| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For SDIO the alignment requirement for transfers from device to host
is configured in firmware. This configuration is limited to minimum
of 4-byte alignment. However, this is not correct for platforms using
64-bit DMA when the minimum alignment should be 8 bytes. This issue
appeared when the ALIGNMENT definition was set according the DMA
configuration. The configuration in firmware was not using that macro
defintion, but a hardcoded value of 4. Hence the driver reported
alignment failures for data coming from the device and causing
transfers to fail.
Fixes: 6e84ab604bde ("brcmfmac: properly align buffers on certain platforms
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of patches for -next:
* API support for concurrent scheduled scan requests
* API changes for roaming reporting
* BSS max idle support in mac80211
* API changes for TX status reporting in mac80211
* API changes for RX rate reporting in mac80211
* rewrite monitor logic to prepare for BPF filters
* bugfix for rare devices without 2.4 GHz support
* a bugfix for recent DFS changes
* some further cleanups
The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.
Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver was making changes to the skb_header without
ensuring it was writable (i.e. uncloned).
This patch also removes some boiler plate header size
checking/adjustment code as that is also handled by the
skb_cow_header function used to make header writable.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The incoming skb header may be resized if header space is
insufficient, which might change the data adddress in the skb.
Ensure that a cached pointer to that data is correctly set by
moving assignment to after any possible changes.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fwsignal module is only referenced by the bcdc module and part of the
bcdc protocol. So only build it when CONFIG_BRCMFMAC_PROTO_BCDC is selected.
Fixes: acf8ac41dd73 ("brcmfmac: remove reference to fwsignal data from struct brcmf_pub")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When receiving pno results there may be duplicate channels and/or
ssids. Assure each is added only once when preparing the internal
escan request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Checking whether the address of an array element is null is bogus
so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Assure the event data buffer is long enough to hold the array
of netinfo items and that SSID length does not exceed the maximum
of 32 characters as per 802.11 spec.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The fwsignal module is part of the bcdc protocol and as such does
its instance data is not needed in core structure. Moving it into
struct brcmf_bcdc instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc
field is initialized regardless the state of the fwsignal functionality,
ie. the fcmode. This is not needed when fcmode is NONE, which is the
default mode.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a non-functional change to align the fwsignal module to
the naming pattern used throughout the driver.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Systems with 64 bit DMA at least partially require buffers to be used
for DMA to be 8-byte-aligned. One example is Amlogic Meson GX.
Switching the MMC/SDIO driver for this platform to SG DMA mode
resulted in problems due to unaligned buffers.
Fortunately the brcmfmac driver has a global define for the alignment.
Changing it to 8 fixed the issues with Meson GX.
Suggested-by: Helmut Klein <hgkr.klein@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In brcmf_pno_start_sched_scan() a local variable is declared and
assigned for struct brcmu_d11inf. However, there is no other reference
to it so it is unnecessary.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In brcmf_pcie_suspend() we inform the firmware on the device that
it will enter in D3 state. Before this is done we already bring down
the bus state. However, When entering D3 fails we abort the suspend
and the bus state need to be restored.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
To support network namespace the driver must assure all created
network interfaces are in the same namespace as the wiphy instance
and flag the support using WIPHY_FLAG_NETNS_OK.
Verified using two terminals:
Terminal 1 Terminal 2
-------------------------- ---------------------------------
# ip netns add brcm-wifi # iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x1
# ip netns exec brcm-wifi bash
# iw dev
# echo $$
20337 # iw phy0 set netns 20337
# iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x2
# iw phy0 interface add wl3.ap type __ap
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x3
Interface wlan3
ifindex 11
wdev 0x2
# iw dev
# iw phy0 set netns 1
# iw dev
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x5
Interface wlan3
ifindex 11
wdev 0x4
Note:
increasing wdev identifier above indicates issue in
cfg80211 which is addressed separately.
