diff options
Diffstat (limited to 'drivers/tty/serial')
57 files changed, 2680 insertions, 2661 deletions
diff --git a/drivers/tty/serial/68328serial.c b/drivers/tty/serial/68328serial.c deleted file mode 100644 index 0982c1a44187..000000000000 --- a/drivers/tty/serial/68328serial.c +++ /dev/null @@ -1,1322 +0,0 @@ -/* 68328serial.c: Serial port driver for 68328 microcontroller - * - * Copyright (C) 1995 David S. Miller <davem@caip.rutgers.edu> - * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com> - * Copyright (C) 1998, 1999 D. Jeff Dionne <jeff@uclinux.org> - * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com> - * Copyright (C) 2002-2003 David McCullough <davidm@snapgear.com> - * Copyright (C) 2002 Greg Ungerer <gerg@snapgear.com> - * - * VZ Support/Fixes Evan Stawnyczy <e@lineo.ca> - * Multiple UART support Daniel Potts <danielp@cse.unsw.edu.au> - * Power management support Daniel Potts <danielp@cse.unsw.edu.au> - * VZ Second Serial Port enable Phil Wilshire - * 2.4/2.5 port David McCullough - */ - -#include <linux/module.h> -#include <linux/errno.h> -#include <linux/serial.h> -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/timer.h> -#include <linux/interrupt.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/major.h> -#include <linux/string.h> -#include <linux/fcntl.h> -#include <linux/mm.h> -#include <linux/kernel.h> -#include <linux/console.h> -#include <linux/reboot.h> -#include <linux/keyboard.h> -#include <linux/init.h> -#include <linux/pm.h> -#include <linux/bitops.h> -#include <linux/delay.h> -#include <linux/gfp.h> - -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/delay.h> -#include <asm/uaccess.h> - -/* (es) */ -/* note: perhaps we can murge these files, so that you can just - * define 1 of them, and they can sort that out for themselves - */ -#if defined(CONFIG_M68EZ328) -#include <asm/MC68EZ328.h> -#else -#if defined(CONFIG_M68VZ328) -#include <asm/MC68VZ328.h> -#else -#include <asm/MC68328.h> -#endif /* CONFIG_M68VZ328 */ -#endif /* CONFIG_M68EZ328 */ - -/* Turn off usage of real serial interrupt code, to "support" Copilot */ -#ifdef CONFIG_XCOPILOT_BUGS -#undef USE_INTS -#else -#define USE_INTS -#endif - -/* - * I believe this is the optimal setting that reduces the number of interrupts. - * At high speeds the output might become a little "bursted" (use USTCNT_TXHE - * if that bothers you), but in most cases it will not, since we try to - * transmit characters every time rs_interrupt is called. Thus, quite often - * you'll see that a receive interrupt occures before the transmit one. - * -- Vladimir Gurevich - */ -#define USTCNT_TX_INTR_MASK (USTCNT_TXEE) - -/* - * 68328 and 68EZ328 UARTS are a little bit different. EZ328 has special - * "Old data interrupt" which occures whenever the data stay in the FIFO - * longer than 30 bits time. This allows us to use FIFO without compromising - * latency. '328 does not have this feature and without the real 328-based - * board I would assume that RXRE is the safest setting. - * - * For EZ328 I use RXHE (Half empty) interrupt to reduce the number of - * interrupts. RXFE (receive queue full) causes the system to lose data - * at least at 115200 baud - * - * If your board is busy doing other stuff, you might consider to use - * RXRE (data ready intrrupt) instead. - * - * The other option is to make these INTR masks run-time configurable, so - * that people can dynamically adapt them according to the current usage. - * -- Vladimir Gurevich - */ - -/* (es) */ -#if defined(CONFIG_M68EZ328) || defined(CONFIG_M68VZ328) -#define USTCNT_RX_INTR_MASK (USTCNT_RXHE | USTCNT_ODEN) -#elif defined(CONFIG_M68328) -#define USTCNT_RX_INTR_MASK (USTCNT_RXRE) -#else -#error Please, define the Rx interrupt events for your CPU -#endif -/* (/es) */ - -/* - * This is our internal structure for each serial port's state. - */ -struct m68k_serial { - struct tty_port tport; - char is_cons; /* Is this our console. */ - int magic; - int baud_base; - int port; - int irq; - int type; /* UART type */ - int custom_divisor; - int x_char; /* xon/xoff character */ - int line; - unsigned char *xmit_buf; - int xmit_head; - int xmit_tail; - int xmit_cnt; -}; - -#define SERIAL_MAGIC 0x5301 - -/* - * Define the number of ports supported and their irqs. - */ -#define NR_PORTS 1 - -static struct m68k_serial m68k_soft[NR_PORTS]; - -static unsigned int uart_irqs[NR_PORTS] = { UART_IRQ_NUM }; - -/* multiple ports are contiguous in memory */ -m68328_uart *uart_addr = (m68328_uart *)USTCNT_ADDR; - -struct tty_driver *serial_driver; - -static void change_speed(struct m68k_serial *info, struct tty_struct *tty); - -/* - * Setup for console. Argument comes from the boot command line. - */ - -/* note: this is messy, but it works, again, perhaps defined somewhere else?*/ -#ifdef CONFIG_M68VZ328 -#define CONSOLE_BAUD_RATE 19200 -#define DEFAULT_CBAUD B19200 -#endif - - -#ifndef CONSOLE_BAUD_RATE -#define CONSOLE_BAUD_RATE 9600 -#define DEFAULT_CBAUD B9600 -#endif - - -static int m68328_console_initted; -static int m68328_console_baud = CONSOLE_BAUD_RATE; -static int m68328_console_cbaud = DEFAULT_CBAUD; - - -static inline int serial_paranoia_check(struct m68k_serial *info, - char *name, const char *routine) -{ -#ifdef SERIAL_PARANOIA_CHECK - static const char *badmagic = - "Warning: bad magic number for serial struct %s in %s\n"; - static const char *badinfo = - "Warning: null m68k_serial for %s in %s\n"; - - if (!info) { - printk(badinfo, name, routine); - return 1; - } - if (info->magic != SERIAL_MAGIC) { - printk(badmagic, name, routine); - return 1; - } -#endif - return 0; -} - -/* - * This is used to figure out the divisor speeds and the timeouts - */ -static int baud_table[] = { - 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800, - 9600, 19200, 38400, 57600, 115200, 0 }; - -/* Utility routines */ -static inline int get_baud(struct m68k_serial *ss) -{ - unsigned long result = 115200; - unsigned short int baud = uart_addr[ss->line].ubaud; - if (GET_FIELD(baud, UBAUD_PRESCALER) == 0x38) result = 38400; - result >>= GET_FIELD(baud, UBAUD_DIVIDE); - - return result; -} - -/* - * ------------------------------------------------------------ - * rs_stop() and rs_start() - * - * This routines are called before setting or resetting tty->stopped. - * They enable or disable transmitter interrupts, as necessary. - * ------------------------------------------------------------ - */ -static void rs_stop(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_stop")) - return; - - local_irq_save(flags); - uart->ustcnt &= ~USTCNT_TXEN; - local_irq_restore(flags); -} - -static int rs_put_char(char ch) -{ - unsigned long flags; - int loops = 0; - - local_irq_save(flags); - - while (!(UTX & UTX_TX_AVAIL) && (loops < 1000)) { - loops++; - udelay(5); - } - - UTX_TXDATA = ch; - udelay(5); - local_irq_restore(flags); - return 1; -} - -static void rs_start(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_start")) - return; - - local_irq_save(flags); - if (info->xmit_cnt && info->xmit_buf && !(uart->ustcnt & USTCNT_TXEN)) { -#ifdef USE_INTS - uart->ustcnt |= USTCNT_TXEN | USTCNT_TX_INTR_MASK; -#else - uart->ustcnt |= USTCNT_TXEN; -#endif - } - local_irq_restore(flags); -} - -static void receive_chars(struct m68k_serial *info, unsigned short rx) -{ - m68328_uart *uart = &uart_addr[info->line]; - unsigned char ch, flag; - - /* - * This do { } while() loop will get ALL chars out of Rx FIFO - */ -#ifndef CONFIG_XCOPILOT_BUGS - do { -#endif - ch = GET_FIELD(rx, URX_RXDATA); - - if (info->is_cons) { - if (URX_BREAK & rx) { /* whee, break received */ - return; -#ifdef CONFIG_MAGIC_SYSRQ - } else if (ch == 0x10) { /* ^P */ - show_state(); - show_free_areas(0); - show_buffers(); -/* show_net_buffers(); */ - return; - } else if (ch == 0x12) { /* ^R */ - emergency_restart(); - return; -#endif /* CONFIG_MAGIC_SYSRQ */ - } - } - - flag = TTY_NORMAL; - - if (rx & URX_PARITY_ERROR) - flag = TTY_PARITY; - else if (rx & URX_OVRUN) - flag = TTY_OVERRUN; - else if (rx & URX_FRAME_ERROR) - flag = TTY_FRAME; - - tty_insert_flip_char(&info->tport, ch, flag); -#ifndef CONFIG_XCOPILOT_BUGS - } while ((rx = uart->urx.w) & URX_DATA_READY); -#endif - - tty_schedule_flip(&info->tport); -} - -static void transmit_chars(struct m68k_serial *info, struct tty_struct *tty) -{ - m68328_uart *uart = &uart_addr[info->line]; - - if (info->x_char) { - /* Send next char */ - uart->utx.b.txdata = info->x_char; - info->x_char = 0; - goto clear_and_return; - } - - if ((info->xmit_cnt <= 0) || !tty || tty->stopped) { - /* That's peculiar... TX ints off */ - uart->ustcnt &= ~USTCNT_TX_INTR_MASK; - goto clear_and_return; - } - - /* Send char */ - uart->utx.b.txdata = info->xmit_buf[info->xmit_tail++]; - info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1); - info->xmit_cnt--; - - if (info->xmit_cnt <= 0) { - /* All done for now... TX ints off */ - uart->ustcnt &= ~USTCNT_TX_INTR_MASK; - goto clear_and_return; - } - -clear_and_return: - /* Clear interrupt (should be auto)*/ - return; -} - -/* - * This is the serial driver's generic interrupt routine - */ -irqreturn_t rs_interrupt(int irq, void *dev_id) -{ - struct m68k_serial *info = dev_id; - struct tty_struct *tty = tty_port_tty_get(&info->tport); - m68328_uart *uart; - unsigned short rx; - unsigned short tx; - - uart = &uart_addr[info->line]; - rx = uart->urx.w; - -#ifdef USE_INTS - tx = uart->utx.w; - - if (rx & URX_DATA_READY) - receive_chars(info, rx); - if (tx & UTX_TX_AVAIL) - transmit_chars(info, tty); -#else - receive_chars(info, rx); -#endif - tty_kref_put(tty); - - return IRQ_HANDLED; -} - -static int startup(struct m68k_serial *info, struct tty_struct *tty) -{ - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - - if (info->tport.flags & ASYNC_INITIALIZED) - return 0; - - if (!info->xmit_buf) { - info->xmit_buf = (unsigned char *) __get_free_page(GFP_KERNEL); - if (!info->xmit_buf) - return -ENOMEM; - } - - local_irq_save(flags); - - /* - * Clear the FIFO buffers and disable them - * (they will be reenabled in change_speed()) - */ - - uart->ustcnt = USTCNT_UEN; - uart->ustcnt = USTCNT_UEN | USTCNT_RXEN | USTCNT_TXEN; - (void)uart->urx.w; - - /* - * Finally, enable sequencing and interrupts - */ -#ifdef USE_INTS - uart->ustcnt = USTCNT_UEN | USTCNT_RXEN | - USTCNT_RX_INTR_MASK | USTCNT_TX_INTR_MASK; -#else - uart->ustcnt = USTCNT_UEN | USTCNT_RXEN | USTCNT_RX_INTR_MASK; -#endif - - if (tty) - clear_bit(TTY_IO_ERROR, &tty->flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - - /* - * and set the speed of the serial port - */ - - change_speed(info, tty); - - info->tport.flags |= ASYNC_INITIALIZED; - local_irq_restore(flags); - return 0; -} - -/* - * This routine will shutdown a serial port; interrupts are disabled, and - * DTR is dropped if the hangup on close termio flag is on. - */ -static void shutdown(struct m68k_serial *info, struct tty_struct *tty) -{ - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - - uart->ustcnt = 0; /* All off! */ - if (!(info->tport.flags & ASYNC_INITIALIZED)) - return; - - local_irq_save(flags); - - if (info->xmit_buf) { - free_page((unsigned long) info->xmit_buf); - info->xmit_buf = 0; - } - - if (tty) - set_bit(TTY_IO_ERROR, &tty->flags); - - info->tport.flags &= ~ASYNC_INITIALIZED; - local_irq_restore(flags); -} - -struct { - int divisor, prescale; -} -#ifndef CONFIG_M68VZ328 - hw_baud_table[18] = { - {0, 0}, /* 0 */ - {0, 0}, /* 50 */ - {0, 0}, /* 75 */ - {0, 0}, /* 110 */ - {0, 0}, /* 134 */ - {0, 0}, /* 150 */ - {0, 0}, /* 200 */ - {7, 0x26}, /* 300 */ - {6, 0x26}, /* 600 */ - {5, 0x26}, /* 1200 */ - {0, 0}, /* 1800 */ - {4, 0x26}, /* 2400 */ - {3, 0x26}, /* 4800 */ - {2, 0x26}, /* 9600 */ - {1, 0x26}, /* 19200 */ - {0, 0x26}, /* 38400 */ - {1, 0x38}, /* 57600 */ - {0, 0x38}, /* 115200 */ -}; -#else - hw_baud_table[18] = { - {0, 0}, /* 0 */ - {0, 0}, /* 50 */ - {0, 0}, /* 75 */ - {0, 0}, /* 110 */ - {0, 0}, /* 134 */ - {0, 0}, /* 150 */ - {0, 0}, /* 200 */ - {0, 0}, /* 300 */ - {7, 0x26}, /* 600 */ - {6, 0x26}, /* 1200 */ - {0, 0}, /* 1800 */ - {5, 0x26}, /* 2400 */ - {4, 0x26}, /* 4800 */ - {3, 0x26}, /* 9600 */ - {2, 0x26}, /* 19200 */ - {1, 0x26}, /* 38400 */ - {0, 0x26}, /* 57600 */ - {1, 0x38}, /* 115200 */ -}; -#endif -/* rate = 1036800 / ((65 - prescale) * (1<<divider)) */ - -/* - * This routine is called to set the UART divisor registers to match - * the specified baud rate for a serial port. - */ -static void change_speed(struct m68k_serial *info, struct tty_struct *tty) -{ - m68328_uart *uart = &uart_addr[info->line]; - unsigned short port; - unsigned short ustcnt; - unsigned cflag; - int i; - - cflag = tty->termios.c_cflag; - port = info->port; - if (!port) - return; - - ustcnt = uart->ustcnt; - uart->ustcnt = ustcnt & ~USTCNT_TXEN; - - i = cflag & CBAUD; - if (i & CBAUDEX) { - i = (i & ~CBAUDEX) + B38400; - } - - uart->ubaud = PUT_FIELD(UBAUD_DIVIDE, hw_baud_table[i].divisor) | - PUT_FIELD(UBAUD_PRESCALER, hw_baud_table[i].prescale); - - ustcnt &= ~(USTCNT_PARITYEN | USTCNT_ODD_EVEN | USTCNT_STOP | USTCNT_8_7); - - if ((cflag & CSIZE) == CS8) - ustcnt |= USTCNT_8_7; - - if (cflag & CSTOPB) - ustcnt |= USTCNT_STOP; - - if (cflag & PARENB) - ustcnt |= USTCNT_PARITYEN; - if (cflag & PARODD) - ustcnt |= USTCNT_ODD_EVEN; - -#ifdef CONFIG_SERIAL_68328_RTS_CTS - if (cflag & CRTSCTS) { - uart->utx.w &= ~UTX_NOCTS; - } else { - uart->utx.w |= UTX_NOCTS; - } -#endif - - ustcnt |= USTCNT_TXEN; - - uart->ustcnt = ustcnt; - return; -} - -/* - * Fair output driver allows a process to speak. - */ -static void rs_fair_output(void) -{ - int left; /* Output no more than that */ - unsigned long flags; - struct m68k_serial *info = &m68k_soft[0]; - char c; - - if (info == NULL) return; - if (info->xmit_buf == NULL) return; - - local_irq_save(flags); - left = info->xmit_cnt; - while (left != 0) { - c = info->xmit_buf[info->xmit_tail]; - info->xmit_tail = (info->xmit_tail+1) & (SERIAL_XMIT_SIZE-1); - info->xmit_cnt--; - local_irq_restore(flags); - - rs_put_char(c); - - local_irq_save(flags); - left = min(info->xmit_cnt, left-1); - } - - /* Last character is being transmitted now (hopefully). */ - udelay(5); - - local_irq_restore(flags); - return; -} - -/* - * m68k_console_print is registered for printk. - */ -void console_print_68328(const char *p) -{ - char c; - - while ((c = *(p++)) != 0) { - if (c == '\n') - rs_put_char('\r'); - rs_put_char(c); - } - - /* Comment this if you want to have a strict interrupt-driven output */ - rs_fair_output(); - - return; -} - -static void rs_set_ldisc(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_set_ldisc")) - return; - - info->is_cons = (tty->termios.c_line == N_TTY); - - printk("ttyS%d console mode %s\n", info->line, info->is_cons ? "on" : "off"); -} - -static void rs_flush_chars(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_flush_chars")) - return; -#ifndef USE_INTS - for (;;) { -#endif - - /* Enable transmitter */ - local_irq_save(flags); - - if (info->xmit_cnt <= 0 || tty->stopped || !info->xmit_buf) { - local_irq_restore(flags); - return; - } - -#ifdef USE_INTS - uart->ustcnt |= USTCNT_TXEN | USTCNT_TX_INTR_MASK; -#else - uart->ustcnt |= USTCNT_TXEN; -#endif - -#ifdef USE_INTS - if (uart->utx.w & UTX_TX_AVAIL) { -#else - if (1) { -#endif - /* Send char */ - uart->utx.b.txdata = info->xmit_buf[info->xmit_tail++]; - info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1); - info->xmit_cnt--; - } - -#ifndef USE_INTS - while (!(uart->utx.w & UTX_TX_AVAIL)) udelay(5); - } -#endif - local_irq_restore(flags); -} - -extern void console_printn(const char *b, int count); - -static int rs_write(struct tty_struct *tty, - const unsigned char *buf, int count) -{ - int c, total = 0; - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_write")) - return 0; - - if (!tty || !info->xmit_buf) - return 0; - - local_save_flags(flags); - while (1) { - local_irq_disable(); - c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, - SERIAL_XMIT_SIZE - info->xmit_head)); - local_irq_restore(flags); - - if (c <= 0) - break; - - memcpy(info->xmit_buf + info->xmit_head, buf, c); - - local_irq_disable(); - info->xmit_head = (info->xmit_head + c) & (SERIAL_XMIT_SIZE-1); - info->xmit_cnt += c; - local_irq_restore(flags); - buf += c; - count -= c; - total += c; - } - - if (info->xmit_cnt && !tty->stopped) { - /* Enable transmitter */ - local_irq_disable(); -#ifndef USE_INTS - while (info->xmit_cnt) { -#endif - - uart->ustcnt |= USTCNT_TXEN; -#ifdef USE_INTS - uart->ustcnt |= USTCNT_TX_INTR_MASK; -#else - while (!(uart->utx.w & UTX_TX_AVAIL)) udelay(5); -#endif - if (uart->utx.w & UTX_TX_AVAIL) { - uart->utx.b.txdata = info->xmit_buf[info->xmit_tail++]; - info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1); - info->xmit_cnt--; - } - -#ifndef USE_INTS - } -#endif - local_irq_restore(flags); - } - - return total; -} - -static int rs_write_room(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - int ret; - - if (serial_paranoia_check(info, tty->name, "rs_write_room")) - return 0; - ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1; - if (ret < 0) - ret = 0; - return ret; -} - -static int rs_chars_in_buffer(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer")) - return 0; - return info->xmit_cnt; -} - -static void rs_flush_buffer(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_flush_buffer")) - return; - local_irq_save(flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - local_irq_restore(flags); - tty_wakeup(tty); -} - -/* - * ------------------------------------------------------------ - * rs_throttle() - * - * This routine is called by the upper-layer tty layer to signal that - * incoming characters should be throttled. - * ------------------------------------------------------------ - */ -static void rs_throttle(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_throttle")) - return; - - if (I_IXOFF(tty)) - info->x_char = STOP_CHAR(tty); - - /* Turn off RTS line (do this atomic) */ -} - -static void rs_unthrottle(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_unthrottle")) - return; - - if (I_IXOFF(tty)) { - if (info->x_char) - info->x_char = 0; - else - info->x_char = START_CHAR(tty); - } - - /* Assert RTS line (do this atomic) */ -} - -/* - * ------------------------------------------------------------ - * rs_ioctl() and friends - * ------------------------------------------------------------ - */ - -static int get_serial_info(struct m68k_serial *info, - struct serial_struct *retinfo) -{ - struct serial_struct tmp; - - if (!retinfo) - return -EFAULT; - memset(&tmp, 0, sizeof(tmp)); - tmp.type = info->type; - tmp.line = info->line; - tmp.port = info->port; - tmp.irq = info->irq; - tmp.flags = info->tport.flags; - tmp.baud_base = info->baud_base; - tmp.close_delay = info->tport.close_delay; - tmp.closing_wait = info->tport.closing_wait; - tmp.custom_divisor = info->custom_divisor; - if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) - return -EFAULT; - - return 0; -} - -static int set_serial_info(struct m68k_serial *info, struct tty_struct *tty, - struct serial_struct *new_info) -{ - struct tty_port *port = &info->tport; - struct serial_struct new_serial; - struct m68k_serial old_info; - int retval = 0; - - if (!new_info) - return -EFAULT; - if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) - return -EFAULT; - old_info = *info; - - if (!capable(CAP_SYS_ADMIN)) { - if ((new_serial.baud_base != info->baud_base) || - (new_serial.type != info->type) || - (new_serial.close_delay != port->close_delay) || - ((new_serial.flags & ~ASYNC_USR_MASK) != - (port->flags & ~ASYNC_USR_MASK))) - return -EPERM; - port->flags = ((port->flags & ~ASYNC_USR_MASK) | - (new_serial.flags & ASYNC_USR_MASK)); - info->custom_divisor = new_serial.custom_divisor; - goto check_and_exit; - } - - if (port->count > 1) - return -EBUSY; - - /* - * OK, past this point, all the error checking has been done. - * At this point, we start making changes..... - */ - - info->baud_base = new_serial.baud_base; - port->flags = ((port->flags & ~ASYNC_FLAGS) | - (new_serial.flags & ASYNC_FLAGS)); - info->type = new_serial.type; - port->close_delay = new_serial.close_delay; - port->closing_wait = new_serial.closing_wait; - -check_and_exit: - retval = startup(info, tty); - return retval; -} - -/* - * get_lsr_info - get line status register info - * - * Purpose: Let user call ioctl() to get info when the UART physically - * is emptied. On bus types like RS485, the transmitter must - * release the bus after transmitting. This must be done when - * the transmit shift register is empty, not be done when the - * transmit holding register is empty. This functionality - * allows an RS485 driver to be written in user space. - */ -static int get_lsr_info(struct m68k_serial *info, unsigned int *value) -{ -#ifdef CONFIG_SERIAL_68328_RTS_CTS - m68328_uart *uart = &uart_addr[info->line]; -#endif - unsigned char status; - unsigned long flags; - - local_irq_save(flags); -#ifdef CONFIG_SERIAL_68328_RTS_CTS - status = (uart->utx.w & UTX_CTS_STAT) ? 1 : 0; -#else - status = 0; -#endif - local_irq_restore(flags); - return put_user(status, value); -} - -/* - * This routine sends a break character out the serial port. - */ -static void send_break(struct m68k_serial *info, unsigned int duration) -{ - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - if (!info->port) - return; - local_irq_save(flags); -#ifdef USE_INTS - uart->utx.w |= UTX_SEND_BREAK; - msleep_interruptible(duration); - uart->utx.w &= ~UTX_SEND_BREAK; -#endif - local_irq_restore(flags); -} - -static int rs_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - int retval; - - if (serial_paranoia_check(info, tty->name, "rs_ioctl")) - return -ENODEV; - - if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && - (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) && - (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) { - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - } - - switch (cmd) { - case TCSBRK: /* SVID version: non-zero arg --> no break */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - if (!arg) - send_break(info, 250); /* 1/4 second */ - return 0; - case TCSBRKP: /* support for POSIX tcsendbreak() */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - send_break(info, arg ? arg*(100) : 250); - return 0; - case TIOCGSERIAL: - return get_serial_info(info, - (struct serial_struct *) arg); - case TIOCSSERIAL: - return set_serial_info(info, tty, - (struct serial_struct *) arg); - case TIOCSERGETLSR: /* Get line status register */ - return get_lsr_info(info, (unsigned int *) arg); - case TIOCSERGSTRUCT: - if (copy_to_user((struct m68k_serial *) arg, - info, sizeof(struct m68k_serial))) - return -EFAULT; - return 0; - default: - return -ENOIOCTLCMD; - } - return 0; -} - -static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - - change_speed(info, tty); - - if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios.c_cflag & CRTSCTS)) - rs_start(tty); - -} - -/* - * ------------------------------------------------------------ - * rs_close() - * - * This routine is called when the serial port gets closed. First, we - * wait for the last remaining data to be sent. Then, we unlink its - * S structure from the interrupt chain if necessary, and we free - * that IRQ if nothing is left in the chain. - * ------------------------------------------------------------ - */ -static void rs_close(struct tty_struct *tty, struct file *filp) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - struct tty_port *port = &info->tport; - m68328_uart *uart = &uart_addr[info->line]; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_close")) - return; - - local_irq_save(flags); - - if (tty_hung_up_p(filp)) { - local_irq_restore(flags); - return; - } - - if ((tty->count == 1) && (port->count != 1)) { - /* - * Uh, oh. tty->count is 1, which means that the tty - * structure will be freed. Info->count should always - * be one in these conditions. If it's greater than - * one, we've got real problems, since it means the - * serial port won't be shutdown. - */ - printk("rs_close: bad serial port count; tty->count is 1, " - "port->count is %d\n", port->count); - port->count = 1; - } - if (--port->count < 0) { - printk("rs_close: bad serial port count for ttyS%d: %d\n", - info->line, port->count); - port->count = 0; - } - if (port->count) { - local_irq_restore(flags); - return; - } - port->flags |= ASYNC_CLOSING; - /* - * Now we wait for the transmit buffer to clear; and we notify - * the line discipline to only process XON/XOFF characters. - */ - tty->closing = 1; - if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE) - tty_wait_until_sent(tty, port->closing_wait); - /* - * At this point we stop accepting input. To do this, we - * disable the receive line status interrupts, and tell the - * interrupt driver to stop checking the data ready bit in the - * line status register. - */ - - uart->ustcnt &= ~USTCNT_RXEN; - uart->ustcnt &= ~(USTCNT_RXEN | USTCNT_RX_INTR_MASK); - - shutdown(info, tty); - rs_flush_buffer(tty); - - tty_ldisc_flush(tty); - tty->closing = 0; - tty_port_tty_set(&info->tport, NULL); -#warning "This is not and has never been valid so fix it" -#if 0 - if (tty->ldisc.num != ldiscs[N_TTY].num) { - if (tty->ldisc.close) - (tty->ldisc.close)(tty); - tty->ldisc = ldiscs[N_TTY]; - tty->termios.c_line = N_TTY; - if (tty->ldisc.open) - (tty->ldisc.open)(tty); - } -#endif - if (port->blocked_open) { - if (port->close_delay) - msleep_interruptible(jiffies_to_msecs(port->close_delay)); - wake_up_interruptible(&port->open_wait); - } - port->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); - local_irq_restore(flags); -} - -/* - * rs_hangup() --- called by tty_hangup() when a hangup is signaled. - */ -void rs_hangup(struct tty_struct *tty) -{ - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_hangup")) - return; - - rs_flush_buffer(tty); - shutdown(info, tty); - info->tport.count = 0; - info->tport.flags &= ~ASYNC_NORMAL_ACTIVE; - tty_port_tty_set(&info->tport, NULL); - wake_up_interruptible(&info->tport.open_wait); -} - -/* - * This routine is called whenever a serial port is opened. It - * enables interrupts for a serial port, linking in its S structure into - * the IRQ chain. It also performs the serial-specific - * initialization for the tty structure. - */ -int rs_open(struct tty_struct *tty, struct file *filp) -{ - struct m68k_serial *info; - int retval; - - info = &m68k_soft[tty->index]; - - if (serial_paranoia_check(info, tty->name, "rs_open")) - return -ENODEV; - - info->tport.count++; - tty->driver_data = info; - tty_port_tty_set(&info->tport, tty); - - /* - * Start up serial port - */ - retval = startup(info, tty); - if (retval) - return retval; - - return tty_port_block_til_ready(&info->tport, tty, filp); -} - -/* Finally, routines used to initialize the serial driver. */ - -static void show_serial_version(void) -{ - printk("MC68328 serial driver version 1.00\n"); -} - -static const struct tty_operations rs_ops = { - .open = rs_open, - .close = rs_close, - .write = rs_write, - .flush_chars = rs_flush_chars, - .write_room = rs_write_room, - .chars_in_buffer = rs_chars_in_buffer, - .flush_buffer = rs_flush_buffer, - .ioctl = rs_ioctl, - .throttle = rs_throttle, - .unthrottle = rs_unthrottle, - .set_termios = rs_set_termios, - .stop = rs_stop, - .start = rs_start, - .hangup = rs_hangup, - .set_ldisc = rs_set_ldisc, -}; - -static const struct tty_port_operations rs_port_ops = { -}; - -/* rs_init inits the driver */ -static int __init -rs68328_init(void) -{ - unsigned long flags; - int i; - struct m68k_serial *info; - - serial_driver = alloc_tty_driver(NR_PORTS); - if (!serial_driver) - return -ENOMEM; - - show_serial_version(); - - /* Initialize the tty_driver structure */ - /* SPARC: Not all of this is exactly right for us. */ - - serial_driver->name = "ttyS"; - serial_driver->major = TTY_MAJOR; - serial_driver->minor_start = 64; - serial_driver->type = TTY_DRIVER_TYPE_SERIAL; - serial_driver->subtype = SERIAL_TYPE_NORMAL; - serial_driver->init_termios = tty_std_termios; - serial_driver->init_termios.c_cflag = - m68328_console_cbaud | CS8 | CREAD | HUPCL | CLOCAL; - serial_driver->flags = TTY_DRIVER_REAL_RAW; - tty_set_operations(serial_driver, &rs_ops); - - local_irq_save(flags); - - for (i = 0; i < NR_PORTS; i++) { - - info = &m68k_soft[i]; - tty_port_init(&info->tport); - info->tport.ops = &rs_port_ops; - info->magic = SERIAL_MAGIC; - info->port = (int) &uart_addr[i]; - info->irq = uart_irqs[i]; - info->custom_divisor = 16; - info->x_char = 0; - info->line = i; - info->is_cons = 1; /* Means shortcuts work */ - - printk("%s%d at 0x%08x (irq = %d)", serial_driver->name, info->line, - info->port, info->irq); - printk(" is a builtin MC68328 UART\n"); - -#ifdef CONFIG_M68VZ328 - if (i > 0) - PJSEL &= 0xCF; /* PSW enable second port output */ -#endif - - if (request_irq(uart_irqs[i], - rs_interrupt, - 0, - "M68328_UART", info)) - panic("Unable to attach 68328 serial interrupt\n"); - - tty_port_link_device(&info->tport, serial_driver, i); - } - local_irq_restore(flags); - - if (tty_register_driver(serial_driver)) { - put_tty_driver(serial_driver); - for (i = 0; i < NR_PORTS; i++) - tty_port_destroy(&m68k_soft[i].tport); - printk(KERN_ERR "Couldn't register serial driver\n"); - return -ENOMEM; - } - - return 0; -} - -module_init(rs68328_init); - - - -static void m68328_set_baud(void) -{ - unsigned short ustcnt; - int i; - - ustcnt = USTCNT; - USTCNT = ustcnt & ~USTCNT_TXEN; - -again: - for (i = 0; i < ARRAY_SIZE(baud_table); i++) - if (baud_table[i] == m68328_console_baud) - break; - if (i >= ARRAY_SIZE(baud_table)) { - m68328_console_baud = 9600; - goto again; - } - - UBAUD = PUT_FIELD(UBAUD_DIVIDE, hw_baud_table[i].divisor) | - PUT_FIELD(UBAUD_PRESCALER, hw_baud_table[i].prescale); - ustcnt &= ~(USTCNT_PARITYEN | USTCNT_ODD_EVEN | USTCNT_STOP | USTCNT_8_7); - ustcnt |= USTCNT_8_7; - ustcnt |= USTCNT_TXEN; - USTCNT = ustcnt; - m68328_console_initted = 1; - return; -} - - -int m68328_console_setup(struct console *cp, char *arg) -{ - int i, n = CONSOLE_BAUD_RATE; - - if (!cp) - return(-1); - - if (arg) - n = simple_strtoul(arg, NULL, 0); - - for (i = 0; i < ARRAY_SIZE(baud_table); i++) - if (baud_table[i] == n) - break; - if (i < ARRAY_SIZE(baud_table)) { - m68328_console_baud = n; - m68328_console_cbaud = 0; - if (i > 15) { - m68328_console_cbaud |= CBAUDEX; - i -= 15; - } - m68328_console_cbaud |= i; - } - - m68328_set_baud(); /* make sure baud rate changes */ - return 0; -} - - -static struct tty_driver *m68328_console_device(struct console *c, int *index) -{ - *index = c->index; - return serial_driver; -} - - -void m68328_console_write (struct console *co, const char *str, - unsigned int count) -{ - if (!m68328_console_initted) - m68328_set_baud(); - while (count--) { - if (*str == '\n') - rs_put_char('\r'); - rs_put_char(*str++); - } -} - - -static struct console m68328_driver = { - .name = "ttyS", - .write = m68328_console_write, - .device = m68328_console_device, - .setup = m68328_console_setup, - .flags = CON_PRINTBUFFER, - .index = -1, -}; - - -static int __init m68328_console_init(void) -{ - register_console(&m68328_driver); - return 0; -} - -console_initcall(m68328_console_init); diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h index d54dcd87c67e..047a7ba6796a 100644 --- a/drivers/tty/serial/8250/8250.h +++ b/drivers/tty/serial/8250/8250.h @@ -92,6 +92,18 @@ struct serial8250_config { #define SERIAL8250_SHARE_IRQS 0 #endif +#define SERIAL8250_PORT_FLAGS(_base, _irq, _flags) \ + { \ + .iobase = _base, \ + .irq = _irq, \ + .uartclk = 1843200, \ + .iotype = UPIO_PORT, \ + .flags = UPF_BOOT_AUTOCONF | (_flags), \ + } + +#define SERIAL8250_PORT(_base, _irq) SERIAL8250_PORT_FLAGS(_base, _irq, 0) + + static inline int serial_in(struct uart_8250_port *up, int offset) { return up->port.serial_in(&up->port, offset); @@ -117,6 +129,8 @@ static inline void serial_dl_write(struct uart_8250_port *up, int value) struct uart_8250_port *serial8250_get_port(int line); void serial8250_rpm_get(struct uart_8250_port *p); void serial8250_rpm_put(struct uart_8250_port *p); +int serial8250_em485_init(struct uart_8250_port *p); +void serial8250_em485_destroy(struct uart_8250_port *p); #if defined(__alpha__) && !defined(CONFIG_PCI) /* diff --git a/drivers/tty/serial/8250/8250_accent.c b/drivers/tty/serial/8250/8250_accent.c index 34b51c651192..522aeae05192 100644 --- a/drivers/tty/serial/8250/8250_accent.c +++ b/drivers/tty/serial/8250/8250_accent.c @@ -10,18 +10,11 @@ #include <linux/init.h> #include <linux/serial_8250.h> -#define PORT(_base,_irq) \ - { \ - .iobase = _base, \ - .irq = _irq, \ - .uartclk = 1843200, \ - .iotype = UPIO_PORT, \ - .flags = UPF_BOOT_AUTOCONF, \ - } +#include "8250.h" static struct plat_serial8250_port accent_data[] = { - PORT(0x330, 4), - PORT(0x338, 4), + SERIAL8250_PORT(0x330, 4), + SERIAL8250_PORT(0x338, 4), { }, }; diff --git a/drivers/tty/serial/8250/8250_acorn.c b/drivers/tty/serial/8250/8250_acorn.c index 549aa07c0d27..402dfdd4940e 100644 --- a/drivers/tty/serial/8250/8250_acorn.c +++ b/drivers/tty/serial/8250/8250_acorn.c @@ -70,7 +70,7 @@ serial_card_probe(struct expansion_card *ec, const struct ecard_id *id) uart.port.regshift = 2; uart.port.dev = &ec->dev; - for (i = 0; i < info->num_ports; i ++) { + for (i = 0; i < info->num_ports; i++) { uart.port.membase = info->vaddr + type->offset[i]; uart.port.mapbase = bus_addr + type->offset[i]; diff --git a/drivers/tty/serial/8250/8250_bcm2835aux.c b/drivers/tty/serial/8250/8250_bcm2835aux.c new file mode 100644 index 000000000000..e10f1244409b --- /dev/null +++ b/drivers/tty/serial/8250/8250_bcm2835aux.c @@ -0,0 +1,146 @@ +/* + * Serial port driver for BCM2835AUX UART + * + * Copyright (C) 2016 Martin Sperl <kernel@martin.sperl.org> + * + * Based on 8250_lpc18xx.c: + * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include "8250.h" + +struct bcm2835aux_data { + struct uart_8250_port uart; + struct clk *clk; + int line; +}; + +static int bcm2835aux_serial_probe(struct platform_device *pdev) +{ + struct bcm2835aux_data *data; + struct resource *res; + int ret; + + /* allocate the custom structure */ + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + /* initialize data */ + spin_lock_init(&data->uart.port.lock); + data->uart.capabilities = UART_CAP_FIFO; + data->uart.port.dev = &pdev->dev; + data->uart.port.regshift = 2; + data->uart.port.type = PORT_16550; + data->uart.port.iotype = UPIO_MEM; + data->uart.port.fifosize = 8; + data->uart.port.flags = UPF_SHARE_IRQ | + UPF_FIXED_PORT | + UPF_FIXED_TYPE | + UPF_SKIP_TEST; + + /* get the clock - this also enables the HW */ + data->clk = devm_clk_get(&pdev->dev, NULL); + ret = PTR_ERR_OR_ZERO(data->clk); + if (ret) { + dev_err(&pdev->dev, "could not get clk: %d\n", ret); + return ret; + } + + /* get the interrupt */ + ret = platform_get_irq(pdev, 0); + if (ret < 0) { + dev_err(&pdev->dev, "irq not found - %i", ret); + return ret; + } + data->uart.port.irq = ret; + + /* map the main registers */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "memory resource not found"); + return -EINVAL; + } + data->uart.port.membase = devm_ioremap_resource(&pdev->dev, res); + ret = PTR_ERR_OR_ZERO(data->uart.port.membase); + if (ret) + return ret; + + /* Check for a fixed line number */ + ret = of_alias_get_id(pdev->dev.of_node, "serial"); + if (ret >= 0) + data->uart.port.line = ret; + + /* enable the clock as a last step */ + ret = clk_prepare_enable(data->clk); + if (ret) { + dev_err(&pdev->dev, "unable to enable uart clock - %d\n", + ret); + return ret; + } + + /* the HW-clock divider for bcm2835aux is 8, + * but 8250 expects a divider of 16, + * so we have to multiply the actual clock by 2 + * to get identical baudrates. + */ + data->uart.port.uartclk = clk_get_rate(data->clk) * 2; + + /* register the port */ + ret = serial8250_register_8250_port(&data->uart); + if (ret < 0) { + dev_err(&pdev->dev, "unable to register 8250 port - %d\n", + ret); + goto dis_clk; + } + data->line = ret; + + platform_set_drvdata(pdev, data); + + return 0; + +dis_clk: + clk_disable_unprepare(data->clk); + return ret; +} + +static int bcm2835aux_serial_remove(struct platform_device *pdev) +{ + struct bcm2835aux_data *data = platform_get_drvdata(pdev); + + serial8250_unregister_port(data->uart.port.line); + clk_disable_unprepare(data->clk); + + return 0; +} + +static const struct of_device_id bcm2835aux_serial_match[] = { + { .compatible = "brcm,bcm2835-aux-uart" }, + { }, +}; +MODULE_DEVICE_TABLE(of, bcm2835aux_serial_match); + +static struct platform_driver bcm2835aux_serial_driver = { + .driver = { + .name = "bcm2835-aux-uart", + .of_match_table = bcm2835aux_serial_match, + }, + .probe = bcm2835aux_serial_probe, + .remove = bcm2835aux_serial_remove, +}; +module_platform_driver(bcm2835aux_serial_driver); + +MODULE_DESCRIPTION("BCM2835 auxiliar UART driver"); +MODULE_AUTHOR("Martin Sperl <kernel@martin.sperl.org>"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/tty/serial/8250/8250_boca.c b/drivers/tty/serial/8250/8250_boca.c index d125dc107985..a63b5998e383 100644 --- a/drivers/tty/serial/8250/8250_boca.c +++ b/drivers/tty/serial/8250/8250_boca.c @@ -10,32 +10,25 @@ #include <linux/init.h> #include <linux/serial_8250.h> -#define PORT(_base,_irq) \ - { \ - .iobase = _base, \ - .irq = _irq, \ - .uartclk = 1843200, \ - .iotype = UPIO_PORT, \ - .flags = UPF_BOOT_AUTOCONF, \ - } +#include "8250.h" static struct plat_serial8250_port boca_data[] = { - PORT(0x100, 12), - PORT(0x108, 12), - PORT(0x110, 12), - PORT(0x118, 12), - PORT(0x120, 12), - PORT(0x128, 12), - PORT(0x130, 12), - PORT(0x138, 12), - PORT(0x140, 12), - PORT(0x148, 12), - PORT(0x150, 12), - PORT(0x158, 12), - PORT(0x160, 12), - PORT(0x168, 12), - PORT(0x170, 12), - PORT(0x178, 12), + SERIAL8250_PORT(0x100, 12), + SERIAL8250_PORT(0x108, 12), + SERIAL8250_PORT(0x110, 12), + SERIAL8250_PORT(0x118, 12), + SERIAL8250_PORT(0x120, 12), + SERIAL8250_PORT(0x128, 12), + SERIAL8250_PORT(0x130, 12), + SERIAL8250_PORT(0x138, 12), + SERIAL8250_PORT(0x140, 12), + SERIAL8250_PORT(0x148, 12), + SERIAL8250_PORT(0x150, 12), + SERIAL8250_PORT(0x158, 12), + SERIAL8250_PORT(0x160, 12), + SERIAL8250_PORT(0x168, 12), + SERIAL8250_PORT(0x170, 12), + SERIAL8250_PORT(0x178, 12), { }, }; diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index c9720a97a977..2f4f5ee651db 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -597,6 +597,7 @@ static void univ8250_console_write(struct console *co, const char *s, static int univ8250_console_setup(struct console *co, char *options) { struct uart_port *port; + int retval; /* * Check whether an invalid uart number has been specified, and @@ -609,7 +610,10 @@ static int univ8250_console_setup(struct console *co, char *options) /* link port to console */ port->cons = co; - return serial8250_console_setup(port, options, false); + retval = serial8250_console_setup(port, options, false); + if (retval != 0) + port->cons = NULL; + return retval; } /** @@ -687,7 +691,7 @@ static int __init univ8250_console_init(void) } console_initcall(univ8250_console_init); -#define SERIAL8250_CONSOLE &univ8250_console +#define SERIAL8250_CONSOLE (&univ8250_console) #else #define SERIAL8250_CONSOLE NULL #endif @@ -764,6 +768,7 @@ void serial8250_suspend_port(int line) uart_suspend_port(&serial8250_reg, port); } +EXPORT_SYMBOL(serial8250_suspend_port); /** * serial8250_resume_port - resume one serial port @@ -789,6 +794,7 @@ void serial8250_resume_port(int line) } uart_resume_port(&serial8250_reg, port); } +EXPORT_SYMBOL(serial8250_resume_port); /* * Register a set of serial devices attached to a platform device. The @@ -1068,6 +1074,15 @@ void serial8250_unregister_port(int line) struct uart_8250_port *uart = &serial8250_ports[line]; mutex_lock(&serial_mutex); + + if (uart->em485) { + unsigned long flags; + + spin_lock_irqsave(&uart->port.lock, flags); + serial8250_em485_destroy(uart); + spin_unlock_irqrestore(&uart->port.lock, flags); + } + uart_remove_one_port(&serial8250_reg, &uart->port); if (serial8250_isa_devs) { uart->port.flags &= ~UPF_BOOT_AUTOCONF; @@ -1093,9 +1108,8 @@ static int __init serial8250_init(void) serial8250_isa_init_ports(); - printk(KERN_INFO "Serial: 8250/16550 driver, " - "%d ports, IRQ sharing %sabled\n", nr_uarts, - share_irqs ? "en" : "dis"); + pr_info("Serial: 8250/16550 driver, %d ports, IRQ sharing %sabled\n", + nr_uarts, share_irqs ? "en" : "dis"); #ifdef CONFIG_SPARC ret = sunserial_register_minors(&serial8250_reg, UART_NR); @@ -1168,15 +1182,11 @@ static void __exit serial8250_exit(void) module_init(serial8250_init); module_exit(serial8250_exit); -EXPORT_SYMBOL(serial8250_suspend_port); -EXPORT_SYMBOL(serial8250_resume_port); - MODULE_LICENSE("GPL"); MODULE_DESCRIPTION("Generic 8250/16x50 serial driver"); module_param(share_irqs, uint, 0644); -MODULE_PARM_DESC(share_irqs, "Share IRQs with other non-8250/16x50 devices" - " (unsafe)"); +MODULE_PARM_DESC(share_irqs, "Share IRQs with other non-8250/16x50 devices (unsafe)"); module_param(nr_uarts, uint, 0644); MODULE_PARM_DESC(nr_uarts, "Maximum number of UARTs supported. (1-" __MODULE_STRING(CONFIG_SERIAL_8250_NR_UARTS) ")"); diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c index a5d319e4aae6..a3fb95d85d7c 100644 --- a/drivers/tty/serial/8250/8250_dw.c +++ b/drivers/tty/serial/8250/8250_dw.c @@ -68,12 +68,6 @@ struct dw8250_data { unsigned int uart_16550_compatible:1; }; -#define BYT_PRV_CLK 0x800 -#define BYT_PRV_CLK_EN (1 << 0) -#define BYT_PRV_CLK_M_VAL_SHIFT 1 -#define BYT_PRV_CLK_N_VAL_SHIFT 16 -#define BYT_PRV_CLK_UPDATE (1 << 31) - static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value) { struct dw8250_data *d = p->private_data; @@ -95,25 +89,45 @@ static void dw8250_force_idle(struct uart_port *p) (void)p->serial_in(p, UART_RX); } -static void dw8250_serial_out(struct uart_port *p, int offset, int value) +static void dw8250_check_lcr(struct uart_port *p, int value) { - writeb(value, p->membase + (offset << p->regshift)); + void __iomem *offset = p->membase + (UART_LCR << p->regshift); + int tries = 1000; /* Make sure LCR write wasn't ignored */ - if (offset == UART_LCR) { - int tries = 1000; - while (tries--) { - unsigned int lcr = p->serial_in(p, UART_LCR); - if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR)) - return; - dw8250_force_idle(p); - writeb(value, p->membase + (UART_LCR << p->regshift)); - } - /* - * FIXME: this deadlocks if port->lock is already held - * dev_err(p->dev, "Couldn't set LCR to %d\n", value); - */ + while (tries--) { + unsigned int lcr = p->serial_in(p, UART_LCR); + + if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR)) + return; + + dw8250_force_idle(p); + +#ifdef CONFIG_64BIT + __raw_writeq(value & 0xff, offset); +#else + if (p->iotype == UPIO_MEM32) + writel(value, offset); + else if (p->iotype == UPIO_MEM32BE) + iowrite32be(value, offset); + else + writeb(value, offset); +#endif } + /* + * FIXME: this deadlocks if port->lock is already held + * dev_err(p->dev, "Couldn't set LCR to %d\n", value); + */ +} + +static void dw8250_serial_out(struct uart_port *p, int offset, int value) +{ + struct dw8250_data *d = p->private_data; + + writeb(value, p->membase + (offset << p->regshift)); + + if (offset == UART_LCR && !d->uart_16550_compatible) + dw8250_check_lcr(p, value); } static unsigned int dw8250_serial_in(struct uart_port *p, int offset) @@ -135,49 +149,26 @@ static unsigned int dw8250_serial_inq(struct uart_port *p, int offset) static void dw8250_serial_outq(struct uart_port *p, int offset, int value) { + struct dw8250_data *d = p->private_data; + value &= 0xff; __raw_writeq(value, p->membase + (offset << p->regshift)); /* Read back to ensure register write ordering. */ __raw_readq(p->membase + (UART_LCR << p->regshift)); - /* Make sure LCR write wasn't ignored */ - if (offset == UART_LCR) { - int tries = 1000; - while (tries--) { - unsigned int lcr = p->serial_in(p, UART_LCR); - if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR)) - return; - dw8250_force_idle(p); - __raw_writeq(value & 0xff, - p->membase + (UART_LCR << p->regshift)); - } - /* - * FIXME: this deadlocks if port->lock is already held - * dev_err(p->dev, "Couldn't set LCR to %d\n", value); - */ - } + if (offset == UART_LCR && !d->uart_16550_compatible) + dw8250_check_lcr(p, value); } #endif /* CONFIG_64BIT */ static void dw8250_serial_out32(struct uart_port *p, int offset, int value) { + struct dw8250_data *d = p->private_data; + writel(value, p->membase + (offset << p->regshift)); - /* Make sure LCR write wasn't ignored */ - if (offset == UART_LCR) { - int tries = 1000; - while (tries--) { - unsigned int lcr = p->serial_in(p, UART_LCR); - if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR)) - return; - dw8250_force_idle(p); - writel(value, p->membase + (UART_LCR << p->regshift)); - } - /* - * FIXME: this deadlocks if port->lock is already held - * dev_err(p->dev, "Couldn't set LCR to %d\n", value); - */ - } + if (offset == UART_LCR && !d->uart_16550_compatible) + dw8250_check_lcr(p, value); } static unsigned int dw8250_serial_in32(struct uart_port *p, int offset) @@ -187,14 +178,33 @@ static unsigned int dw8250_serial_in32(struct uart_port *p, int offset) return dw8250_modify_msr(p, offset, value); } +static void dw8250_serial_out32be(struct uart_port *p, int offset, int value) +{ + struct dw8250_data *d = p->private_data; + + iowrite32be(value, p->membase + (offset << p->regshift)); + + if (offset == UART_LCR && !d->uart_16550_compatible) + dw8250_check_lcr(p, value); +} + +static unsigned int dw8250_serial_in32be(struct uart_port *p, int offset) +{ + unsigned int value = ioread32be(p->membase + (offset << p->regshift)); + + return dw8250_modify_msr(p, offset, value); +} + + static int dw8250_handle_irq(struct uart_port *p) { struct dw8250_data *d = p->private_data; unsigned int iir = p->serial_in(p, UART_IIR); - if (serial8250_handle_irq(p, iir)) { + if (serial8250_handle_irq(p, iir)) return 1; - } else if ((iir & UART_IIR_BUSY) == UART_IIR_BUSY) { + + if ((iir & UART_IIR_BUSY) == UART_IIR_BUSY) { /* Clear the USR */ (void)p->serial_in(p, d->usr_reg); @@ -281,6 +291,11 @@ static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data) data->skip_autocfg = true; } #endif + if (of_device_is_big_endian(p->dev->of_node)) { + p->iotype = UPIO_MEM32BE; + p->serial_in = dw8250_serial_in32be; + p->serial_out = dw8250_serial_out32be; + } } else if (has_acpi_companion(p->dev)) { p->iotype = UPIO_MEM32; p->regshift = 2; @@ -309,14 +324,20 @@ static void dw8250_setup_port(struct uart_port *p) * If the Component Version Register returns zero, we know that * ADDITIONAL_FEATURES are not enabled. No need to go any further. */ - reg = readl(p->membase + DW_UART_UCV); + if (p->iotype == UPIO_MEM32BE) + reg = ioread32be(p->membase + DW_UART_UCV); + else + reg = readl(p->membase + DW_UART_UCV); if (!reg) return; dev_dbg(p->dev, "Designware UART version %c.%c%c\n", (reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff); - reg = readl(p->membase + DW_UART_CPR); + if (p->iotype == UPIO_MEM32BE) + reg = ioread32be(p->membase + DW_UART_CPR); + else + reg = readl(p->membase + DW_UART_CPR); if (!reg) return; @@ -463,10 +484,8 @@ static int dw8250_probe(struct platform_device *pdev) dw8250_quirks(p, data); /* If the Busy Functionality is not implemented, don't handle it */ - if (data->uart_16550_compatible) { - p->serial_out = NULL; + if (data->uart_16550_compatible) p->handle_irq = NULL; - } if (!data->skip_autocfg) dw8250_setup_port(p); diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c index af62131af21e..8d08ff5c4e34 100644 --- a/drivers/tty/serial/8250/8250_early.c +++ b/drivers/tty/serial/8250/8250_early.c @@ -39,15 +39,17 @@ static unsigned int __init serial8250_early_in(struct uart_port *port, int offset) { + offset <<= port->regshift; + switch (port->iotype) { case UPIO_MEM: return readb(port->membase + offset); case UPIO_MEM16: - return readw(port->membase + (offset << 1)); + return readw(port->membase + offset); case UPIO_MEM32: - return readl(port->membase + (offset << 2)); + return readl(port->membase + offset); case UPIO_MEM32BE: - return ioread32be(port->membase + (offset << 2)); + return ioread32be(port->membase + offset); case UPIO_PORT: return inb(port->iobase + offset); default: @@ -57,18 +59,20 @@ static unsigned int __init serial8250_early_in(struct uart_port *port, int offse static void __init serial8250_early_out(struct uart_port *port, int offset, int value) { + offset <<= port->regshift; + switch (port->iotype) { case UPIO_MEM: writeb(value, port->membase + offset); break; case UPIO_MEM16: - writew(value, port->membase + (offset << 1)); + writew(value, port->membase + offset); break; case UPIO_MEM32: - writel(value, port->membase + (offset << 2)); + writel(value, port->membase + offset); break; case UPIO_MEM32BE: - iowrite32be(value, port->membase + (offset << 2)); + iowrite32be(value, port->membase + offset); break; case UPIO_PORT: outb(value, port->iobase + offset); @@ -145,3 +149,25 @@ EARLYCON_DECLARE(uart8250, early_serial8250_setup); EARLYCON_DECLARE(uart, early_serial8250_setup); OF_EARLYCON_DECLARE(ns16550, "ns16550", early_serial8250_setup); OF_EARLYCON_DECLARE(ns16550a, "ns16550a", early_serial8250_setup); +OF_EARLYCON_DECLARE(uart, "nvidia,tegra20-uart", early_serial8250_setup); + +#ifdef CONFIG_SERIAL_8250_OMAP + +static int __init early_omap8250_setup(struct earlycon_device *device, + const char *options) +{ + struct uart_port *port = &device->port; + + if (!(device->port.membase || device->port.iobase)) + return -ENODEV; + + port->regshift = 2; + device->con->write = early_serial8250_write; + return 0; +} + +OF_EARLYCON_DECLARE(omap8250, "ti,omap2-uart", early_omap8250_setup); +OF_EARLYCON_DECLARE(omap8250, "ti,omap3-uart", early_omap8250_setup); +OF_EARLYCON_DECLARE(omap8250, "ti,omap4-uart", early_omap8250_setup); + +#endif diff --git a/drivers/tty/serial/8250/8250_exar_st16c554.c b/drivers/tty/serial/8250/8250_exar_st16c554.c index bf53aabf9b5e..3a7cb8262bb9 100644 --- a/drivers/tty/serial/8250/8250_exar_st16c554.c +++ b/drivers/tty/serial/8250/8250_exar_st16c554.c @@ -13,20 +13,13 @@ #include <linux/init.h> #include <linux/serial_8250.h> -#define PORT(_base,_irq) \ - { \ - .iobase = _base, \ - .irq = _irq, \ - .uartclk = 1843200, \ - .iotype = UPIO_PORT, \ - .flags = UPF_BOOT_AUTOCONF, \ - } +#include "8250.h" static struct plat_serial8250_port exar_data[] = { - PORT(0x100, 5), - PORT(0x108, 5), - PORT(0x110, 5), - PORT(0x118, 5), + SERIAL8250_PORT(0x100, 5), + SERIAL8250_PORT(0x108, 5), + SERIAL8250_PORT(0x110, 5), + SERIAL8250_PORT(0x118, 5), { }, }; diff --git a/drivers/tty/serial/8250/8250_fourport.c b/drivers/tty/serial/8250/8250_fourport.c index be1582609626..4045180a8cfc 100644 --- a/drivers/tty/serial/8250/8250_fourport.c +++ b/drivers/tty/serial/8250/8250_fourport.c @@ -10,24 +10,20 @@ #include <linux/init.h> #include <linux/serial_8250.h> -#define PORT(_base,_irq) \ - { \ - .iobase = _base, \ - .irq = _irq, \ - .uartclk = 1843200, \ - .iotype = UPIO_PORT, \ - .flags = UPF_BOOT_AUTOCONF | UPF_FOURPORT, \ - } +#include "8250.h" + +#define SERIAL8250_FOURPORT(_base, _irq) \ + SERIAL8250_PORT_FLAGS(_base, _irq, UPF_FOURPORT) static struct plat_serial8250_port fourport_data[] = { - PORT(0x1a0, 9), - PORT(0x1a8, 9), - PORT(0x1b0, 9), - PORT(0x1b8, 9), - PORT(0x2a0, 5), - PORT(0x2a8, 5), - PORT(0x2b0, 5), - PORT(0x2b8, 5), + SERIAL8250_FOURPORT(0x1a0, 9), + SERIAL8250_FOURPORT(0x1a8, 9), + SERIAL8250_FOURPORT(0x1b0, 9), + SERIAL8250_FOURPORT(0x1b8, 9), + SERIAL8250_FOURPORT(0x2a0, 5), + SERIAL8250_FOURPORT(0x2a8, 5), + SERIAL8250_FOURPORT(0x2b0, 5), + SERIAL8250_FOURPORT(0x2b8, 5), { }, }; diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c index 2e3ea1a70d7b..b1e6ae9f1ff9 100644 --- a/drivers/tty/serial/8250/8250_gsc.c +++ b/drivers/tty/serial/8250/8250_gsc.c @@ -42,7 +42,7 @@ static int __init serial_init_chip(struct parisc_device *dev) * the user what they're missing. */ if (parisc_parent(dev)->id.hw_type != HPHW_IOA) - printk(KERN_INFO + dev_info(&dev->dev, "Serial: device 0x%llx not configured.\n" "Enable support for Wax, Lasi, Asp or Dino.\n", (unsigned long long)dev->hpa.start); @@ -66,8 +66,9 @@ static int __init serial_init_chip(struct parisc_device *dev) err = serial8250_register_8250_port(&uart); if (err < 0) { - printk(KERN_WARNING - "serial8250_register_8250_port returned error %d\n", err); + dev_warn(&dev->dev, + "serial8250_register_8250_port returned error %d\n", + err); iounmap(uart.port.membase); return err; } diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c index 2891958cd842..38166db2b824 100644 --- a/drivers/tty/serial/8250/8250_hp300.c +++ b/drivers/tty/serial/8250/8250_hp300.c @@ -24,8 +24,7 @@ #endif #ifdef CONFIG_HPAPCI -struct hp300_port -{ +struct hp300_port { struct hp300_port *next; /* next port */ int line; /* line (tty) number */ }; @@ -111,7 +110,7 @@ int __init hp300_setup_serial_console(void) /* Check for APCI console */ if (scode == 256) { #ifdef CONFIG_HPAPCI - printk(KERN_INFO "Serial console is HP APCI 1\n"); + pr_info("Serial console is HP APCI 1\n"); port.uartclk = HPAPCI_BAUD_BASE * 16; port.mapbase = (FRODO_BASE + FRODO_APCI_OFFSET(1)); @@ -119,7 +118,7 @@ int __init hp300_setup_serial_console(void) port.regshift = 2; add_preferred_console("ttyS", port.line, "9600n8"); #else - printk(KERN_WARNING "Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n"); + pr_warn("Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n"); return 0; #endif } else { @@ -128,7 +127,7 @@ int __init hp300_setup_serial_console(void) if (!pa) return 0; - printk(KERN_INFO "Serial console is HP DCA at select code %d\n", scode); + pr_info("Serial console is HP DCA at select code %d\n", scode); port.uartclk = HPDCA_BAUD_BASE * 16; port.mapbase = (pa + UART_OFFSET); @@ -142,13 +141,13 @@ int __init hp300_setup_serial_console(void) if (DIO_ID(pa + DIO_VIRADDRBASE) & 0x80) add_preferred_console("ttyS", port.line, "9600n8"); #else - printk(KERN_WARNING "Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n"); + pr_warn("Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n"); return 0; #endif } if (early_serial_setup(&port) < 0) - printk(KERN_WARNING "hp300_setup_serial_console(): early_serial_setup() failed.\n"); + pr_warn("%s: early_serial_setup() failed.\n", __func__); return 0; } #endif /* CONFIG_SERIAL_8250_CONSOLE */ @@ -180,8 +179,9 @@ static int hpdca_init_one(struct dio_dev *d, line = serial8250_register_8250_port(&uart); if (line < 0) { - printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d" - " irq %d failed\n", d->scode, uart.port.irq); + dev_notice(&d->dev, + "8250_hp300: register_serial() DCA scode %d irq %d failed\n", + d->scode, uart.port.irq); return -ENOMEM; } @@ -249,8 +249,8 @@ static int __init hp300_8250_init(void) /* Memory mapped I/O */ uart.port.iotype = UPIO_MEM; - uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \ - | UPF_BOOT_AUTOCONF; + uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ + | UPF_BOOT_AUTOCONF; /* XXX - no interrupt support yet */ uart.port.irq = 0; uart.port.uartclk = HPAPCI_BAUD_BASE * 16; @@ -261,8 +261,9 @@ static int __init hp300_8250_init(void) line = serial8250_register_8250_port(&uart); if (line < 0) { - printk(KERN_NOTICE "8250_hp300: register_serial() APCI" - " %d irq %d failed\n", i, uart.port.irq); + dev_notice(uart.port.dev, + "8250_hp300: register_serial() APCI %d irq %d failed\n", + i, uart.port.irq); kfree(port); continue; } diff --git a/drivers/tty/serial/8250/8250_hub6.c b/drivers/tty/serial/8250/8250_hub6.c index a5c778e83de0..27124e21eb96 100644 --- a/drivers/tty/serial/8250/8250_hub6.c +++ b/drivers/tty/serial/8250/8250_hub6.c @@ -10,7 +10,7 @@ #include <linux/init.h> #include <linux/serial_8250.h> -#define HUB6(card,port) \ +#define HUB6(card, port) \ { \ .iobase = 0x302, \ .irq = 3, \ diff --git a/drivers/tty/serial/8250/8250_ingenic.c b/drivers/tty/serial/8250/8250_ingenic.c index d6e1ec9b4fde..b0677f610863 100644 --- a/drivers/tty/serial/8250/8250_ingenic.c +++ b/drivers/tty/serial/8250/8250_ingenic.c @@ -48,7 +48,7 @@ static const struct of_device_id of_match[]; #define UART_MCR_MDCE BIT(7) #define UART_MCR_FCM BIT(6) -#ifdef CONFIG_SERIAL_EARLYCON +#if defined(CONFIG_SERIAL_EARLYCON) && !defined(MODULE) static struct earlycon_device *early_device; static uint8_t __init early_in(struct uart_port *port, int offset) @@ -154,14 +154,18 @@ static void ingenic_uart_serial_out(struct uart_port *p, int offset, int value) break; case UART_IER: - /* Enable receive timeout interrupt with the - * receive line status interrupt */ + /* + * Enable receive timeout interrupt with the receive line + * status interrupt. + */ value |= (value & 0x4) << 2; break; case UART_MCR: - /* If we have enabled modem status IRQs we should enable modem - * mode. */ + /* + * If we have enabled modem status IRQs we should enable + * modem mode. + */ ier = p->serial_in(p, UART_IER); if (ier & UART_IER_MSI) diff --git a/drivers/tty/serial/8250/8250_moxa.c b/drivers/tty/serial/8250/8250_moxa.c new file mode 100644 index 000000000000..26eb5393a263 --- /dev/null +++ b/drivers/tty/serial/8250/8250_moxa.c @@ -0,0 +1,157 @@ +/* + * 8250_moxa.c - MOXA Smartio/Industio MUE multiport serial driver. + * + * Author: Mathieu OTHACEHE <m.othacehe@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/pci.h> + +#include "8250.h" + +#define PCI_DEVICE_ID_MOXA_CP102E 0x1024 +#define PCI_DEVICE_ID_MOXA_CP102EL 0x1025 +#define PCI_DEVICE_ID_MOXA_CP104EL_A 0x1045 +#define PCI_DEVICE_ID_MOXA_CP114EL 0x1144 +#define PCI_DEVICE_ID_MOXA_CP116E_A_A 0x1160 +#define PCI_DEVICE_ID_MOXA_CP116E_A_B 0x1161 +#define PCI_DEVICE_ID_MOXA_CP118EL_A 0x1182 +#define PCI_DEVICE_ID_MOXA_CP118E_A_I 0x1183 +#define PCI_DEVICE_ID_MOXA_CP132EL 0x1322 +#define PCI_DEVICE_ID_MOXA_CP134EL_A 0x1342 +#define PCI_DEVICE_ID_MOXA_CP138E_A 0x1381 +#define PCI_DEVICE_ID_MOXA_CP168EL_A 0x1683 + +#define MOXA_BASE_BAUD 921600 +#define MOXA_UART_OFFSET 0x200 +#define MOXA_BASE_BAR 1 + +struct moxa8250_board { + unsigned int num_ports; + int line[0]; +}; + +enum { + moxa8250_2p = 0, + moxa8250_4p, + moxa8250_8p +}; + +static struct moxa8250_board moxa8250_boards[] = { + [moxa8250_2p] = { .num_ports = 2}, + [moxa8250_4p] = { .num_ports = 4}, + [moxa8250_8p] = { .num_ports = 8}, +}; + +static int moxa8250_probe(struct pci_dev *pdev, const struct pci_device_id *id) +{ + struct uart_8250_port uart; + struct moxa8250_board *brd; + void __iomem *ioaddr; + resource_size_t baseaddr; + unsigned int i, nr_ports; + unsigned int offset; + int ret; + + brd = &moxa8250_boards[id->driver_data]; + nr_ports = brd->num_ports; + + ret = pcim_enable_device(pdev); + if (ret) + return ret; + + brd = devm_kzalloc(&pdev->dev, sizeof(struct moxa8250_board) + + sizeof(unsigned int) * nr_ports, GFP_KERNEL); + if (!brd) + return -ENOMEM; + + memset(&uart, 0, sizeof(struct uart_8250_port)); + + uart.port.dev = &pdev->dev; + uart.port.irq = pdev->irq; + uart.port.uartclk = MOXA_BASE_BAUD * 16; + uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ; + + baseaddr = pci_resource_start(pdev, MOXA_BASE_BAR); + ioaddr = pcim_iomap(pdev, MOXA_BASE_BAR, 0); + if (!ioaddr) + return -ENOMEM; + + for (i = 0; i < nr_ports; i++) { + + /* + * MOXA Smartio MUE boards with 4 ports have + * a different offset for port #3 + */ + if (nr_ports == 4 && i == 3) + offset = 7 * MOXA_UART_OFFSET; + else + offset = i * MOXA_UART_OFFSET; + + uart.port.iotype = UPIO_MEM; + uart.port.iobase = 0; + uart.port.mapbase = baseaddr + offset; + uart.port.membase = ioaddr + offset; + uart.port.regshift = 0; + + dev_dbg(&pdev->dev, "Setup PCI port: port %lx, irq %d, type %d\n", + uart.port.iobase, uart.port.irq, uart.port.iotype); + + brd->line[i] = serial8250_register_8250_port(&uart); + if (brd->line[i] < 0) { + dev_err(&pdev->dev, + "Couldn't register serial port %lx, irq %d, type %d, error %d\n", + uart.port.iobase, uart.port.irq, + uart.port.iotype, brd->line[i]); + break; + } + } + + pci_set_drvdata(pdev, brd); + return 0; +} + +static void moxa8250_remove(struct pci_dev *pdev) +{ + struct moxa8250_board *brd = pci_get_drvdata(pdev); + unsigned int i; + + for (i = 0; i < brd->num_ports; i++) + serial8250_unregister_port(brd->line[i]); +} + +#define MOXA_DEVICE(id, data) { PCI_VDEVICE(MOXA, id), (kernel_ulong_t)data } + +static const struct pci_device_id pci_ids[] = { + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP102E, moxa8250_2p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP102EL, moxa8250_2p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP104EL_A, moxa8250_4p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP114EL, moxa8250_4p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP116E_A_A, moxa8250_8p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP116E_A_B, moxa8250_8p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP118EL_A, moxa8250_8p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP118E_A_I, moxa8250_8p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP132EL, moxa8250_2p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP134EL_A, moxa8250_4p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP138E_A, moxa8250_8p), + MOXA_DEVICE(PCI_DEVICE_ID_MOXA_CP168EL_A, moxa8250_8p), + {0} +}; +MODULE_DEVICE_TABLE(pci, pci_ids); + +static struct pci_driver moxa8250_pci_driver = { + .name = "8250_moxa", + .id_table = pci_ids, + .probe = moxa8250_probe, + .remove = moxa8250_remove, +}; + +module_pci_driver(moxa8250_pci_driver); + +MODULE_AUTHOR("Mathieu OTHACEHE"); +MODULE_DESCRIPTION("MOXA SmartIO MUE driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index 0e590b233f03..3489fbcb7313 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -16,7 +16,7 @@ */ #include <linux/clk.h> #include <linux/io.h> -#include <linux/init.h> +#include <linux/module.h> #include <linux/of_irq.h> #include <linux/of_platform.h> #include <linux/platform_device.h> @@ -41,12 +41,10 @@ static void mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { + struct uart_8250_port *up = up_to_u8250p(port); unsigned long flags; unsigned int baud, quot; - struct uart_8250_port *up = - container_of(port, struct uart_8250_port, port); - serial8250_do_set_termios(port, termios, old); /* @@ -116,7 +114,7 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, tty_termios_encode_baud_rate(termios, baud, baud); } -static int mtk8250_runtime_suspend(struct device *dev) +static int __maybe_unused mtk8250_runtime_suspend(struct device *dev) { struct mtk8250_data *data = dev_get_drvdata(dev); @@ -126,7 +124,7 @@ static int mtk8250_runtime_suspend(struct device *dev) return 0; } -static int mtk8250_runtime_resume(struct device *dev) +static int __maybe_unused mtk8250_runtime_resume(struct device *dev) { struct mtk8250_data *data = dev_get_drvdata(dev); int err; @@ -245,8 +243,24 @@ static int mtk8250_probe(struct platform_device *pdev) return 0; } -#ifdef CONFIG_PM_SLEEP -static int mtk8250_suspend(struct device *dev) +static int mtk8250_remove(struct platform_device *pdev) +{ + struct mtk8250_data *data = platform_get_drvdata(pdev); + + pm_runtime_get_sync(&pdev->dev); + + serial8250_unregister_port(data->line); + + pm_runtime_disable(&pdev->dev); + pm_runtime_put_noidle(&pdev->dev); + + if (!pm_runtime_status_suspended(&pdev->dev)) + mtk8250_runtime_suspend(&pdev->dev); + + return 0; +} + +static int __maybe_unused mtk8250_suspend(struct device *dev) { struct mtk8250_data *data = dev_get_drvdata(dev); @@ -255,7 +269,7 @@ static int mtk8250_suspend(struct device *dev) return 0; } -static int mtk8250_resume(struct device *dev) +static int __maybe_unused mtk8250_resume(struct device *dev) { struct mtk8250_data *data = dev_get_drvdata(dev); @@ -263,7 +277,6 @@ static int mtk8250_resume(struct device *dev) return 0; } -#endif /* CONFIG_PM_SLEEP */ static const struct dev_pm_ops mtk8250_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume) @@ -275,20 +288,20 @@ static const struct of_device_id mtk8250_of_match[] = { { .compatible = "mediatek,mt6577-uart" }, { /* Sentinel */ } }; +MODULE_DEVICE_TABLE(of, mtk8250_of_match); static struct platform_driver mtk8250_platform_driver = { .driver = { - .name = "mt6577-uart", - .pm = &mtk8250_pm_ops, - .of_match_table = mtk8250_of_match, - .suppress_bind_attrs = true, - + .name = "mt6577-uart", + .pm = &mtk8250_pm_ops, + .of_match_table = mtk8250_of_match, }, .probe = mtk8250_probe, + .remove = mtk8250_remove, }; -builtin_platform_driver(mtk8250_platform_driver); +module_platform_driver(mtk8250_platform_driver); -#ifdef CONFIG_SERIAL_8250_CONSOLE +#if defined(CONFIG_SERIAL_8250_CONSOLE) && !defined(MODULE) static int __init early_mtk8250_setup(struct earlycon_device *device, const char *options) { @@ -302,3 +315,7 @@ static int __init early_mtk8250_setup(struct earlycon_device *device, OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup); #endif + +MODULE_AUTHOR("Matthias Brugger"); +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Mediatek 8250 serial port driver"); diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c index 33021c1f7d55..c7ed3d2bc8b2 100644 --- a/drivers/tty/serial/8250/8250_of.c +++ b/drivers/tty/serial/8250/8250_of.c @@ -335,6 +335,7 @@ static struct platform_driver of_platform_serial_driver = { .driver = { .name = "of_serial", .of_match_table = of_platform_serial_table, + .pm = &of_serial_pm_ops, }, .probe = of_platform_serial_probe, .remove = of_platform_serial_remove, diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index a2c0734c76e2..6f760510e46d 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -318,8 +318,7 @@ static void omap_8250_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { - struct uart_8250_port *up = - container_of(port, struct uart_8250_port, port); + struct uart_8250_port *up = up_to_u8250p(port); struct omap8250_priv *priv = up->port.private_data; unsigned char cval = 0; unsigned int baud; @@ -682,9 +681,8 @@ static void omap_8250_shutdown(struct uart_port *port) static void omap_8250_throttle(struct uart_port *port) { + struct uart_8250_port *up = up_to_u8250p(port); unsigned long flags; - struct uart_8250_port *up = - container_of(port, struct uart_8250_port, port); pm_runtime_get_sync(port->dev); @@ -697,11 +695,40 @@ static void omap_8250_throttle(struct uart_port *port) pm_runtime_put_autosuspend(port->dev); } +static int omap_8250_rs485_config(struct uart_port *port, + struct serial_rs485 *rs485) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + /* Clamp the delays to [0, 100ms] */ + rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 100U); + rs485->delay_rts_after_send = min(rs485->delay_rts_after_send, 100U); + + port->rs485 = *rs485; + + /* + * Both serial8250_em485_init and serial8250_em485_destroy + * are idempotent + */ + if (rs485->flags & SER_RS485_ENABLED) { + int ret = serial8250_em485_init(up); + + if (ret) { + rs485->flags &= ~SER_RS485_ENABLED; + port->rs485.flags &= ~SER_RS485_ENABLED; + } + return ret; + } + + serial8250_em485_destroy(up); + + return 0; +} + static void omap_8250_unthrottle(struct uart_port *port) { + struct uart_8250_port *up = up_to_u8250p(port); unsigned long flags; - struct uart_8250_port *up = - container_of(port, struct uart_8250_port, port); pm_runtime_get_sync(port->dev); @@ -1146,6 +1173,7 @@ static int omap8250_probe(struct platform_device *pdev) up.port.shutdown = omap_8250_shutdown; up.port.throttle = omap_8250_throttle; up.port.unthrottle = omap_8250_unthrottle; + up.port.rs485_config = omap_8250_rs485_config; if (pdev->dev.of_node) { const struct of_device_id *id; diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 7cd6f9a90542..98862aa5bb58 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -55,7 +55,6 @@ struct pci_serial_quirk { struct serial_private { struct pci_dev *dev; unsigned int nr; - void __iomem *remapped_bar[PCI_NUM_BAR_RESOURCES]; struct pci_serial_quirk *quirk; int line[0]; }; @@ -85,15 +84,13 @@ setup_port(struct serial_private *priv, struct uart_8250_port *port, return -EINVAL; if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) { - if (!priv->remapped_bar[bar]) - priv->remapped_bar[bar] = pci_ioremap_bar(dev, bar); - if (!priv->remapped_bar[bar]) + if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev)) return -ENOMEM; port->port.iotype = UPIO_MEM; port->port.iobase = 0; port->port.mapbase = pci_resource_start(dev, bar) + offset; - port->port.membase = priv->remapped_bar[bar] + offset; + port->port.membase = pcim_iomap_table(dev)[bar] + offset; port->port.regshift = regshift; } else { port->port.iotype = UPIO_PORT; @@ -721,7 +718,7 @@ static int pci_ni8430_init(struct pci_dev *dev) */ pcibios_resource_to_bus(dev->bus, ®ion, &dev->resource[bar]); device_window = ((region.start + MITE_IOWBSR1_WIN_OFFSET) & 0xffffff00) - | MITE_IOWBSR1_WENAB | MITE_IOWBSR1_WSIZE; + | MITE_IOWBSR1_WENAB | MITE_IOWBSR1_WSIZE; writel(device_window, p + MITE_IOWBSR1); /* Set window access to go to RAMSEL IO address space */ @@ -803,12 +800,12 @@ static int pci_netmos_9900_numports(struct pci_dev *dev) unsigned int pi; unsigned short sub_serports; - pi = (c & 0xff); + pi = c & 0xff; - if (pi == 2) { + if (pi == 2) return 1; - } else if ((pi == 0) && - (dev->device == PCI_DEVICE_ID_NETMOS_9900)) { + + if ((pi == 0) && (dev->device == PCI_DEVICE_ID_NETMOS_9900)) { /* two possibilities: 0x30ps encodes number of parallel and * serial ports, or 0x1000 indicates *something*. This is not * immediately obvious, since the 2s1p+4s configuration seems @@ -816,12 +813,12 @@ static int pci_netmos_9900_numports(struct pci_dev *dev) * advertising the same function 3 as the 4s+2s1p config. */ sub_serports = dev->subsystem_device & 0xf; - if (sub_serports > 0) { + if (sub_serports > 0) return sub_serports; - } else { - dev_err(&dev->dev, "NetMos/Mostech serial driver ignoring port on ambiguous config.\n"); - return 0; - } + + dev_err(&dev->dev, + "NetMos/Mostech serial driver ignoring port on ambiguous config.\n"); + return 0; } moan_device("unknown NetMos/Mostech program interface", dev); @@ -842,21 +839,21 @@ static int pci_netmos_init(struct pci_dev *dev) return 0; switch (dev->device) { /* FALLTHROUGH on all */ - case PCI_DEVICE_ID_NETMOS_9904: - case PCI_DEVICE_ID_NETMOS_9912: - case PCI_DEVICE_ID_NETMOS_9922: - case PCI_DEVICE_ID_NETMOS_9900: - num_serial = pci_netmos_9900_numports(dev); - break; + case PCI_DEVICE_ID_NETMOS_9904: + case PCI_DEVICE_ID_NETMOS_9912: + case PCI_DEVICE_ID_NETMOS_9922: + case PCI_DEVICE_ID_NETMOS_9900: + num_serial = pci_netmos_9900_numports(dev); + break; - default: - if (num_serial == 0 ) { - moan_device("unknown NetMos/Mostech device", dev); - } + default: + break; } - if (num_serial == 0) + if (num_serial == 0) { + moan_device("unknown NetMos/Mostech device", dev); return -ENODEV; + } return num_serial; } @@ -1198,8 +1195,9 @@ static int pci_quatech_has_qmcr(struct uart_8250_port *port) static int pci_quatech_test(struct uart_8250_port *port) { - u8 reg; - u8 qopr = pci_quatech_rqopr(port); + u8 reg, qopr; + + qopr = pci_quatech_rqopr(port); pci_quatech_wqopr(port, qopr & QPCR_TEST_FOR1); reg = pci_quatech_rqopr(port) & 0xC0; if (reg != QPCR_TEST_GET1) @@ -1286,6 +1284,7 @@ static int pci_quatech_init(struct pci_dev *dev) unsigned long base = pci_resource_start(dev, 0); if (base) { u32 tmp; + outl(inl(base + 0x38) | 0x00002000, base + 0x38); tmp = inl(base + 0x3c); outl(tmp | 0x01000000, base + 0x3c); @@ -1334,29 +1333,6 @@ static int pci_default_setup(struct serial_private *priv, return setup_port(priv, port, bar, offset, board->reg_shift); } -static int pci_pericom_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx) -{ - unsigned int bar, offset = board->first_offset, maxnr; - - bar = FL_GET_BASE(board->flags); - if (board->flags & FL_BASE_BARS) - bar += idx; - else - offset += idx * board->uart_offset; - - maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) >> - (board->reg_shift + 3); - - if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr) - return 1; - - port->port.uartclk = 14745600; - - return setup_port(priv, port, bar, offset, board->reg_shift); -} - static int ce4100_serial_setup(struct serial_private *priv, const struct pciserial_board *board, @@ -1541,10 +1517,9 @@ pci_brcm_trumanage_setup(struct serial_private *priv, static int pci_fintek_rs485_config(struct uart_port *port, struct serial_rs485 *rs485) { + struct pci_dev *pci_dev = to_pci_dev(port->dev); u8 setting; u8 *index = (u8 *) port->private_data; - struct pci_dev *pci_dev = container_of(port->dev, struct pci_dev, - dev); pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting); @@ -1766,7 +1741,7 @@ xr17v35x_has_slave(struct serial_private *priv) const int dev_id = priv->dev->device; return ((dev_id == PCI_DEVICE_ID_EXAR_XR17V4358) || - (dev_id == PCI_DEVICE_ID_EXAR_XR17V8358)); + (dev_id == PCI_DEVICE_ID_EXAR_XR17V8358)); } static int @@ -1866,8 +1841,8 @@ pci_fastcom335_setup(struct serial_private *priv, static int pci_wch_ch353_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx) + const struct pciserial_board *board, + struct uart_8250_port *port, int idx) { port->port.flags |= UPF_FIXED_TYPE; port->port.type = PORT_16550A; @@ -1876,8 +1851,8 @@ pci_wch_ch353_setup(struct serial_private *priv, static int pci_wch_ch38x_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx) + const struct pciserial_board *board, + struct uart_8250_port *port, int idx) { port->port.flags |= UPF_FIXED_TYPE; port->port.type = PORT_16850; @@ -2246,16 +2221,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .exit = pci_plx9050_exit, }, /* - * Pericom - */ - { - .vendor = PCI_VENDOR_ID_PERICOM, - .device = PCI_ANY_ID, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, - }, - /* * PLX */ { @@ -3733,15 +3698,10 @@ static struct pciserial_board pci_boards[] = { .base_baud = 921600, .reg_shift = 2, }, - /* - * Intel BayTrail HSUART reference clock is 44.2368 MHz at power-on, - * but is overridden by byt_set_termios. - */ [pbn_byt] = { .flags = FL_BASE0, .num_ports = 1, .base_baud = 2764800, - .uart_offset = 0x80, .reg_shift = 2, }, [pbn_qrk] = { @@ -3840,6 +3800,20 @@ static const struct pci_device_id blacklist[] = { { PCI_DEVICE(0x1c00, 0x3250), }, /* WCH CH382 2S1P */ { PCI_DEVICE(0x1c00, 0x3470), }, /* WCH CH384 4S */ + /* Moxa Smartio MUE boards handled by 8250_moxa */ + { PCI_VDEVICE(MOXA, 0x1024), }, + { PCI_VDEVICE(MOXA, 0x1025), }, + { PCI_VDEVICE(MOXA, 0x1045), }, + { PCI_VDEVICE(MOXA, 0x1144), }, + { PCI_VDEVICE(MOXA, 0x1160), }, + { PCI_VDEVICE(MOXA, 0x1161), }, + { PCI_VDEVICE(MOXA, 0x1182), }, + { PCI_VDEVICE(MOXA, 0x1183), }, + { PCI_VDEVICE(MOXA, 0x1322), }, + { PCI_VDEVICE(MOXA, 0x1342), }, + { PCI_VDEVICE(MOXA, 0x1381), }, + { PCI_VDEVICE(MOXA, 0x1683), }, + /* Intel platforms with MID UART */ { PCI_VDEVICE(INTEL, 0x081b), }, { PCI_VDEVICE(INTEL, 0x081c), }, @@ -4027,12 +4001,6 @@ void pciserial_remove_ports(struct serial_private *priv) for (i = 0; i < priv->nr; i++) serial8250_unregister_port(priv->line[i]); - for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) { - if (priv->remapped_bar[i]) - iounmap(priv->remapped_bar[i]); - priv->remapped_bar[i] = NULL; - } - /* * Find the exit quirks. */ @@ -4104,7 +4072,7 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent) board = &pci_boards[ent->driver_data]; - rc = pci_enable_device(dev); + rc = pcim_enable_device(dev); pci_save_state(dev); if (rc) return rc; @@ -4123,7 +4091,7 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent) */ rc = serial_pci_guess_board(dev, &tmp); if (rc) - goto disable; + return rc; } else { /* * We matched an explicit entry. If we are able to @@ -4139,16 +4107,11 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent) } priv = pciserial_init_ports(dev, board); - if (!IS_ERR(priv)) { - pci_set_drvdata(dev, priv); - return 0; - } + if (IS_ERR(priv)) + return PTR_ERR(priv); - rc = PTR_ERR(priv); - - disable: - pci_disable_device(dev); - return rc; + pci_set_drvdata(dev, priv); + return 0; } static void pciserial_remove_one(struct pci_dev *dev) @@ -4156,8 +4119,6 @@ static void pciserial_remove_one(struct pci_dev *dev) struct serial_private *priv = pci_get_drvdata(dev); pciserial_remove_ports(priv); - - pci_disable_device(dev); } #ifdef CONFIG_PM_SLEEP @@ -4538,7 +4499,7 @@ static struct pci_device_id serial_pci_tbl[] = { PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b0_bt_2_921600 }, { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI958, - PCI_ANY_ID , PCI_ANY_ID, 0, 0, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b2_8_1152000 }, /* diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c index 658b392d1170..34f05ed78b68 100644 --- a/drivers/tty/serial/8250/8250_pnp.c +++ b/drivers/tty/serial/8250/8250_pnp.c @@ -357,8 +357,8 @@ static const struct pnp_device_id pnp_dev_table[] = { /* Fujitsu Wacom 1FGT Tablet PC device */ { "FUJ02E9", 0 }, /* - * LG C1 EXPRESS DUAL (C1-PB11A3) touch screen (actually a FUJ02E6 in - * disguise) + * LG C1 EXPRESS DUAL (C1-PB11A3) touch screen (actually a FUJ02E6 + * in disguise). */ { "LTS0001", 0 }, /* Rockwell's (PORALiNK) 33600 INT PNP */ @@ -367,12 +367,14 @@ static const struct pnp_device_id pnp_dev_table[] = { { "PNPCXXX", UNKNOWN_DEV }, /* More unknown PnP modems */ { "PNPDXXX", UNKNOWN_DEV }, - /* Winbond CIR port, should not be probed. We should keep track - of it to prevent the legacy serial driver from probing it */ + /* + * Winbond CIR port, should not be probed. We should keep track of + * it to prevent the legacy serial driver from probing it. + */ { "WEC1022", CIR_PORT }, /* - * SMSC IrCC SIR/FIR port, should not be probed by serial driver - * as well so its own driver can bind to it. + * SMSC IrCC SIR/FIR port, should not be probed by serial driver as + * well so its own driver can bind to it. */ { "SMCF010", CIR_PORT }, { "", 0 } @@ -380,35 +382,35 @@ static const struct pnp_device_id pnp_dev_table[] = { MODULE_DEVICE_TABLE(pnp, pnp_dev_table); -static char *modem_names[] = { +static const char *modem_names[] = { "MODEM", "Modem", "modem", "FAX", "Fax", "fax", "56K", "56k", "K56", "33.6", "28.8", "14.4", "33,600", "28,800", "14,400", "33.600", "28.800", "14.400", "33600", "28800", "14400", "V.90", "V.34", "V.32", NULL }; -static int check_name(char *name) +static bool check_name(const char *name) { - char **tmp; + const char **tmp; for (tmp = modem_names; *tmp; tmp++) if (strstr(name, *tmp)) - return 1; + return true; - return 0; + return false; } -static int check_resources(struct pnp_dev *dev) +static bool check_resources(struct pnp_dev *dev) { - resource_size_t base[] = {0x2f8, 0x3f8, 0x2e8, 0x3e8}; - int i; + static const resource_size_t base[] = {0x2f8, 0x3f8, 0x2e8, 0x3e8}; + unsigned int i; for (i = 0; i < ARRAY_SIZE(base); i++) { if (pnp_possible_config(dev, IORESOURCE_IO, base[i], 8)) - return 1; + return true; } - return 0; + return false; } /* @@ -425,8 +427,8 @@ static int check_resources(struct pnp_dev *dev) static int serial_pnp_guess_board(struct pnp_dev *dev) { if (!(check_name(pnp_dev_name(dev)) || - (dev->card && check_name(dev->card->name)))) - return -ENODEV; + (dev->card && check_name(dev->card->name)))) + return -ENODEV; if (check_resources(dev)) return 0; @@ -462,11 +464,11 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) } else return -ENODEV; -#ifdef SERIAL_DEBUG_PNP - printk(KERN_DEBUG - "Setup PNP port: port %x, mem 0x%lx, irq %d, type %d\n", - uart.port.iobase, uart.port.mapbase, uart.port.irq, uart.port.iotype); -#endif + dev_dbg(&dev->dev, + "Setup PNP port: port %lx, mem %pa, irq %d, type %d\n", + uart.port.iobase, &uart.port.mapbase, + uart.port.irq, uart.port.iotype); + if (flags & CIR_PORT) { uart.port.flags |= UPF_FIXED_PORT | UPF_FIXED_TYPE; uart.port.type = PORT_8250_CIR; diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c index 8d262bce97e4..e213da01a3d7 100644 --- a/drivers/tty/serial/8250/8250_port.c +++ b/drivers/tty/serial/8250/8250_port.c @@ -37,6 +37,7 @@ #include <linux/slab.h> #include <linux/uaccess.h> #include <linux/pm_runtime.h> +#include <linux/timer.h> #include <asm/io.h> #include <asm/irq.h> @@ -52,7 +53,7 @@ #define DEBUG_AUTOCONF(fmt...) do { } while (0) #endif -#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) +#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) /* * Here we define the default xmit fifo size used for each type of UART. @@ -250,9 +251,11 @@ static const struct serial8250_config uart_config[] = { .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, .flags = UART_CAP_FIFO | UART_CAP_AFE, }, -/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement -workaround of errata A-008006 which states that tx_loadsz should be -configured less than Maximum supported fifo bytes */ + /* + * tx_loadsz is set to 63-bytes instead of 64-bytes to implement + * workaround of errata A-008006 which states that tx_loadsz should + * be configured less than Maximum supported fifo bytes. + */ [PORT_16550A_FSL64] = { .name = "16550A_FSL64", .fifo_size = 64, @@ -522,6 +525,20 @@ static void serial8250_clear_fifos(struct uart_8250_port *p) } } +static inline void serial8250_em485_rts_after_send(struct uart_8250_port *p) +{ + unsigned char mcr = serial_in(p, UART_MCR); + + if (p->port.rs485.flags & SER_RS485_RTS_AFTER_SEND) + mcr |= UART_MCR_RTS; + else + mcr &= ~UART_MCR_RTS; + serial_out(p, UART_MCR, mcr); +} + +static void serial8250_em485_handle_start_tx(unsigned long arg); +static void serial8250_em485_handle_stop_tx(unsigned long arg); + void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p) { serial8250_clear_fifos(p); @@ -546,6 +563,73 @@ void serial8250_rpm_put(struct uart_8250_port *p) } EXPORT_SYMBOL_GPL(serial8250_rpm_put); +/** + * serial8250_em485_init() - put uart_8250_port into rs485 emulating + * @p: uart_8250_port port instance + * + * The function is used to start rs485 software emulating on the + * &struct uart_8250_port* @p. Namely, RTS is switched before/after + * transmission. The function is idempotent, so it is safe to call it + * multiple times. + * + * The caller MUST enable interrupt on empty shift register before + * calling serial8250_em485_init(). This interrupt is not a part of + * 8250 standard, but implementation defined. + * + * The function is supposed to be called from .rs485_config callback + * or from any other callback protected with p->port.lock spinlock. + * + * See also serial8250_em485_destroy() + * + * Return 0 - success, -errno - otherwise + */ +int serial8250_em485_init(struct uart_8250_port *p) +{ + if (p->em485 != NULL) + return 0; + + p->em485 = kmalloc(sizeof(struct uart_8250_em485), GFP_ATOMIC); + if (p->em485 == NULL) + return -ENOMEM; + + setup_timer(&p->em485->stop_tx_timer, + serial8250_em485_handle_stop_tx, (unsigned long)p); + setup_timer(&p->em485->start_tx_timer, + serial8250_em485_handle_start_tx, (unsigned long)p); + p->em485->active_timer = NULL; + + serial8250_em485_rts_after_send(p); + + return 0; +} +EXPORT_SYMBOL_GPL(serial8250_em485_init); + +/** + * serial8250_em485_destroy() - put uart_8250_port into normal state + * @p: uart_8250_port port instance + * + * The function is used to stop rs485 software emulating on the + * &struct uart_8250_port* @p. The function is idempotent, so it is safe to + * call it multiple times. + * + * The function is supposed to be called from .rs485_config callback + * or from any other callback protected with p->port.lock spinlock. + * + * See also serial8250_em485_init() + */ +void serial8250_em485_destroy(struct uart_8250_port *p) +{ + if (p->em485 == NULL) + return; + + del_timer(&p->em485->start_tx_timer); + del_timer(&p->em485->stop_tx_timer); + + kfree(p->em485); + p->em485 = NULL; +} +EXPORT_SYMBOL_GPL(serial8250_em485_destroy); + /* * These two wrappers ensure that enable_runtime_pm_tx() can be called more than * once and disable_runtime_pm_tx() will still disable RPM because the fifo is @@ -731,22 +815,16 @@ static int size_fifo(struct uart_8250_port *up) */ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) { - unsigned char old_dll, old_dlm, old_lcr; - unsigned int id; + unsigned char old_lcr; + unsigned int id, old_dl; old_lcr = serial_in(p, UART_LCR); serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A); + old_dl = serial_dl_read(p); + serial_dl_write(p, 0); + id = serial_dl_read(p); + serial_dl_write(p, old_dl); - old_dll = serial_in(p, UART_DLL); - old_dlm = serial_in(p, UART_DLM); - - serial_out(p, UART_DLL, 0); - serial_out(p, UART_DLM, 0); - - id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8; - - serial_out(p, UART_DLL, old_dll); - serial_out(p, UART_DLM, old_dlm); serial_out(p, UART_LCR, old_lcr); return id; @@ -1238,8 +1316,7 @@ static void autoconfig(struct uart_8250_port *up) out_lock: spin_unlock_irqrestore(&port->lock, flags); if (up->capabilities != old_capabilities) { - printk(KERN_WARNING - "ttyS%d: detected caps %08x should be %08x\n", + pr_warn("ttyS%d: detected caps %08x should be %08x\n", serial_index(port), old_capabilities, up->capabilities); } @@ -1304,7 +1381,69 @@ static void autoconfig_irq(struct uart_8250_port *up) port->irq = (irq > 0) ? irq : 0; } -static inline void __stop_tx(struct uart_8250_port *p) +static void serial8250_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + + up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); + up->port.read_status_mask &= ~UART_LSR_DR; + serial_port_out(port, UART_IER, up->ier); + + serial8250_rpm_put(up); +} + +static void __do_stop_tx_rs485(struct uart_8250_port *p) +{ + if (!p->em485) + return; + + serial8250_em485_rts_after_send(p); + /* + * Empty the RX FIFO, we are not interested in anything + * received during the half-duplex transmission. + */ + if (!(p->port.rs485.flags & SER_RS485_RX_DURING_TX)) + serial8250_clear_fifos(p); +} + +static void serial8250_em485_handle_stop_tx(unsigned long arg) +{ + struct uart_8250_port *p = (struct uart_8250_port *)arg; + struct uart_8250_em485 *em485 = p->em485; + unsigned long flags; + + spin_lock_irqsave(&p->port.lock, flags); + if (em485 && + em485->active_timer == &em485->stop_tx_timer) { + __do_stop_tx_rs485(p); + em485->active_timer = NULL; + } + spin_unlock_irqrestore(&p->port.lock, flags); +} + +static void __stop_tx_rs485(struct uart_8250_port *p) +{ + struct uart_8250_em485 *em485 = p->em485; + + if (!em485) + return; + + /* + * __do_stop_tx_rs485 is going to set RTS according to config + * AND flush RX FIFO if required. + */ + if (p->port.rs485.delay_rts_after_send > 0) { + em485->active_timer = &em485->stop_tx_timer; + mod_timer(&em485->stop_tx_timer, jiffies + + p->port.rs485.delay_rts_after_send * HZ / 1000); + } else { + __do_stop_tx_rs485(p); + } +} + +static inline void __do_stop_tx(struct uart_8250_port *p) { if (p->ier & UART_IER_THRI) { p->ier &= ~UART_IER_THRI; @@ -1313,6 +1452,28 @@ static inline void __stop_tx(struct uart_8250_port *p) } } +static inline void __stop_tx(struct uart_8250_port *p) +{ + struct uart_8250_em485 *em485 = p->em485; + + if (em485) { + unsigned char lsr = serial_in(p, UART_LSR); + /* + * To provide required timeing and allow FIFO transfer, + * __stop_tx_rs485 must be called only when both FIFO and + * shift register are empty. It is for device driver to enable + * interrupt on TEMT. + */ + if ((lsr & BOTH_EMPTY) != BOTH_EMPTY) + return; + + del_timer(&em485->start_tx_timer); + em485->active_timer = NULL; + } + __do_stop_tx(p); + __stop_tx_rs485(p); +} + static void serial8250_stop_tx(struct uart_port *port) { struct uart_8250_port *up = up_to_u8250p(port); @@ -1330,12 +1491,10 @@ static void serial8250_stop_tx(struct uart_port *port) serial8250_rpm_put(up); } -static void serial8250_start_tx(struct uart_port *port) +static inline void __start_tx(struct uart_port *port) { struct uart_8250_port *up = up_to_u8250p(port); - serial8250_rpm_get_tx(up); - if (up->dma && !up->dma->tx_dma(up)) return; @@ -1345,6 +1504,7 @@ static void serial8250_start_tx(struct uart_port *port) if (up->bugs & UART_BUG_TXEN) { unsigned char lsr; + lsr = serial_in(up, UART_LSR); up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; if (lsr & UART_LSR_THRE) @@ -1361,33 +1521,83 @@ static void serial8250_start_tx(struct uart_port *port) } } -static void serial8250_throttle(struct uart_port *port) +static inline void start_tx_rs485(struct uart_port *port) { - port->throttle(port); + struct uart_8250_port *up = up_to_u8250p(port); + struct uart_8250_em485 *em485 = up->em485; + unsigned char mcr; + + if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) + serial8250_stop_rx(&up->port); + + del_timer(&em485->stop_tx_timer); + em485->active_timer = NULL; + + mcr = serial_in(up, UART_MCR); + if (!!