1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
Wolfson Arizona class audio SoCs
These devices are audio SoCs with extensive digital capabilites and a range
of analogue I/O.
Required properties:
- compatible : One of the following chip-specific strings:
"wlf,wm5102"
"wlf,wm5110"
"wlf,wm8280"
"wlf,wm8997"
- reg : I2C slave address when connected using I2C, chip select number when
using SPI.
- interrupts : The interrupt line the /IRQ signal for the device is
connected to.
- interrupt-controller : Arizona class devices contain interrupt controllers
and may provide interrupt services to other devices.
- interrupt-parent : The parent interrupt controller.
- #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
The first cell is the IRQ number.
The second cell is the flags, encoded as the trigger masks from
Documentation/devicetree/bindings/interrupts.txt
- gpio-controller : Indicates this device is a GPIO controller.
- #gpio-cells : Must be 2. The first cell is the pin number and the
second cell is used to specify optional parameters (currently unused).
- AVDD-supply, DBVDD1-supply, CPVDD-supply : Power supplies for the device,
as covered in Documentation/devicetree/bindings/regulator/regulator.txt
- DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102,
wm5110, wm8280)
- SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102,
wm5110, wm8280)
- SPKVDD-supply : Speaker driver power supply (wm8997)
Optional properties:
- wlf,reset : GPIO specifier for the GPIO controlling /RESET
- wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA
- wlf,gpio-defaults : A list of GPIO configuration register values. Defines
for the appropriate values can found in <dt-bindings/mfd/arizona.txt>. If
absent, no configuration of these registers is performed. If any entry has
a value that is out of range for a 16 bit register then the chip default
will be used. If present exactly five values must be specified.
- wlf,inmode : A list of INn_MODE register values, where n is the number
of input signals. Valid values are 0 (Differential), 1 (Single-ended) and
2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default.
If present, values must be specified less than or equal to the number of
input singals. If values less than the number of input signals, elements
that has not been specifed are set to 0 by default.
- wlf,dmic-ref : DMIC reference voltage source for each input, can be
selected from either MICVDD or one of the MICBIAS's, defines
(ARIZONA_DMIC_xxxx) are provided in <dt-bindings/mfd/arizona.txt>. If
present, the number of values should be less than or equal to the
number of inputs, unspecified inputs will use the chip default.
- wlf,hpdet-channel : Headphone detection channel.
ARIZONA_ACCDET_MODE_HPL or 1 - Headphone detect mode is set to HPDETL
ARIZONA_ACCDET_MODE_HPR or 2 - Headphone detect mode is set to HPDETR
If this node is not mentioned or if the value is unknown, then
headphone detection mode is set to HPDETL.
- DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if
they are being externally supplied. As covered in
Documentation/devicetree/bindings/regulator/regulator.txt
Optional subnodes:
- ldo1 : Initial data for the LDO1 regulator, as covered in
Documentation/devicetree/bindings/regulator/regulator.txt
- micvdd : Initial data for the MICVDD regulator, as covered in
Documentation/devicetree/bindings/regulator/regulator.txt
Example:
codec: wm5102@1a {
compatible = "wlf,wm5102";
reg = <0x1a>;
interrupts = <347>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&gic>;
gpio-controller;
#gpio-cells = <2>;
wlf,gpio-defaults = <
ARIZONA_GP_FN_TXLRCLK
ARIZONA_GP_DEFAULT
ARIZONA_GP_DEFAULT
ARIZONA_GP_DEFAULT
ARIZONA_GP_DEFAULT
>;
};
|