Tested-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move brcmf_fws_deinit into brcmf_proto_bcdc_detach since it is a bcdc
exclusive feature.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Create a new protocol layer interface brcmf_proto_init_cb for protocol
layer to finish initialzation after core module components(fweh and
etc.) are initialized.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* an RCU fix
* a fix for a potential out-of-bounds access crash
* a fix for IBSS which has been broken since DQA was enabled
rtlwifi
* fix scheduling while atomic regression
brcmfmac
* fix use-after-free bug found by KASAN
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).
That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A use-after-free was found using KASAN. In brcmf_p2p_del_if() the virtual
interface is removed using call to brcmf_remove_interface(). After that
the virtual interface instance has been freed and should not be referenced.
Solve this by storing the nl80211 iftype in local variable, which is used
in a couple of places anyway.
Cc: stable@vger.kernel.org # 4.10.x, 4.9.x
Reported-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Create a new protocol interface function brcmf_proto_reset_if for core
module to notify protocol layer when interface role changes.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Create a new protocol interface function brcmf_proto_del_if for core
module to notify protocol layer upon interface deletion.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
fwsignal is only used by bcdc. Create a new protocol interface function
brcmf_proto_add_if for core module to notify protocol layer upon a new
interface is created.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
brcmf_txcomplete is invoked by sdio and usb bus module which are using
bcdc protocol. So move it from core module into bcdc layer.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
brcmf_txflowblock is invoked by sdio and usb bus module which are using
bcdc protocol. This patch makes it a bcdc API instead of a core module
function.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If a scan gets aborted BRCMF_SCAN_STATUS_BUSY gets cleared in
cfg->scan_status and when we receive an abort event from the firmware
the BRCMF_SCAN_STATUS_BUSY check in the cfg80211_escan_handler will
trigger resulting in multiple errors getting logged.
Check for a status of BRCMF_E_STATUS_ABORT and in this case simply
cleanly exit the cfg80211_escan_handler. This also avoids a
BRCMF_E_STATUS_ABORT event arriving after a new scan has been started
causing the new scan to complete prematurely without any data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The country code gets set to "00" by default at boot, ignore this
rather then logging an error about it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Using pr_err for things which are not errors is a bad idea. E.g. it
will cause the plymouth bootsplash screen to drop back to the text
console so that the user can see the error, which is not what we
normally want to happen.
Instead add a new brcmf_info macro and use that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
So far we were attaching BRCMF_E_PSM_WATCHDOG event listener in
brcmf_debug_attach which gets compiled only with CONFIG_BRCMDBG. This
event means something went wrong and firmware / hardware usually can't
be expected to work (reliably).
Such a problem is significant for user experience so I believe we should
print an error unconditionally (even with debugging disabled). What can
be indeed optional is dumping bus memory as this is clearly part of
debugging process.
In the future we may also try to extend this listener by trying to
recover from the error or at least signal it to the cfg80211.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
<linux/sched/signal.h>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Instead of using a private copy of struct net_device_stats in struct
brcm_if, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Now we always have __brcmf_err function we can do perfectly fine with
just one macro.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This will allow extending code and using more detailed messages e.g.
with the help of dev_err.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This allows simplifying the code by adding a simple IS_ENABLED check for
CONFIG_BRCMDB symbol.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This new helper reads extra frequency limits specified in DT and
disables unavailable chanels. This is useful for devices (like home
routers) with chipsets limited e.g. by board design.
In order to respect info read from DT we simply need to check for
IEEE80211_CHAN_DISABLED bit when constructing channel info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It's important to inform user so he knows things went wrong. He may also
want to get memory dump for further debugging purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This method may be unsupported (see: USB bus) or may just fail (see:
SDIO bus).
While at it rework logic in brcmf_sdio_bus_get_memdump function to avoid
too many conditional code nesting levels.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for the .update_connect_params() callback for roaming
or subsequent (re)association.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The wowlan support is (partially) determined dynamic by checking the
device/firmware capabilities. So they can differ per device. So it
is not possible to use a static global. Instead use the global as a
template and use kmemdup(). When kmemdup() fails the template is used
unmodified.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For wowl netdetect the event data changed for newer chips. This
was recently fixed for scheduled scan, but same change is needed
for wowl netdetect. Removing now pointles += operation from both
result handlers.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