(up->port.rs485.flags & SER_RS485_RTS_ON_SEND) != + !!(mcr & UART_MCR_RTS)) { + if (up->port.rs485.flags & SER_RS485_RTS_ON_SEND) + mcr |= UART_MCR_RTS; + else + mcr &= ~UART_MCR_RTS; + serial_out(up, UART_MCR, mcr); + + if (up->port.rs485.delay_rts_before_send > 0) { + em485->active_timer = &em485->start_tx_timer; + mod_timer(&em485->start_tx_timer, jiffies + + up->port.rs485.delay_rts_before_send * HZ / 1000); + return; + } + } + + __start_tx(port); } -static void serial8250_unthrottle(struct uart_port *port) +static void serial8250_em485_handle_start_tx(unsigned long arg) { - port->unthrottle(port); + struct uart_8250_port *p = (struct uart_8250_port *)arg; + struct uart_8250_em485 *em485 = p->em485; + unsigned long flags; + + spin_lock_irqsave(&p->port.lock, flags); + if (em485 && + em485->active_timer == &em485->start_tx_timer) { + __start_tx(&p->port); + em485->active_timer = NULL; + } + spin_unlock_irqrestore(&p->port.lock, flags); } -static void serial8250_stop_rx(struct uart_port *port) +static void serial8250_start_tx(struct uart_port *port) { struct uart_8250_port *up = up_to_u8250p(port); + struct uart_8250_em485 *em485 = up->em485; - serial8250_rpm_get(up); + serial8250_rpm_get_tx(up); - up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); - up->port.read_status_mask &= ~UART_LSR_DR; - serial_port_out(port, UART_IER, up->ier); + if (em485 && + em485->active_timer == &em485->start_tx_timer) + return; - serial8250_rpm_put(up); + if (em485) + start_tx_rs485(port); + else + __start_tx(port); +} + +static void serial8250_throttle(struct uart_port *port) +{ + port->throttle(port); +} + +static void serial8250_unthrottle(struct uart_port *port) +{ + port->unthrottle(port); } static void serial8250_disable_ms(struct uart_port *port) { - struct uart_8250_port *up = - container_of(port, struct uart_8250_port, port); + struct uart_8250_port *up = up_to_u8250p(port); /* no MSR capabilities */ if (up->bugs & UART_BUG_NOMSR) @@ -1412,81 +1622,85 @@ static void serial8250_enable_ms(struct uart_port *port) serial8250_rpm_put(up); } +static void serial8250_read_char(struct uart_8250_port *up, unsigned char lsr) +{ + struct uart_port *port = &up->port; + unsigned char ch; + char flag = TTY_NORMAL; + + if (likely(lsr & UART_LSR_DR)) + ch = serial_in(up, UART_RX); + else + /* + * Intel 82571 has a Serial Over Lan device that will + * set UART_LSR_BI without setting UART_LSR_DR when + * it receives a break. To avoid reading from the + * receive buffer without UART_LSR_DR bit set, we + * just force the read character to be 0 + */ + ch = 0; + + port->icount.rx++; + + lsr |= up->lsr_saved_flags; + up->lsr_saved_flags = 0; + + if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) { + if (lsr & UART_LSR_BI) { + lsr &= ~(UART_LSR_FE | UART_LSR_PE); + port->icount.brk++; + /* + * We do the SysRQ and SAK checking + * here because otherwise the break + * may get masked by ignore_status_mask + * or read_status_mask. + */ + if (uart_handle_break(port)) + return; + } else if (lsr & UART_LSR_PE) + port->icount.parity++; + else if (lsr & UART_LSR_FE) + port->icount.frame++; + if (lsr & UART_LSR_OE) + port->icount.overrun++; + + /* + * Mask off conditions which should be ignored. + */ + lsr &= port->read_status_mask; + + if (lsr & UART_LSR_BI) { + DEBUG_INTR("handling break...."); + flag = TTY_BREAK; + } else if (lsr & UART_LSR_PE) + flag = TTY_PARITY; + else if (lsr & UART_LSR_FE) + flag = TTY_FRAME; + } + if (uart_handle_sysrq_char(port, ch)) + return; + + uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); +} + /* * serial8250_rx_chars: processes according to the passed in LSR * value, and returns the remaining LSR bits not handled * by this Rx routine. */ -unsigned char -serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr) +unsigned char serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr) { struct uart_port *port = &up->port; - unsigned char ch; int max_count = 256; - char flag; do { - if (likely(lsr & UART_LSR_DR)) - ch = serial_in(up, UART_RX); - else - /* - * Intel 82571 has a Serial Over Lan device that will - * set UART_LSR_BI without setting UART_LSR_DR when - * it receives a break. To avoid reading from the - * receive buffer without UART_LSR_DR bit set, we - * just force the read character to be 0 - */ - ch = 0; - - flag = TTY_NORMAL; - port->icount.rx++; - - lsr |= up->lsr_saved_flags; - up->lsr_saved_flags = 0; - - if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) { - if (lsr & UART_LSR_BI) { - lsr &= ~(UART_LSR_FE | UART_LSR_PE); - port->icount.brk++; - /* - * We do the SysRQ and SAK checking - * here because otherwise the break - * may get masked by ignore_status_mask - * or read_status_mask. - */ - if (uart_handle_break(port)) - goto ignore_char; - } else if (lsr & UART_LSR_PE) - port->icount.parity++; - else if (lsr & UART_LSR_FE) - port->icount.frame++; - if (lsr & UART_LSR_OE) - port->icount.overrun++; - - /* - * Mask off conditions which should be ignored. - */ - lsr &= port->read_status_mask; - - if (lsr & UART_LSR_BI) { - DEBUG_INTR("handling break...."); - flag = TTY_BREAK; - } else if (lsr & UART_LSR_PE) - flag = TTY_PARITY; - else if (lsr & UART_LSR_FE) - flag = TTY_FRAME; - } - if (uart_handle_sysrq_char(port, ch)) - goto ignore_char; - - uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); - -ignore_char: + serial8250_read_char(up, lsr); + if (--max_count == 0) + break; lsr = serial_in(up, UART_LSR); - } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0)); - spin_unlock(&port->lock); + } while (lsr & (UART_LSR_DR | UART_LSR_BI)); + tty_flip_buffer_push(&port->state->port); - spin_lock(&port->lock); return lsr; } EXPORT_SYMBOL_GPL(serial8250_rx_chars); @@ -1519,11 +1733,9 @@ void serial8250_tx_chars(struct uart_8250_port *up) port->icount.tx++; if (uart_circ_empty(xmit)) break; - if (up->capabilities & UART_CAP_HFIFO) { - if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) != - BOTH_EMPTY) - break; - } + if ((up->capabilities & UART_CAP_HFIFO) && + (serial_in(up, UART_LSR) & BOTH_EMPTY) != BOTH_EMPTY) + break; } while (--count > 0); if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) @@ -1752,6 +1964,7 @@ static void wait_for_xmitr(struct uart_8250_port *up, int bits) /* Wait up to 1s for flow control if necessary */ if (up->port.flags & UPF_CONS_FLOW) { unsigned int tmout; + for (tmout = 1000000; tmout; tmout--) { unsigned int msr = serial_in(up, UART_MSR); up->msr_saved_flags |= msr & MSR_SAVE_FLAGS; @@ -1985,23 +2198,23 @@ int serial8250_do_startup(struct uart_port *port) serial8250_set_mctrl(port, port->mctrl); - /* Serial over Lan (SoL) hack: - Intel 8257x Gigabit ethernet chips have a - 16550 emulation, to be used for Serial Over Lan. - Those chips take a longer time than a normal - serial device to signalize that a transmission - data was queued. Due to that, the above test generally - fails. One solution would be to delay the reading of - iir. However, this is not reliable, since the timeout - is variable. So, let's just don't test if we receive - TX irq. This way, we'll never enable UART_BUG_TXEN. + /* + * Serial over Lan (SoL) hack: + * Intel 8257x Gigabit ethernet chips have a 16550 emulation, to be + * used for Serial Over Lan. Those chips take a longer time than a + * normal serial device to signalize that a transmission data was + * queued. Due to that, the above test generally fails. One solution + * would be to delay the reading of iir. However, this is not + * reliable, since the timeout is variable. So, let's just don't + * test if we receive TX irq. This way, we'll never enable + * UART_BUG_TXEN. */ if (up->port.flags & UPF_NO_TXEN_TEST) goto dont_test_tx_en; /* - * Do a quick test to see if we receive an - * interrupt when we enable the TX irq. + * Do a quick test to see if we receive an interrupt when we enable + * the TX irq. */ serial_port_out(port, UART_IER, UART_IER_THRI); lsr = serial_port_in(port, UART_LSR); @@ -2084,8 +2297,12 @@ void serial8250_do_shutdown(struct uart_port *port) /* * Disable interrupts from this port */ + spin_lock_irqsave(&port->lock, flags); up->ier = 0; serial_port_out(port, UART_IER, 0); + spin_unlock_irqrestore(&port->lock, flags); + + synchronize_irq(port->irq); if (up->dma) serial8250_release_dma(up); @@ -2251,9 +2468,9 @@ static void serial8250_set_divisor(struct uart_port *port, unsigned int baud, serial_port_out(port, 0x2, quot_frac); } -static unsigned int -serial8250_get_baud_rate(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) +static unsigned int serial8250_get_baud_rate(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) { unsigned int tolerance = port->uartclk / 100; @@ -2270,7 +2487,7 @@ serial8250_get_baud_rate(struct uart_port *port, struct ktermios *termios, void serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) + struct ktermios *old) { struct uart_8250_port *up = up_to_u8250p(port); unsigned char cval; @@ -2583,8 +2800,7 @@ static int do_get_rxtrig(struct tty_port *port) { struct uart_state *state = container_of(port, struct uart_state, port); struct uart_port *uport = state->uart_port; - struct uart_8250_port *up = - container_of(uport, struct uart_8250_port, port); + struct uart_8250_port *up = up_to_u8250p(uport); if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1) return -EINVAL; @@ -2620,8 +2836,7 @@ static int do_set_rxtrig(struct tty_port *port, unsigned char bytes) { struct uart_state *state = container_of(port, struct uart_state, port); struct uart_port *uport = state->uart_port; - struct uart_8250_port *up = - container_of(uport, struct uart_8250_port, port); + struct uart_8250_port *up = up_to_u8250p(uport); int rxtrig; if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 || @@ -2745,8 +2960,7 @@ serial8250_verify_port(struct uart_port *port, struct serial_struct *ser) return 0; } -static const char * -serial8250_type(struct uart_port *port) +static const char *serial8250_type(struct uart_port *port) { int type = port->type; diff --git a/drivers/tty/serial/8250/8250_uniphier.c b/drivers/tty/serial/8250/8250_uniphier.c index bab6b3ae2540..1b7bd26555b7 100644 --- a/drivers/tty/serial/8250/8250_uniphier.c +++ b/drivers/tty/serial/8250/8250_uniphier.c @@ -35,7 +35,7 @@ struct uniphier8250_priv { spinlock_t atomic_write_lock; }; -#ifdef CONFIG_SERIAL_8250_CONSOLE +#if defined(CONFIG_SERIAL_8250_CONSOLE) && !defined(MODULE) static int __init uniphier_early_console_setup(struct earlycon_device *device, const char *options) { diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index b03cb5175113..64742a086ae3 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -262,7 +262,12 @@ config SERIAL_8250_RSA bool "Support RSA serial ports" depends on SERIAL_8250_EXTENDED help - ::: To be written ::: + Say Y here if you have a IODATA RSA-DV II/S ISA card and + would like to use its >115kbps speeds. + You will need to provide module parameter "probe_rsa", or boot-time + parameter 8250.probe_rsa with I/O addresses of this card then. + + If you don't have such card, or if unsure, say N. config SERIAL_8250_ACORN tristate "Acorn expansion card serial port support" @@ -272,6 +277,30 @@ config SERIAL_8250_ACORN system, say Y to this option. The driver can handle 1, 2, or 3 port cards. If unsure, say N. +config SERIAL_8250_BCM2835AUX + tristate "BCM2835 auxiliar mini UART support" + depends on ARCH_BCM2835 || COMPILE_TEST + depends on SERIAL_8250 && SERIAL_8250_SHARE_IRQ + help + Support for the BCM2835 auxiliar mini UART. + + Features and limitations of the UART are + Registers are similar to 16650 registers, + set bits in the control registers that are unsupported + are ignored and read back as 0 + 7/8 bit operation with 1 start and 1 stop bit + 8 symbols deep fifo for rx and tx + SW controlled RTS and SW readable CTS + Clock rate derived from system clock + Uses 8 times oversampling (compared to 16 times for 16650) + Missing break detection (but break generation) + Missing framing error detection + Missing parity bit + Missing receive time-out interrupt + Missing DCD, DSR, DTR and RI signals + + If unsure, say N. + config SERIAL_8250_FSL bool depends on SERIAL_8250_CONSOLE @@ -295,6 +324,7 @@ config SERIAL_8250_EM config SERIAL_8250_RT288X bool "Ralink RT288x/RT305x/RT3662/RT3883 serial port support" depends on SERIAL_8250 + depends on MIPS || COMPILE_TEST default y if MIPS_ALCHEMY || SOC_RT288X || SOC_RT305X || SOC_RT3883 || SOC_MT7620 help Selecting this option will add support for the alternate register @@ -346,7 +376,7 @@ config SERIAL_8250_LPC18XX serial port, say Y to this option. If unsure, say Y. config SERIAL_8250_MT6577 - bool "Mediatek serial port support" + tristate "Mediatek serial port support" depends on SERIAL_8250 && ARCH_MEDIATEK help If you have a Mediatek based board and want to use the @@ -360,9 +390,10 @@ config SERIAL_8250_UNIPHIER serial ports, say Y to this option. If unsure, say N. config SERIAL_8250_INGENIC - bool "Support for Ingenic SoC serial ports" - depends on OF_FLATTREE - select LIBFDT + tristate "Support for Ingenic SoC serial ports" + depends on SERIAL_8250 + depends on (OF_FLATTREE && SERIAL_8250_CONSOLE) || !SERIAL_EARLYCON + depends on MIPS || COMPILE_TEST help If you have a system using an Ingenic SoC and wish to make use of its UARTs, say Y to this option. If unsure, say N. @@ -378,6 +409,16 @@ config SERIAL_8250_MID present on the UART found on Intel Medfield SOC and various other Intel platforms. +config SERIAL_8250_MOXA + tristate "MOXA SmartIO MUE support" + depends on SERIAL_8250 && PCI + help + Say Y here if you have a Moxa SmartIO MUE multiport serial card. + If unsure, say N. + + This driver can also be built as a module. The module will be called + 8250_moxa. If you want to do that, say M here. + config SERIAL_OF_PLATFORM tristate "Devicetree based probing for 8250 ports" depends on SERIAL_8250 && OF diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile index b9b9bca5b6c3..c9a2d6ed87e9 100644 --- a/drivers/tty/serial/8250/Makefile +++ b/drivers/tty/serial/8250/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o obj-$(CONFIG_SERIAL_8250_CS) += serial_cs.o obj-$(CONFIG_SERIAL_8250_ACORN) += 8250_acorn.o +obj-$(CONFIG_SERIAL_8250_BCM2835AUX) += 8250_bcm2835aux.o obj-$(CONFIG_SERIAL_8250_CONSOLE) += 8250_early.o obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o @@ -28,6 +29,7 @@ obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o +obj-$(CONFIG_SERIAL_8250_MOXA) += 8250_moxa.o obj-$(CONFIG_SERIAL_OF_PLATFORM) += 8250_of.o CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c index 4d180c9423ef..933c2688dd7e 100644 --- a/drivers/tty/serial/8250/serial_cs.c +++ b/drivers/tty/serial/8250/serial_cs.c @@ -28,7 +28,7 @@ and other provisions required by the GPL. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the GPL. - + ======================================================================*/ #include <linux/module.h> @@ -257,7 +257,7 @@ static const struct serial_quirk quirks[] = { }; -static int serial_config(struct pcmcia_device * link); +static int serial_config(struct pcmcia_device *link); static void serial_remove(struct pcmcia_device *link) @@ -309,7 +309,7 @@ static int serial_probe(struct pcmcia_device *link) dev_dbg(&link->dev, "serial_attach()\n"); /* Create new serial device */ - info = kzalloc(sizeof (*info), GFP_KERNEL); + info = kzalloc(sizeof(*info), GFP_KERNEL); if (!info) return -ENOMEM; info->p_dev = link; @@ -339,7 +339,7 @@ static void serial_detach(struct pcmcia_device *link) /*====================================================================*/ -static int setup_serial(struct pcmcia_device *handle, struct serial_info * info, +static int setup_serial(struct pcmcia_device *handle, struct serial_info *info, unsigned int iobase, int irq) { struct uart_8250_port uart; @@ -441,16 +441,20 @@ static int simple_config(struct pcmcia_device *link) struct serial_info *info = link->priv; int i = -ENODEV, try; - /* First pass: look for a config entry that looks normal. - * Two tries: without IO aliases, then with aliases */ + /* + * First pass: look for a config entry that looks normal. + * Two tries: without IO aliases, then with aliases. + */ link->config_flags |= CONF_AUTO_SET_VPP; for (try = 0; try < 4; try++) if (!pcmcia_loop_config(link, simple_config_check, &try)) goto found_port; - /* Second pass: try to find an entry that isn't picky about - its base address, then try to grab any standard serial port - address, and finally try to get any free port. */ + /* + * Second pass: try to find an entry that isn't picky about + * its base address, then try to grab any standard serial port + * address, and finally try to get any free port. + */ if (!pcmcia_loop_config(link, simple_config_check_notpicky, NULL)) goto found_port; @@ -480,8 +484,10 @@ static int multi_config_check(struct pcmcia_device *p_dev, void *priv_data) if (p_dev->resource[1]->end) return -EINVAL; - /* The quad port cards have bad CIS's, so just look for a - window larger than 8 ports and assume it will be right */ + /* + * The quad port cards have bad CIS's, so just look for a + * window larger than 8 ports and assume it will be right. + */ if (p_dev->resource[0]->end <= 8) return -EINVAL; @@ -527,8 +533,8 @@ static int multi_config(struct pcmcia_device *link) info->multi = 2; if (pcmcia_loop_config(link, multi_config_check_notpicky, &base2)) { - dev_warn(&link->dev, "no usable port range " - "found, giving up\n"); + dev_warn(&link->dev, + "no usable port range found, giving up\n"); return -ENODEV; } } @@ -600,7 +606,7 @@ static int serial_check_for_multi(struct pcmcia_device *p_dev, void *priv_data) } -static int serial_config(struct pcmcia_device * link) +static int serial_config(struct pcmcia_device *link) { struct serial_info *info = link->priv; int i; @@ -623,8 +629,10 @@ static int serial_config(struct pcmcia_device * link) break; } - /* Another check for dual-serial cards: look for either serial or - multifunction cards that ask for appropriate IO port ranges */ + /* + * Another check for dual-serial cards: look for either serial or + * multifunction cards that ask for appropriate IO port ranges. + */ if ((info->multi == 0) && (link->has_func_id) && (link->socket->pcmcia_pfc == 0) && @@ -701,7 +709,7 @@ static const struct pcmcia_device_id serial_ids[] = { PCMCIA_PFC_DEVICE_PROD_ID12(1, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58), PCMCIA_PFC_DEVICE_PROD_ID12(1, "MEGAHERTZ", "XJEM1144/CCEM1144", 0xf510db04, 0x52d21e1e), PCMCIA_PFC_DEVICE_PROD_ID12(1, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555), - PCMCIA_PFC_DEVICE_PROD_ID12(1, "NEC", "PK-UG-J001" ,0x18df0ba0 ,0x831b1064), + PCMCIA_PFC_DEVICE_PROD_ID12(1, "NEC", "PK-UG-J001", 0x18df0ba0, 0x831b1064), PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Diamonds Modem+Ethernet", 0xc2f80cd, 0x656947b9), PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Hearts Modem+Ethernet", 0xc2f80cd, 0xdc9ba5ed), PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc), @@ -797,30 +805,30 @@ static const struct pcmcia_device_id serial_ids[] = { PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "cis/COMpad2.cis"), PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "cis/RS-COM-2P.cis"), PCMCIA_DEVICE_CIS_MANF_CARD(0x0013, 0x0000, "cis/GLOBETROTTER.cis"), - PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL100 1.00.",0x19ca78af,0xf964f42b), - PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL100",0x19ca78af,0x71d98e83), - PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL232 1.00.",0x19ca78af,0x69fb7490), - PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL232",0x19ca78af,0xb6bc0235), - PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.","SERIAL CARD: CF232",0x63f2e0bd,0xb9e175d3), - PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.","SERIAL CARD: CF232-5",0x63f2e0bd,0xfce33442), - PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF232",0x3beb8cf2,0x171e7190), - PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF232-5",0x3beb8cf2,0x20da4262), - PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF428",0x3beb8cf2,0xea5dd57d), - PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF500",0x3beb8cf2,0xd77255fa), - PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: IC232",0x3beb8cf2,0x6a709903), - PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: SL232",0x3beb8cf2,0x18430676), - PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: XL232",0x3beb8cf2,0x6f933767), - PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: CF332",0x3beb8cf2,0x16dc1ba7), - PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL332",0x3beb8cf2,0x19816c41), - PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL385",0x3beb8cf2,0x64112029), - PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), - PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial+Parallel Port: SP230",0x3beb8cf2,0xdb9e58bc), - PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: CF332",0x3beb8cf2,0x16dc1ba7), - PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL332",0x3beb8cf2,0x19816c41), - PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL385",0x3beb8cf2,0x64112029), - PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), - PCMCIA_MFC_DEVICE_PROD_ID12(2,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), - PCMCIA_MFC_DEVICE_PROD_ID12(3,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), + PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100 1.00.", 0x19ca78af, 0xf964f42b), + PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100", 0x19ca78af, 0x71d98e83), + PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232 1.00.", 0x19ca78af, 0x69fb7490), + PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232", 0x19ca78af, 0xb6bc0235), + PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232", 0x63f2e0bd, 0xb9e175d3), + PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232-5", 0x63f2e0bd, 0xfce33442), + PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232", 0x3beb8cf2, 0x171e7190), + PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232-5", 0x3beb8cf2, 0x20da4262), + PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF428", 0x3beb8cf2, 0xea5dd57d), + PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF500", 0x3beb8cf2, 0xd77255fa), + PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: IC232", 0x3beb8cf2, 0x6a709903), + PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: SL232", 0x3beb8cf2, 0x18430676), + PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: XL232", 0x3beb8cf2, 0x6f933767), + PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7), + PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41), + PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029), + PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4), + PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial+Parallel Port: SP230", 0x3beb8cf2, 0xdb9e58bc), + PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7), + PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41), + PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029), + PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4), + PCMCIA_MFC_DEVICE_PROD_ID12(2, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4), + PCMCIA_MFC_DEVICE_PROD_ID12(3, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4), PCMCIA_DEVICE_MANF_CARD(0x0279, 0x950b), /* too generic */ /* PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0160, 0x0002), */ diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 39721ec4f415..13d4ed6caac4 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -610,6 +610,7 @@ config SERIAL_UARTLITE_CONSOLE bool "Support for console on Xilinx uartlite serial port" depends on SERIAL_UARTLITE=y select SERIAL_CORE_CONSOLE + select SERIAL_EARLYCON help Say Y here if you wish to use a Xilinx uartlite as the system console (the system console is the device which receives all kernel @@ -732,7 +733,7 @@ config SERIAL_IP22_ZILOG_CONSOLE config SERIAL_SH_SCI tristate "SuperH SCI(F) serial port support" - depends on SUPERH || ARCH_SHMOBILE || H8300 || COMPILE_TEST + depends on SUPERH || ARCH_RENESAS || H8300 || COMPILE_TEST select SERIAL_CORE config SERIAL_SH_SCI_NR_UARTS @@ -745,6 +746,12 @@ config SERIAL_SH_SCI_CONSOLE depends on SERIAL_SH_SCI=y select SERIAL_CORE_CONSOLE +config SERIAL_SH_SCI_EARLYCON + bool "Support for early console on SuperH SCI(F)" + depends on SERIAL_SH_SCI=y + select SERIAL_CORE_CONSOLE + select SERIAL_EARLYCON + config SERIAL_SH_SCI_DMA bool "DMA support" depends on SERIAL_SH_SCI && DMA_ENGINE @@ -793,17 +800,6 @@ config SERIAL_CORE_CONSOLE config CONSOLE_POLL bool -config SERIAL_68328 - bool "68328 serial support" - depends on M68328 || M68EZ328 || M68VZ328 - help - This driver supports the built-in serial port of the Motorola 68328 - (standard, EZ and VZ varieties). - -config SERIAL_68328_RTS_CTS - bool "Support RTS/CTS on 68328 serial port" - depends on SERIAL_68328 - config SERIAL_MCF bool "Coldfire serial support" depends on COLDFIRE @@ -1606,6 +1602,28 @@ config SERIAL_STM32_CONSOLE depends on SERIAL_STM32=y select SERIAL_CORE_CONSOLE +config SERIAL_MVEBU_UART + bool "Marvell EBU serial port support" + select SERIAL_CORE + help + This driver is for Marvell EBU SoC's UART. If you have a machine + based on the Armada-3700 SoC and wish to use the on-board serial + port, + say 'Y' here. + Otherwise, say 'N'. + +config SERIAL_MVEBU_CONSOLE + bool "Console on Marvell EBU serial port" + depends on SERIAL_MVEBU_UART + select SERIAL_CORE_CONSOLE + select SERIAL_EARLYCON + default y + help + Say 'Y' here if you wish to use Armada-3700 UART as the system console. + (the system console is the device which receives all kernel messages + and warnings and which allows logins in single user mode) + Otherwise, say 'N'. + endmenu config SERIAL_MCTRL_GPIO diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index b391c9b31960..8c261adac04e 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -34,7 +34,6 @@ obj-$(CONFIG_SERIAL_MAX3100) += max3100.o obj-$(CONFIG_SERIAL_MAX310X) += max310x.o obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o obj-$(CONFIG_SERIAL_MUX) += mux.o -obj-$(CONFIG_SERIAL_68328) += 68328serial.o obj-$(CONFIG_SERIAL_MCF) += mcf.o obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o obj-$(CONFIG_SERIAL_HS_LPC32XX) += lpc32xx_hs.o @@ -91,6 +90,7 @@ obj-$(CONFIG_SERIAL_CONEXANT_DIGICOLOR) += digicolor-usart.o obj-$(CONFIG_SERIAL_MEN_Z135) += men_z135_uart.o obj-$(CONFIG_SERIAL_SPRD) += sprd_serial.o obj-$(CONFIG_SERIAL_STM32) += stm32-usart.o +obj-$(CONFIG_SERIAL_MVEBU_UART) += mvebu-uart.o # GPIOLIB helpers for modem control lines obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index c0da0ccbbcf5..7c198e0a3178 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -187,7 +187,7 @@ static const u16 pl011_zte_offsets[REG_ARRAY_SIZE] = { [REG_DMACR] = ZX_UART011_DMACR, }; -static struct vendor_data vendor_zte = { +static struct vendor_data vendor_zte __maybe_unused = { .reg_offset = pl011_zte_offsets, .access_32b = true, .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8, @@ -420,7 +420,7 @@ static void pl011_dma_probe(struct uart_amba_port *uap) /* Optionally make use of an RX channel as well */ chan = dma_request_slave_channel(dev, "rx"); - if (!chan && plat->dma_rx_param) { + if (!chan && plat && plat->dma_rx_param) { chan = dma_request_channel(mask, plat->dma_filter, plat->dma_rx_param); if (!chan) { @@ -1167,7 +1167,7 @@ static void pl011_dma_shutdown(struct uart_amba_port *uap) /* Disable RX and TX DMA */ while (pl011_read(uap, REG_FR) & UART01x_FR_BUSY) - barrier(); + cpu_relax(); spin_lock_irq(&uap->port.lock); uap->dmacr &= ~(UART011_DMAONERR | UART011_RXDMAE | UART011_TXDMAE); @@ -1611,7 +1611,7 @@ static void pl011_put_poll_char(struct uart_port *port, container_of(port, struct uart_amba_port, port); while (pl011_read(uap, REG_FR) & UART01x_FR_TXFF) - barrier(); + cpu_relax(); pl011_write(ch, uap, REG_DR); } @@ -1947,6 +1947,8 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios, lcr_h |= UART01x_LCRH_PEN; if (!