diff options
Diffstat (limited to 'arch/avr32/boards/atngw100/mrmt.c')
| -rw-r--r-- | arch/avr32/boards/atngw100/mrmt.c | 382 |
1 files changed, 0 insertions, 382 deletions
diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c deleted file mode 100644 index 99b0a7984950..000000000000 --- a/arch/avr32/boards/atngw100/mrmt.c +++ /dev/null @@ -1,382 +0,0 @@ -/* - * Board-specific setup code for Remote Media Terminal 1 (RMT1) - * add-on board for the ATNGW100 Network Gateway - * - * Copyright (C) 2008 Mediama Technologies - * Based on ATNGW100 Network Gateway (Copyright (C) Atmel) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/gpio.h> -#include <linux/init.h> -#include <linux/irq.h> -#include <linux/linkage.h> -#include <linux/platform_device.h> -#include <linux/types.h> -#include <linux/fb.h> -#include <linux/leds.h> -#include <linux/pwm.h> -#include <linux/leds_pwm.h> -#include <linux/input.h> -#include <linux/gpio_keys.h> -#include <linux/spi/spi.h> -#include <linux/spi/ads7846.h> - -#include <video/atmel_lcdc.h> -#include <sound/atmel-ac97c.h> - -#include <asm/delay.h> -#include <asm/io.h> -#include <asm/setup.h> - -#include <mach/at32ap700x.h> -#include <mach/board.h> -#include <mach/init.h> -#include <mach/portmux.h> - -/* Define board-specifoic GPIO assignments */ -#define PIN_LCD_BL GPIO_PIN_PA(28) -#define PWM_CH_BL 0 /* Must match with GPIO pin definition */ -#define PIN_LCD_DISP GPIO_PIN_PA(31) -#define PIN_AC97_RST_N GPIO_PIN_PA(30) -#define PB_EXTINT_BASE 25 -#define TS_IRQ 0 -#define PIN_TS_EXTINT GPIO_PIN_PB(PB_EXTINT_BASE+TS_IRQ) -#define PIN_PB_LEFT GPIO_PIN_PB(11) -#define PIN_PB_RIGHT GPIO_PIN_PB(12) -#define PIN_PWR_SW_N GPIO_PIN_PB(14) -#define PIN_PWR_ON GPIO_PIN_PB(13) -#define PIN_ZB_RST_N GPIO_PIN_PA(21) -#define PIN_BT_RST GPIO_PIN_PA(22) -#define PIN_LED_SYS GPIO_PIN_PA(16) -#define PIN_LED_A GPIO_PIN_PA(19) -#define PIN_LED_B GPIO_PIN_PE(19) - -#ifdef CONFIG_BOARD_MRMT_LCD_LQ043T3DX0X -/* Sharp LQ043T3DX0x (or compatible) panel */ -static struct fb_videomode __initdata lcd_fb_modes[] = { - { - .name = "480x272 @ 59.94Hz", - .refresh = 59.94, - .xres = 480, .yres = 272, - .pixclock = KHZ2PICOS(9000), - - .left_margin = 2, .right_margin = 2, - .upper_margin = 3, .lower_margin = 9, - .hsync_len = 41, .vsync_len = 1, - - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED, - }, -}; - -static struct fb_monspecs __initdata lcd_fb_default_monspecs = { - .manufacturer = "SHA", - .monitor = "LQ043T3DX02", - .modedb = lcd_fb_modes, - .modedb_len = ARRAY_SIZE(lcd_fb_modes), - .hfmin = 14915, - .hfmax = 17638, - .vfmin = 53, - .vfmax = 61, - .dclkmax = 9260000, -}; - -static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = { - .default_bpp = 24, - .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN, - .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT - | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE - | ATMEL_LCDC_INVCLK_NORMAL - | ATMEL_LCDC_MEMOR_BIG), - .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB, - .default_monspecs = &lcd_fb_default_monspecs, - .guard_time = 2, -}; -#endif - -#ifdef CONFIG_BOARD_MRMT_LCD_KWH043GM08 -/* Sharp KWH043GM08-Fxx (or compatible) panel */ -static struct fb_videomode __initdata lcd_fb_modes[] = { - { - .name = "480x272 @ 59.94Hz", - .refresh = 59.94, - .xres = 480, .yres = 272, - .pixclock = KHZ2PICOS(9000), - - .left_margin = 2, .right_margin = 2, - .upper_margin = 3, .lower_margin = 9, - .hsync_len = 41, .vsync_len = 1, - - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED, - }, -}; - -static struct fb_monspecs __initdata lcd_fb_default_monspecs = { - .manufacturer = "FOR", - .monitor = "KWH043GM08", - .modedb = lcd_fb_modes, - .modedb_len = ARRAY_SIZE(lcd_fb_modes), - .hfmin = 14915, - .hfmax = 17638, - .vfmin = 53, - .vfmax = 61, - .dclkmax = 9260000, -}; - -static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = { - .default_bpp = 24, - .