diff options
Diffstat (limited to 'Documentation')
27 files changed, 618 insertions, 40 deletions
diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt new file mode 100644 index 000000000000..3dfc2515e5c6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt @@ -0,0 +1,23 @@ +* Amlogic Audio FIFO controllers + +Required properties: +- compatible: 'amlogic,axg-toddr' or + 'amlogic,axg-frddr' +- reg: physical base address of the controller and length of memory + mapped region. +- interrupts: interrupt specifier for the fifo. +- clocks: phandle to the fifo peripheral clock provided by the audio + clock controller. +- resets: phandle to memory ARB line provided by the arb reset controller. +- #sound-dai-cells: must be 0. + +Example of FRDDR A on the A113 SoC: + +frddr_a: audio-controller@1c0 { + compatible = "amlogic,axg-frddr"; + reg = <0x0 0x1c0 0x0 0x1c>; + #sound-dai-cells = <0>; + interrupts = <GIC_SPI 88 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc_audio AUD_CLKID_FRDDR_A>; + resets = <&arb AXG_ARB_FRDDR_A>; +}; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-sound-card.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-sound-card.txt new file mode 100644 index 000000000000..80b411296480 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-sound-card.txt @@ -0,0 +1,124 @@ +Amlogic AXG sound card: + +Required properties: + +- compatible: "amlogic,axg-sound-card" +- model : User specified audio sound card name, one string + +Optional properties: + +- audio-aux-devs : List of phandles pointing to auxiliary devices +- audio-widgets : Please refer to widgets.txt. +- audio-routing : A list of the connections between audio components. + +Subnodes: + +- dai-link: Container for dai-link level properties and the CODEC + sub-nodes. There should be at least one (and probably more) + subnode of this type. + +Required dai-link properties: + +- sound-dai: phandle and port of the CPU DAI. + +Required TDM Backend dai-link properties: +- dai-format : CPU/CODEC common audio format + +Optional TDM Backend dai-link properties: +- dai-tdm-slot-rx-mask-{0,1,2,3}: Receive direction slot masks +- dai-tdm-slot-tx-mask-{0,1,2,3}: Transmit direction slot masks + When omitted, mask is assumed to have to no + slots. A valid must have at one slot, so at + least one these mask should be provided with + an enabled slot. +- dai-tdm-slot-num : Please refer to tdm-slot.txt. + If omitted, slot number is set to accommodate the largest + mask provided. +- dai-tdm-slot-width : Please refer to tdm-slot.txt. default to 32 if omitted. +- mclk-fs : Multiplication factor between stream rate and mclk + +Backend dai-link subnodes: + +- codec: dai-link representing backend links should have at least one subnode. + One subnode for each codec of the dai-link. + dai-link representing frontend links have no codec, therefore have no + subnodes + +Required codec subnodes properties: + +- sound-dai: phandle and port of the CODEC DAI. + +Optional codec subnodes properties: + +- dai-tdm-slot-tx-mask : Please refer to tdm-slot.txt. +- dai-tdm-slot-rx-mask : Please refer to tdm-slot.txt. + +Example: + +sound { + compatible = "amlogic,axg-sound-card"; + model = "AXG-S420"; + audio-aux-devs = <&tdmin_a>, <&tdmout_c>; + audio-widgets = "Line", "Lineout", + "Line", "Linein", + "Speaker", "Speaker1 Left", + "Speaker", "Speaker1 Right"; + "Speaker", "Speaker2 Left", + "Speaker", "Speaker2 Right"; + audio-routing = "TDMOUT_C IN 0", "FRDDR_A OUT 2", + "SPDIFOUT IN 0", "FRDDR_A OUT 3", + "TDM_C Playback", "TDMOUT_C OUT", + "TDMIN_A IN 2", "TDM_C Capture", + "TDMIN_A IN 5", "TDM_C Loopback", + "TODDR_A IN 0", "TDMIN_A OUT", + "Lineout", "Lineout AOUTL", + "Lineout", "Lineout AOUTR", + "Speaker1 Left", "SPK1 OUT_A", + "Speaker2 Left", "SPK2 OUT_A", + "Speaker1 Right", "SPK1 OUT_B", + "Speaker2 Right", "SPK2 