(termios->c_cflag & PARODD)) lcr_h |= UART01x_LCRH_EPS; + if (termios->c_cflag & CMSPAR) + lcr_h |= UART011_LCRH_SPS; } if (uap->fifosize > 1) lcr_h |= UART01x_LCRH_FEN; @@ -2150,7 +2152,7 @@ static void pl011_console_putchar(struct uart_port *port, int ch) container_of(port, struct uart_amba_port, port); while (pl011_read(uap, REG_FR) & UART01x_FR_TXFF) - barrier(); + cpu_relax(); pl011_write(ch, uap, REG_DR); } @@ -2158,7 +2160,7 @@ static void pl011_console_write(struct console *co, const char *s, unsigned int count) { struct uart_amba_port *uap = amba_ports[co->index]; - unsigned int status, old_cr = 0, new_cr; + unsigned int old_cr = 0, new_cr; unsigned long flags; int locked = 1; @@ -2188,9 +2190,8 @@ pl011_console_write(struct console *co, const char *s, unsigned int count) * Finally, wait for transmitter to become empty * and restore the TCR */ - do { - status = pl011_read(uap, REG_FR); - } while (status & UART01x_FR_BUSY); + while (pl011_read(uap, REG_FR) & UART01x_FR_BUSY) + cpu_relax(); if (!uap->vendor->always_enabled) pl011_write(old_cr, uap, REG_CR); @@ -2302,13 +2303,13 @@ static struct console amba_console = { static void pl011_putc(struct uart_port *port, int c) { while (readl(port->membase + UART01x_FR) & UART01x_FR_TXFF) - ; + cpu_relax(); if (port->iotype == UPIO_MEM32) writel(c, port->membase + UART01x_DR); else writeb(c, port->membase + UART01x_DR); while (readl(port->membase + UART01x_FR) & UART01x_FR_BUSY) - ; + cpu_relax(); } static void pl011_early_write(struct console *con, const char *s, unsigned n) @@ -2327,7 +2328,6 @@ static int __init pl011_early_console_setup(struct earlycon_device *device, device->con->write = pl011_early_write; return 0; } -EARLYCON_DECLARE(pl011, pl011_early_console_setup); OF_EARLYCON_DECLARE(pl011, "arm,pl011", pl011_early_console_setup); #else diff --git a/drivers/tty/serial/arc_uart.c b/drivers/tty/serial/arc_uart.c index 03ebe401fff7..3a1de5c87cb4 100644 --- a/drivers/tty/serial/arc_uart.c +++ b/drivers/tty/serial/arc_uart.c @@ -576,7 +576,6 @@ static int __init arc_early_console_setup(struct earlycon_device *dev, dev->con->write = arc_early_serial_write; return 0; } -EARLYCON_DECLARE(arc_uart, arc_early_console_setup); OF_EARLYCON_DECLARE(arc_uart, "snps,arc-uart", arc_early_console_setup); #endif /* CONFIG_SERIAL_ARC_CONSOLE */ diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 1c0884d8ef32..d9439e6ab719 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -159,8 +159,9 @@ struct atmel_uart_port { u32 rts_high; u32 rts_low; bool ms_irq_enabled; - bool is_usart; /* usart or uart */ - struct timer_list uart_timer; /* uart timer */ + u32 rtor; /* address of receiver timeout register if it exists */ + bool has_hw_timer; + struct timer_list uart_timer; bool suspended; unsigned int pending; @@ -1710,19 +1711,24 @@ static void atmel_get_ip_name(struct uart_port *port) struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); int name = atmel_uart_readl(port, ATMEL_US_NAME); u32 version; - int usart, uart; - /* usart and uart ascii */ - usart = 0x55534152; - uart = 0x44424755; - - atmel_port->is_usart = false; - - if (name == usart) { - dev_dbg(port->dev, "This is usart\n"); - atmel_port->is_usart = true; - } else if (name == uart) { - dev_dbg(port->dev, "This is uart\n"); - atmel_port->is_usart = false; + u32 usart, dbgu_uart, new_uart; + /* ASCII decoding for IP version */ + usart = 0x55534152; /* USAR(T) */ + dbgu_uart = 0x44424755; /* DBGU */ + new_uart = 0x55415254; /* UART */ + + atmel_port->has_hw_timer = false; + + if (name == new_uart) { + dev_dbg(port->dev, "Uart with hw timer"); + atmel_port->has_hw_timer = true; + atmel_port->rtor = ATMEL_UA_RTOR; + } else if (name == usart) { + dev_dbg(port->dev, "Usart\n"); + atmel_port->has_hw_timer = true; + atmel_port->rtor = ATMEL_US_RTOR; + } else if (name == dbgu_uart) { + dev_dbg(port->dev, "Dbgu or uart without hw timer\n"); } else { /* fallback for older SoCs: use version field */ version = atmel_uart_readl(port, ATMEL_US_VERSION); @@ -1730,12 +1736,12 @@ static void atmel_get_ip_name(struct uart_port *port) case 0x302: case 0x10213: dev_dbg(port->dev, "This version is usart\n"); - atmel_port->is_usart = true; + atmel_port->has_hw_timer = true; + atmel_port->rtor = ATMEL_US_RTOR; break; case 0x203: case 0x10202: dev_dbg(port->dev, "This version is uart\n"); - atmel_port->is_usart = false; break; default: dev_err(port->dev, "Not supported ip name nor version, set to uart\n"); @@ -1835,12 +1841,13 @@ static int atmel_startup(struct uart_port *port) if (atmel_use_pdc_rx(port)) { /* set UART timeout */ - if (!atmel_port->is_usart) { + if (!atmel_port->has_hw_timer) { mod_timer(&atmel_port->uart_timer, jiffies + uart_poll_timeout(port)); /* set USART timeout */ } else { - atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT); + atmel_uart_writel(port, atmel_port->rtor, + PDC_RX_TIMEOUT); atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); atmel_uart_writel(port, ATMEL_US_IER, @@ -1850,12 +1857,13 @@ static int atmel_startup(struct uart_port *port) atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); } else if (atmel_use_dma_rx(port)) { /* set UART timeout */ - if (!atmel_port->is_usart) { + if (!atmel_port->has_hw_timer) { mod_timer(&atmel_port->uart_timer, jiffies + uart_poll_timeout(port)); /* set USART timeout */ } else { - atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT); + atmel_uart_writel(port, atmel_port->rtor, + PDC_RX_TIMEOUT); atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); atmel_uart_writel(port, ATMEL_US_IER, @@ -2478,13 +2486,13 @@ static int __init atmel_console_init(void) struct atmel_uart_data *pdata = dev_get_platdata(&atmel_default_console_device->dev); int id = pdata->num; - struct atmel_uart_port *port = &atmel_ports[id]; + struct atmel_uart_port *atmel_port = &atmel_ports[id]; - port->backup_imr = 0; - port->uart.line = id; + atmel_port->backup_imr = 0; + atmel_port->uart.line = id; add_preferred_console(ATMEL_DEVICENAME, id, NULL); - ret = atmel_init_port(port, atmel_default_console_device); + ret = atmel_init_port(atmel_port, atmel_default_console_device); if (ret) return ret; register_console(&atmel_console); @@ -2599,23 +2607,23 @@ static int atmel_serial_resume(struct platform_device *pdev) #define atmel_serial_resume NULL #endif -static void atmel_serial_probe_fifos(struct atmel_uart_port *port, +static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port, struct platform_device *pdev) { - port->fifo_size = 0; - port->rts_low = 0; - port->rts_high = 0; + atmel_port->fifo_size = 0; + atmel_port->rts_low = 0; + atmel_port->rts_high = 0; if (of_property_read_u32(pdev->dev.of_node, "atmel,fifo-size", - &port->fifo_size)) + &atmel_port->fifo_size)) return; - if (!port->fifo_size) + if (!atmel_port->fifo_size) return; - if (port->fifo_size < ATMEL_MIN_FIFO_SIZE) { - port->fifo_size = 0; + if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) { + atmel_port->fifo_size = 0; dev_err(&pdev->dev, "Invalid FIFO size\n"); return; } @@ -2628,22 +2636,22 @@ static void atmel_serial_probe_fifos(struct atmel_uart_port *port, * Threshold to a reasonably high value respecting this 16 data * empirical rule when possible. */ - port->rts_high = max_t(int, port->fifo_size >> 1, - port->fifo_size - ATMEL_RTS_HIGH_OFFSET); - port->rts_low = max_t(int, port->fifo_size >> 2, - port->fifo_size - ATMEL_RTS_LOW_OFFSET); + atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1, + atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET); + atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2, + atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET); dev_info(&pdev->dev, "Using FIFO (%u data)\n", - port->fifo_size); + atmel_port->fifo_size); dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n", - port->rts_high); + atmel_port->rts_high); dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n", - port->rts_low); + atmel_port->rts_low); } static int atmel_serial_probe(struct platform_device *pdev) { - struct atmel_uart_port *port; + struct atmel_uart_port *atmel_port; struct device_node *np = pdev->dev.of_node; struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev); void *data; @@ -2674,99 +2682,133 @@ static int atmel_serial_probe(struct platform_device *pdev) goto err; } - port = &atmel_ports[ret]; - port->backup_imr = 0; - port->uart.line = ret; - atmel_serial_probe_fifos(port, pdev); + atmel_port = &atmel_ports[ret]; + atmel_port->backup_imr = 0; + atmel_port->uart.line = ret; + atmel_serial_probe_fifos(atmel_port, pdev); - spin_lock_init(&port->lock_suspended); + spin_lock_init(&atmel_port->lock_suspended); - ret = atmel_init_port(port, pdev); + ret = atmel_init_port(atmel_port, pdev); if (ret) goto err_clear_bit; - port->gpios = mctrl_gpio_init(&port->uart, 0); - if (IS_ERR(port->gpios)) { - ret = PTR_ERR(port->gpios); + atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0); + if (IS_ERR(atmel_port->gpios)) { + ret = PTR_ERR(atmel_port->gpios); goto err_clear_bit; } - if (!atmel_use_pdc_rx(&port->uart)) { + if (!atmel_use_pdc_rx(&atmel_port->uart)) { ret = -ENOMEM; data = kmalloc(sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE, GFP_KERNEL); if (!data) goto err_alloc_ring; - port->rx_ring.buf = data; + atmel_port->rx_ring.buf = data; } - rs485_enabled = port->uart.rs485.flags & SER_RS485_ENABLED; + rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED; - ret = uart_add_one_port(&atmel_uart, &port->uart); + ret = uart_add_one_port(&atmel_uart, &atmel_port->uart); if (ret) goto err_add_port; #ifdef CONFIG_SERIAL_ATMEL_CONSOLE - if (atmel_is_console_port(&port->uart) + if (atmel_is_console_port(&atmel_port->uart) && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) { /* * The serial core enabled the clock for us, so undo * the clk_prepare_enable() in atmel_console_setup() */ - clk_disable_unprepare(port->clk); + clk_disable_unprepare(atmel_port->clk); } #endif device_init_wakeup(&pdev->dev, 1); - platform_set_drvdata(pdev, port); + platform_set_drvdata(pdev, atmel_port); /* * The peripheral clock has been disabled by atmel_init_port(): * enable it before accessing I/O registers */ - clk_prepare_enable(port->clk); + clk_prepare_enable(atmel_port->clk); if (rs485_enabled) { - atmel_uart_writel(&port->uart, ATMEL_US_MR, + atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR, ATMEL_US_USMODE_NORMAL); - atmel_uart_writel(&port->uart, ATMEL_US_CR, ATMEL_US_RTSEN); + atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR, + ATMEL_US_RTSEN); } /* * Get port name of usart or uart */ - atmel_get_ip_name(&port->uart); + atmel_get_ip_name(&atmel_port->uart); /* * The peripheral clock can now safely be disabled till the port * is used */ - clk_disable_unprepare(port->clk); + clk_disable_unprepare(atmel_port->clk); return 0; err_add_port: - kfree(port->rx_ring.buf); - port->rx_ring.buf = NULL; + kfree(atmel_port->rx_ring.buf); + atmel_port->rx_ring.buf = NULL; err_alloc_ring: - if (!atmel_is_console_port(&port->uart)) { - clk_put(port->clk); - port->clk = NULL; + if (!atmel_is_console_port(&atmel_port->uart)) { + clk_put(atmel_port->clk); + atmel_port->clk = NULL; } err_clear_bit: - clear_bit(port->uart.line, atmel_ports_in_use); + clear_bit(atmel_port->uart.line, atmel_ports_in_use); err: return ret; } +/* + * Even if the driver is not modular, it makes sense to be able to + * unbind a device: there can be many bound devices, and there are + * situations where dynamic binding and unbinding can be useful. + * + * For example, a connected device can require a specific firmware update + * protocol that needs bitbanging on IO lines, but use the regular serial + * port in the normal case. + */ +static int atmel_serial_remove(struct platform_device *pdev) +{ + struct uart_port *port = platform_get_drvdata(pdev); + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + int ret = 0; + + tasklet_kill(&atmel_port->tasklet); + + device_init_wakeup(&pdev->dev, 0); + + ret = uart_remove_one_port(&atmel_uart, port); + + kfree(atmel_port->rx_ring.buf); + + /* "port" is allocated statically, so we shouldn't free it */ + + clear_bit(port->line, atmel_ports_in_use); + + clk_put(atmel_port->clk); + atmel_port->clk = NULL; + + return ret; +} + static struct platform_driver atmel_serial_driver = { .probe = atmel_serial_probe, + .remove = atmel_serial_remove, .suspend = atmel_serial_suspend, .resume = atmel_serial_resume, .driver = { .name = "atmel_usart", .of_match_table = of_match_ptr(atmel_serial_dt_ids), - .suppress_bind_attrs = true, }, }; diff --git a/drivers/tty/serial/clps711x.c b/drivers/tty/serial/clps711x.c index b3a4e0cdddaa..5beafd2d2218 100644 --- a/drivers/tty/serial/clps711x.c +++ b/drivers/tty/serial/clps711x.c @@ -450,6 +450,7 @@ static int uart_clps711x_probe(struct platform_device *pdev) struct clps711x_port *s; struct resource *res; struct clk *uart_clk; + int irq; if (index < 0 || index >= UART_CLPS711X_NR) return -EINVAL; @@ -467,12 +468,13 @@ static int uart_clps711x_probe(struct platform_device *pdev) if (IS_ERR(s->port.membase)) return PTR_ERR(s->port.membase); - s->port.irq = platform_get_irq(pdev, 0); - if (IS_ERR_VALUE(s->port.irq)) - return s->port.irq; + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + s->port.irq = irq; s->rx_irq = platform_get_irq(pdev, 1); - if (IS_ERR_VALUE(s->rx_irq)) + if (s->rx_irq < 0) return s->rx_irq; if (!np) { diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c index f13f2ebd215b..c0172bf54a9b 100644 --- a/drivers/tty/serial/crisv10.c +++ b/drivers/tty/serial/crisv10.c @@ -1413,9 +1413,8 @@ rs_stop(struct tty_struct *tty) xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty)); xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop); - if (tty->termios.c_iflag & IXON ) { + if (I_IXON(tty)) xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); - } *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; local_irq_restore(flags); @@ -1436,9 +1435,8 @@ rs_start(struct tty_struct *tty) info->xmit.tail,SERIAL_XMIT_SIZE))); xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty)); xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable); - if (tty->termios.c_iflag & IXON ) { + if (I_IXON(tty)) xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); - } *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; if (!info->uses_dma_out && @@ -2968,7 +2966,7 @@ static int rs_raw_write(struct tty_struct *tty, local_save_flags(flags); DFLOW(DEBUG_LOG(info->line, "write count %i ", count)); - DFLOW(DEBUG_LOG(info->line, "ldisc %i\n", tty->ldisc.chars_in_buffer(tty))); + DFLOW(DEBUG_LOG(info->line, "ldisc\n")); /* The local_irq_disable/restore_flags pairs below are needed @@ -3161,13 +3159,12 @@ rs_throttle(struct tty_struct * tty) { struct e100_serial *info = (struct e100_serial *)tty->driver_data; #ifdef SERIAL_DEBUG_THROTTLE - printk("throttle %s: %lu....\n", tty_name(tty), - (unsigned long)tty->ldisc.chars_in_buffer(tty)); + printk("throttle %s ....\n", tty_name(tty)); #endif - DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty))); + DFLOW(DEBUG_LOG(info->line,"rs_throttle\n")); /* Do RTS before XOFF since XOFF might take some time */ - if (tty->termios.c_cflag & CRTSCTS) { + if (C_CRTSCTS(tty)) { /* Turn off RTS line */ e100_rts(info, 0); } @@ -3181,13 +3178,12 @@ rs_unthrottle(struct tty_struct * tty) { struct e100_serial *info = (struct e100_serial *)tty->driver_data; #ifdef SERIAL_DEBUG_THROTTLE - printk("unthrottle %s: %lu....\n", tty_name(tty), - (unsigned long)tty->ldisc.chars_in_buffer(tty)); + printk("unthrottle %s ....\n", tty_name(tty)); #endif - DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty))); + DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc\n")); DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count)); /* Do RTS before XOFF since XOFF might take some time */ - if (tty->termios.c_cflag & CRTSCTS) { + if (C_CRTSCTS(tty)) { /* Assert RTS line */ e100_rts(info, 1); } @@ -3555,8 +3551,7 @@ rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) change_speed(info); /* Handle turning off CRTSCTS */ - if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios.c_cflag & CRTSCTS)) + if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) rs_start(tty); } @@ -3615,7 +3610,6 @@ rs_close(struct tty_struct *tty, struct file * filp) local_irq_restore(flags); return; } - info->port.flags |= ASYNC_CLOSING; /* * Now we wait for the transmit buffer to clear; and we notify * the line discipline to only process XON/XOFF characters. @@ -3654,7 +3648,7 @@ rs_close(struct tty_struct *tty, struct file * filp) schedule_timeout_interruptible(info->port.close_delay); wake_up_interruptible(&info->port.open_wait); } - info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); + info->port.flags &= ~ASYNC_NORMAL_ACTIVE; local_irq_restore(flags); /* port closed */ @@ -3767,9 +3761,8 @@ block_til_ready(struct tty_struct *tty, struct file * filp, return 0; } - if (tty->termios.c_cflag & CLOCAL) { - do_clocal = 1; - } + if (C_CLOCAL(tty)) + do_clocal = 1; /* * Block waiting for the carrier detect and the line to become diff --git a/drivers/tty/serial/digicolor-usart.c b/drivers/tty/serial/digicolor-usart.c index a80cdad114f3..02ad6953b167 100644 --- a/drivers/tty/serial/digicolor-usart.c +++ b/drivers/tty/serial/digicolor-usart.c @@ -453,7 +453,7 @@ static struct uart_driver digicolor_uart = { static int digicolor_uart_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; - int ret, index; + int irq, ret, index; struct digicolor_port *dp; struct resource *res; struct clk *uart_clk; @@ -481,9 +481,10 @@ static int digicolor_uart_probe(struct platform_device *pdev) if (IS_ERR(dp->port.membase)) return PTR_ERR(dp->port.membase); - dp->port.irq = platform_get_irq(pdev, 0); - if (IS_ERR_VALUE(dp->port.irq)) - return dp->port.irq; + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + dp->port.irq = irq; dp->port.iotype = UPIO_MEM; dp->port.uartclk = clk_get_rate(uart_clk); diff --git a/drivers/tty/serial/earlycon.c b/drivers/tty/serial/earlycon.c index 3f2423690d01..067783f0523c 100644 --- a/drivers/tty/serial/earlycon.c +++ b/drivers/tty/serial/earlycon.c @@ -19,7 +19,8 @@ #include <linux/io.h> #include <linux/serial_core.h> #include <linux/sizes.h> -#include <linux/mod_devicetable.h> +#include <linux/of.h> +#include <linux/of_fdt.h> #ifdef CONFIG_FIX_EARLYCON_MEM #include <asm/fixmap.h> @@ -28,22 +29,15 @@ #include <asm/serial.h> static struct console early_con = { - .name = "uart", /* 8250 console switch requires this name */ + .name = "uart", /* fixed up at earlycon registration */ .flags = CON_PRINTBUFFER | CON_BOOT, - .index = -1, + .index = 0, }; static struct earlycon_device early_console_dev = { .con = &early_con, }; -extern struct earlycon_id __earlycon_table[]; -static const struct earlycon_id __earlycon_table_sentinel - __used __section(__earlycon_table_end); - -static const struct of_device_id __earlycon_of_table_sentinel - __used __section(__earlycon_of_table_end); - static void __iomem * __init earlycon_map(unsigned long paddr, size_t size) { void __iomem *base; @@ -61,6 +55,39 @@ static void __iomem * __init earlycon_map(unsigned long paddr, size_t size) return base; } +static void __init earlycon_init(struct earlycon_device *device, + const char *name) +{ + struct console *earlycon = device->con; + struct uart_port *port = &device->port; + const char *s; + size_t len; + + /* scan backwards from end of string for first non-numeral */ + for (s = name + strlen(name); + s > name && s[-1] >= '0' && s[-1] <= '9'; + s--) + ; + if (*s) + earlycon->index = simple_strtoul(s, NULL, 10); + len = s - name; + strlcpy(earlycon->name, name, min(len + 1, sizeof(earlycon->name))); + earlycon->data = &early_console_dev; + + if (port->iotype == UPIO_MEM || port->iotype == UPIO_MEM16 || + port->iotype == UPIO_MEM32 || port->iotype == UPIO_MEM32BE) + pr_info("%s%d at MMIO%s %pa (options '%s')\n", + earlycon->name, earlycon->index, + (port->iotype == UPIO_MEM) ? "" : + (port->iotype == UPIO_MEM16) ? "16" : + (port->iotype == UPIO_MEM32) ? "32" : "32be", + &port->mapbase, device->options); + else + pr_info("%s%d at I/O port 0x%lx (options '%s')\n", + earlycon->name, earlycon->index, + port->iobase, device->options); +} + static int __init parse_options(struct earlycon_device *device, char *options) { struct uart_port *port = &device->port; @@ -97,19 +124,6 @@ static int __init parse_options(struct earlycon_device *device, char *options) strlcpy(device->options, options, length); } - if (port->iotype == UPIO_MEM || port->iotype == UPIO_MEM16 || - port->iotype == UPIO_MEM32 || port->iotype == UPIO_MEM32BE) - pr_info("Early serial console at MMIO%s 0x%llx (options '%s')\n", - (port->iotype == UPIO_MEM) ? "" : - (port->iotype == UPIO_MEM16) ? "16" : - (port->iotype == UPIO_MEM32) ? "32" : "32be", - (unsigned long long)port->mapbase, - device->options); - else - pr_info("Early serial console at I/O port 0x%lx (options '%s')\n", - port->iobase, - device->options); - return 0; } @@ -127,7 +141,7 @@ static int __init register_earlycon(char *buf, const struct earlycon_id *match) if (port->mapbase) port->membase = earlycon_map(port->mapbase, 64); - early_console_dev.con->data = &early_console_dev; + earlycon_init(&early_console_dev, match->name); err = match->setup(&early_console_dev, buf); if (err < 0) return err; @@ -166,7 +180,7 @@ int __init setup_earlycon(char *buf) if (early_con.flags & CON_ENABLED) return -EALREADY; - for (match = __earlycon_table; match->name[0]; match++) { + for (match = __earlycon_table; match < __earlycon_table_end; match++) { size_t len = strlen(match->name); if (strncmp(buf, match->name, len)) @@ -204,20 +218,62 @@ static int __init param_setup_earlycon(char *buf) } early_param("earlycon", param_setup_earlycon); -int __init of_setup_earlycon(unsigned long addr, - int (*setup)(struct earlycon_device *, const char *)) +#ifdef CONFIG_OF_EARLY_FLATTREE + +int __init of_setup_earlycon(const struct earlycon_id *match, + unsigned long node, + const char *options) { int err; struct uart_port *port = &early_console_dev.port; + const __be32 *val; + bool big_endian; + u64 addr; spin_lock_init(&port->lock); port->iotype = UPIO_MEM; + addr = of_flat_dt_translate_address(node); + if (addr == OF_BAD_ADDR) { + pr_warn("[%s] bad address\n", match->name); + return -ENXIO; + } port->mapbase = addr; port->uartclk = BASE_BAUD * 16; - port->membase = earlycon_map(addr, SZ_4K); + port->membase = earlycon_map(port->mapbase, SZ_4K); + + val = of_get_flat_dt_prop(node, "reg-offset", NULL); + if (val) + port->mapbase += be32_to_cpu(*val); + val = of_get_flat_dt_prop(node, "reg-shift", NULL); + if (val) + port->regshift = be32_to_cpu(*val); + big_endian = of_get_flat_dt_prop(node, "big-endian", NULL) != NULL || + (IS_ENABLED(CONFIG_CPU_BIG_ENDIAN) && + of_get_flat_dt_prop(node, "native-endian", NULL) != NULL); + val = of_get_flat_dt_prop(node, "reg-io-width", NULL); + if (val) { + switch (be32_to_cpu(*val)) { + case 1: + port->iotype = UPIO_MEM; + break; + case 2: + port->iotype = UPIO_MEM16; + break; + case 4: + port->iotype = (big_endian) ? UPIO_MEM32BE : UPIO_MEM32; + break; + default: + pr_warn("[%s] unsupported reg-io-width\n", match->name); + return -EINVAL; + } + } - early_console_dev.con->data = &early_console_dev; - err = setup(&early_console_dev, NULL); + if (options) { + strlcpy(early_console_dev.options, options, + sizeof(early_console_dev.options)); + } + earlycon_init(&early_console_dev, match->name); + err = match->setup(&early_console_dev, options); if (err < 0) return err; if (!early_console_dev.con->write) @@ -227,3 +283,5 @@ int __init of_setup_earlycon(unsigned long addr, register_console(early_console_dev.con); return 0; } + +#endif /* CONFIG_OF_EARLY_FLATTREE */ diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c index 88246f7e435a..2085a6cfa44b 100644 --- a/drivers/tty/serial/ifx6x60.c +++ b/drivers/tty/serial/ifx6x60.c @@ -395,8 +395,10 @@ static int ifx_spi_decode_spi_header(unsigned char *buffer, int *length, if (h1 == 0 && h2 == 0) { *received_cts = 0; + *more = 0; return IFX_SPI_HEADER_0; } else if (h1 == 0xffff && h2 == 0xffff) { + *more = 0; /* spi_slave_cts remains as it was */ return IFX_SPI_HEADER_F; } @@ -688,6 +690,7 @@ static void ifx_spi_complete(void *ctx) ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD, (size_t)actual_length); } else { + more = 0; dev_dbg(&ifx_dev->spi_dev->dev, "SPI transfer error %d", ifx_dev->spi_msg.status); } diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index 9362f54c816c..231e7d5caf6c 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -2166,7 +2166,8 @@ static int imx_serial_port_suspend(struct device *dev) uart_suspend_port(&imx_reg, &sport->port); - return 0; + /* Needed to enable clock in suspend_noirq */ + return clk_prepare(sport->clk_ipg); } static int imx_serial_port_resume(struct device *dev) @@ -2179,6 +2180,8 @@ static int imx_serial_port_resume(struct device *dev) uart_resume_port(&imx_reg, &sport->port); + clk_unprepare(sport->clk_ipg); + return 0; } diff --git a/drivers/tty/serial/jsm/jsm_tty.c b/drivers/tty/serial/jsm/jsm_tty.c index 524e86ab3cae..c5ddfe542451 100644 --- a/drivers/tty/serial/jsm/jsm_tty.c +++ b/drivers/tty/serial/jsm/jsm_tty.c @@ -529,7 +529,6 @@ void jsm_input(struct jsm_channel *ch) int data_len; unsigned long lock_flags; int len = 0; - int n = 0; int s = 0; int i = 0; @@ -569,8 +568,7 @@ void jsm_input(struct jsm_channel *ch) *If the device is not open, or CREAD is off, flush *input data and return immediately. */ - if (!tp || - !(tp->termios.c_cflag & CREAD) ) { + if (!tp || !C_CREAD(tp)) { jsm_dbg(READ, &ch->ch_bd->pci_dev, "input. dropping %d bytes on port %d...\n", @@ -598,16 +596,15 @@ void jsm_input(struct jsm_channel *ch) jsm_dbg(READ, &ch->ch_bd->pci_dev, "start 2\n"); len = tty_buffer_request_room(port, data_len); - n = len; /* - * n now contains the most amount of data we can copy, + * len now contains the most amount of data we can copy, * bounded either by the flip buffer size or the amount * of data the card actually has pending... */ - while (n) { + while (len) { s = ((head >= tail) ? head : RQUEUESIZE) - tail; - s = min(s, n); + s = min(s, len); if (s <= 0) break; @@ -638,7 +635,7 @@ void jsm_input(struct jsm_channel *ch) tty_insert_flip_string(port, ch->ch_rqueue + tail, s); } tail += s; - n -= s; + len -= s; /* Flip queue if needed */ tail &= rmask; } diff --git a/drivers/tty/serial/m32r_sio.c b/drivers/tty/serial/m32r_sio.c index 0eeb64f2499c..68765f7c2645 100644 --- a/drivers/tty/serial/m32r_sio.c +++ b/drivers/tty/serial/m32r_sio.c @@ -47,59 +47,26 @@ #define BAUD_RATE 115200 #include <linux/serial_core.h> -#include "m32r_sio.h" #include "m32r_sio_reg.h" -/* - * Debugging. - */ -#if 0 -#define DEBUG_AUTOCONF(fmt...) printk(fmt) -#else -#define DEBUG_AUTOCONF(fmt...) do { } while (0) -#endif - -#if 0 -#define DEBUG_INTR(fmt...) printk(fmt) -#else -#define DEBUG_INTR(fmt...) do { } while (0) -#endif - #define PASS_LIMIT 256 -#define BASE_BAUD 115200 - /* Standard COM flags */ #define STD_COM_FLAGS (UPF_BOOT_AUTOCONF | UPF_SKIP_TEST) -/* - * SERIAL_PORT_DFNS tells us about built-in ports that have no - * standard enumeration mechanism. Platforms that can find all - * serial ports via mechanisms like ACPI or PCI need not supply it. - */ +static const struct { + unsigned int port; + unsigned int irq; +} old_serial_port[] = { #if defined(CONFIG_PLAT_USRV) - -#define SERIAL_PORT_DFNS \ - /* UART CLK PORT IRQ FLAGS */ \ - { 0, BASE_BAUD, 0x3F8, PLD_IRQ_UART0, STD_COM_FLAGS }, /* ttyS0 */ \ - { 0, BASE_BAUD, 0x2F8, PLD_IRQ_UART1, STD_COM_FLAGS }, /* ttyS1 */ - -#else /* !CONFIG_PLAT_USRV */ - -#if defined(CONFIG_SERIAL_M32R_PLDSIO) -#define SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, ((unsigned long)PLD_ESIO0CR), PLD_IRQ_SIO0_RCV, \ - STD_COM_FLAGS }, /* ttyS0 */ + /* PORT IRQ FLAGS */ + { 0x3F8, PLD_IRQ_UART0 }, /* ttyS0 */ + { 0x2F8, PLD_IRQ_UART1 }, /* ttyS1 */ +#elif defined(CONFIG_SERIAL_M32R_PLDSIO) + { ((unsigned long)PLD_ESIO0CR), PLD_IRQ_SIO0_RCV }, /* ttyS0 */ #else -#define SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, M32R_SIO_OFFSET, M32R_IRQ_SIO0_R, \ - STD_COM_FLAGS }, /* ttyS0 */ + { M32R_SIO_OFFSET, M32R_IRQ_SIO0_R }, /* ttyS0 */ #endif - -#endif /* !CONFIG_PLAT_USRV */ - -static struct old_serial_port old_serial_port[] = { - SERIAL_PORT_DFNS }; #define UART_NR ARRAY_SIZE(old_serial_port) @@ -108,19 +75,7 @@ struct uart_sio_port { struct uart_port port; struct timer_list timer; /* "no irq" timer */ struct list_head list; /* ports on this IRQ */ - unsigned short rev; - unsigned char acr; unsigned char ier; - unsigned char lcr; - unsigned char mcr_mask; /* mask of user bits */ - unsigned char mcr_force; /* mask of forced bits */ - unsigned char lsr_break_flag; - - /* - * We provide a per-port pm hook. - */ - void (*pm)(struct uart_port *port, - unsigned int state, unsigned int old); }; struct irq_info { @@ -345,14 +300,8 @@ static void receive_chars(struct uart_sio_port *up, int *status) */ *status &= up->port.read_status_mask; - if (up->port.line == up->port.cons->index) { - /* Recover the break flag from console xmit */ - *status |= up->lsr_break_flag; - up->lsr_break_flag = 0; - } - if (*status & UART_LSR_BI) { - DEBUG_INTR("handling break...."); + pr_debug("handling break....\n"); flag = TTY_BREAK; } else if (*status & UART_LSR_PE) flag = TTY_PARITY; @@ -413,7 +362,7 @@ static void transmit_chars(struct uart_sio_port *up) if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) uart_write_wakeup(&up->port); - DEBUG_INTR("THRE..."); + pr_debug("THRE...\n"); if (uart_circ_empty(xmit)) m32r_sio_stop_tx(&up->port); @@ -425,7 +374,7 @@ static void transmit_chars(struct uart_sio_port *up) static inline void m32r_sio_handle_port(struct uart_sio_port *up, unsigned int status) { - DEBUG_INTR("status = %x...", status); + pr_debug("status = %x...\n", status); if (status & 0x04) receive_chars(up, &status); @@ -453,7 +402,7 @@ static irqreturn_t m32r_sio_interrupt(int irq, void *dev_id) struct list_head *l, *end = NULL; int pass_counter = 0; - DEBUG_INTR("m32r_sio_interrupt(%d)...", irq); + pr_debug("m32r_sio_interrupt(%d)...\n", irq); #ifdef CONFIG_SERIAL_M32R_PLDSIO // if (irq == PLD_IRQ_SIO0_SND) @@ -493,7 +442,7 @@ static irqreturn_t m32r_sio_interrupt(int irq, void *dev_id) spin_unlock(&i->lock); - DEBUG_INTR("end.\n"); + pr_debug("end.