| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The hardware specific function adf_get_arbiter_mapping() modifies
the static array thrd_to_arb_map to disable mappings for AEs
that are disabled. This static array is used for each device
of the same type. If the ae mask is not identical for all devices
of the same type then the arbiter mapping returned by
adf_get_arbiter_mapping() may be wrong.
This patch fixes this problem by ensuring the static arbiter
mapping is unchanged and the device arbiter mapping is re-calculated
each time based on the static mapping.
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Abstract writes to the service arbiter enable register.
This is in preparation for the introduction of the qat_4xxx driver since
the arbitration enable register differes between QAT GEN2 and QAT GEN4
devices.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Maksim Lukoshkov <maksim.lukoshkov@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Enable arbitration on the TX ring only after the RX ring is programmed.
Before this change, arbitration was enabled on the TX ring before the RX
ring was programmed allowing the HW to process a request before having
the ring pair configured.
With this change, the arbitration logic is programmed only if the TX
half of the ring mask matches the RX half.
This change does not affect QAT GEN2 devices (c62x, c3xxx and dh895xcc),
but it is a must for QAT GEN4 devices since the CSRs of the ring pair
are locked after arbitration is enabled on the TX ring.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Maksim Lukoshkov <maksim.lukoshkov@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The arbiter configuration, the offset to the arbiter config CSR and the
offset to the worker thread to service arbiter CSR are going to be
different in QAT GEN4 devices although the logic that uses them is the
same across all QAT generations.
This patch reworks the gen-specific parts of the arbiter access code by
introducing the arb_info structure, that contains the values that are
generation specific, and a function in the structure adf_hw_device_data,
get_arb_info(), that allows to get them.
Since the arbiter values for QAT GEN2 devices (c62x, c3xxx and
dh895xcc) are the same, a single function, adf_gen2_get_arb_info() is
provided in adf_gen2_hw_data.c and referenced by each QAT GEN2 driver.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove the unused macros ADF_ARB_WTR_SIZE, ADF_ARB_WTR_OFFSET
and ADF_ARB_RO_EN_OFFSET.
These macros were left in commit 34074205bb9f ("crypto: qat - remove
redundant arbiter configuration") that removed the logic that used those
defines.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
WQCFG registers contain the correct values after reset in all
generations of QAT. No need to write into them.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Replace License Headers with SPDX License Identifiers.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The default arbiter configuration for ring weights and response ordering
is exactly what we want so we don't need to configure anything more.
This will also fix the problem where number of bundles is different
between different devices.
Reported-by: Ahsan Atta <ahsan.atta@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Move qat_isr.c and qat_isrvf.c files to qat_common dir
so that they can be reused by all devices.
Remove adf_drv.h files because thay are not longer needed.
Move adf_dev_configure() function to qat_common so it can be reused.
Also some minor updates to common code for multidevice.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Adf admin and HW arbiter function can be used by dh895xcc specific code
well as the new dh895xccvf and future devices so moving them to
qat_common so that they can be shared.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
