Merge remote-tracking branch 'regulator/topic/max8997' into regulator-next

1 files changed, 146 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
new file mode 100644
index 000000000000..9fd69a18b0ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
@@ -0,0 +1,146 @@
+* Maxim MAX8997 Voltage and Current Regulator
+
+The Maxim MAX8997 is a multi-function device which includes volatage and
+current regulators, rtc, charger controller and other sub-blocks. It is
+interfaced to the host controller using a i2c interface. Each sub-block is
+addressed by the host system using different i2c slave address. This document
+describes the bindings for 'pmic' sub-block of max8997.
+
+Required properties:
+- compatible: Should be "maxim,max8997-pmic".
+- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
+
+- max8997,pmic-buck1-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck1 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+- max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck2 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+- max8997,pmic-buck5-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck5 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+[1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
+    property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage'
+    property should specify atleast one voltage level (which would be a
+    safe operating voltage).
+
+    If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
+    property is specified, then all the eigth voltage values for the
+    'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+  the interrupts from max8997 are delivered to.
+- interrupts: Interrupt specifiers for two interrupt sources.
+  - First interrupt specifier is for 'irq1' interrupt.
+  - Second interrupt specifier is for 'alert' interrupt.
+- max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs.
+- max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
+- max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs.
+
+Additional properties required if either of the optional properties are used:
+- max8997,pmic-ignore-gpiodvs-side-effect: When GPIO-DVS mode is used for
+  multiple bucks, changing the voltage value of one of the bucks may affect
+  that of another buck, which is the side effect of the change (set_voltage).
+  Use this property to ignore such side effects and change the voltage.
+
+- max8997,pmic-buck125-default-dvs-idx: Default voltage setting selected from
+  the possible 8 options selectable by the dvs gpios. The value of this
+  property should be between 0 and 7. If not specified or if out of range, the
+  default value of this property is set to 0.
+
+- max8997,pmic-buck125-dvs-gpios: GPIO specifiers for three host gpio's used
+  for dvs. The format of the gpio specifier depends in the gpio controller.
+
+Regulators: The regulators of max8997 that have to be instantiated should be
+included in a sub-node named 'regulators'. Regulator nodes included in this
+sub-node should be of the format as listed below.
+
+	regulator_name {
+		standard regulator bindings here
+	};
+
+The following are the names of the regulators that the max8997 pmic block
+supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of max8997.
+
+	- LDOn
+		  - valid values for n are 1 to 18 and 21
+		  - Example: LDO0, LD01, LDO2, LDO21
+	- BUCKn
+		  - valid values for n are 1 to 7.
+		  - Example: BUCK1, BUCK2, BUCK3, BUCK7
+
+	- ENVICHG: Battery Charging Current Monitor Output. This is a fixed
+		   voltage type regulator
+
+	- ESAFEOUT1: (ldo19)
+	- ESAFEOUT2: (ld020)
+
+	- CHARGER_CV: main battery charger voltage control
+	- CHARGER: main battery charger current control
+	- CHARGER_TOPOFF: end of charge current threshold level
+
+The bindings inside the regulator nodes use the standard regulator bindings
+which are documented elsewhere.
+
+Example:
+
+	max8997_pmic@66 {
+		compatible = "maxim,max8997-pmic";
+		interrupt-parent = <&wakeup_eint>;
+		reg = <0x66>;
+		interrupts = <4 0>, <3 0>;
+
+		max8997,pmic-buck1-uses-gpio-dvs;
+		max8997,pmic-buck2-uses-gpio-dvs;
+		max8997,pmic-buck5-uses-gpio-dvs;
+
+		max8997,pmic-ignore-gpiodvs-side-effect;
+		max8997,pmic-buck125-default-dvs-idx = <0>;
+
+		max8997,pmic-buck125-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
+						 <&gpx0 1 1 0 0>, /* SET2 */
+						 <&gpx0 2 1 0 0>; /* SET3 */
+
+		max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+						 <1250000>, <1200000>,
+						 <1150000>, <1100000>,
+						 <1000000>, <950000>;
+
+		max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>,
+						 <1100000>, <1100000>,
+						 <1000000>, <1000000>,
+						 <1000000>, <1000000>;
+
+		max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ABB_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_ARM_1.2V";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};