\n"); return IRQ_HANDLED; } @@ -782,20 +731,9 @@ static void m32r_sio_set_termios(struct uart_port *port, serial_out(up, UART_IER, up->ier); - up->lcr = cval; /* Save LCR */ spin_unlock_irqrestore(&up->port.lock, flags); } -static void m32r_sio_pm(struct uart_port *port, unsigned int state, - unsigned int oldstate) -{ - struct uart_sio_port *up = - container_of(port, struct uart_sio_port, port); - - if (up->pm) - up->pm(port, state, oldstate); -} - /* * Resource handling. This is complicated by the fact that resources * depend on the port type. Maybe we should be claiming the standard @@ -932,7 +870,6 @@ static struct uart_ops m32r_sio_pops = { .startup = m32r_sio_startup, .shutdown = m32r_sio_shutdown, .set_termios = m32r_sio_set_termios, - .pm = m32r_sio_pm, .release_port = m32r_sio_release_port, .request_port = m32r_sio_request_port, .config_port = m32r_sio_config_port, @@ -951,15 +888,14 @@ static void __init m32r_sio_init_ports(void) return; first = 0; - for (i = 0, up = m32r_sio_ports; i < ARRAY_SIZE(old_serial_port); - i++, up++) { + for (i = 0, up = m32r_sio_ports; i < UART_NR; i++, up++) { up->port.iobase = old_serial_port[i].port; up->port.irq = irq_canonicalize(old_serial_port[i].irq); - up->port.uartclk = old_serial_port[i].baud_base * 16; - up->port.flags = old_serial_port[i].flags; - up->port.membase = old_serial_port[i].iomem_base; - up->port.iotype = old_serial_port[i].io_type; - up->port.regshift = old_serial_port[i].iomem_reg_shift; + up->port.uartclk = BAUD_RATE * 16; + up->port.flags = STD_COM_FLAGS; + up->port.membase = 0; + up->port.iotype = 0; + up->port.regshift = 0; up->port.ops = &m32r_sio_pops; } } @@ -978,9 +914,6 @@ static void __init m32r_sio_register_ports(struct uart_driver *drv) init_timer(&up->timer); up->timer.function = m32r_sio_timeout; - up->mcr_mask = ~0; - up->mcr_force = 0; - uart_add_one_port(drv, &up->port); } } @@ -1112,28 +1045,6 @@ static struct uart_driver m32r_sio_reg = { .cons = M32R_SIO_CONSOLE, }; -/** - * m32r_sio_suspend_port - suspend one serial port - * @line: serial line number - * - * Suspend one serial port. - */ -void m32r_sio_suspend_port(int line) -{ - uart_suspend_port(&m32r_sio_reg, &m32r_sio_ports[line].port); -} - -/** - * m32r_sio_resume_port - resume one serial port - * @line: serial line number - * - * Resume one serial port. - */ -void m32r_sio_resume_port(int line) -{ - uart_resume_port(&m32r_sio_reg, &m32r_sio_ports[line].port); -} - static int __init m32r_sio_init(void) { int ret, i; @@ -1163,8 +1074,5 @@ static void __exit m32r_sio_exit(void) module_init(m32r_sio_init); module_exit(m32r_sio_exit); -EXPORT_SYMBOL(m32r_sio_suspend_port); -EXPORT_SYMBOL(m32r_sio_resume_port); - MODULE_LICENSE("GPL"); MODULE_DESCRIPTION("Generic M32R SIO serial driver"); diff --git a/drivers/tty/serial/m32r_sio.h b/drivers/tty/serial/m32r_sio.h deleted file mode 100644 index 8129824496c6..000000000000 --- a/drivers/tty/serial/m32r_sio.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * m32r_sio.h - * - * Driver for M32R serial ports - * - * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. - * Based on drivers/serial/8250.h. - * - * Copyright (C) 2001 Russell King. - * Copyright (C) 2004 Hirokazu Takata <takata at linux-m32r.org> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include <linux/pci.h> - -struct m32r_sio_probe { - struct module *owner; - int (*pci_init_one)(struct pci_dev *dev); - void (*pci_remove_one)(struct pci_dev *dev); - void (*pnp_init)(void); -}; - -int m32r_sio_register_probe(struct m32r_sio_probe *probe); -void m32r_sio_unregister_probe(struct m32r_sio_probe *probe); -void m32r_sio_get_irq_map(unsigned int *map); -void m32r_sio_suspend_port(int line); -void m32r_sio_resume_port(int line); - -struct old_serial_port { - unsigned int uart; - unsigned int baud_base; - unsigned int port; - unsigned int irq; - unsigned int flags; - unsigned char io_type; - unsigned char __iomem *iomem_base; - unsigned short iomem_reg_shift; -}; - -#define _INLINE_ inline - -#define PROBE_RSA (1 << 0) -#define PROBE_ANY (~0) - -#define HIGH_BITS_OFFSET ((sizeof(long)-sizeof(int))*8) diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c index b12a37bd37b6..024445aa0521 100644 --- a/drivers/tty/serial/meson_uart.c +++ b/drivers/tty/serial/meson_uart.c @@ -78,6 +78,7 @@ /* AML_UART_REG5 bits */ #define AML_UART_BAUD_MASK 0x7fffff #define AML_UART_BAUD_USE BIT(23) +#define AML_UART_BAUD_XTAL BIT(24) #define AML_UART_PORT_NUM 6 #define AML_UART_DEV_NAME "ttyAML" @@ -299,7 +300,12 @@ static void meson_uart_change_speed(struct uart_port *port, unsigned long baud) val = readl(port->membase + AML_UART_REG5); val &= ~AML_UART_BAUD_MASK; - val = ((port->uartclk * 10 / (baud * 4) + 5) / 10) - 1; + if (port->uartclk == 24000000) { + val = ((port->uartclk / 3) / baud) - 1; + val |= AML_UART_BAUD_XTAL; + } else { + val = ((port->uartclk * 10 / (baud * 4) + 5) / 10) - 1; + } val |= AML_UART_BAUD_USE; writel(val, port->membase + AML_UART_REG5); } diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c index 8c3e51314470..3970d6a9aaca 100644 --- a/drivers/tty/serial/mpc52xx_uart.c +++ b/drivers/tty/serial/mpc52xx_uart.c @@ -346,7 +346,7 @@ static irqreturn_t mpc52xx_psc_handle_irq(struct uart_port *port) return mpc5xxx_uart_process_int(port); } -static struct psc_ops mpc52xx_psc_ops = { +static const struct psc_ops mpc52xx_psc_ops = { .fifo_init = mpc52xx_psc_fifo_init, .raw_rx_rdy = mpc52xx_psc_raw_rx_rdy, .raw_tx_rdy = mpc52xx_psc_raw_tx_rdy, @@ -376,7 +376,7 @@ static struct psc_ops mpc52xx_psc_ops = { .get_mr1 = mpc52xx_psc_get_mr1, }; -static struct psc_ops mpc5200b_psc_ops = { +static const struct psc_ops mpc5200b_psc_ops = { .fifo_init = mpc52xx_psc_fifo_init, .raw_rx_rdy = mpc52xx_psc_raw_rx_rdy, .raw_tx_rdy = mpc52xx_psc_raw_tx_rdy, @@ -969,7 +969,7 @@ static u8 mpc5125_psc_get_mr1(struct uart_port *port) return in_8(&PSC_5125(port)->mr1); } -static struct psc_ops mpc5125_psc_ops = { +static const struct psc_ops mpc5125_psc_ops = { .fifo_init = mpc5125_psc_fifo_init, .raw_rx_rdy = mpc5125_psc_raw_rx_rdy, .raw_tx_rdy = mpc5125_psc_raw_tx_rdy, @@ -1004,7 +1004,7 @@ static struct psc_ops mpc5125_psc_ops = { .get_mr1 = mpc5125_psc_get_mr1, }; -static struct psc_ops mpc512x_psc_ops = { +static const struct psc_ops mpc512x_psc_ops = { .fifo_init = mpc512x_psc_fifo_init, .raw_rx_rdy = mpc512x_psc_raw_rx_rdy, .raw_tx_rdy = mpc512x_psc_raw_tx_rdy, diff --git a/drivers/tty/serial/mpsc.c b/drivers/tty/serial/mpsc.c index cadfd1cfae2b..4a3021bcc859 100644 --- a/drivers/tty/serial/mpsc.c +++ b/drivers/tty/serial/mpsc.c @@ -137,8 +137,6 @@ struct mpsc_port_info { /* Internal driver state for this ctlr */ u8 ready; u8 rcv_data; - tcflag_t c_iflag; /* save termios->c_iflag */ - tcflag_t c_cflag; /* save termios->c_cflag */ /* Info passed in from platform */ u8 mirror_regs; /* Need to mirror regs? */ @@ -1407,9 +1405,6 @@ static void mpsc_set_termios(struct uart_port *port, struct ktermios *termios, ulong flags; u32 chr_bits, stop_bits, par; - pi->c_iflag = termios->c_iflag; - pi->c_cflag = termios->c_cflag; - switch (termios->c_cflag & CSIZE) { case CS5: chr_bits = MPSC_MPCR_CL_5; @@ -1870,12 +1865,12 @@ static int mpsc_shared_map_regs(struct platform_device *pd) static void mpsc_shared_unmap_regs(void) { - if (!mpsc_shared_regs.mpsc_routing_base) { + if (mpsc_shared_regs.mpsc_routing_base) { iounmap(mpsc_shared_regs.mpsc_routing_base); release_mem_region(mpsc_shared_regs.mpsc_routing_base_p, MPSC_ROUTING_REG_BLOCK_SIZE); } - if (!mpsc_shared_regs.sdma_intr_base) { + if (mpsc_shared_regs.sdma_intr_base) { iounmap(mpsc_shared_regs.sdma_intr_base); release_mem_region(mpsc_shared_regs.sdma_intr_base_p, MPSC_SDMA_INTR_REG_BLOCK_SIZE); @@ -1891,44 +1886,39 @@ static void mpsc_shared_unmap_regs(void) static int mpsc_shared_drv_probe(struct platform_device *dev) { struct mpsc_shared_pdata *pdata; - int rc = -ENODEV; - - if (dev->id == 0) { - rc = mpsc_shared_map_regs(dev); - if (!rc) { - pdata = (struct mpsc_shared_pdata *) - dev_get_platdata(&dev->dev); - - mpsc_shared_regs.MPSC_MRR_m = pdata->mrr_val; - mpsc_shared_regs.MPSC_RCRR_m= pdata->rcrr_val; - mpsc_shared_regs.MPSC_TCRR_m= pdata->tcrr_val; - mpsc_shared_regs.SDMA_INTR_CAUSE_m = - pdata->intr_cause_val; - mpsc_shared_regs.SDMA_INTR_MASK_m = - pdata->intr_mask_val; - - rc = 0; - } - } + int rc; - return rc; + if (dev->id != 0) + return -ENODEV; + + rc = mpsc_shared_map_regs(dev); + if (rc) + return rc; + + pdata = dev_get_platdata(&dev->dev); + + mpsc_shared_regs.MPSC_MRR_m = pdata->mrr_val; + mpsc_shared_regs.MPSC_RCRR_m= pdata->rcrr_val; + mpsc_shared_regs.MPSC_TCRR_m= pdata->tcrr_val; + mpsc_shared_regs.SDMA_INTR_CAUSE_m = pdata->intr_cause_val; + mpsc_shared_regs.SDMA_INTR_MASK_m = pdata->intr_mask_val; + + return 0; } static int mpsc_shared_drv_remove(struct platform_device *dev) { - int rc = -ENODEV; + if (dev->id != 0) + return -ENODEV; - if (dev->id == 0) { - mpsc_shared_unmap_regs(); - mpsc_shared_regs.MPSC_MRR_m = 0; - mpsc_shared_regs.MPSC_RCRR_m = 0; - mpsc_shared_regs.MPSC_TCRR_m = 0; - mpsc_shared_regs.SDMA_INTR_CAUSE_m = 0; - mpsc_shared_regs.SDMA_INTR_MASK_m = 0; - rc = 0; - } + mpsc_shared_unmap_regs(); + mpsc_shared_regs.MPSC_MRR_m = 0; + mpsc_shared_regs.MPSC_RCRR_m = 0; + mpsc_shared_regs.MPSC_TCRR_m = 0; + mpsc_shared_regs.SDMA_INTR_CAUSE_m = 0; + mpsc_shared_regs.SDMA_INTR_MASK_m = 0; - return rc; + return 0; } static struct platform_driver mpsc_shared_driver = { @@ -1979,10 +1969,6 @@ static int mpsc_drv_map_regs(struct mpsc_port_info *pi, pi->sdma_base_p = r->start; } else { mpsc_resource_err("SDMA base"); - if (pi->mpsc_base) { - iounmap(pi->mpsc_base); - pi->mpsc_base = NULL; - } goto err; } @@ -1993,33 +1979,33 @@ static int mpsc_drv_map_regs(struct mpsc_port_info *pi, pi->brg_base_p = r->start; } else { mpsc_resource_err("BRG base"); - if (pi->mpsc_base) { - iounmap(pi->mpsc_base); - pi->mpsc_base = NULL; - } - if (pi->sdma_base) { - iounmap(pi->sdma_base); - pi->sdma_base = NULL; - } goto err; } return 0; err: + if (pi->sdma_base) { + iounmap(pi->sdma_base); + pi->sdma_base = NULL; + } + if (pi->mpsc_base) { + iounmap(pi->mpsc_base); + pi->mpsc_base = NULL; + } return -ENOMEM; } static void mpsc_drv_unmap_regs(struct mpsc_port_info *pi) { - if (!pi->mpsc_base) { + if (pi->mpsc_base) { iounmap(pi->mpsc_base); release_mem_region(pi->mpsc_base_p, MPSC_REG_BLOCK_SIZE); } - if (!pi->sdma_base) { + if (pi->sdma_base) { iounmap(pi->sdma_base); release_mem_region(pi->sdma_base_p, MPSC_SDMA_REG_BLOCK_SIZE); } - if (!pi->brg_base) { + if (pi->brg_base) { iounmap(pi->brg_base); release_mem_region(pi->brg_base_p, MPSC_BRG_REG_BLOCK_SIZE); } @@ -2073,36 +2059,37 @@ static void mpsc_drv_get_platform_data(struct mpsc_port_info *pi, static int mpsc_drv_probe(struct platform_device *dev) { - struct mpsc_port_info *pi; - int rc = -ENODEV; - - pr_debug("mpsc_drv_probe: Adding MPSC %d\n", dev->id); - - if (dev->id < MPSC_NUM_CTLRS) { - pi = &mpsc_ports[dev->id]; - - rc = mpsc_drv_map_regs(pi, dev); - if (!rc) { - mpsc_drv_get_platform_data(pi, dev, dev->id); - pi->port.dev = &dev->dev; - - rc = mpsc_make_ready(pi); - if (!rc) { - spin_lock_init(&pi->tx_lock); - rc = uart_add_one_port(&mpsc_reg, &pi->port); - if (!rc) { - rc = 0; - } else { - mpsc_release_port((struct uart_port *) - pi); - mpsc_drv_unmap_regs(pi); - } - } else { - mpsc_drv_unmap_regs(pi); - } - } - } + struct mpsc_port_info *pi; + int rc; + + dev_dbg(&dev->dev, "mpsc_drv_probe: Adding MPSC %d\n", dev->id); + + if (dev->id >= MPSC_NUM_CTLRS) + return -ENODEV; + + pi = &mpsc_ports[dev->id]; + + rc = mpsc_drv_map_regs(pi, dev); + if (rc) + return rc; + mpsc_drv_get_platform_data(pi, dev, dev->id); + pi->port.dev = &dev->dev; + + rc = mpsc_make_ready(pi); + if (rc) + goto err_unmap; + + spin_lock_init(&pi->tx_lock); + rc = uart_add_one_port(&mpsc_reg, &pi->port); + if (rc) + goto err_relport; + + return 0; +err_relport: + mpsc_release_port(&pi->port); +err_unmap: + mpsc_drv_unmap_regs(pi); return rc; } @@ -2124,19 +2111,22 @@ static int __init mpsc_drv_init(void) memset(&mpsc_shared_regs, 0, sizeof(mpsc_shared_regs)); rc = uart_register_driver(&mpsc_reg); - if (!rc) { - rc = platform_driver_register(&mpsc_shared_driver); - if (!rc) { - rc = platform_driver_register(&mpsc_driver); - if (rc) { - platform_driver_unregister(&mpsc_shared_driver); - uart_unregister_driver(&mpsc_reg); - } - } else { - uart_unregister_driver(&mpsc_reg); - } - } + if (rc) + return rc; + + rc = platform_driver_register(&mpsc_shared_driver); + if (rc) + goto err_unreg_uart; + rc = platform_driver_register(&mpsc_driver); + if (rc) + goto err_unreg_plat; + + return 0; +err_unreg_plat: + platform_driver_unregister(&mpsc_shared_driver); +err_unreg_uart: + uart_unregister_driver(&mpsc_reg); return rc; } device_initcall(mpsc_drv_init); diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c index dcde955475dc..96d3ce8dc2dc 100644 --- a/drivers/tty/serial/msm_serial.c +++ b/drivers/tty/serial/msm_serial.c @@ -1478,7 +1478,6 @@ msm_serial_early_console_setup(struct earlycon_device *device, const char *opt) device->con->write = msm_serial_early_write; return 0; } -EARLYCON_DECLARE(msm_serial, msm_serial_early_console_setup); OF_EARLYCON_DECLARE(msm_serial, "qcom,msm-uart", msm_serial_early_console_setup); @@ -1500,7 +1499,6 @@ msm_serial_early_console_setup_dm(struct earlycon_device *device, device->con->write = msm_serial_early_write_dm; return 0; } -EARLYCON_DECLARE(msm_serial_dm, msm_serial_early_console_setup_dm); OF_EARLYCON_DECLARE(msm_serial_dm, "qcom,msm-uartdm", msm_serial_early_console_setup_dm); diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c new file mode 100644 index 000000000000..0ff27818bb87 --- /dev/null +++ b/drivers/tty/serial/mvebu-uart.c @@ -0,0 +1,650 @@ +/* +* *************************************************************************** +* Copyright (C) 2015 Marvell International Ltd. +* *************************************************************************** +* This program is free software: you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the Free +* Software Foundation, either version 2 of the License, or any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program. If not, see <http://www.gnu.org/licenses/>. +* *************************************************************************** +*/ + +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/serial.h> +#include <linux/serial_core.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> + +/* Register Map */ +#define UART_RBR 0x00 +#define RBR_BRK_DET BIT(15) +#define RBR_FRM_ERR_DET BIT(14) +#define RBR_PAR_ERR_DET BIT(13) +#define RBR_OVR_ERR_DET BIT(12) + +#define UART_TSH 0x04 + +#define UART_CTRL 0x08 +#define CTRL_SOFT_RST BIT(31) +#define CTRL_TXFIFO_RST BIT(15) +#define CTRL_RXFIFO_RST BIT(14) +#define CTRL_ST_MIRR_EN BIT(13) +#define CTRL_LPBK_EN BIT(12) +#define CTRL_SND_BRK_SEQ BIT(11) +#define CTRL_PAR_EN BIT(10) +#define CTRL_TWO_STOP BIT(9) +#define CTRL_TX_HFL_INT BIT(8) +#define CTRL_RX_HFL_INT BIT(7) +#define CTRL_TX_EMP_INT BIT(6) +#define CTRL_TX_RDY_INT BIT(5) +#define CTRL_RX_RDY_INT BIT(4) +#define CTRL_BRK_DET_INT BIT(3) +#define CTRL_FRM_ERR_INT BIT(2) +#define CTRL_PAR_ERR_INT BIT(1) +#define CTRL_OVR_ERR_INT BIT(0) +#define CTRL_RX_INT (CTRL_RX_RDY_INT | CTRL_BRK_DET_INT |\ + CTRL_FRM_ERR_INT | CTRL_PAR_ERR_INT | CTRL_OVR_ERR_INT) + +#define UART_STAT 0x0c +#define STAT_TX_FIFO_EMP BIT(13) +#define STAT_RX_FIFO_EMP BIT(12) +#define STAT_TX_FIFO_FUL BIT(11) +#define STAT_TX_FIFO_HFL BIT(10) +#define STAT_RX_TOGL BIT(9) +#define STAT_RX_FIFO_FUL BIT(8) +#define STAT_RX_FIFO_HFL BIT(7) +#define STAT_TX_EMP BIT(6) +#define STAT_TX_RDY BIT(5) +#define STAT_RX_RDY BIT(4) +#define STAT_BRK_DET BIT(3) +#define STAT_FRM_ERR BIT(2) +#define STAT_PAR_ERR BIT(1) +#define STAT_OVR_ERR BIT(0) +#define STAT_BRK_ERR (STAT_BRK_DET | STAT_FRM_ERR | STAT_FRM_ERR\ + | STAT_PAR_ERR | STAT_OVR_ERR) + +#define UART_BRDV 0x10 + +#define MVEBU_NR_UARTS 1 + +#define MVEBU_UART_TYPE "mvebu-uart" + +static struct uart_port mvebu_uart_ports[MVEBU_NR_UARTS]; + +struct mvebu_uart_data { + struct uart_port *port; + struct clk *clk; +}; + +/* Core UART Driver Operations */ +static unsigned int mvebu_uart_tx_empty(struct uart_port *port) +{ + unsigned long flags; + unsigned int st; + + spin_lock_irqsave(&port->lock, flags); + st = readl(port->membase + UART_STAT); + spin_unlock_irqrestore(&port->lock, flags); + + return (st & STAT_TX_FIFO_EMP) ? TIOCSER_TEMT : 0; +} + +static unsigned int mvebu_uart_get_mctrl(struct uart_port *port) +{ + return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; +} + +static void mvebu_uart_set_mctrl(struct uart_port *port, + unsigned int mctrl) +{ +/* + * Even if we do not support configuring the modem control lines, this + * function must be proided to the serial core + */ +} + +static void mvebu_uart_stop_tx(struct uart_port *port) +{ + unsigned int ctl = readl(port->membase + UART_CTRL); + + ctl &= ~CTRL_TX_RDY_INT; + writel(ctl, port->membase + UART_CTRL); +} + +static void mvebu_uart_start_tx(struct uart_port *port) +{ + unsigned int ctl = readl(port->membase + UART_CTRL); + + ctl |= CTRL_TX_RDY_INT; + writel(ctl, port->membase + UART_CTRL); +} + +static void mvebu_uart_stop_rx(struct uart_port *port) +{ + unsigned int ctl = readl(port->membase + UART_CTRL); + + ctl &= ~CTRL_RX_INT; + writel(ctl, port->membase + UART_CTRL); +} + +static void mvebu_uart_break_ctl(struct uart_port *port, int brk) +{ + unsigned int ctl; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + ctl = readl(port->membase + UART_CTRL); + if (brk == -1) + ctl |= CTRL_SND_BRK_SEQ; + else + ctl &= ~CTRL_SND_BRK_SEQ; + writel(ctl, port->membase + UART_CTRL); + spin_unlock_irqrestore(&port->lock, flags); +} + +static void mvebu_uart_rx_chars(struct uart_port *port, unsigned int status) +{ + struct tty_port *tport = &port->state->port; + unsigned char ch = 0; + char flag = 0; + + do { + if (status & STAT_RX_RDY) { + ch = readl(port->membase + UART_RBR); + ch &= 0xff; + flag = TTY_NORMAL; + port->icount.rx++; + + if (status & STAT_PAR_ERR) + port->icount.parity++; + } + + if (status & STAT_BRK_DET) { + port->icount.brk++; + status &= ~(STAT_FRM_ERR | STAT_PAR_ERR); + if (uart_handle_break(port)) + goto ignore_char; + } + + if (status & STAT_OVR_ERR) + port->icount.overrun++; + + if (status & STAT_FRM_ERR) + port->icount.frame++; + + if (uart_handle_sysrq_char(port, ch)) + goto ignore_char; + + if (status & port->ignore_status_mask & STAT_PAR_ERR) + status &= ~STAT_RX_RDY; + + status &= port->read_status_mask; + + if (status & STAT_PAR_ERR) + flag = TTY_PARITY; + + status &= ~port->ignore_status_mask; + + if (status & STAT_RX_RDY) + tty_insert_flip_char(tport, ch, flag); + + if (status & STAT_BRK_DET) + tty_insert_flip_char(tport, 0, TTY_BREAK); + + if (status & STAT_FRM_ERR) + tty_insert_flip_char(tport, 0, TTY_FRAME); + + if (status & STAT_OVR_ERR) + tty_insert_flip_char(tport, 0, TTY_OVERRUN); + +ignore_char: + status = readl(port->membase + UART_STAT); + } while (status & (STAT_RX_RDY | STAT_BRK_DET)); + + tty_flip_buffer_push(tport); +} + +static void mvebu_uart_tx_chars(struct uart_port *port, unsigned int status) +{ + struct circ_buf *xmit = &port->state->xmit; + unsigned int count; + unsigned int st; + + if (port->x_char) { + writel(port->x_char, port->membase + UART_TSH); + port->icount.tx++; + port->x_char = 0; + return; + } + + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { + mvebu_uart_stop_tx(port); + return; + } + + for (count = 0; count < port->fifosize; count++) { + writel(xmit->buf[xmit->tail], port->membase + UART_TSH); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + + if (uart_circ_empty(xmit)) + break; + + st = readl(port->membase + UART_STAT); + if (st & STAT_TX_FIFO_FUL) + break; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + if (uart_circ_empty(xmit)) + mvebu_uart_stop_tx(port); +} + +static irqreturn_t mvebu_uart_isr(int irq, void *dev_id) +{ + struct uart_port *port = (struct uart_port *)dev_id; + unsigned int st = readl(port->membase + UART_STAT); + + if (st & (STAT_RX_RDY | STAT_OVR_ERR | STAT_FRM_ERR | STAT_BRK_DET)) + mvebu_uart_rx_chars(port, st); + + if (st & STAT_TX_RDY) + mvebu_uart_tx_chars(port, st); + + return IRQ_HANDLED; +} + +static int mvebu_uart_startup(struct uart_port *port) +{ + int ret; + + writel(CTRL_TXFIFO_RST | CTRL_RXFIFO_RST, + port->membase + UART_CTRL); + udelay(1); + writel(CTRL_RX_INT, port->membase + UART_CTRL); + + ret = request_irq(port->irq, mvebu_uart_isr, port->irqflags, "serial", + port); + if (ret) { + dev_err(port->dev, "failed to request irq\n"); + return ret; + } + + return 0; +} + +static void mvebu_uart_shutdown(struct uart_port *port) +{ + writel(0, port->membase + UART_CTRL); +} + +static void mvebu_uart_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + unsigned long flags; + unsigned int baud; + + spin_lock_irqsave(&port->lock, flags); + + port->read_status_mask = STAT_RX_RDY | STAT_OVR_ERR | + STAT_TX_RDY | STAT_TX_FIFO_FUL; + + if (termios->c_iflag & INPCK) + port->read_status_mask |= STAT_FRM_ERR | STAT_PAR_ERR; + + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= + STAT_FRM_ERR | STAT_PAR_ERR | STAT_OVR_ERR; + + if ((termios->c_cflag & CREAD) == 0) + port->ignore_status_mask |= STAT_RX_RDY | STAT_BRK_ERR; + + if (old) + tty_termios_copy_hw(termios, old); + + baud = uart_get_baud_rate(port, termios, old, 0, 460800); + uart_update_timeout(port, termios->c_cflag, baud); + + spin_unlock_irqrestore(&port->lock, flags); +} + +static const char *mvebu_uart_type(struct uart_port *port) +{ + return MVEBU_UART_TYPE; +} + +static void mvebu_uart_release_port(struct uart_port *port) +{ + /* Nothing to do here */ +} + +static int mvebu_uart_request_port(struct uart_port *port) +{ + return 0; +} + +#ifdef CONFIG_CONSOLE_POLL +static int mvebu_uart_get_poll_char(struct uart_port *port) +{ + unsigned int st = readl(port->membase + UART_STAT); + + if (!(st & STAT_RX_RDY)) + return NO_POLL_CHAR; + + return readl(port->membase + UART_RBR); +} + +static void mvebu_uart_put_poll_char(struct uart_port *port, unsigned char c) +{ + unsigned int st; + + for (;;) { + st = readl(port->membase + UART_STAT); + + if (!(st & STAT_TX_FIFO_FUL)) + break; + + udelay(1); + } + + writel(c, port->membase + UART_TSH); +} +#endif + +static const struct uart_ops mvebu_uart_ops = { + .tx_empty = mvebu_uart_tx_empty, + .set_mctrl = mvebu_uart_set_mctrl, + .get_mctrl = mvebu_uart_get_mctrl, + .stop_tx = mvebu_uart_stop_tx, + .start_tx = mvebu_uart_start_tx, + .stop_rx = mvebu_uart_stop_rx, + .break_ctl = mvebu_uart_break_ctl, + .startup = mvebu_uart_startup, + .shutdown = mvebu_uart_shutdown, + .set_termios = mvebu_uart_set_termios, + .type = mvebu_uart_type, + .release_port = mvebu_uart_release_port, + .request_port = mvebu_uart_request_port, +#ifdef CONFIG_CONSOLE_POLL + .poll_get_char = mvebu_uart_get_poll_char, + .poll_put_char = mvebu_uart_put_poll_char, +#endif +}; + +/* Console Driver Operations */ + +#ifdef CONFIG_SERIAL_MVEBU_CONSOLE +/* Early Console */ +static void mvebu_uart_putc(struct uart_port *port, int c) +{ + unsigned int st; + + for (;;) { + st = readl(port->membase + UART_STAT); + if (!(st & STAT_TX_FIFO_FUL)) + break; + } + + writel(c, port->membase + UART_TSH); + + for (;;) { + st = readl(port->membase + UART_STAT); + if (st & STAT_TX_FIFO_EMP) + break; + } +} + +static void mvebu_uart_putc_early_write(struct console *con, + const char *s, + unsigned n) +{ + struct earlycon_device *dev = con->data; + + uart_console_write(&dev->port, s, n, mvebu_uart_putc); +} + +static int __init +mvebu_uart_early_console_setup(struct earlycon_device *device, + const char *opt) +{ + if (!device->port.membase) + return -ENODEV; + + device->con->write = mvebu_uart_putc_early_write; + + return 0; +} + +EARLYCON_DECLARE(ar3700_uart, mvebu_uart_early_console_setup); +OF_EARLYCON_DECLARE(ar3700_uart, "marvell,armada-3700-uart", + mvebu_uart_early_console_setup); + +static void wait_for_xmitr(struct uart_port *port) +{ + u32 val; + + readl_poll_timeout_atomic(port->membase + UART_STAT, val, + (val & STAT_TX_EMP), 1, 10000); +} + +static void mvebu_uart_console_putchar(struct uart_port *port, int ch) +{ + wait_for_xmitr(port); + writel(ch, port->membase + UART_TSH); +} + +static void mvebu_uart_console_write(struct console *co, const char *s, + unsigned int count) +{ + struct uart_port *port = &mvebu_uart_ports[co->index]; + unsigned long flags; + unsigned int ier; + int locked = 1; + + if (oops_in_progress) + locked = spin_trylock_irqsave(&port->lock, flags); + else + spin_lock_irqsave(&port->lock, flags); + + ier = readl(port->membase + UART_CTRL) & + (CTRL_RX_INT | CTRL_TX_RDY_INT); + writel(0, port->membase + UART_CTRL); + + uart_console_write(port, s, count, mvebu_uart_console_putchar); + + wait_for_xmitr(port); + + if (ier) + writel(ier, port->membase + UART_CTRL); + + if (locked) + spin_unlock_irqrestore(&port->lock, flags); +} + +static int mvebu_uart_console_setup(struct console *co, char *options) +{ + struct uart_port *port; + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (co->index < 0 || co->index >= MVEBU_NR_UARTS) + return -EINVAL; + + port = &mvebu_uart_ports[co->index]; + + if (!port->mapbase || !port->membase) { + pr_debug("console on ttyMV%i not present\n", co->index); + return -ENODEV; + } + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct uart_driver mvebu_uart_driver; + +static struct console mvebu_uart_console = { + .name = "ttyMV", + .write = mvebu_uart_console_write, + .device = uart_console_device, + .setup = mvebu_uart_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &mvebu_uart_driver, +}; + +static int __init mvebu_uart_console_init(void) +{ + register_console(&mvebu_uart_console); + return 0; +} + +console_initcall(mvebu_uart_console_init); + + +#endif /* CONFIG_SERIAL_MVEBU_CONSOLE */ + +static struct uart_driver mvebu_uart_driver = { + .owner = THIS_MODULE, + .driver_name = "mvebu_serial", + .dev_name = "ttyMV", + .nr = MVEBU_NR_UARTS, +#ifdef CONFIG_SERIAL_MVEBU_CONSOLE + .cons = &mvebu_uart_console, +#endif +}; + +static int mvebu_uart_probe(struct platform_device *pdev) +{ + struct resource *reg = platform_get_resource(pdev, IORESOURCE_MEM, 0); + struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + struct uart_port *port; + struct mvebu_uart_data *data; + int ret; + + if (!reg || !irq) { + dev_err(&pdev->dev, "no registers/irq defined\n"); + return -EINVAL; + } + + port = &mvebu_uart_ports[0]; + + spin_lock_init(&port->lock); + + port->dev = &pdev->dev; + port->type = PORT_MVEBU; + port->ops = &mvebu_uart_ops; + port->regshift = 0; + + port->fifosize = 32; + port->iotype = UPIO_MEM32; + port->flags = UPF_FIXED_PORT; + port->line = 0; /* single port: force line number to 0 */ + + port->irq = irq->start; + port->irqflags = 0; + port->mapbase = reg->start; + + port->membase = devm_ioremap_resource(&pdev->dev, reg); + if (IS_ERR(port->membase)) + return -PTR_ERR(port->membase); + + data = devm_kzalloc(&pdev->dev, sizeof(struct mvebu_uart_data), + GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->port = port; + + port->private_data = data; + platform_set_drvdata(pdev, data); + + ret = uart_add_one_port(&mvebu_uart_driver, port); + if (ret) + return ret; + return 0; +} + +static int mvebu_uart_remove(struct platform_device *pdev) +{ + struct mvebu_uart_data *data = platform_get_drvdata(pdev); + + uart_remove_one_port(&mvebu_uart_driver, data->port); + data->port->private_data = NULL; + data->port->mapbase = 0; + return 0; +} + +/* Match table for of_platform binding */ +static const struct of_device_id mvebu_uart_of_match[] = { + { .compatible = "marvell,armada-3700-uart", }, + {} +}; +MODULE_DEVICE_TABLE(of, mvebu_uart_of_match); + +static struct platform_driver mvebu_uart_platform_driver = { + .probe = mvebu_uart_probe, + .remove = mvebu_uart_remove, + .driver = { + .owner = THIS_MODULE, + .name = "mvebu-uart", + .of_match_table = of_match_ptr(mvebu_uart_of_match), + }, +}; + +static int __init mvebu_uart_init(void) +{ + int ret; + + ret = uart_register_driver(&mvebu_uart_driver); + if (ret) + return ret; + + ret = platform_driver_register(&mvebu_uart_platform_driver); + if (ret) + uart_unregister_driver(&mvebu_uart_driver); + + return ret; +} + +static void __exit mvebu_uart_exit(void) +{ + platform_driver_unregister(&mvebu_uart_platform_driver); + uart_unregister_driver(&mvebu_uart_driver); +} + +arch_initcall(mvebu_uart_init); +module_exit(mvebu_uart_exit); + +MODULE_AUTHOR("Wilson Ding <dingwei@marvell.com>"); +MODULE_DESCRIPTION("Marvell Armada-3700 Serial Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c index fa49eb1e2fa2..a2a529994ba5 100644 --- a/drivers/tty/serial/omap-serial.c +++ b/drivers/tty/serial/omap-serial.c @@ -1870,7 +1870,7 @@ static struct platform_driver serial_omap_driver = { .probe = serial_omap_probe, .remove = serial_omap_remove, .driver = { - .name = DRIVER_NAME, + .name = OMAP_SERIAL_DRIVER_NAME, .pm = &serial_omap_dev_pm_ops, .of_match_table = of_match_ptr(omap_serial_of_match), }, diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c index d72cd736bdc6..ac7f8df54406 100644 --- a/drivers/tty/serial/samsung.c +++ b/drivers/tty/serial/samsung.c @@ -601,14 +601,21 @@ static void s3c24xx_serial_rx_drain_fifo(struct s3c24xx_uart_port *ourport) { struct uart_port *port = &ourport->port; unsigned int ufcon, ch, flag, ufstat, uerstat; + unsigned int fifocnt = 0; int max_count = port->fifosize; while (max_count-- > 0) { - ufcon = rd_regl(port, S3C2410_UFCON); - ufstat = rd_regl(port, S3C2410_UFSTAT); - - if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0) - break; + /* + * Receive all characters known to be in FIFO + * before reading FIFO level again + */ + if (fifocnt == 0) { + ufstat = rd_regl(port, S3C2410_UFSTAT); + fifocnt = s3c24xx_serial_rx_fifocnt(ourport, ufstat); + if (fifocnt == 0) + break; + } + fifocnt--; uerstat = rd_regl(port, S3C2410_UERSTAT); ch = rd_regb(port, S3C2410_URXH); @@ -623,6 +630,7 @@ static void s3c24xx_serial_rx_drain_fifo(struct s3c24xx_uart_port *ourport) } } else { if (txe) { + ufcon = rd_regl(port, S3C2410_UFCON); ufcon |= S3C2410_UFCON_RESETRX; wr_regl(port, S3C2410_UFCON, ufcon); rx_enabled(port) = 1; @@ -2451,7 +2459,6 @@ static int __init s3c2410_early_console_setup(struct earlycon_device *device, } OF_EARLYCON_DECLARE(s3c2410, "samsung,s3c2410-uart", s3c2410_early_console_setup); -EARLYCON_DECLARE(s3c2410, s3c2410_early_console_setup); /* S3C2412, S3C2440, S3C64xx */ static struct samsung_early_console_data s3c2440_early_console_data = { @@ -2470,9 +2477,6 @@ OF_EARLYCON_DECLARE(s3c2440, "samsung,s3c2440-uart", s3c2440_early_console_setup); OF_EARLYCON_DECLARE(s3c6400, "samsung,s3c6400-uart", s3c2440_early_console_setup); -EARLYCON_DECLARE(s3c2412, s3c2440_early_console_setup); -EARLYCON_DECLARE(s3c2440, s3c2440_early_console_setup); -EARLYCON_DECLARE(s3c6400, s3c2440_early_console_setup); /* S5PV210, EXYNOS */ static struct samsung_early_console_data s5pv210_early_console_data = { @@ -2489,8 +2493,6 @@ OF_EARLYCON_DECLARE(s5pv210, "samsung,s5pv210-uart", s5pv210_early_console_setup); OF_EARLYCON_DECLARE(exynos4210, "samsung,exynos4210-uart", s5pv210_early_console_setup); -EARLYCON_DECLARE(s5pv210, s5pv210_early_console_setup); -EARLYCON_DECLARE(exynos4210, s5pv210_early_console_setup); #endif MODULE_ALIAS("platform:samsung-uart"); diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c index 13f8d5f70272..025a4264430e 100644 --- a/drivers/tty/serial/sc16is7xx.c +++ b/drivers/tty/serial/sc16is7xx.c @@ -196,14 +196,14 @@ * or (IO6) * - only on 75x/76x */ -#define SC16IS7XX_MSR_CTS_BIT (1 << 0) /* CTS */ -#define SC16IS7XX_MSR_DSR_BIT (1 << 1) /* DSR (IO4) +#define SC16IS7XX_MSR_CTS_BIT (1 << 4) /* CTS */ +#define SC16IS7XX_MSR_DSR_BIT (1 << 5) /* DSR (IO4) * - only on 75x/76x */ -#define SC16IS7XX_MSR_RI_BIT (1 << 2) /* RI (IO7) +#define SC16IS7XX_MSR_RI_BIT (1 << 6) /* RI (IO7) * - only on 75x/76x */ -#define SC16IS7XX_MSR_CD_BIT (1 << 3) /* CD (IO6) +#define SC16IS7XX_MSR_CD_BIT (1 << 7) /* CD (IO6) * - only on 75x/76x */ #define SC16IS7XX_MSR_DELTA_MASK 0x0F /* Any of the delta bits! */ @@ -240,7 +240,7 @@ /* IOControl register bits (Only 750/760) */ #define SC16IS7XX_IOCONTROL_LATCH_BIT (1 << 0) /* Enable input latching */ -#define SC16IS7XX_IOCONTROL_GPIO_BIT (1 << 1) /* Enable GPIO[7:4] */ +#define SC16IS7XX_IOCONTROL_MODEM_BIT (1 << 1) /* Enable GPIO[7:4] as modem pins */ #define SC16IS7XX_IOCONTROL_SRESET_BIT (1 << 3) /* Software Reset */ /* EFCR register bits */ @@ -687,7 +687,7 @@ static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno) case SC16IS7XX_IIR_CTSRTS_SRC: msr = sc16is7xx_port_read(port, SC16IS7XX_MSR_REG); uart_handle_cts_change(port, - !!