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN, - .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT - | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE - | ATMEL_LCDC_INVCLK_INVERTED - | ATMEL_LCDC_MEMOR_BIG), - .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB, - .default_monspecs = &lcd_fb_default_monspecs, - .guard_time = 2, -}; -#endif - -#ifdef CONFIG_BOARD_MRMT_AC97 -static struct ac97c_platform_data __initdata ac97c0_data = { - .reset_pin = PIN_AC97_RST_N, -}; -#endif - -#ifdef CONFIG_BOARD_MRMT_UCB1400_TS -/* NOTE: IRQ assignment relies on kernel module parameter */ -static struct platform_device rmt_ts_device = { - .name = "ucb1400_ts", - .id = -1, -}; -#endif - -#ifdef CONFIG_BOARD_MRMT_BL_PWM -/* PWM LEDs: LCD Backlight, etc */ -static struct pwm_lookup pwm_lookup[] = { - PWM_LOOKUP("at91sam9rl-pwm", PWM_CH_BL, "leds_pwm", "ds1", - 5000, PWM_POLARITY_INVERSED), -}; - -static struct led_pwm pwm_leds[] = { - { - .name = "backlight", - .max_brightness = 255, - }, -}; - -static struct led_pwm_platform_data pwm_data = { - .num_leds = ARRAY_SIZE(pwm_leds), - .leds = pwm_leds, -}; - -static struct platform_device leds_pwm = { - .name = "leds_pwm", - .id = -1, - .dev = { - .platform_data = &pwm_data, - }, -}; -#endif - -#ifdef CONFIG_BOARD_MRMT_ADS7846_TS -static int ads7846_pendown_state(void) -{ - return !gpio_get_value( PIN_TS_EXTINT ); /* PENIRQ.*/ -} - -static struct ads7846_platform_data ads_info = { - .model = 7846, - .keep_vref_on = 0, /* Use external VREF pin */ - .vref_delay_usecs = 0, - .vref_mv = 3300, /* VREF = 3.3V */ - .settle_delay_usecs = 800, - .penirq_recheck_delay_usecs = 800, - .x_plate_ohms = 750, - .y_plate_ohms = 300, - .pressure_max = 4096, - .debounce_max = 1, - .debounce_rep = 0, - .debounce_tol = (~0), - .get_pendown_state = ads7846_pendown_state, - .filter = NULL, - .filter_init = NULL, -}; - -static struct spi_board_info spi01_board_info[] __initdata = { - { - .modalias = "ads7846", - .max_speed_hz = 31250*26, - .bus_num = 0, - .chip_select = 1, - .platform_data = &ads_info, - .irq = AT32_EXTINT(TS_IRQ), - }, -}; -#endif - -/* GPIO Keys: left, right, power, etc */ -static const struct gpio_keys_button rmt_gpio_keys_buttons[] = { - [0] = { - .type = EV_KEY, - .code = KEY_POWER, - .gpio = PIN_PWR_SW_N, - .active_low = 1, - .desc = "power button", - }, - [1] = { - .type = EV_KEY, - .code = KEY_LEFT, - .gpio = PIN_PB_LEFT, - .active_low = 1, - .desc = "left button", - }, - [2] = { - .type = EV_KEY, - .code = KEY_RIGHT, - .gpio = PIN_PB_RIGHT, - .active_low = 1, - .desc = "right button", - }, -}; - -static const struct gpio_keys_platform_data rmt_gpio_keys_data = { - .nbuttons = ARRAY_SIZE(rmt_gpio_keys_buttons), - .buttons = (void *) rmt_gpio_keys_buttons, -}; - -static struct platform_device rmt_gpio_keys = { - .name = "gpio-keys", - .id = -1, - .dev = { - .platform_data = (void *) &rmt_gpio_keys_data, - } -}; - -#ifdef CONFIG_BOARD_MRMT_RTC_I2C -static struct i2c_board_info __initdata mrmt1_i2c_rtc = { - I2C_BOARD_INFO("s35390a", 0x30), - .irq = 0, -}; -#endif - -static void mrmt_power_off(void) -{ - /* PWR_ON=0 will force power off */ - gpio_set_value( PIN_PWR_ON, 0 ); -} - -static int __init mrmt1_init(void) -{ - gpio_set_value( PIN_PWR_ON, 1 ); /* Ensure