OUT_B", + "Linein AINL", "Linein", + "Linein AINR", "Linein"; + + dai-link@0 { + sound-dai = <&frddr_a>; + }; + + dai-link@1 { + sound-dai = <&toddr_a>; + }; + + dai-link@2 { + sound-dai = <&tdmif_c>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + dai-tdm-slot-rx-mask-1 = <1 1>; + mclk-fs = <256>; + + codec@0 { + sound-dai = <&lineout>; + }; + + codec@1 { + sound-dai = <&speaker_amp1>; + }; + + codec@2 { + sound-dai = <&speaker_amp2>; + }; + + codec@3 { + sound-dai = <&linein>; + }; + + }; + + dai-link@3 { + sound-dai = <&spdifout>; + + codec { + sound-dai = <&spdif_dit>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt new file mode 100644 index 000000000000..521c38ad89e7 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt @@ -0,0 +1,20 @@ +* Amlogic Audio SPDIF Output + +Required properties: +- compatible: 'amlogic,axg-spdifout' +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "mclk" : master clock +- #sound-dai-cells: must be 0. + +Example on the A113 SoC: + +spdifout: audio-controller@480 { + compatible = "amlogic,axg-spdifout"; + reg = <0x0 0x480 0x0 0x50>; + #sound-dai-cells = <0>; + clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>, + <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>; + clock-names = "pclk", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt new file mode 100644 index 000000000000..1c1b7490554e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt @@ -0,0 +1,28 @@ +* Amlogic Audio TDM formatters + +Required properties: +- compatible: 'amlogic,axg-tdmin' or + 'amlogic,axg-tdmout' +- reg: physical base address of the controller and length of memory + mapped region. +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "sclk" : bit clock. + * "sclk_sel" : bit clock input multiplexer. + * "lrclk" : sample clock + * "lrclk_sel": sample clock input multiplexer + +Example of TDMOUT_A on the A113 SoC: + +tdmout_a: audio-controller@500 { + compatible = "amlogic,axg-tdmout"; + reg = <0x0 0x500 0x0 0x40>; + clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>, + <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; +}; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.txt new file mode 100644 index 000000000000..cabfb26a5f22 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.txt @@ -0,0 +1,22 @@ +* Amlogic Audio TDM Interfaces + +Required properties: +- compatible: 'amlogic,axg-tdm-iface' +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "sclk" : bit clock. + * "lrclk": sample clock + * "mclk" : master clock + -> optional if the interface is in clock slave mode. +- #sound-dai-cells: must be 0. + +Example of TDM_A on the A113 SoC: + +tdmif_a: audio-controller@0 { + compatible = "amlogic,axg-tdm-iface"; + #sound-dai-cells = <0>; + clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>, + <&clkc_audio AUD_CLKID_MST_A_SCLK>, + <&clkc_audio AUD_CLKID_MST_A_LRCLK>; + clock-names = "mclk", "sclk", "lrclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/atmel-i2s.txt b/Documentation/devicetree/bindings/sound/atmel-i2s.txt index 735368b8a73f..40549f496a81 100644 --- a/Documentation/devicetree/bindings/sound/atmel-i2s.txt +++ b/Documentation/devicetree/bindings/sound/atmel-i2s.txt @@ -15,7 +15,6 @@ Required properties: - clock-names: Should be one of each entry matching the clocks phandles list: - "pclk" (peripheral clock) Required. - "gclk" (generated clock) Optional (1). - - "aclk" (Audio PLL clock) Optional (1). - "muxclk" (I2S mux clock) Optional (1). Optional properties: @@ -23,9 +22,9 @@ Optional properties: - princtrl-names: Should contain only one value - "default". -(1) : Only the peripheral clock is required. The generated clock, the Audio - PLL clock adn the I2S mux clock are optional and should only be set - together, when Master Mode is required. +(1) : Only the peripheral clock is required. The