(msr & SC16IS7XX_MSR_CTS_BIT)); + !!(msr & SC16IS7XX_MSR_DCTS_BIT)); break; case SC16IS7XX_IIR_THRI_SRC: sc16is7xx_handle_tx(port); @@ -761,12 +761,20 @@ static void sc16is7xx_reg_proc(struct kthread_work *ws) memset(&one->config, 0, sizeof(one->config)); spin_unlock_irqrestore(&one->port.lock, irqflags); - if (config.flags & SC16IS7XX_RECONF_MD) + if (config.flags & SC16IS7XX_RECONF_MD) { sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, SC16IS7XX_MCR_LOOP_BIT, (one->port.mctrl & TIOCM_LOOP) ? SC16IS7XX_MCR_LOOP_BIT : 0); - + sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, + SC16IS7XX_MCR_RTS_BIT, + (one->port.mctrl & TIOCM_RTS) ? + SC16IS7XX_MCR_RTS_BIT : 0); + sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, + SC16IS7XX_MCR_DTR_BIT, + (one->port.mctrl & TIOCM_DTR) ? + SC16IS7XX_MCR_DTR_BIT : 0); + } if (config.flags & SC16IS7XX_RECONF_IER) sc16is7xx_port_update(&one->port, SC16IS7XX_IER_REG, config.ier_clear, 0); diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index b1f54ab1818c..a126a603b083 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -171,14 +171,12 @@ static int uart_port_startup(struct tty_struct *tty, struct uart_state *state, */ uart_change_speed(tty, state, NULL); - if (init_hw) { - /* - * Setup the RTS and DTR signals once the - * port is open and ready to respond. - */ - if (tty->termios.c_cflag & CBAUD) - uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR); - } + /* + * Setup the RTS and DTR signals once the + * port is open and ready to respond. + */ + if (init_hw && C_BAUD(tty)) + uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR); } /* @@ -240,7 +238,7 @@ static void uart_shutdown(struct tty_struct *tty, struct uart_state *state) if (uart_console(uport) && tty) uport->cons->cflag = tty->termios.c_cflag; - if (!tty || (tty->termios.c_cflag & HUPCL)) + if (!tty || C_HUPCL(tty)) uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS); uart_port_shutdown(port); @@ -485,12 +483,15 @@ static void uart_change_speed(struct tty_struct *tty, struct uart_state *state, spin_unlock_irq(&uport->lock); } -static inline int __uart_put_char(struct uart_port *port, - struct circ_buf *circ, unsigned char c) +static int uart_put_char(struct tty_struct *tty, unsigned char c) { + struct uart_state *state = tty->driver_data; + struct uart_port *port = state->uart_port; + struct circ_buf *circ; unsigned long flags; int ret = 0; + circ = &state->xmit; if (!circ->buf) return 0; @@ -504,13 +505,6 @@ static inline int __uart_put_char(struct uart_port *port, return ret; } -static int uart_put_char(struct tty_struct *tty, unsigned char ch) -{ - struct uart_state *state = tty->driver_data; - - return __uart_put_char(state->uart_port, &state->xmit, ch); -} - static void uart_flush_chars(struct tty_struct *tty) { uart_start(tty); @@ -639,7 +633,7 @@ static void uart_throttle(struct tty_struct *tty) if (I_IXOFF(tty)) mask |= UPSTAT_AUTOXOFF; - if (tty->termios.c_cflag & CRTSCTS) + if (C_CRTSCTS(tty)) mask |= UPSTAT_AUTORTS; if (port->status & mask) { @@ -647,11 +641,11 @@ static void uart_throttle(struct tty_struct *tty) mask &= ~port->status; } - if (mask & UPSTAT_AUTOXOFF) - uart_send_xchar(tty, STOP_CHAR(tty)); - if (mask & UPSTAT_AUTORTS) uart_clear_mctrl(port, TIOCM_RTS); + + if (mask & UPSTAT_AUTOXOFF) + uart_send_xchar(tty, STOP_CHAR(tty)); } static void uart_unthrottle(struct tty_struct *tty) @@ -662,7 +656,7 @@ static void uart_unthrottle(struct tty_struct *tty) if (I_IXOFF(tty)) mask |= UPSTAT_AUTOXOFF; - if (tty->termios.c_cflag & CRTSCTS) + if (C_CRTSCTS(tty)) mask |= UPSTAT_AUTORTS; if (port->status & mask) { @@ -670,21 +664,25 @@ static void uart_unthrottle(struct tty_struct *tty) mask &= ~port->status; } - if (mask & UPSTAT_AUTOXOFF) - uart_send_xchar(tty, START_CHAR(tty)); - if (mask & UPSTAT_AUTORTS) uart_set_mctrl(port, TIOCM_RTS); + + if (mask & UPSTAT_AUTOXOFF) + uart_send_xchar(tty, START_CHAR(tty)); } -static void do_uart_get_info(struct tty_port *port, - struct serial_struct *retinfo) +static void uart_get_info(struct tty_port *port, struct serial_struct *retinfo) { struct uart_state *state = container_of(port, struct uart_state, port); struct uart_port *uport = state->uart_port; memset(retinfo, 0, sizeof(*retinfo)); + /* + * Ensure the state we copy is consistent and no hardware changes + * occur as we go + */ + mutex_lock(&port->mutex); retinfo->type = uport->type; retinfo->line = uport->line; retinfo->port = uport->iobase; @@ -703,15 +701,6 @@ static void do_uart_get_info(struct tty_port *port, retinfo->io_type = uport->iotype; retinfo->iomem_reg_shift = uport->regshift; retinfo->iomem_base = (void *)(unsigned long)uport->mapbase; -} - -static void uart_get_info(struct tty_port *port, - struct serial_struct *retinfo) -{ - /* Ensure the state we copy is consistent and no hardware changes - occur as we go */ - mutex_lock(&port->mutex); - do_uart_get_info(port, retinfo); mutex_unlock(&port->mutex); } @@ -719,6 +708,7 @@ static int uart_get_info_user(struct tty_port *port, struct serial_struct __user *retinfo) { struct serial_struct tmp; + uart_get_info(port, &tmp); if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) @@ -1391,8 +1381,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp) uport = state->uart_port; port = &state->port; - - pr_debug("uart_close(%d) called\n", uport ? uport->line : -1); + pr_debug("uart_close(%d) called\n", tty->index); if (!port->count || tty_port_close_start(port, tty, filp) == 0) return; @@ -1434,7 +1423,6 @@ static void uart_close(struct tty_struct *tty, struct file *filp) * Wake up anyone trying to open this port. */ clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags); - clear_bit(ASYNCB_CLOSING, &port->flags); spin_unlock_irq(&port->lock); wake_up_interruptible(&port->open_wait); @@ -1510,7 +1498,7 @@ static void uart_hangup(struct tty_struct *tty) struct tty_port *port = &state->port; unsigned long flags; - pr_debug("uart_hangup(%d)\n", state->uart_port->line); + pr_debug("uart_hangup(%d)\n", tty->index); mutex_lock(&port->mutex); if (port->flags & ASYNC_NORMAL_ACTIVE) { @@ -1591,7 +1579,7 @@ static void uart_dtr_rts(struct tty_port *port, int onoff) */ static int uart_open(struct tty_struct *tty, struct file *filp) { - struct uart_driver *drv = (struct uart_driver *)tty->driver->driver_state; + struct uart_driver *drv = tty->driver->driver_state; int retval, line = tty->index; struct uart_state *state = drv->state + line; struct tty_port *port = &state->port; @@ -1633,15 +1621,12 @@ static int uart_open(struct tty_struct *tty, struct file *filp) /* * If we succeeded, wait until the port is ready. */ +err_unlock: mutex_unlock(&port->mutex); if (retval == 0) retval = tty_port_block_til_ready(port, tty, filp); - end: return retval; -err_unlock: - mutex_unlock(&port->mutex); - goto end; } static const char *uart_type(struct uart_port *port) @@ -1700,17 +1685,13 @@ static void uart_line_info(struct seq_file *m, struct uart_driver *drv, int i) seq_printf(m, " tx:%d rx:%d", uport->icount.tx, uport->icount.rx); if (uport->icount.frame) - seq_printf(m, " fe:%d", - uport->icount.frame); + seq_printf(m, " fe:%d", uport->icount.frame); if (uport->icount.parity) - seq_printf(m, " pe:%d", - uport->icount.parity); + seq_printf(m, " pe:%d", uport->icount.parity); if (uport->icount.brk) - seq_printf(m, " brk:%d", - uport->icount.brk); + seq_printf(m, " brk:%d", uport->icount.brk); if (uport->icount.overrun) - seq_printf(m, " oe:%d", - uport->icount.overrun); + seq_printf(m, " oe:%d", uport->icount.overrun); #define INFOBIT(bit, str) \ if (uport->mctrl & (bit)) \ @@ -1745,8 +1726,7 @@ static int uart_proc_show(struct seq_file *m, void *v) struct uart_driver *drv = ttydrv->driver_state; int i; - seq_printf(m, "serinfo:1.0 driver%s%s revision:%s\n", - "", "", ""); + seq_printf(m, "serinfo:1.0 driver%s%s revision:%s\n", "", "", ""); for (i = 0; i < drv->nr; i++) uart_line_info(m, drv, i); return 0; @@ -1895,26 +1875,6 @@ uart_parse_options(char *options, int *baud, int *parity, int *bits, int *flow) } EXPORT_SYMBOL_GPL(uart_parse_options); -struct baud_rates { - unsigned int rate; - unsigned int cflag; -}; - -static const struct baud_rates baud_rates[] = { - { 921600, B921600 }, - { 460800, B460800 }, - { 230400, B230400 }, - { 115200, B115200 }, - { 57600, B57600 }, - { 38400, B38400 }, - { 19200, B19200 }, - { 9600, B9600 }, - { 4800, B4800 }, - { 2400, B2400 }, - { 1200, B1200 }, - { 0, B38400 } -}; - /** * uart_set_options - setup the serial console parameters * @port: pointer to the serial ports uart_port structure @@ -1930,7 +1890,6 @@ uart_set_options(struct uart_port *port, struct console *co, { struct ktermios termios; static struct ktermios dummy; - int i; /* * Ensure that the serial console lock is initialised @@ -1945,16 +1904,8 @@ uart_set_options(struct uart_port *port, struct console *co, memset(&termios, 0, sizeof(struct ktermios)); - termios.c_cflag = CREAD | HUPCL | CLOCAL; - - /* - * Construct a cflag setting. - */ - for (i = 0; baud_rates[i].rate; i++) - if (baud_rates[i].rate <= baud) - break; - - termios.c_cflag |= baud_rates[i].cflag; + termios.c_cflag |= CREAD | HUPCL | CLOCAL; + tty_termios_encode_baud_rate(&termios, baud, baud); if (bits == 7) termios.c_cflag |= CS7; diff --git a/drivers/tty/serial/serial_ks8695.c b/drivers/tty/serial/serial_ks8695.c index b4decf8787de..57f152394af5 100644 --- a/drivers/tty/serial/serial_ks8695.c +++ b/drivers/tty/serial/serial_ks8695.c @@ -554,7 +554,7 @@ static struct uart_port ks8695uart_ports[SERIAL_KS8695_NR] = { .uartclk = KS8695_CLOCK_RATE * 16, .fifosize = 16, .ops = &ks8695uart_pops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, } }; diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c index 226ad23b136c..02147361eaa9 100644 --- a/drivers/tty/serial/serial_mctrl_gpio.c +++ b/drivers/tty/serial/serial_mctrl_gpio.c @@ -20,6 +20,7 @@ #include <linux/gpio/consumer.h> #include <linux/termios.h> #include <linux/serial_core.h> +#include <linux/module.h> #include "serial_mctrl_gpio.h" @@ -249,3 +250,5 @@ void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios) } } EXPORT_SYMBOL_GPL(mctrl_gpio_disable_ms); + +MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c index 4646a9f531ad..0130feb069ae 100644 --- a/drivers/tty/serial/sh-sci.c +++ b/drivers/tty/serial/sh-sci.c @@ -84,6 +84,22 @@ enum SCI_CLKS { SCI_NUM_CLKS }; +/* Bit x set means sampling rate x + 1 is supported */ +#define SCI_SR(x) BIT((x) - 1) +#define SCI_SR_RANGE(x, y) GENMASK((y) - 1, (x) - 1) + +#define SCI_SR_SCIFAB SCI_SR(5) | SCI_SR(7) | SCI_SR(11) | \ + SCI_SR(13) | SCI_SR(16) | SCI_SR(17) | \ + SCI_SR(19) | SCI_SR(27) + +#define min_sr(_port) ffs((_port)->sampling_rate_mask) +#define max_sr(_port) fls((_port)->sampling_rate_mask) + +/* Iterate over all supported sampling rates, from high to low */ +#define for_each_sr(_sr, _port) \ + for ((_sr) = max_sr(_port); (_sr) >= min_sr(_port); (_sr)--) \ + if ((_port)->sampling_rate_mask & SCI_SR((_sr))) + struct sci_port { struct uart_port port; @@ -93,7 +109,7 @@ struct sci_port { unsigned int overrun_mask; unsigned int error_mask; unsigned int error_clear; - unsigned int sampling_rate; + unsigned int sampling_rate_mask; resource_size_t reg_size; /* Break timer */ @@ -637,7 +653,8 @@ static void sci_clear_SCxSR(struct uart_port *port, unsigned int mask) } } -#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE) +#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \ + defined(CONFIG_SERIAL_SH_SCI_EARLYCON) #ifdef CONFIG_CONSOLE_POLL static int sci_poll_get_char(struct uart_port *port) @@ -678,7 +695,8 @@ static void sci_poll_put_char(struct uart_port *port, unsigned char c) serial_port_out(port, SCxTDR, c); sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port)); } -#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE */ +#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE || + CONFIG_SERIAL_SH_SCI_EARLYCON */ static void sci_init_pins(struct uart_port *port, unsigned int cflag) { @@ -1902,19 +1920,13 @@ static int sci_sck_calc(struct sci_port *s, unsigned int bps, unsigned int *srr) { unsigned long freq = s->clk_rates[SCI_SCK]; - unsigned int min_sr, max_sr, sr; int err, min_err = INT_MAX; + unsigned int sr; - if (s->sampling_rate) { - /* SCI(F) has a fixed sampling rate */ - min_sr = max_sr = s->sampling_rate / 2; - } else { - /* HSCIF has a variable 1/(8..32) sampling rate */ - min_sr = 8; - max_sr = 32; - } + if (s->port.type != PORT_HSCIF) + freq *= 2; - for (sr = max_sr; sr >= min_sr; sr--) { + for_each_sr(sr, s) { err = DIV_ROUND_CLOSEST(freq, sr) - bps; if (abs(err) >= abs(min_err)) continue; @@ -1935,19 +1947,13 @@ static int sci_brg_calc(struct sci_port *s, unsigned int bps, unsigned long freq, unsigned int *dlr, unsigned int *srr) { - unsigned int min_sr, max_sr, sr, dl; int err, min_err = INT_MAX; + unsigned int sr, dl; - if (s->sampling_rate) { - /* SCIF has a fixed sampling rate */ - min_sr = max_sr = s->sampling_rate / 2; - } else { - /* HSCIF has a variable 1/(8..32) sampling rate */ - min_sr = 8; - max_sr = 32; - } + if (s->port.type != PORT_HSCIF) + freq *= 2; - for (sr = max_sr; sr >= min_sr; sr--) { + for_each_sr(sr, s) { dl = DIV_ROUND_CLOSEST(freq, sr * bps); dl = clamp(dl, 1U, 65535U); @@ -1973,19 +1979,12 @@ static int sci_scbrr_calc(struct sci_port *s, unsigned int bps, unsigned int *brr, unsigned int *srr, unsigned int *cks) { - unsigned int min_sr, max_sr, shift, sr, br, prediv, scrate, c; unsigned long freq = s->clk_rates[SCI_FCK]; + unsigned int sr, br, prediv, scrate, c; int err, min_err = INT_MAX; - if (s->sampling_rate) { - min_sr = max_sr = s->sampling_rate; - shift = 0; - } else { - /* HSCIF has a variable sample rate */ - min_sr = 8; - max_sr = 32; - shift = 1; - } + if (s->port.type != PORT_HSCIF) + freq *= 2; /* * Find the combination of sample rate and clock select with the @@ -2002,10 +2001,10 @@ static int sci_scbrr_calc(struct sci_port *s, unsigned int bps, * (|D - 0.5| / N * (1 + F))| * NOTE: Usually, treat D for 0.5, F is 0 by this calculation. */ - for (sr = max_sr; sr >= min_sr; sr--) { + for_each_sr(sr, s) { for (c = 0; c <= 3; c++) { /* integerized formulas from HSCIF documentation */ - prediv = sr * (1 << (2 * c + shift)); + prediv = sr * (1 << (2 * c + 1)); /* * We need to calculate: @@ -2062,7 +2061,7 @@ static void sci_reset(struct uart_port *port) static void sci_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { - unsigned int baud, smr_val = 0, scr_val = 0, i; + unsigned int baud, smr_val = SCSMR_ASYNC, scr_val = 0, i; unsigned int brr = 255, cks = 0, srr = 15, dl = 0, sccks = 0; unsigned int brr1 = 255, cks1 = 0, srr1 = 15, dl1 = 0; struct sci_port *s = to_sci_port(port); @@ -2096,8 +2095,7 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios, for (i = 0; i < SCI_NUM_CLKS; i++) max_freq = max(max_freq, s->clk_rates[i]); - baud = uart_get_baud_rate(port, termios, old, 0, - max_freq / max(s->sampling_rate, 8U)); + baud = uart_get_baud_rate(port, termios, old, 0, max_freq / min_sr(s)); if (!baud) goto done; @@ -2185,6 +2183,17 @@ done: uart_update_timeout(port, termios->c_cflag, baud); if (best_clk >= 0) { + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) + switch (srr + 1) { + case 5: smr_val |= SCSMR_SRC_5; break; + case 7: smr_val |= SCSMR_SRC_7; break; + case 11: smr_val |= SCSMR_SRC_11; break; + case 13: smr_val |= SCSMR_SRC_13; break; + case 16: smr_val |= SCSMR_SRC_16; break; + case 17: smr_val |= SCSMR_SRC_17; break; + case 19: smr_val |= SCSMR_SRC_19; break; + case 27: smr_val |= SCSMR_SRC_27; break; + } smr_val |= cks; dev_dbg(port->dev, "SCR 0x%x SMR 0x%x BRR %u CKS 0x%x DL %u SRR %u\n", @@ -2200,7 +2209,8 @@ done: } else { /* Don't touch the bit rate configuration */ scr_val = s->cfg->scscr & (SCSCR_CKE1 | SCSCR_CKE0); - smr_val |= serial_port_in(port, SCSMR) & SCSMR_CKS; + smr_val |= serial_port_in(port, SCSMR) & + (SCSMR_CKEDG | SCSMR_SRC_MASK | SCSMR_CKS); dev_dbg(port->dev, "SCR 0x%x SMR 0x%x\n", scr_val, smr_val); serial_port_out(port, SCSCR, scr_val); serial_port_out(port, SCSMR, smr_val); @@ -2232,6 +2242,16 @@ done: scr_val |= s->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0); dev_dbg(port->dev, "SCSCR 0x%x\n", scr_val); serial_port_out(port, SCSCR, scr_val); + if ((srr + 1 == 5) && + (port->type == PORT_SCIFA || port->type == PORT_SCIFB)) { + /* + * In asynchronous mode, when the sampling rate is 1/5, first + * received data may become invalid on some SCIFA and SCIFB. + * To avoid this problem wait more than 1 serial data time (1 + * bit time x serial data number) after setting SCSCR.RE = 1. + */ + udelay(DIV_ROUND_UP(10 * 1000000, baud)); + } #ifdef CONFIG_SERIAL_SH_SCI_DMA /* @@ -2528,37 +2548,37 @@ static int sci_init_single(struct platform_device *dev, port->fifosize = 256; sci_port->overrun_reg = SCxSR; sci_port->overrun_mask = SCIFA_ORER; - sci_port->sampling_rate = 16; + sci_port->sampling_rate_mask = SCI_SR_SCIFAB; break; case PORT_HSCIF: port->fifosize = 128; sci_port->overrun_reg = SCLSR; sci_port->overrun_mask = SCLSR_ORER; - sci_port->sampling_rate = 0; + sci_port->sampling_rate_mask = SCI_SR_RANGE(8, 32); break; case PORT_SCIFA: port->fifosize = 64; sci_port->overrun_reg = SCxSR; sci_port->overrun_mask = SCIFA_ORER; - sci_port->sampling_rate = 16; + sci_port->sampling_rate_mask = SCI_SR_SCIFAB; break; case PORT_SCIF: port->fifosize = 16; if (p->regtype == SCIx_SH7705_SCIF_REGTYPE) { sci_port->overrun_reg = SCxSR; sci_port->overrun_mask = SCIFA_ORER; - sci_port->sampling_rate = 16; + sci_port->sampling_rate_mask = SCI_SR(16); } else { sci_port->overrun_reg = SCLSR; sci_port->overrun_mask = SCLSR_ORER; - sci_port->sampling_rate = 32; + sci_port->sampling_rate_mask = SCI_SR(32); } break; default: port->fifosize = 1; sci_port->overrun_reg = SCxSR; sci_port->overrun_mask = SCI_ORER; - sci_port->sampling_rate = 32; + sci_port->sampling_rate_mask = SCI_SR(32); break; } @@ -2567,7 +2587,7 @@ static int sci_init_single(struct platform_device *dev, * data override the sampling rate for now. */ if (p->sampling_rate) - sci_port->sampling_rate = p->sampling_rate; + sci_port->sampling_rate_mask = SCI_SR(p->sampling_rate); if (!early) { ret = sci_init_clocks(sci_port, &dev->dev); @@ -2632,7 +2652,8 @@ static void sci_cleanup_single(struct sci_port *port) pm_runtime_disable(port->port.dev); } -#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE +#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \ + defined(CONFIG_SERIAL_SH_SCI_EARLYCON) static void serial_console_putchar(struct uart_port *port, int ch) { sci_poll_put_char(port, ch); @@ -2652,9 +2673,12 @@ static void serial_console_write(struct console *co, const char *s, int locked = 1; local_irq_save(flags); +#if defined(SUPPORT_SYSRQ) if (port->sysrq) locked = 0; - else if (oops_in_progress) + else +#endif + if (oops_in_progress) locked = spin_trylock(&port->lock); else spin_lock(&port->lock); @@ -2764,7 +2788,7 @@ static inline int sci_probe_earlyprintk(struct platform_device *pdev) #define SCI_CONSOLE NULL -#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */ +#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE || CONFIG_SERIAL_SH_SCI_EARLYCON */ static const char banner[] __initconst = "SuperH (H)SCI(F) driver initialized"; @@ -2998,6 +3022,62 @@ static void __exit sci_exit(void) early_platform_init_buffer("earlyprintk", &sci_driver, early_serial_buf, ARRAY_SIZE(early_serial_buf)); #endif +#ifdef CONFIG_SERIAL_SH_SCI_EARLYCON +static struct __init plat_sci_port port_cfg; + +static int __init early_console_setup(struct earlycon_device *device, + int type) +{ + if (!device->port.membase) + return -ENODEV; + + device->port.serial_in = sci_serial_in; + device->port.serial_out = sci_serial_out; + device->port.type = type; + memcpy(&sci_ports[0].port, &device->port, sizeof(struct uart_port)); + sci_ports[0].cfg = &port_cfg; + sci_ports[0].cfg->type = type; + sci_probe_regmap(sci_ports[0].cfg); + port_cfg.scscr = sci_serial_in(&sci_ports[0].port, SCSCR) | + SCSCR_RE | SCSCR_TE; + sci_serial_out(&sci_ports[0].port, SCSCR, port_cfg.scscr); + + device->con->write = serial_console_write; + return 0; +} +static int __init sci_early_console_setup(struct earlycon_device *device, + const char *opt) +{ + return early_console_setup(device, PORT_SCI); +} +static int __init scif_early_console_setup(struct earlycon_device *device, + const char *opt) +{ + return early_console_setup(device, PORT_SCIF); +} +static int __init scifa_early_console_setup(struct earlycon_device *device, + const char *opt) +{ + return early_console_setup(device, PORT_SCIFA); +} +static int __init scifb_early_console_setup(struct earlycon_device *device, + const char *opt) +{ + return early_console_setup(device, PORT_SCIFB); +} +static int __init hscif_early_console_setup(struct earlycon_device *device, + const char *opt) +{ + return early_console_setup(device, PORT_HSCIF); +} + +OF_EARLYCON_DECLARE(sci, "renesas,sci", sci_early_console_setup); +OF_EARLYCON_DECLARE(scif, "renesas,scif", scif_early_console_setup); +OF_EARLYCON_DECLARE(scifa, "renesas,scifa", scifa_early_console_setup); +OF_EARLYCON_DECLARE(scifb, "renesas,scifb", scifb_early_console_setup); +OF_EARLYCON_DECLARE(hscif, "renesas,hscif", hscif_early_console_setup); +#endif /* CONFIG_SERIAL_SH_SCI_EARLYCON */ + module_init(sci_init); module_exit(sci_exit); diff --git a/drivers/tty/serial/sh-sci.h b/drivers/tty/serial/sh-sci.h index fb1760250421..7a4fa185b93e 100644 --- a/drivers/tty/serial/sh-sci.h +++ b/drivers/tty/serial/sh-sci.h @@ -35,12 +35,27 @@ enum { /* SCSMR (Serial Mode Register) */ +#define SCSMR_C_A BIT(7) /* Communication Mode */ +#define SCSMR_CSYNC BIT(7) /* - Clocked synchronous mode */ +#define SCSMR_ASYNC 0 /* - Asynchronous mode */ #define SCSMR_CHR BIT(6) /* 7-bit Character Length */ #define SCSMR_PE BIT(5) /* Parity Enable */ #define SCSMR_ODD BIT(4) /* Odd Parity */ #define SCSMR_STOP BIT(3) /* Stop Bit Length */ #define SCSMR_CKS 0x0003 /* Clock Select */ +/* Serial Mode Register, SCIFA/SCIFB only bits */ +#define SCSMR_CKEDG BIT(12) /* Transmit/Receive Clock Edge Select */ +#define SCSMR_SRC_MASK 0x0700 /* Sampling Control */ +#define SCSMR_SRC_16 0x0000 /* Sampling rate 1/16 */ +#define SCSMR_SRC_5 0x0100 /* Sampling rate 1/5 */ +#define SCSMR_SRC_7 0x0200 /* Sampling rate 1/7 */ +#define SCSMR_SRC_11 0x0300 /* Sampling rate 1/11 */ +#define SCSMR_SRC_13 0x0400 /* Sampling rate 1/13 */ +#define SCSMR_SRC_17 0x0500 /* Sampling rate 1/17 */ +#define SCSMR_SRC_19 0x0600 /* Sampling rate 1/19 */ +#define SCSMR_SRC_27 0x0700 /* Sampling rate 1/27 */ + /* Serial Control Register, SCIFA/SCIFB only bits */ #define SCSCR_TDRQE BIT(15) /* Tx Data Transfer Request Enable */ #define SCSCR_RDRQE BIT(14) /* Rx Data Transfer Request Enable */ diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c index ef26c4a60be4..18971063f95f 100644 --- a/drivers/tty/serial/sprd_serial.c +++ b/drivers/tty/serial/sprd_serial.c @@ -624,8 +624,6 @@ static int __init sprd_early_console_setup( device->con->write = sprd_early_write; return 0; } - -EARLYCON_DECLARE(sprd_serial, sprd_early_console_setup); OF_EARLYCON_DECLARE(sprd_serial, "sprd,sc9836-uart", sprd_early_console_setup); diff --git a/drivers/tty/serial/uartlite.c b/drivers/tty/serial/uartlite.c index b1c6bd3d483f..c9fdfc8bf47f 100644 --- a/drivers/tty/serial/uartlite.c +++ b/drivers/tty/serial/uartlite.c @@ -28,7 +28,7 @@ #define ULITE_NAME "ttyUL" #define ULITE_MAJOR 204 #define ULITE_MINOR 187 -#define ULITE_NR_UARTS 4 +#define ULITE_NR_UARTS 16 /* --------------------------------------------------------------------- * Register definitions @@ -72,7 +72,7 @@ static void uartlite_outbe32(u32 val, void __iomem *addr) iowrite32be(val, addr); } -static struct uartlite_reg_ops uartlite_be = { +static const struct uartlite_reg_ops uartlite_be = { .in = uartlite_inbe32, .out = uartlite_outbe32, }; @@ -87,21 +87,21 @@ static void uartlite_outle32(u32 val, void __iomem *addr) iowrite32(val, addr); } -static struct uartlite_reg_ops uartlite_le = { +static const struct uartlite_reg_ops uartlite_le = { .in = uartlite_inle32, .out = uartlite_outle32, }; static inline u32 uart_in32(u32 offset, struct uart_port *port) { - struct uartlite_reg_ops *reg_ops = port->private_data; + const struct uartlite_reg_ops *reg_ops = port->private_data; return reg_ops->in(port->membase + offset); } static inline void uart_out32(u32 val, u32 offset, struct uart_port *port) { - struct uartlite_reg_ops *reg_ops = port->private_data; + const struct uartlite_reg_ops *reg_ops = port->private_data; reg_ops->out(val, port->membase + offset); } @@ -193,12 +193,15 @@ static int ulite_transmit(struct uart_port *port, int stat) static irqreturn_t ulite_isr(int irq, void *dev_id) { struct uart_port *port = dev_id; - int busy, n = 0; + int stat, busy, n = 0; + unsigned long flags; do { - int stat = uart_in32(ULITE_STATUS, port); + spin_lock_irqsave(&port->lock, flags); + stat = uart_in32(ULITE_STATUS, port); busy = ulite_receive(port, stat); busy |= ulite_transmit(port, stat); + spin_unlock_irqrestore(&port->lock, flags); n++; } while (busy); @@ -259,7 +262,8 @@ static int ulite_startup(struct uart_port *port) { int ret; - ret = request_irq(port->irq, ulite_isr, IRQF_SHARED, "uartlite", port); + ret = request_irq(port->irq, ulite_isr, IRQF_SHARED | IRQF_TRIGGER_RISING, + "uartlite", port); if (ret) return ret; @@ -519,6 +523,47 @@ static int __init ulite_console_init(void) console_initcall(ulite_console_init); +static void early_uartlite_putc(struct uart_port *port, int c) +{ + /* + * Limit how many times we'll spin waiting for TX FIFO status. + * This will prevent lockups if the base address is incorrectly + * set, or any other issue on the UARTLITE. + * This limit is pretty arbitrary, unless we are at about 10 baud + * we'll never timeout on a working UART. + */ + + unsigned retries = 1000000; + /* read status bit - 0x8 offset */ + while (--retries && (readl(port->membase + 8) & (1 << 3))) + ; + + /* Only attempt the iowrite if we didn't timeout */ + /* write to TX_FIFO - 0x4 offset */ + if (retries) + writel(c & 0xff, port->membase + 4); +} + +static void early_uartlite_write(struct console *console, + const char *s, unsigned n) +{ + struct earlycon_device *device = console->data; + uart_console_write(&device->port, s, n, early_uartlite_putc); +} + +static int __init early_uartlite_setup(struct earlycon_device *device, + const char *options) +{ + if (!device->port.membase) + return -ENODEV; + + device->con->write = early_uartlite_write; + return 0; +} +EARLYCON_DECLARE(uartlite, early_uartlite_setup); +OF_EARLYCON_DECLARE(uartlite_b, "xlnx,opb-uartlite-1.00.b", early_uartlite_setup); +OF_EARLYCON_DECLARE(uartlite_a, "xlnx,xps-uartlite-1.00.a", early_uartlite_setup); + #endif /* CONFIG_SERIAL_UARTLITE_CONSOLE */ static struct uart_driver ulite_uart_driver = { diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c index 009e0dbc12d2..cd46e64c4255 100644 --- a/drivers/tty/serial/xilinx_uartps.c +++ b/drivers/tty/serial/xilinx_uartps.c @@ -50,24 +50,24 @@ module_param(rx_timeout, uint, S_IRUGO); MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255"); /* Register offsets for the UART. */ -#define CDNS_UART_CR_OFFSET 0x00 /* Control Register */ -#define CDNS_UART_MR_OFFSET 0x04 /* Mode Register */ -#define CDNS_UART_IER_OFFSET 0x08 /* Interrupt Enable */ -#define CDNS_UART_IDR_OFFSET 0x0C /* Interrupt Disable */ -#define CDNS_UART_IMR_OFFSET 0x10 /* Interrupt Mask */ -#define CDNS_UART_ISR_OFFSET 0x14 /* Interrupt Status */ -#define CDNS_UART_BAUDGEN_OFFSET 0x18 /* Baud Rate Generator */ -#define CDNS_UART_RXTOUT_OFFSET 0x1C /* RX Timeout */ -#define CDNS_UART_RXWM_OFFSET 0x20 /* RX FIFO Trigger Level */ -#define CDNS_UART_MODEMCR_OFFSET 0x24 /* Modem Control */ -#define CDNS_UART_MODEMSR_OFFSET 0x28 /* Modem Status */ -#define CDNS_UART_SR_OFFSET 0x2C /* Channel Status */ -#define CDNS_UART_FIFO_OFFSET 0x30 /* FIFO */ -#define CDNS_UART_BAUDDIV_OFFSET 0x34 /* Baud Rate Divider */ -#define CDNS_UART_FLOWDEL_OFFSET 0x38 /* Flow Delay */ -#define CDNS_UART_IRRX_PWIDTH_OFFSET 0x3C /* IR Min Received Pulse Width */ -#define CDNS_UART_IRTX_PWIDTH_OFFSET 0x40 /* IR Transmitted pulse Width */ -#define CDNS_UART_TXWM_OFFSET 0x44 /* TX FIFO Trigger Level */ +#define CDNS_UART_CR 0x00 /* Control Register */ +#define CDNS_UART_MR 0x04 /* Mode Register */ +#define CDNS_UART_IER 0x08 /* Interrupt Enable */ +#define CDNS_UART_IDR 0x0C /* Interrupt Disable */ +#define CDNS_UART_IMR 0x10 /* Interrupt Mask */ +#define CDNS_UART_ISR 0x14 /* Interrupt Status */ +#define CDNS_UART_BAUDGEN 0x18 /* Baud Rate Generator */ +#define CDNS_UART_RXTOUT 0x1C /* RX Timeout */ +#define CDNS_UART_RXWM 0x20 /* RX FIFO Trigger Level */ +#define CDNS_UART_MODEMCR 0x24 /* Modem Control */ +#define CDNS_UART_MODEMSR 0x28 /* Modem Status */ +#define CDNS_UART_SR 0x2C /* Channel Status */ +#define CDNS_UART_FIFO 0x30 /* FIFO */ +#define CDNS_UART_BAUDDIV 0x34 /* Baud Rate Divider */ +#define CDNS_UART_FLOWDEL 0x38 /* Flow Delay */ +#define CDNS_UART_IRRX_PWIDTH 0x3C /* IR Min Received Pulse Width */ +#define CDNS_UART_IRTX_PWIDTH 0x40 /* IR Transmitted pulse Width */ +#define CDNS_UART_TXWM 0x44 /* TX FIFO Trigger Level */ /* Control Register Bit Definitions */ #define CDNS_UART_CR_STOPBRK 0x00000100 /* Stop TX break */ @@ -126,6 +126,10 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255"); #define CDNS_UART_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */ #define CDNS_UART_IXR_MASK 0x00001FFF /* Valid bit mask */ +#define CDNS_UART_RX_IRQS (CDNS_UART_IXR_PARITY | CDNS_UART_IXR_FRAMING | \ + CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_RXTRIG | \ + CDNS_UART_IXR_TOUT) + /* Goes in read_status_mask for break detection as the HW doesn't do it*/ #define CDNS_UART_IXR_BRK 0x80000000 @@ -172,43 +176,22 @@ struct cdns_uart { #define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \ clk_rate_change_nb); -/** - * cdns_uart_isr - Interrupt handler - * @irq: Irq number - * @dev_id: Id of the port - * - * Return: IRQHANDLED - */ -static irqreturn_t cdns_uart_isr(int irq, void *dev_id) +static void cdns_uart_handle_rx(struct uart_port *port, unsigned int isrstatus) { - struct uart_port *port = (struct uart_port *)dev_id; - unsigned long flags; - unsigned int isrstatus, numbytes; - unsigned int data; - char status = TTY_NORMAL; - - spin_lock_irqsave(&port->lock, flags); - - /* Read the interrupt status register to determine which - * interrupt(s) is/are active. - */ - isrstatus = readl(port->membase + CDNS_UART_ISR_OFFSET); - /* * There is no hardware break detection, so we interpret framing * error with all-zeros data as a break sequence. Most of the time, * there's another non-zero byte at the end of the sequence. */ if (isrstatus & CDNS_UART_IXR_FRAMING) { - while (!