| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Should help debug strange tx lockup type issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Previous code left it NULL.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I thought this might help track down stuck queues, etc.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are several places where ath_reset() was called without proper
calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls
directly to ath_reset and drop them from callers where it makes sense.
Also add them to the config callback around ath_update_txpow to fix a
crash that happens when the tx power changed before any vif is brought up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.
Cc: stable@kernel.org
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
|
|
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered. Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.
In addtion, use the vif type instead of hardware opmode
when dealing with beacons.
Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Because the sendbar variable was not reset to zero, the stack would send
Block ACK requests for all subframes following the one that failed, which
could mess up the receiver side block ack window.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Sometimes the first TID in the first AC's list is not available for forming
a new aggregate (the BAW might not allow it), however other TIDs may have
data available for sending.
Prevent a slowdown of other TIDs by going through multiple entries until
we've either hit the last one or enough AMPDUs are pending in the hardware
queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9285 carrier leakage calibration related workaround on high
temperature is not applicable for AR9271.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ath9k_hw assumes that caldata is valid only for
oper channel. But with ath9k_htc case, the caldata is
passed for all channels on hw_reset though we are not doing
calibration on that channel. So the oper channel's nf history
got cleared to default due to mismatch in channel flags.
This patch also saves some space.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
caldata's channel info is never filled with operating channel
info which is causing the operating channel's noise floor
history buffer is reset to default nf during channel change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The rx error bit parsing was changed to consider PHY errors and various
decryption errors separately. While correct according to the documentation,
this is causing spurious decryption error reports in some situations.
Fix this by restoring the original order of the checks in those places,
where the errors are meant to be mutually exclusive.
If a CRC error is reported, then MIC failure and decryption errors
are irrelevant, and a PHY error is unlikely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Eeprom read functions are of bool type and not int.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since baseband hangs are rare, but the hang check function has a high
false positive rate in some situations, we need to add more reliable
indicators.
In AP mode we can use blocked beacon transmissions as an indicator,
they should be rare enough.
In station mode, we can skip the hang check entirely, since a true
hang will trigger beacon loss detection, and mac80211 will rescan,
which leads to a hw reset that will bring the hardware back to life.
To make this more reliable, we need to skip fast channel changes
if the hardware appears to be stuck.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There might be some old stale data left, which could confuse tracking
of pending tx frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
txtid->seq_start may not always be up to date, when there is HT non-AMPDU
traffic just before starting an AMPDU session. Relying on txtid->seq_next
is better, since it is also used to generate the sequence numbers for
all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When a tid pointer is passed to ath_tx_send_normal(), it increases the
starting sequence number for the next AMPDU action frame, which should
only be done if the sequence number assignment is fresh. In this case
it is clearly not.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For USB devices, reading the EEPROM data can be offloaded
to the target. Use multiple register reads to take advantage
of this feature to reduce initialization time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This would decrease latency in reading bulk registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath5k_reset must be called with sc->lock. Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.
Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
|
The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.
Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
USB devices do not require the chip test routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
net/bluetooth/Makefile
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To inject a packet in monitor mode, a dummy station has
to be associated with the monitor interface in the target.
Failing to do this would result in a firmware crash on the device.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing
the result in "ee_mode" which is an unsigned char. This breaks the
error handling. This patch makes "ee_mode" an int.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove some obvious looking dead code and rename few functions
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit 0ce3bcfc84900a64347b0fe1140229bd81314008.
Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period
Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
And add the copyright/license header.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().
This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.
Cc: stable <stable@kernel.org>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch revamps some common code-paths which are
shared between (re-)initialization and suspend/resume
subroutines. It also adds some helpful comments
about quirks and associated difficulties.
It's quite big, but it should fix #25382:
<https://bugzilla.kernel.org/show_bug.cgi?id=25382>
And hopefully the code is robust enough to deal with
all possible suspend/resume scenarios without requiring
the user to do any sort of manual and possibly
dangerous work.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
By removing two "safety" msleeps (and an echo nop), the
channel change delay is effectively halved. Previously,
the delay could be as long as 260 ms and the device
could not go off-channel without risking to miss the
next DTIM beacon [interval ~307 ms].
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