generated clock and the I2S + mux clock are optional and should only be set together, when Master Mode + is required. Example: @@ -40,8 +39,8 @@ Example: (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(32))>; dma-names = "tx", "rx"; - clocks = <&i2s0_clk>, <&i2s0_gclk>, <&audio_pll_pmc>, <&i2s0muxck>; - clock-names = "pclk", "gclk", "aclk", "muxclk"; + clocks = <&i2s0_clk>, <&i2s0_gclk>, <&i2s0muxck>; + clock-names = "pclk", "gclk", "muxclk"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2s0_default>; }; diff --git a/Documentation/devicetree/bindings/sound/audio-graph-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-card.txt index d04ea3b1a1dd..7e63e53a901c 100644 --- a/Documentation/devicetree/bindings/sound/audio-graph-card.txt +++ b/Documentation/devicetree/bindings/sound/audio-graph-card.txt @@ -18,6 +18,8 @@ Below are same as Simple-Card. - bitclock-inversion - frame-inversion - mclk-fs +- hp-det-gpio +- mic-det-gpio - dai-tdm-slot-num - dai-tdm-slot-width - clocks / system-clock-frequency diff --git a/Documentation/devicetree/bindings/sound/dioo,dio2125.txt b/Documentation/devicetree/bindings/sound/dioo,dio2125.txt deleted file mode 100644 index 63dbfe0f11d0..000000000000 --- a/Documentation/devicetree/bindings/sound/dioo,dio2125.txt +++ /dev/null @@ -1,12 +0,0 @@ -DIO2125 Audio Driver - -Required properties: -- compatible : "dioo,dio2125" -- enable-gpios : the gpio connected to the enable pin of the dio2125 - -Example: - -amp: analog-amplifier { - compatible = "dioo,dio2125"; - enable-gpios = <&gpio GPIOH_3 0>; -}; diff --git a/Documentation/devicetree/bindings/sound/everest,es7134.txt b/Documentation/devicetree/bindings/sound/everest,es7134.txt index 5495a3cb8b7b..091666069bde 100644 --- a/Documentation/devicetree/bindings/sound/everest,es7134.txt +++ b/Documentation/devicetree/bindings/sound/everest,es7134.txt @@ -1,10 +1,15 @@ ES7134 i2s DA converter Required properties: -- compatible : "everest,es7134" or "everest,es7144" +- compatible : "everest,es7134" or + "everest,es7144" or + "everest,es7154" +- VDD-supply : regulator phandle for the VDD supply +- PVDD-supply: regulator phandle for the PVDD supply for the es7154 Example: i2s_codec: external-codec { compatible = "everest,es7134"; + VDD-supply = <&vcc_5v>; }; diff --git a/Documentation/devicetree/bindings/sound/everest,es7241.txt b/Documentation/devicetree/bindings/sound/everest,es7241.txt new file mode 100644 index 000000000000..28f82cf4959f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/everest,es7241.txt @@ -0,0 +1,28 @@ +ES7241 i2s AD converter + +Required properties: +- compatible : "everest,es7241" +- VDDP-supply: regulator phandle for the VDDA supply +- VDDA-supply: regulator phandle for the VDDP supply +- VDDD-supply: regulator phandle for the VDDD supply + +Optional properties: +- reset-gpios: gpio connected to the reset pin +- m0-gpios : gpio connected to the m0 pin +- m1-gpios : gpio connected to the m1 pin +- everest,sdout-pull-down: + Format used by the serial interface is controlled by pulling + the sdout. If the sdout is pulled down, leftj format is used. + If this property is not provided, sdout is assumed to pulled + up and i2s format is used + +Example: + +linein: audio-codec@2 { + #sound-dai-cells = <0>; + compatible = "everest,es7241"; + VDDA-supply = <&vcc_3v3>; + VDDP-supply = <&vcc_3v3>; + VDDD-supply = <&vcc_3v3>; + reset-gpios = <&gpio GPIOH_42>; +}; diff --git a/Documentation/devicetree/bindings/sound/marvell,pxa2xx-ac97.txt b/Documentation/devicetree/bindings/sound/marvell,pxa2xx-ac97.txt new file mode 100644 index 000000000000..2ea85d5be6a4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/marvell,pxa2xx-ac97.txt @@ -0,0 +1,27 @@ +Marvell PXA2xx audio complex + +This descriptions matches the AC97 controller found in pxa2xx and pxa3xx