(readl(port->membase + CDNS_UART_SR_OFFSET) & + while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_RXEMPTY)) { - if (!readl(port->membase + CDNS_UART_FIFO_OFFSET)) { + if (!readl(port->membase + CDNS_UART_FIFO)) { port->read_status_mask |= CDNS_UART_IXR_BRK; isrstatus &= ~CDNS_UART_IXR_FRAMING; } } - writel(CDNS_UART_IXR_FRAMING, - port->membase + CDNS_UART_ISR_OFFSET); + writel(CDNS_UART_IXR_FRAMING, port->membase + CDNS_UART_ISR); } /* drop byte with parity error if IGNPAR specified */ @@ -218,94 +201,106 @@ static irqreturn_t cdns_uart_isr(int irq, void *dev_id) isrstatus &= port->read_status_mask; isrstatus &= ~port->ignore_status_mask; - if ((isrstatus & CDNS_UART_IXR_TOUT) || - (isrstatus & CDNS_UART_IXR_RXTRIG)) { - /* Receive Timeout Interrupt */ - while (!(readl(port->membase + CDNS_UART_SR_OFFSET) & - CDNS_UART_SR_RXEMPTY)) { - data = readl(port->membase + CDNS_UART_FIFO_OFFSET); - - /* Non-NULL byte after BREAK is garbage (99%) */ - if (data && (port->read_status_mask & - CDNS_UART_IXR_BRK)) { - port->read_status_mask &= ~CDNS_UART_IXR_BRK; - port->icount.brk++; - if (uart_handle_break(port)) - continue; - } + if (!(isrstatus & (CDNS_UART_IXR_TOUT | CDNS_UART_IXR_RXTRIG))) + return; -#ifdef SUPPORT_SYSRQ - /* - * uart_handle_sysrq_char() doesn't work if - * spinlocked, for some reason - */ - if (port->sysrq) { - spin_unlock(&port->lock); - if (uart_handle_sysrq_char(port, - (unsigned char)data)) { - spin_lock(&port->lock); - continue; - } - spin_lock(&port->lock); - } -#endif + while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_RXEMPTY)) { + u32 data; + char status = TTY_NORMAL; - port->icount.rx++; + data = readl(port->membase + CDNS_UART_FIFO); - if (isrstatus & CDNS_UART_IXR_PARITY) { - port->icount.parity++; - status = TTY_PARITY; - } else if (isrstatus & CDNS_UART_IXR_FRAMING) { - port->icount.frame++; - status = TTY_FRAME; - } else if (isrstatus & CDNS_UART_IXR_OVERRUN) { - port->icount.overrun++; - } + /* Non-NULL byte after BREAK is garbage (99%) */ + if (data && (port->read_status_mask & CDNS_UART_IXR_BRK)) { + port->read_status_mask &= ~CDNS_UART_IXR_BRK; + port->icount.brk++; + if (uart_handle_break(port)) + continue; + } + + if (uart_handle_sysrq_char(port, data)) + continue; + + port->icount.rx++; - uart_insert_char(port, isrstatus, CDNS_UART_IXR_OVERRUN, - data, status); + if (isrstatus & CDNS_UART_IXR_PARITY) { + port->icount.parity++; + status = TTY_PARITY; + } else if (isrstatus & CDNS_UART_IXR_FRAMING) { + port->icount.frame++; + status = TTY_FRAME; + } else if (isrstatus & CDNS_UART_IXR_OVERRUN) { + port->icount.overrun++; } - spin_unlock(&port->lock); - tty_flip_buffer_push(&port->state->port); - spin_lock(&port->lock); + + uart_insert_char(port, isrstatus, CDNS_UART_IXR_OVERRUN, + data, status); } + tty_flip_buffer_push(&port->state->port); +} - /* Dispatch an appropriate handler */ - if ((isrstatus & CDNS_UART_IXR_TXEMPTY) == CDNS_UART_IXR_TXEMPTY) { - if (uart_circ_empty(&port->state->xmit)) { - writel(CDNS_UART_IXR_TXEMPTY, - port->membase + CDNS_UART_IDR_OFFSET); - } else { - numbytes = port->fifosize; - /* Break if no more data available in the UART buffer */ - while (numbytes--) { - if (uart_circ_empty(&port->state->xmit)) - break; - /* Get the data from the UART circular buffer - * and write it to the cdns_uart's TX_FIFO - * register. - */ - writel(port->state->xmit.buf[ - port->state->xmit.tail], - port->membase + CDNS_UART_FIFO_OFFSET); - - port->icount.tx++; - - /* Adjust the tail of the UART buffer and wrap - * the buffer if it reaches limit. - */ - port->state->xmit.tail = - (port->state->xmit.tail + 1) & - (UART_XMIT_SIZE - 1); - } +static void cdns_uart_handle_tx(struct uart_port *port) +{ + unsigned int numbytes; - if (uart_circ_chars_pending( - &port->state->xmit) < WAKEUP_CHARS) - uart_write_wakeup(port); - } + if (uart_circ_empty(&port->state->xmit)) { + writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IDR); + return; + } + + numbytes = port->fifosize; + while (numbytes && !uart_circ_empty(&port->state->xmit) && + !(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXFULL)) { + /* + * Get the data from the UART circular buffer + * and write it to the cdns_uart's TX_FIFO + * register. + */ + writel(port->state->xmit.buf[port->state->xmit.tail], + port->membase + CDNS_UART_FIFO); + port->icount.tx++; + + /* + * Adjust the tail of the UART buffer and wrap + * the buffer if it reaches limit. + */ + port->state->xmit.tail = + (port->state->xmit.tail + 1) & (UART_XMIT_SIZE - 1); + + numbytes--; } - writel(isrstatus, port->membase + CDNS_UART_ISR_OFFSET); + if (uart_circ_chars_pending(&port->state->xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); +} + +/** + * cdns_uart_isr - Interrupt handler + * @irq: Irq number + * @dev_id: Id of the port + * + * Return: IRQHANDLED + */ +static irqreturn_t cdns_uart_isr(int irq, void *dev_id) +{ + struct uart_port *port = (struct uart_port *)dev_id; + unsigned long flags; + unsigned int isrstatus; + + spin_lock_irqsave(&port->lock, flags); + + /* Read the interrupt status register to determine which + * interrupt(s) is/are active. + */ + isrstatus = readl(port->membase + CDNS_UART_ISR); + + if (isrstatus & CDNS_UART_RX_IRQS) + cdns_uart_handle_rx(port, isrstatus); + + if ((isrstatus & CDNS_UART_IXR_TXEMPTY) == CDNS_UART_IXR_TXEMPTY) + cdns_uart_handle_tx(port); + + writel(isrstatus, port->membase + CDNS_UART_ISR); /* be sure to release the lock and tty before leaving */ spin_unlock_irqrestore(&port->lock, flags); @@ -395,14 +390,14 @@ static unsigned int cdns_uart_set_baud_rate(struct uart_port *port, &div8); /* Write new divisors to hardware */ - mreg = readl(port->membase + CDNS_UART_MR_OFFSET); + mreg = readl(port->membase + CDNS_UART_MR); if (div8) mreg |= CDNS_UART_MR_CLKSEL; else mreg &= ~CDNS_UART_MR_CLKSEL; - writel(mreg, port->membase + CDNS_UART_MR_OFFSET); - writel(cd, port->membase + CDNS_UART_BAUDGEN_OFFSET); - writel(bdiv, port->membase + CDNS_UART_BAUDDIV_OFFSET); + writel(mreg, port->membase + CDNS_UART_MR); + writel(cd, port->membase + CDNS_UART_BAUDGEN); + writel(bdiv, port->membase + CDNS_UART_BAUDDIV); cdns_uart->baud = baud; return calc_baud; @@ -449,9 +444,9 @@ static int cdns_uart_clk_notifier_cb(struct notifier_block *nb, spin_lock_irqsave(&cdns_uart->port->lock, flags); /* Disable the TX and RX to set baud rate */ - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl_reg, port->membase + CDNS_UART_CR); spin_unlock_irqrestore(&cdns_uart->port->lock, flags); @@ -476,11 +471,11 @@ static int cdns_uart_clk_notifier_cb(struct notifier_block *nb, spin_lock_irqsave(&cdns_uart->port->lock, flags); /* Set TX/RX Reset */ - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl_reg, port->membase + CDNS_UART_CR); - while (readl(port->membase + CDNS_UART_CR_OFFSET) & + while (readl(port->membase + CDNS_UART_CR) & (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST)) cpu_relax(); @@ -489,11 +484,11 @@ static int cdns_uart_clk_notifier_cb(struct notifier_block *nb, * enable bit and RX enable bit to enable the transmitter and * receiver. */ - writel(rx_timeout, port->membase + CDNS_UART_RXTOUT_OFFSET); - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + writel(rx_timeout, port->membase + CDNS_UART_RXTOUT); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS); ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl_reg, port->membase + CDNS_UART_CR); spin_unlock_irqrestore(&cdns_uart->port->lock, flags); @@ -510,43 +505,28 @@ static int cdns_uart_clk_notifier_cb(struct notifier_block *nb, */ static void cdns_uart_start_tx(struct uart_port *port) { - unsigned int status, numbytes = port->fifosize; + unsigned int status; - if (uart_circ_empty(&port->state->xmit) || uart_tx_stopped(port)) + if (uart_tx_stopped(port)) return; - status = readl(port->membase + CDNS_UART_CR_OFFSET); - /* Set the TX enable bit and clear the TX disable bit to enable the + /* + * Set the TX enable bit and clear the TX disable bit to enable the * transmitter. */ - writel((status & ~CDNS_UART_CR_TX_DIS) | CDNS_UART_CR_TX_EN, - port->membase + CDNS_UART_CR_OFFSET); + status = readl(port->membase + CDNS_UART_CR); + status &= ~CDNS_UART_CR_TX_DIS; + status |= CDNS_UART_CR_TX_EN; + writel(status, port->membase + CDNS_UART_CR); - while (numbytes-- && ((readl(port->membase + CDNS_UART_SR_OFFSET) & - CDNS_UART_SR_TXFULL)) != CDNS_UART_SR_TXFULL) { - /* Break if no more data available in the UART buffer */ - if (uart_circ_empty(&port->state->xmit)) - break; + if (uart_circ_empty(&port->state->xmit)) + return; - /* Get the data from the UART circular buffer and - * write it to the cdns_uart's TX_FIFO register. - */ - writel(port->state->xmit.buf[port->state->xmit.tail], - port->membase + CDNS_UART_FIFO_OFFSET); - port->icount.tx++; + cdns_uart_handle_tx(port); - /* Adjust the tail of the UART buffer and wrap - * the buffer if it reaches limit. - */ - port->state->xmit.tail = (port->state->xmit.tail + 1) & - (UART_XMIT_SIZE - 1); - } - writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR_OFFSET); + writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR); /* Enable the TX Empty interrupt */ - writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER_OFFSET); - - if (uart_circ_chars_pending(&port->state->xmit) < WAKEUP_CHARS) - uart_write_wakeup(port); + writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER); } /** @@ -557,10 +537,10 @@ static void cdns_uart_stop_tx(struct uart_port *port) { unsigned int regval; - regval = readl(port->membase + CDNS_UART_CR_OFFSET); + regval = readl(port->membase + CDNS_UART_CR); regval |= CDNS_UART_CR_TX_DIS; /* Disable the transmitter */ - writel(regval, port->membase + CDNS_UART_CR_OFFSET); + writel(regval, port->membase + CDNS_UART_CR); } /** @@ -571,10 +551,13 @@ static void cdns_uart_stop_rx(struct uart_port *port) { unsigned int regval; - regval = readl(port->membase + CDNS_UART_CR_OFFSET); - regval |= CDNS_UART_CR_RX_DIS; + /* Disable RX IRQs */ + writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IDR); + /* Disable the receiver */ - writel(regval, port->membase + CDNS_UART_CR_OFFSET); + regval = readl(port->membase + CDNS_UART_CR); + regval |= CDNS_UART_CR_RX_DIS; + writel(regval, port->membase + CDNS_UART_CR); } /** @@ -587,7 +570,7 @@ static unsigned int cdns_uart_tx_empty(struct uart_port *port) { unsigned int status; - status = readl(port->membase + CDNS_UART_SR_OFFSET) & + status = readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY; return status ? TIOCSER_TEMT : 0; } @@ -605,15 +588,15 @@ static void cdns_uart_break_ctl(struct uart_port *port, int ctl) spin_lock_irqsave(&port->lock, flags); - status = readl(port->membase + CDNS_UART_CR_OFFSET); + status = readl(port->membase + CDNS_UART_CR); if (ctl == -1) writel(CDNS_UART_CR_STARTBRK | status, - port->membase + CDNS_UART_CR_OFFSET); + port->membase + CDNS_UART_CR); else { if ((status & CDNS_UART_CR_STOPBRK) == 0) writel(CDNS_UART_CR_STOPBRK | status, - port->membase + CDNS_UART_CR_OFFSET); + port->membase + CDNS_UART_CR); } spin_unlock_irqrestore(&port->lock, flags); } @@ -636,18 +619,18 @@ static void cdns_uart_set_termios(struct uart_port *port, spin_lock_irqsave(&port->lock, flags); /* Wait for the transmit FIFO to empty before making changes */ - if (!(readl(port->membase + CDNS_UART_CR_OFFSET) & + if (!(readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_TX_DIS)) { - while (!(readl(port->membase + CDNS_UART_SR_OFFSET) & + while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY)) { cpu_relax(); } } /* Disable the TX and RX to set baud rate */ - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl_reg, port->membase + CDNS_UART_CR); /* * Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk @@ -666,20 +649,20 @@ static void cdns_uart_set_termios(struct uart_port *port, uart_update_timeout(port, termios->c_cflag, baud); /* Set TX/RX Reset */ - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl_reg, port->membase + CDNS_UART_CR); /* * Clear the RX disable and TX disable bits and then set the TX enable * bit and RX enable bit to enable the transmitter and receiver. */ - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS); ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl_reg, port->membase + CDNS_UART_CR); - writel(rx_timeout, port->membase + CDNS_UART_RXTOUT_OFFSET); + writel(rx_timeout, port->membase + CDNS_UART_RXTOUT); port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG | CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT; @@ -699,7 +682,7 @@ static void cdns_uart_set_termios(struct uart_port *port, CDNS_UART_IXR_TOUT | CDNS_UART_IXR_PARITY | CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN; - mode_reg = readl(port->membase + CDNS_UART_MR_OFFSET); + mode_reg = readl(port->membase + CDNS_UART_MR); /* Handling Data Size */ switch (termios->c_cflag & CSIZE) { @@ -740,7 +723,7 @@ static void cdns_uart_set_termios(struct uart_port *port, cval |= CDNS_UART_MR_PARITY_NONE; } cval |= mode_reg & 1; - writel(cval, port->membase + CDNS_UART_MR_OFFSET); + writel(cval, port->membase + CDNS_UART_MR); spin_unlock_irqrestore(&port->lock, flags); } @@ -753,63 +736,67 @@ static void cdns_uart_set_termios(struct uart_port *port, */ static int cdns_uart_startup(struct uart_port *port) { - unsigned int retval = 0, status = 0; + int ret; + unsigned long flags; + unsigned int status = 0; - retval = request_irq(port->irq, cdns_uart_isr, 0, CDNS_UART_NAME, - (void *)port); - if (retval) - return retval; + spin_lock_irqsave(&port->lock, flags); /* Disable the TX and RX */ writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS, - port->membase + CDNS_UART_CR_OFFSET); + port->membase + CDNS_UART_CR); /* Set the Control Register with TX/RX Enable, TX/RX Reset, * no break chars. */ writel(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST, - port->membase + CDNS_UART_CR_OFFSET); - - status = readl(port->membase + CDNS_UART_CR_OFFSET); + port->membase + CDNS_UART_CR); - /* Clear the RX disable and TX disable bits and then set the TX enable - * bit and RX enable bit to enable the transmitter and receiver. + /* + * Clear the RX disable bit and then set the RX enable bit to enable + * the receiver. */ - writel((status & ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS)) - | (CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN | - CDNS_UART_CR_STOPBRK), - port->membase + CDNS_UART_CR_OFFSET); + status = readl(port->membase + CDNS_UART_CR); + status &= CDNS_UART_CR_RX_DIS; + status |= CDNS_UART_CR_RX_EN; + writel(status, port->membase + CDNS_UART_CR); /* Set the Mode Register with normal mode,8 data bits,1 stop bit, * no parity. */ writel(CDNS_UART_MR_CHMODE_NORM | CDNS_UART_MR_STOPMODE_1_BIT | CDNS_UART_MR_PARITY_NONE | CDNS_UART_MR_CHARLEN_8_BIT, - port->membase + CDNS_UART_MR_OFFSET); + port->membase + CDNS_UART_MR); /* * Set the RX FIFO Trigger level to use most of the FIFO, but it * can be tuned with a module parameter */ - writel(rx_trigger_level, port->membase + CDNS_UART_RXWM_OFFSET); + writel(rx_trigger_level, port->membase + CDNS_UART_RXWM); /* * Receive Timeout register is enabled but it * can be tuned with a module parameter */ - writel(rx_timeout, port->membase + CDNS_UART_RXTOUT_OFFSET); + writel(rx_timeout, port->membase + CDNS_UART_RXTOUT); /* Clear out any pending interrupts before enabling them */ - writel(readl(port->membase + CDNS_UART_ISR_OFFSET), - port->membase + CDNS_UART_ISR_OFFSET); + writel(readl(port->membase + CDNS_UART_ISR), + port->membase + CDNS_UART_ISR); + + spin_unlock_irqrestore(&port->lock, flags); + + ret = request_irq(port->irq, cdns_uart_isr, 0, CDNS_UART_NAME, port); + if (ret) { + dev_err(port->dev, "request_irq '%d' failed with %d\n", + port->irq, ret); + return ret; + } /* Set the Interrupt Registers with desired interrupts */ - writel(CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_PARITY | - CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN | - CDNS_UART_IXR_RXTRIG | CDNS_UART_IXR_TOUT, - port->membase + CDNS_UART_IER_OFFSET); + writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IER); - return retval; + return 0; } /** @@ -819,14 +806,21 @@ static int cdns_uart_startup(struct uart_port *port) static void cdns_uart_shutdown(struct uart_port *port) { int status; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); /* Disable interrupts */ - status = readl(port->membase + CDNS_UART_IMR_OFFSET); - writel(status, port->membase + CDNS_UART_IDR_OFFSET); + status = readl(port->membase + CDNS_UART_IMR); + writel(status, port->membase + CDNS_UART_IDR); + writel(0xffffffff, port->membase + CDNS_UART_ISR); /* Disable the TX and RX */ writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS, - port->membase + CDNS_UART_CR_OFFSET); + port->membase + CDNS_UART_CR); + + spin_unlock_irqrestore(&port->lock, flags); + free_irq(port->irq, port); } @@ -928,7 +922,7 @@ static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) { u32 val; - val = readl(port->membase + CDNS_UART_MODEMCR_OFFSET); + val = readl(port->membase + CDNS_UART_MODEMCR); val &= ~(CDNS_UART_MODEMCR_RTS | CDNS_UART_MODEMCR_DTR); @@ -937,55 +931,46 @@ static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) if (mctrl & TIOCM_DTR) val |= CDNS_UART_MODEMCR_DTR; - writel(val, port->membase + CDNS_UART_MODEMCR_OFFSET); + writel(val, port->membase + CDNS_UART_MODEMCR); } #ifdef CONFIG_CONSOLE_POLL static int cdns_uart_poll_get_char(struct uart_port *port) { - u32 imr; int c; + unsigned long flags; - /* Disable all interrupts */ - imr = readl(port->membase + CDNS_UART_IMR_OFFSET); - writel(imr, port->membase + CDNS_UART_IDR_OFFSET); + spin_lock_irqsave(&port->lock, flags); /* Check if FIFO is empty */ - if (readl(port->membase + CDNS_UART_SR_OFFSET) & CDNS_UART_SR_RXEMPTY) + if (readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_RXEMPTY) c = NO_POLL_CHAR; else /* Read a character */ - c = (unsigned char) readl( - port->membase + CDNS_UART_FIFO_OFFSET); + c = (unsigned char) readl(port->membase + CDNS_UART_FIFO); - /* Enable interrupts */ - writel(imr, port->membase + CDNS_UART_IER_OFFSET); + spin_unlock_irqrestore(&port->lock, flags); return c; } static void cdns_uart_poll_put_char(struct uart_port *port, unsigned char c) { - u32 imr; + unsigned long flags; - /* Disable all interrupts */ - imr = readl(port->membase + CDNS_UART_IMR_OFFSET); - writel(imr, port->membase + CDNS_UART_IDR_OFFSET); + spin_lock_irqsave(&port->lock, flags); /* Wait until FIFO is empty */ - while (!(readl(port->membase + CDNS_UART_SR_OFFSET) & - CDNS_UART_SR_TXEMPTY)) + while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY)) cpu_relax(); /* Write a character */ - writel(c, port->membase + CDNS_UART_FIFO_OFFSET); + writel(c, port->membase + CDNS_UART_FIFO); /* Wait until FIFO is empty */ - while (!(readl(port->membase + CDNS_UART_SR_OFFSET) & - CDNS_UART_SR_TXEMPTY)) + while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY)) cpu_relax(); - /* Enable interrupts */ - writel(imr, port->membase + CDNS_UART_IER_OFFSET); + spin_unlock_irqrestore(&port->lock, flags); return; } @@ -1059,8 +1044,7 @@ static struct uart_port *cdns_uart_get_port(int id) */ static void cdns_uart_console_wait_tx(struct uart_port *port) { - while (!(readl(port->membase + CDNS_UART_SR_OFFSET) & - CDNS_UART_SR_TXEMPTY)) + while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY)) barrier(); } @@ -1072,7 +1056,7 @@ static void cdns_uart_console_wait_tx(struct uart_port *port) static void cdns_uart_console_putchar(struct uart_port *port, int ch) { cdns_uart_console_wait_tx(port); - writel(ch, port->membase + CDNS_UART_FIFO_OFFSET); + writel(ch, port->membase + CDNS_UART_FIFO); } static void __init cdns_early_write(struct console *con, const char *s, @@ -1093,7 +1077,9 @@ static int __init cdns_early_console_setup(struct earlycon_device *device, return 0; } -EARLYCON_DECLARE(cdns, cdns_early_console_setup); +OF_EARLYCON_DECLARE(cdns, "xlnx,xuartps", cdns_early_console_setup); +OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p8", cdns_early_console_setup); +OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p12", cdns_early_console_setup); /** * cdns_uart_console_write - perform write operation @@ -1109,30 +1095,33 @@ static void cdns_uart_console_write(struct console *co, const char *s, unsigned int imr, ctrl; int locked = 1; - if (oops_in_progress) + if (port->sysrq) + locked = 0; + else if (oops_in_progress) locked = spin_trylock_irqsave(&port->lock, flags); else spin_lock_irqsave(&port->lock, flags); /* save and disable interrupt */ - imr = readl(port->membase + CDNS_UART_IMR_OFFSET); - writel(imr, port->membase + CDNS_UART_IDR_OFFSET); + imr = readl(port->membase + CDNS_UART_IMR); + writel(imr, port->membase + CDNS_UART_IDR); /* * Make sure that the tx part is enabled. Set the TX enable bit and * clear the TX disable bit to enable the transmitter. */ - ctrl = readl(port->membase + CDNS_UART_CR_OFFSET); - writel((ctrl & ~CDNS_UART_CR_TX_DIS) | CDNS_UART_CR_TX_EN, - port->membase + CDNS_UART_CR_OFFSET); + ctrl = readl(port->membase + CDNS_UART_CR); + ctrl &= ~CDNS_UART_CR_TX_DIS; + ctrl |= CDNS_UART_CR_TX_EN; + writel(ctrl, port->membase + CDNS_UART_CR); uart_console_write(port, s, count, cdns_uart_console_putchar); cdns_uart_console_wait_tx(port); - writel(ctrl, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl, port->membase + CDNS_UART_CR); /* restore interrupt state */ - writel(imr, port->membase + CDNS_UART_IER_OFFSET); + writel(imr, port->membase + CDNS_UART_IER); if (locked) spin_unlock_irqrestore(&port->lock, flags); @@ -1244,14 +1233,13 @@ static int cdns_uart_suspend(struct device *device) spin_lock_irqsave(&port->lock, flags); /* Empty the receive FIFO 1st before making changes */ - while (!(readl(port->membase + CDNS_UART_SR_OFFSET) & + while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_RXEMPTY)) - readl(port->membase + CDNS_UART_FIFO_OFFSET); + readl(port->membase + CDNS_UART_FIFO); /* set RX trigger level to 1 */ - writel(1, port->membase + CDNS_UART_RXWM_OFFSET); + writel(1, port->membase + CDNS_UART_RXWM); /* disable RX timeout interrups */ - writel(CDNS_UART_IXR_TOUT, - port->membase + CDNS_UART_IDR_OFFSET); + writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IDR); spin_unlock_irqrestore(&port->lock, flags); } @@ -1290,30 +1278,28 @@ static int cdns_uart_resume(struct device *device) spin_lock_irqsave(&port->lock, flags); /* Set TX/RX Reset */ - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); - while (readl(port->membase + CDNS_UART_CR_OFFSET) & + writel(ctrl_reg, port->membase + CDNS_UART_CR); + while (readl(port->membase + CDNS_UART_CR) & (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST)) cpu_relax(); /* restore rx timeout value */ - writel(rx_timeout, port->membase + CDNS_UART_RXTOUT_OFFSET); + writel(rx_timeout, port->membase + CDNS_UART_RXTOUT); /* Enable Tx/Rx */ - ctrl_reg = readl(port->membase + CDNS_UART_CR_OFFSET); + ctrl_reg = readl(port->membase + CDNS_UART_CR); ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS); ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN; - writel(ctrl_reg, port->membase + CDNS_UART_CR_OFFSET); + writel(ctrl_reg, port->membase + CDNS_UART_CR); spin_unlock_irqrestore(&port->lock, flags); } else { spin_lock_irqsave(&port->lock, flags); /* restore original rx trigger level */ - writel(rx_trigger_level, - port->membase + CDNS_UART_RXWM_OFFSET); + writel(rx_trigger_level, port->membase + CDNS_UART_RXWM); /* enable RX timeout interrupt */ - writel(CDNS_UART_IXR_TOUT, - port->membase + CDNS_UART_IER_OFFSET); + writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IER); spin_unlock_irqrestore(&port->lock, flags); } @@ -1406,27 +1392,30 @@ static int cdns_uart_probe(struct platform_device *pdev) dev_err(&pdev->dev, "Cannot get uart_port structure\n"); rc = -ENODEV; goto err_out_notif_unreg; - } else { - /* Register the port. - * This function also registers this device with the tty layer - * and triggers invocation of the config_port() entry point. - */ - port->mapbase = res->start; - port->irq = irq; - port->dev = &pdev->dev; - port->uartclk = clk_get_rate(cdns_uart_data->uartclk); - port->private_data = cdns_uart_data; - cdns_uart_data->port = port; - platform_set_drvdata(pdev, port); - rc = uart_add_one_port(&cdns_uart_uart_driver, port); - if (rc) { - dev_err(&pdev->dev, - "uart_add_one_port() failed; err=%i\n", rc); - goto err_out_notif_unreg; - } - return 0; } + /* + * Register the port. + * This function also registers this device with the tty layer + * and triggers invocation of the config_port() entry point. + */ + port->mapbase = res->start; + port->irq = irq; + port->dev = &pdev->dev; + port->uartclk = clk_get_rate(cdns_uart_data->uartclk); + port->private_data = cdns_uart_data; + cdns_uart_data->port = port; + platform_set_drvdata(pdev, port); + + rc = uart_add_one_port(&cdns_uart_uart_driver, port); + if (rc) { + dev_err(&pdev->dev, + "uart_add_one_port() failed; err=%i\n", rc); + goto err_out_notif_unreg; + } + + return 0; + err_out_notif_unreg: #ifdef CONFIG_COMMON_CLK clk_notifier_unregister(cdns_uart_data->uartclk, diff --git a/drivers/tty/serial/zs.c b/drivers/tty/serial/zs.c index 2b65bb7ffb8a..eeefd76a30da 100644 --- a/drivers/tty/serial/zs.c +++ b/drivers/tty/serial/zs.c @@ -1181,6 +1181,10 @@ static void zs_console_write(struct console *co, const char *s, if (txint & TxINT_ENAB) { zport->regs[1] |= TxINT_ENAB; write_zsreg(zport, R1, zport->regs[1]); + + /* Resume any transmission as the TxIP bit won't be set. */ + if (!zport->tx_stopped) + zs_raw_transmit_chars(zport); } spin_unlock_irqrestore(&scc->zlock, flags); } |