PWR_ON is enabled */ - - pm_power_off = mrmt_power_off; - - /* Setup USARTS (other than console) */ - at32_map_usart(2, 1, 0); /* USART 2: /dev/ttyS1, RMT1:DB9M */ - at32_map_usart(3, 2, ATMEL_USART_RTS | ATMEL_USART_CTS); - /* USART 3: /dev/ttyS2, RMT1:Wireless, w/ RTS/CTS */ - at32_add_device_usart(1); - at32_add_device_usart(2); - - /* Select GPIO Key pins */ - at32_select_gpio( PIN_PWR_SW_N, AT32_GPIOF_DEGLITCH); - at32_select_gpio( PIN_PB_LEFT, AT32_GPIOF_DEGLITCH); - at32_select_gpio( PIN_PB_RIGHT, AT32_GPIOF_DEGLITCH); - platform_device_register(&rmt_gpio_keys); - -#ifdef CONFIG_BOARD_MRMT_RTC_I2C - i2c_register_board_info(0, &mrmt1_i2c_rtc, 1); -#endif - -#ifndef CONFIG_BOARD_MRMT_LCD_DISABLE - /* User "alternate" LCDC inferface on Port E & D */ - /* NB: exclude LCDC_CC pin, as NGW100 reserves it for other use */ - at32_add_device_lcdc(0, &rmt_lcdc_data, - fbmem_start, fbmem_size, - (ATMEL_LCDC_ALT_24BIT | ATMEL_LCDC_PE_DVAL ) ); -#endif - -#ifdef CONFIG_BOARD_MRMT_AC97 - at32_add_device_ac97c(0, &ac97c0_data, AC97C_BOTH); -#endif - -#ifdef CONFIG_BOARD_MRMT_ADS7846_TS - /* Select the Touchscreen interrupt pin mode */ - at32_select_periph( GPIO_PIOB_BASE, 1 << (PB_EXTINT_BASE+TS_IRQ), - GPIO_PERIPH_A, AT32_GPIOF_DEGLITCH); - irq_set_irq_type(AT32_EXTINT(TS_IRQ), IRQ_TYPE_EDGE_FALLING); - at32_spi_setup_slaves(0,spi01_board_info,ARRAY_SIZE(spi01_board_info)); - spi_register_board_info(spi01_board_info,ARRAY_SIZE(spi01_board_info)); -#endif - -#ifdef CONFIG_BOARD_MRMT_UCB1400_TS - /* Select the Touchscreen interrupt pin mode */ - at32_select_periph( GPIO_PIOB_BASE, 1 << (PB_EXTINT_BASE+TS_IRQ), - GPIO_PERIPH_A, AT32_GPIOF_DEGLITCH); - platform_device_register(&rmt_ts_device); -#endif - - at32_select_gpio( PIN_LCD_DISP, AT32_GPIOF_OUTPUT ); - gpio_request( PIN_LCD_DISP, "LCD_DISP" ); - gpio_direction_output( PIN_LCD_DISP, 0 ); /* LCD DISP */ -#ifdef CONFIG_BOARD_MRMT_LCD_DISABLE - /* Keep Backlight and DISP off */ - at32_select_gpio( PIN_LCD_BL, AT32_GPIOF_OUTPUT ); - gpio_request( PIN_LCD_BL, "LCD_BL" ); - gpio_direction_output( PIN_LCD_BL, 0 ); /* Backlight */ -#else - gpio_set_value( PIN_LCD_DISP, 1 ); /* DISP asserted first */ -#ifdef CONFIG_BOARD_MRMT_BL_PWM - /* Use PWM for Backlight controls */ - at32_add_device_pwm(1 << PWM_CH_BL); - pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup)); - platform_device_register(&leds_pwm); -#else - /* Backlight always on */ - udelay( 1 ); - at32_select_gpio( PIN_LCD_BL, AT32_GPIOF_OUTPUT ); - gpio_request( PIN_LCD_BL, "LCD_BL" ); - gpio_direction_output( PIN_LCD_BL, 1 ); -#endif -#endif - - /* Make sure BT and Zigbee modules in reset */ - at32_select_gpio( PIN_BT_RST, AT32_GPIOF_OUTPUT ); - gpio_request( PIN_BT_RST, "BT_RST" ); - gpio_direction_output( PIN_BT_RST, 1 ); - /* BT Module in Reset */ - - at32_select_gpio( PIN_ZB_RST_N, AT32_GPIOF_OUTPUT ); - gpio_request( PIN_ZB_RST_N, "ZB_RST_N" ); - gpio_direction_output( PIN_ZB_RST_N, 0 ); - /* XBee Module in Reset */ - -#ifdef CONFIG_BOARD_MRMT_WIRELESS_ZB - udelay( 1000 ); - /* Unreset the XBee Module */ - gpio_set_value( PIN_ZB_RST_N, 1 ); -#endif -#ifdef CONFIG_BOARD_MRMT_WIRELESS_BT - udelay( 1000 ); - /* Unreset the BT Module */ - gpio_set_value( PIN_BT_RST, 0 ); -#endif - - return 0; -} -arch_initcall(mrmt1_init); - -static int __init mrmt1_early_init(void) -{ - /* To maintain power-on signal in case boot loader did not already */ - at32_select_gpio( PIN_PWR_ON, AT32_GPIOF_OUTPUT ); - gpio_request( PIN_PWR_ON, "PIN_PWR_ON" ); - gpio_direction_output( PIN_PWR_ON, 1 ); - - return 0; -} -core_initcall(mrmt1_early_init); |