series. + +Required properties: + - compatible: should be one of the following: + "marvell,pxa250-ac97" + "marvell,pxa270-ac97" + "marvell,pxa300-ac97" + - reg: device MMIO address space + - interrupts: single interrupt generated by AC97 IP + - clocks: input clock of the AC97 IP, refer to clock-bindings.txt + +Optional properties: + - pinctrl-names, pinctrl-0: refer to pinctrl-bindings.txt + - reset-gpios: gpio used for AC97 reset, refer to gpio.txt + +Example: + ac97: sound@40500000 { + compatible = "marvell,pxa250-ac97"; + reg = < 0x40500000 0x1000 >; + interrupts = <14>; + reset-gpios = <&gpio 113 GPIO_ACTIVE_HIGH>; + #sound-dai-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = < &pmux_ac97_default >; + }; diff --git a/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt b/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt index 74c9ba6c2823..93b982e9419f 100644 --- a/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt +++ b/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt @@ -5,6 +5,14 @@ Required properties: compatible Must be "mrvl,pxa-ssp-dai" port A phandle reference to a PXA ssp upstream device +Optional properties: + + clock-names + clocks Through "clock-names" and "clocks", external clocks + can be configured. If a clock names "extclk" exists, + it will be set to the mclk rate of the audio stream + and be used as clock provider of the DAI. + Example: /* upstream device */ diff --git a/Documentation/devicetree/bindings/sound/mrvl,pxa2xx-pcm.txt b/Documentation/devicetree/bindings/sound/mrvl,pxa2xx-pcm.txt deleted file mode 100644 index 551fbb8348c2..000000000000 --- a/Documentation/devicetree/bindings/sound/mrvl,pxa2xx-pcm.txt +++ /dev/null @@ -1,15 +0,0 @@ -DT bindings for ARM PXA2xx PCM platform driver - -This is just a dummy driver that registers the PXA ASoC platform driver. -It does not have any resources assigned. - -Required properties: - - - compatible 'mrvl,pxa-pcm-audio' - -Example: - - pxa_pcm_audio: snd_soc_pxa_audio { - compatible = "mrvl,pxa-pcm-audio"; - }; - diff --git a/Documentation/devicetree/bindings/sound/name-prefix.txt b/Documentation/devicetree/bindings/sound/name-prefix.txt new file mode 100644 index 000000000000..645775908657 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/name-prefix.txt @@ -0,0 +1,24 @@ +Name prefix: + +Card implementing the routing property define the connection between +audio components as list of string pair. Component using the same +sink/source names may use the name prefix property to prepend the +name of their sinks/sources with the provided string. + +Optional name prefix property: +- sound-name-prefix : string using as prefix for the sink/source names of + the component. + +Example: Two instances of the same component. + +amp0: analog-amplifier@0 { + compatible = "simple-audio-amplifier"; + enable-gpios = <&gpio GPIOH_3 0>; + sound-name-prefix = "FRONT"; +}; + +amp1: analog-amplifier@1 { + compatible = "simple-audio-amplifier"; + enable-gpios = <&gpio GPIOH_4 0>; + sound-name-prefix = "BACK"; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8096.txt b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt index c7600a93ab39..c814e867850f 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8096.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt @@ -7,7 +7,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio. Value type: <stringlist> Definition: must be "qcom,apq8096-sndcard" -- qcom,audio-routing: +- audio-routing: Usage: Optional Value type: <stringlist> Definition: A list of the connections between audio components. @@ -49,6 +49,12 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio. "DMIC1" "DMIC2" "DMIC3" + +- model: + Usage: required + Value type: <stringlist> + Definition: The user-visible name of this sound card. + = dailinks Each subnode of sndcard represents