1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
Mediatek HDMI Encoder
=====================
The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
its parallel input.
Required properties:
- compatible: Should be "mediatek,<chip>-hdmi".
- reg: Physical base address and length of the controller's registers
- interrupts: The interrupt signal from the function block.
- clocks: device clocks
See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
- phys: phandle link to the HDMI PHY node.
See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
- phy-names: must contain "hdmi"
- mediatek,syscon-hdmi: phandle link and register offset to the system
configuration registers. For mt8173 this must be offset 0x900 into the
MMSYS_CONFIG region: <&mmsys 0x900>.
- ports: A node containing input and output port nodes with endpoint
definitions as documented in Documentation/devicetree/bindings/graph.txt.
- port@0: The input port in the ports node should be connected to a DPI output
port.
- port@1: The output port in the ports node should be connected to the input
port of a connector node that contains a ddc-i2c-bus property, or to the
input port of an attached bridge chip, such as a SlimPort transmitter.
HDMI CEC
========
The HDMI CEC controller handles hotplug detection and CEC communication.
Required properties:
- compatible: Should be "mediatek,<chip>-cec"
- reg: Physical base address and length of the controller's registers
- interrupts: The interrupt signal from the function block.
- clocks: device clock
HDMI DDC
========
The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
The Mediatek's I2C controller is used to interface with I2C devices.
Required properties:
- compatible: Should be "mediatek,<chip>-hdmi-ddc"
- reg: Physical base address and length of the controller's registers
- clocks: device clock
- clock-names: Should be "ddc-i2c".
HDMI PHY
========
The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
output and drives the HDMI pads.
Required properties:
- compatible: "mediatek,<chip>-hdmi-phy"
- reg: Physical base address and length of the module's registers
- clocks: PLL reference clock
- clock-names: must contain "pll_ref"
- clock-output-names: must be "hdmitx_dig_cts" on mt8173
- #phy-cells: must be <0>
- #clock-cells: must be <0>
Optional properties:
- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
Example:
cec: cec@10013000 {
compatible = "mediatek,mt8173-cec";
reg = <0 0x10013000 0 0xbc>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
clocks = <&infracfg CLK_INFRA_CEC>;
};
hdmi_phy: hdmi-phy@10209100 {
compatible = "mediatek,mt8173-hdmi-phy";
reg = <0 0x10209100 0 0x24>;
clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
clock-names = "pll_ref";
clock-output-names = "hdmitx_dig_cts";
mediatek,ibias = <0xa>;
mediatek,ibias_up = <0x1c>;
#clock-cells = <0>;
#phy-cells = <0>;
};
hdmi_ddc0: i2c@11012000 {
compatible = "mediatek,mt8173-hdmi-ddc";
reg = <0 0x11012000 0 0x1c>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
clocks = <&pericfg CLK_PERI_I2C5>;
clock-names = "ddc-i2c";
};
hdmi0: hdmi@14025000 {
compatible = "mediatek,mt8173-hdmi";
reg = <0 0x14025000 0 0x400>;
interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
<&mmsys CLK_MM_HDMI_PLLCK>,
<&mmsys CLK_MM_HDMI_AUDIO>,
<&mmsys CLK_MM_HDMI_SPDIF>;
clock-names = "pixel", "pll", "bclk", "spdif";
pinctrl-names = "default";
pinctrl-0 = <&hdmi_pin>;
phys = <&hdmi_phy>;
phy-names = "hdmi";
mediatek,syscon-hdmi = <&mmsys 0x900>;
assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
assigned-clock-parents = <&hdmi_phy>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
hdmi0_in: endpoint {
remote-endpoint = <&dpi0_out>;
};
};
port@1 {
reg = <1>;
hdmi0_out: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
};
};
connector {
compatible = "hdmi-connector";
type = "a";
ddc-i2c-bus = <&hdmiddc0>;
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi0_out>;
};
};
};
|
