be counted by PMC1 and one by PMC2.
-
-     To start counting a particular event use:
-
-      echo 'event' > /proc/ppc_htab
-
-     and choose from these events:
-
-     PMC1
-     ----
-      'ic miss' - instruction cache misses
-      'dtlb' - data tlb misses (not hash table misses)
-
-     PMC2
-     ----
-      'dc miss' - data cache misses
-      'itlb' - instruction tlb misses (not hash table misses)
-      'load miss time' - cycles to complete a load miss
-
-3. Bugs
-
-  The PMC1 and PMC2 counters can overflow and give no indication of that
-  in /proc/ppc_htab.
diff --git a/Documentation/powerpc/smp.txt b/Documentation/powerpc/smp.txt
deleted file mode 100644
index 5b581b849ff7..000000000000
--- a/Documentation/powerpc/smp.txt
+++ /dev/null
@@ -1,34 +0,0 @@
-                 Information about Linux/PPC SMP mode
-=====================================================================
-
-This document and the related code was written by me
-(Cort Dougan, cort@fsmlabs.com) please email me if you have questions,
-comments or corrections.
-
-Last Change: 3.31.99
-
-If you want to help by writing code or testing different hardware please
-email me!
-
-1. State of Supported Hardware
-
-  PowerSurge Architecture - tested on UMAX s900, Apple 9600
-    The second processor on this machine boots up just fine and
-    enters its idle loop.  Hopefully a completely working SMP kernel
-    on this machine will be done shortly.
-
-    The code makes the assumption of only two processors.  The changes
-    necessary to work with any number would not be overly difficult but
-    I don't have any machines with >2 processors so it's not high on my
-    list of priorities.  If anyone else would like do to the work email
-    me and I can point out the places that need changed.  If you have >2
-    processors and don't want to add support yourself let me know and I
-    can take a look into it.
-
-  BeBox
-    BeBox support hasn't been added to the 2.1.X kernels from 2.0.X
-    but work is being done and SMP support for BeBox is in the works.
-
-  CHRP
-    CHRP SMP works and is fairly solid.  It's been tested on the IBM F50
-    with 4 processors for quite some time now.