either a dailink, and subnodes of each dailinks would be cpu/codec/platform dais. @@ -79,11 +85,16 @@ dailinks would be cpu/codec/platform dais. Value type: <phandle with arguments> Definition: dai phandle/s and port of CPU/CODEC/PLATFORM node. +Obsolete: + qcom,model: String for soundcard name (Use model instead) + qcom,audio-routing: A list of the connections between audio components. + (Use audio-routing instead) + Example: audio { compatible = "qcom,apq8096-sndcard"; - qcom,model = "DB820c"; + model = "DB820c"; mm1-dai-link { link-name = "MultiMedia1"; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6adm.txt b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt index cb709e5dbc44..bbae426cdfb1 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6adm.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt @@ -18,6 +18,11 @@ used by the apr service device. = ADM routing "routing" subnode of the ADM node represents adm routing specific configuration +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6adm-routing". + - #sound-dai-cells Usage: required Value type: <u32> @@ -28,6 +33,7 @@ q6adm@8 { compatible = "qcom,q6adm"; reg = <APR_SVC_ADM>; q6routing: routing { + compatible = "qcom,q6adm-routing"; #sound-dai-cells = <0>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt index bdbf87df8c0b..a8179409c194 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt @@ -17,6 +17,11 @@ used by all apr services. Must contain the following properties. subnode of "dais" representing board specific dai setup. "dais" node should have following properties followed by dai children. +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6afe-dais" + - #sound-dai-cells Usage: required Value type: <u32> @@ -100,6 +105,7 @@ q6afe@4 { reg = <APR_SVC_AFE>; dais { + compatible = "qcom,q6afe-dais"; #sound-dai-cells = <1>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt index 2178eb91146f..f9c7bd8c1bc0 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt @@ -17,6 +17,11 @@ used by the apr service device. = ASM DAIs (Digial Audio Interface) "dais" subnode of the ASM node represents dai specific configuration +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6asm-dais". + - #sound-dai-cells Usage: required Value type: <u32> @@ -28,6 +33,7 @@ q6asm@7 { compatible = "qcom,q6asm"; reg = <APR_SVC_ASM>; q6asmdai: dais { + compatible = "qcom,q6asm-dais"; #sound-dai-cells = <1>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,sdm845.txt b/Documentation/devicetree/bindings/sound/qcom,sdm845.txt new file mode 100644 index 000000000000..408c4837e6d5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,sdm845.txt @@ -0,0 +1,80 @@ +* Qualcomm Technologies Inc. SDM845 ASoC sound card driver + +This binding describes the SDM845 sound card, which uses qdsp for audio. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,sdm845-sndcard" + +- audio-routing: + Usage: Optional + Value type: <stringlist> + Definition: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, MicBias + of codec and the jacks on the board. + +- model: + Usage: required + Value type: <stringlist> + Definition: The user-visible name of this sound card. + += dailinks +Each subnode of sndcard represents either a dailink, and subnodes of each +dailinks would be cpu/codec/platform dais. + +- link-name: + Usage: required + Value type: <string> + Definition: User friendly name for dai link + += CPU, PLATFORM, CODEC dais subnodes +- cpu: + Usage: required + Value type: <subnode> + Definition: cpu dai sub-node + +- codec: + Usage: required + Value type: <subnode> + Definition: codec dai sub-node + +- platform: + Usage: Optional + Value type: <subnode> + Definition: platform dai sub-node + +- sound-dai: + Usage: required + Value type: <phandle> + Definition: dai phandle/s and port of CPU/CODEC/PLATFORM node. + +Example: + +audio { + compatible = "qcom,sdm845-sndcard"; + model = "sdm845-snd-card"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&pri_mi2s_active &pri_mi2s_ws_active>; + pinctrl-1 = <&pri_mi2s_sleep &pri_mi2s_ws_sleep>; + + mm1-dai-link { + link-name = "MultiMedia1"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; + }; + }; + + pri-mi2s-dai-link { + link-name = "PRI MI2S Playback"; + cpu { + sound-dai = <&q6afedai PRIMARY_MI2S_RX>; + }; + + platform { + sound-dai = <&q6routing>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt b/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt new file mode 100644 index 000000000000..1d8d49e30af7 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt @@ -0,0 +1,123 @@ +QCOM WCD9335 Codec + +Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC, supports +Qualcomm Technologies, Inc. (QTI) multimedia solutions, including +the MSM8996, MSM8976, and MSM8956 chipsets. It has in-built +Soundwire controller, interrupt mux. It supports both I2S/I2C and +SLIMbus audio interfaces. + +Required properties with SLIMbus Interface: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: For SLIMbus interface it should be "slimMID,PID", + textual representation of Manufacturer ID, Product Code, + shall be in lower case hexadecimal with leading zeroes + suppressed. Refer to slimbus/bus.txt for details. + Should be: + "slim217,1a0" for MSM8996 and APQ8096 SoCs with SLIMbus. + +- reg + Usage: required + Value type: <u32 u32> + Definition: Should be ('Device index', 'Instance ID') + +- interrupts + Usage: required + Value type: <prop-encoded-array> + Definition: Interrupts via WCD INTR1 and INTR2 pins + +- interrupt-names: + Usage: required + Value type: <String array> + Definition: Interrupt names of WCD INTR1 and INTR2 + Should be: "intr1", "intr2" + +- reset-gpio: + Usage: required + Value type: <String Array> + Definition: Reset gpio line + +- qcom,ifd: + Usage: required + Value type: <phandle> + Definition: SLIM interface device + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: See clock-bindings.txt section "consumers". List of + three clock specifiers for mclk, mclk2 and slimbus clock. + +- clock-names: + Usage: required + Value type: <string> + Definition: Must contain "mclk", "mclk2" and "slimbus" strings. + +- vdd-buck-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 1.8V buck supply + +- vdd-buck-sido-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 1.8V SIDO buck supply + +- vdd-rx-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 1.8V rx supply + +- vdd-tx-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 1.8V tx supply + +- vdd-vbat-supply: + Usage: Optional + Value type: <phandle> + Definition: Should contain a reference to the vbat supply + +- vdd-micbias-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the micbias supply + +- vdd-io-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 1.8V io supply + +- interrupt-controller: + Usage: required + Definition: Indicating that this is a interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <int> + Definition: should be 1 + +#sound-dai-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + +codec@1{ + compatible = "slim217,1a0"; + reg = <1 0>; + interrupts = <&msmgpio 54 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "intr2" + reset-gpio = <&msmgpio 64 0>; + qcom,ifd = <&wc9335_ifd>; + clock-names = "mclk", "native"; + clocks = <&rpmcc RPM_SMD_DIV_CLK1>, + <&rpmcc RPM_SMD_BB_CLK1>; + vdd-buck-supply = <&pm8994_s4>; + vdd-rx-supply = <&pm8994_s4>; + vdd-buck-sido-supply = <&pm8994_s4>; + vdd-tx-supply = <&pm8994_s4>; + vdd-io-supply = <&pm8994_s4>; + #sound-dai-cells = <1>; +} diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index b86d790f630f..9e764270c36b 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -352,6 +352,7 @@ Required properties: - "renesas,rcar_sound-r8a7794" (R-Car E2) - "renesas,rcar_sound-r8a7795" (R-Car H3) - "renesas,rcar_sound-r8a7796" (R-Car M3-W) + - "renesas,rcar_sound-r8a77965" (R-Car M3-N) - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index b208a752576c..54aefab71f2c 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -7,6 +7,7 @@ Required properties: - compatible: should be one of the following: - "rockchip,rk3066-i2s": for rk3066 + - "rockchip,px30-i2s", "rockchip,rk3066-i2s": for px30 - "rockchip,rk3036-i2s", "rockchip,rk3066-i2s": for rk3036 - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 - "rockchip,rk3228-i2s", "rockchip,rk3066-i2s": for rk3228 diff --git a/Documentation/devicetree/bindings/sound/rt5682.txt b/Documentation/devicetree/bindings/sound/rt5682.txt new file mode 100644 index 000000000000..312e9a129530 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5682.txt @@ -0,0 +1,50 @@ +RT5682 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5682" or "realtek,rt5682i" + +- reg : The I2C address of the device. + +Optional properties: + +- interrupts : The CODEC's interrupt output. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO2 pin as dmic1 data pin + 2: using GPIO5 pin as dmic1 data pin + +- realtek,dmic1-clk-pin + 0: using GPIO1 pin as dmic1 clock pin + 1: using GPIO3 pin as dmic1 clock pin + +- realtek,jd-src + 0: No JD is used + 1: using JD1 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Pins on the device (for linking into audio routes) for RT5682: + + * DMIC L1 + * DMIC R1 + * IN1P + * HPOL + * HPOR + +Example: + +rt5682 { + compatible = "realtek,rt5682i"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(U, 6) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_HIGH>; + realtek,dmic1-data-pin = <1>; + realtek,dmic1-clk-pin = <1>; + realtek,jd-src = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 0f214457476f..9c58f724396a 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -17,7 +17,7 @@ Optional properties: - VDDD-supply : the regulator provider of VDDD -- micbias-resistor-k-ohms : the bias resistor to be used in kOmhs +- micbias-resistor-k-ohms : the bias resistor to be used in kOhms The resistor can take values of 2k, 4k or 8k. If set to 0 it will be off. If this node is not mentioned or if the value is unknown, then diff --git a/Documentation/devicetree/bindings/sound/simple-amplifier.txt b/Documentation/devicetree/bindings/sound/simple-amplifier.txt new file mode 100644 index 000000000000..8647edae7af0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/simple-amplifier.txt @@ -0,0 +1,12 @@ +Simple Amplifier Audio Driver + +Required properties: +- compatible : "dioo,dio2125" or "simple-audio-amplifier" +- enable-gpios : the gpio connected to the enable pin of the simple amplifier + +Example: + +amp: analog-amplifier { + compatible = "simple-audio-amplifier"; + enable-gpios = <&gpio GPIOH_3 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/tas571x.txt b/Documentation/devicetree/bindings/sound/tas571x.txt index b4959f10b74b..7c8fd37c2f9e 100644 --- a/Documentation/devicetree/bindings/sound/tas571x.txt +++ b/Documentation/devicetree/bindings/sound/tas571x.txt @@ -7,6 +7,7 @@ powerdown (optional). Required properties: - compatible: should be one of the following: + - "ti,tas5707" - "ti,tas5711", - "ti,tas5717", - "ti,tas5719", diff --git a/Documentation/sound/soc/dpcm.rst b/Documentation/sound/soc/dpcm.rst index 395e5a516282..fe61e02277f8 100644 --- a/Documentation/sound/soc/dpcm.rst +++ b/Documentation/sound/soc/dpcm.rst @@ -254,9 +254,7 @@ configuration. channels->min = channels->max = 2; /* set DAI0 to 16 bit */ - snd_mask_set(¶ms->masks[SNDRV_PCM_HW_PARAM_FORMAT - - SNDRV_PCM_HW_PARAM_FIRST_MASK], - SNDRV_PCM_FORMAT_S16_LE); + params_set_format(params, SNDRV_PCM_FORMAT_S16_LE); return 0; } |