summaryrefslogtreecommitdiff
path: root/arch/arm/mach-at91/at91cap9_devices.c
AgeCommit message (Collapse)AuthorFilesLines
2012-02-03ARM: at91: code removal of CAP9 SoCJean-Christophe PLAGNIOL-VILLARD1-1273/+0
Following removal announce and addition to feature-removal-schedule.txt, here is the actual source code deletion for Atmel CAP9 family. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2011-11-29ARM: at91/soc: use gpio_is_valid to check the gpioJean-Christophe PLAGNIOL-VILLARD1-10/+10
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2011-11-29Merge branch 'drivers/macb-gem-cleanup' into at91/gpioArnd Bergmann1-3/+3
2011-11-28ARM: at91: make DBGU soc independentJean-Christophe PLAGNIOL-VILLARD1-2/+2
we will select now the DBGU used by the soc at Kconfig level For the DEBUG_LL and early_printk this will allow to select which DBGU to use this will also allow to select them when multiple SOC are enabled Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2011-11-28ARM: at91: make watchdog drivers soc independentJean-Christophe PLAGNIOL-VILLARD1-1/+10
switch the watchdog drivers to resource and pass it via platform_device Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2011-11-28ARM: at91: make rtt register base soc independantJean-Christophe PLAGNIOL-VILLARD1-2/+2
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2011-11-28ARM: at91: make ecc register base soc independantJean-Christophe PLAGNIOL-VILLARD1-2/+2
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2011-11-22macb: unify at91 and avr32 platform dataJamie Iles1-3/+3
Both at91 and avr32 defines its own platform data structure for the macb driver and both share common structures though at91 includes a currently unused phy_irq_pin. Create a common macb_platform_data for macb that both at91 and avr32 can use. In future we can use this to support other architectures that use the same IP block with the macb driver. v2: rename eth_platform_data to macb_platform_data and allow at91_ether to share the platform data with macb. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2011-11-09ARM: at91: Fix USBA gadget registrationJochen Friedrich1-1/+1
Since 193ab2a6070039e7ee2b9b9bebea754a7c52fd1b, various AT91 boards don't register USBA adapters anymore due to depending on a now non-existing symbol. Fix the symbol name. Signed-off-by: Jochen Friedrich <jochen@scram.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> CC: stable@kernel.org Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2011-11-09ARM: at91: usart: drop static map regs for dbguJean-Christophe PLAGNIOL-VILLARD1-3/+2
In commit fb149f9e28354 we introduce ioremap support for static map_io, we do not need this register entry anymore. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2011-11-01Merge branch 'depends/rmk/gpio' into next/develArnd Bergmann1-1/+1
Conflicts: arch/arm/mach-mxs/include/mach/gpio.h arch/arm/plat-mxc/include/mach/gpio.h Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-09-11at91: at91-ohci: configure overcurrent pins as input GPIOsThomas Petazzoni1-0/+6
As a new overcurrent_pin[] array has been added to the at91_usbh_data structure, those pins must be muxed to work properly. This commit implements this muxing for all AT91 SoCs that support the AT91 OHCI. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> [nicolas.ferre@atmel.com: added i variable declaration for the loop] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2011-08-08ARM: gpio: convert includes of mach/gpio.h and asm/gpio.h to linux/gpio.hRussell King1-1/+1
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h before we start consolidating the individual platform implementations of the gpio header files. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-06-25at91: fix at91_set_serial_console: use platform device idJean-Christophe PLAGNIOL-VILLARD1-1/+1
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2011-05-25at91: switch to CLKDEV_LOOKUPJean-Christophe PLAGNIOL-VILLARD1-17/+3
we do not change the clock naming convention so does not need to switch the AVR32 yet Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
2011-05-25atmel_serial: keep the platform_device unchangedJean-Christophe PLAGNIOL-VILLARD1-1/+3
specify the port num via platform_data this will allow to match the clock with the plaform_dev staticaly Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Alan Cox <alan@linux.intel.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-26Merge branch 'master' into for-nextJiri Kosina1-3/+3
Fast-forwarded to current state of Linus' tree as there are patches to be applied for files that didn't exist on the old branch.
