diff options
Diffstat (limited to 'drivers/net/can/Kconfig')
| -rw-r--r-- | drivers/net/can/Kconfig | 30 |
1 files changed, 15 insertions, 15 deletions
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig index 17c166cc8482..f07012a76c0c 100644 --- a/drivers/net/can/Kconfig +++ b/drivers/net/can/Kconfig @@ -3,7 +3,7 @@ menu "CAN Device Drivers" config CAN_VCAN tristate "Virtual Local CAN Interface (vcan)" - ---help--- + help Similar to the network loopback devices, vcan offers a virtual local CAN interface. @@ -12,7 +12,7 @@ config CAN_VCAN config CAN_VXCAN tristate "Virtual CAN Tunnel (vxcan)" - ---help--- + help Similar to the virtual ethernet driver veth, vxcan implements a local CAN traffic tunnel between two virtual CAN network devices. When creating a vxcan, two vxcan devices are created as pair. @@ -31,7 +31,7 @@ config CAN_VXCAN config CAN_SLCAN tristate "Serial / USB serial CAN Adaptors (slcan)" depends on TTY - ---help--- + help CAN driver for several 'low cost' CAN interfaces that are attached via serial lines or via USB-to-serial adapters using the LAWICEL ASCII protocol. The driver implements the tty linediscipline N_SLCAN. @@ -51,7 +51,7 @@ config CAN_SLCAN config CAN_DEV tristate "Platform CAN drivers with Netlink support" default y - ---help--- + help Enables the common framework for platform CAN drivers with Netlink support. This is the standard library for CAN drivers. If unsure, say Y. @@ -61,7 +61,7 @@ if CAN_DEV config CAN_CALC_BITTIMING bool "CAN bit-timing calculation" default y - ---help--- + help If enabled, CAN bit-timing parameters will be calculated for the bit-rate specified via Netlink argument "bitrate" when the device get started. This works fine for the most common CAN controllers @@ -81,7 +81,7 @@ config CAN_LEDS # fulfills your needs instead of fixing this driver. depends on BROKEN select LEDS_TRIGGERS - ---help--- + help This option adds two LED triggers for packet receive and transmit events on each supported CAN device. @@ -91,20 +91,20 @@ config CAN_LEDS config CAN_AT91 tristate "Atmel AT91 onchip CAN controller" depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM - ---help--- + help This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 and AT91SAM9X5 processors. config CAN_FLEXCAN tristate "Support for Freescale FLEXCAN based chips" depends on OF && HAS_IOMEM - ---help--- + help Say Y here if you want to support for Freescale FlexCAN. config CAN_GRCAN tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" depends on OF && HAS_DMA - ---help--- + help Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. Note that the driver supports little endian, even though little endian syntheses of the cores would need some modifications on @@ -113,7 +113,7 @@ config CAN_GRCAN config CAN_JANZ_ICAN3 tristate "Janz VMOD-ICAN3 Intelligent CAN controller" depends on MFD_JANZ_CMODIO - ---help--- + help Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which connects to a MODULbus carrier board. @@ -136,7 +136,7 @@ config CAN_KVASER_PCIEFD config CAN_SUN4I tristate "Allwinner A10 CAN controller" depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST - ---help--- + help Say Y here if you want to use CAN controller found on Allwinner A10/A20 SoCs. @@ -146,7 +146,7 @@ config CAN_SUN4I config CAN_TI_HECC depends on ARM tristate "TI High End CAN Controller" - ---help--- + help Driver for TI HECC (High End CAN Controller) module found on many TI devices. The device specifications are available from www.ti.com @@ -154,14 +154,14 @@ config CAN_XILINXCAN tristate "Xilinx CAN" depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST depends on COMMON_CLK && HAS_IOMEM - ---help--- + help Xilinx CAN driver. This driver supports both soft AXI CAN IP and Zynq CANPS IP. config PCH_CAN tristate "Intel EG20T PCH CAN controller" depends on PCI && (X86_32 || COMPILE_TEST) - ---help--- + help This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which is an IOH for x86 embedded processor (Intel Atom E6xx series). This driver can access CAN bus. @@ -182,7 +182,7 @@ endif config CAN_DEBUG_DEVICES bool "CAN devices debugging messages" - ---help--- + help Say Y here if you want the CAN device drivers to produce a bunch of debug messages to the system log. Select this if you are having a problem with CAN support and want to see more of what is going |