2011-04-10treewide: remove extra semicolonsJustin P. Mattock1-1/+1
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-03-29arm: Cleanup the irq namespaceThomas Gleixner1-3/+3
Convert to the new function names. Automated with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2009-09-22ARM: 5719/1: [AT91] Fix AC97 breakageAndrew Victor1-5/+5
Fix AC97 build breakage with converting to the shared AT91/AVR32 AC97 driver: struct atmel_ac97_data -> struct ac97c_platform_data CONFIG_SND_AT91_AC97 -> CONFIG_SND_ATMEL_AC97C Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-14[ARM] 5390/1: AT91: Watchdog fixesAndrew Victor1-1/+1
The recently merged AT91SAM9 watchdog driver uses the AT91SAM9X_WATCHDOG config variable, whereas the original version of the driver (and the platform support code) used AT91SAM9_WATCHDOG. This causes the watchdog platform_device to never be registered, and therefore the driver not to be initialized. This patch: - updates the platform support code to use AT91SAM9X_WATCHDOG. - includes <linux/io.h> to fix compile error (same fix as was applied to at91rm9200_wdt.c) - fixes comment regarding watchdog clock-rates in at91rm9200. Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01[ARM] 5319/1: AT91: support AT91CAP9 revC CPUsStelian Pop1-2/+15
The AT91CAP9 revC CPU has a few differences over the previous, revB CPU which was distributed in small quantities only (revA was an internal Atmel product only). This patch adds the detection routines to recognize the different AT91CAP9 revisions (based on the PMC subsystem version number), and uses them to: - activate a workaround for the external interrupts levels (on revB CPUs) - set the UDPHS_BYPASS bit (on revB CPUs) - set AT91_GPBR register address to the correct offset (0xfffffd50 on revB, 0xfffffd60 on revC) For debugging usage, the CPU revision can be found in /proc/cpuinfo on the 'Revision' line. This patch is extracted from Andrew Victor's -at91 patch (2.6.27-at91.patch) where it has been tested for the last 6 months. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01[ARM] 5288/1: [AT91] Remove SMC configuration from devices.c filesAndrew Victor1-17/+2
In at91_add_device_nand(), do not configure the Static Memory controller with specific timing values. The *_devices.c files are board independent, and the SMC timing values are specific to the NAND devices that are installed on the board. The board-specific files are now responsible for configuring the Static Memory controller (if the don't want to leave it up to a bootloader). Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-22[ARM] 5258/1: [AT91] PWM controller initializationAndrew Victor1-0/+54
Add platform_devices and configuration of the PWM controller found on Atmel AT91CAP9, SAM9263 and SAM9RL processors. SAM9263 support by Sedji Gaouaou. Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/machRussell King1-5/+5
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-01Fix rename of at91_nand -> atmel_nandPieter du Preez1-1/+1
Structs called at91_nand_data where renamed to atmel_nand_data and configs called *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL*. This was unfortunately not done consistently, causing NAND chips not being initialised on several ARM boards. I am aware that the author of the original change did not rename MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example. All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order to keep naming consistency. This patch was only tested on a MACH_SAM9_L9260, as this is the only ARM board I have to my disposal. Before this patch: $ git-ls-files |xargs grep atmel_nand |wc -l 105 $ git-ls-files |xargs grep at91_nand |wc -l 4 $ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l 8 $ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l 47 After this patch: $ git-ls-files |xargs grep atmel_nand |wc -l 109 $ git-ls-files |xargs grep at91_nand |wc -l 0 $ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l 55 $ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l 0 Signed-off-by: Pieter du Preez <pdupreez@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-25Merge branch 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6David Woodhouse1-0/+99
2008-06-07[MTD] [NAND] rename at91_nand -> atmel_nand: internal symbolsHåvard Skinnemoen1-4/+4
This is basically s/at91_nand/atmel_nand/g with some manual inspection. Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-06-02[ARM] 4934/1: AT91CAP9 UDPHS driver: board and cpu integration.Stelian Pop1-0/+99
This is patch 2 of 2 adding support for the USB High Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP as the AVR32 and the AT91SAM9RL. This patch declares the UDPHS ressources in the at91cap9 (cpu and adk board) files, wires up the atmel_usba_udc driver to them, and activates the driver in the defconfig. Signed-off-by: Stelian Pop <stelian@popies.net> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-28[ARM] 5016/1: AT91: typo in mci configuration for at91cap at91sam9263Nicolas Ferre1-1/+1
typo in mci configuration in devices files Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17[ARM] 4982/1: [AT91] Drop old-style UART initialization (Part 1)Andrew Victor1-4/+6
All the SAM9 boards supported by mainline and the AT91 patches have been converted to the new-style UART initialization. Therefore drop support for the old at91_init_serial() interface for SAM9. at91_uarts[] array can also be marked as __initdata. The warning that no serial-console is defined moved from at91_set_serial_console() to at91_add_device_serial() since the whole point is the board-specific file is not calling at91_set_serial_console(). Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-04[ARM] 4909/1: [AT91] Timer/Counter Block platform_devicesAndrew Victor1-0/+38
Register platform_devices for the Timer/Counter Block peripherals found on the AT91RM9200, SAM9 & CAP9 processors. Original patch from David Brownell. Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-04[ARM] 4908/1: [AT91] RTT platform_device fixAndrew Victor1-2/+11
The RTT-as-RTC driver will search for the user-specified RTT peripheral via ID number (0 .. 1). Therefore if the processor only contains a single RTT peripheral, we need to set its platform_device.id to "0" instead of "-1". Also add the missing platform_device resource for the CAP9 processor. Bug reported by Sedji Gaouaou. Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-04[ARM] 4904/1: [AT91] Pass ECC controller to NAND driverAndrew Victor1-1/+6
On AT91 processors that include an ECC controller, pass its base address to the NAND driver via platform_device resources. Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-04[ARM] 4902/1: [AT91] SAM9/CAP9 memory controller headerAndrew Victor1-1/+1
The AT91CAP9 processor includes the same Static Memory Controller (SMC) peripheral as the SAM9 processors, but replaces the SDRAM Controller with a DDR/SDR Controller (DDRSDRC). This patch splits the existing include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and at91sam9_smc.h. It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller. Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26[ARM] 4764/1: [AT91] AT91CAP9 core supportAndrew Victor1-0/+1066
Add support for Atmel's AT91CAP9 Customizable Microcontroller family. <http://www.atmel.com/products/AT91CAP/Default.asp> Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-02 05:00:07 +0300