diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
6 files changed, 202 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt index 6245c9b1a68b..4860eabd0f72 100644 --- a/Documentation/devicetree/bindings/mfd/cros-ec.txt +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -3,7 +3,7 @@ ChromeOS Embedded Controller Google's ChromeOS EC is a Cortex-M device which talks to the AP and implements various function such as keyboard and battery charging. -The EC can be connect through various means (I2C, SPI, LPC) and the +The EC can be connect through various means (I2C, SPI, LPC, RPMSG) and the compatible string used depends on the interface. Each connection method has its own driver which connects to the top level interface-agnostic EC driver. Other Linux driver (such as cros-ec-keyb for the matrix keyboard) connect to @@ -17,6 +17,9 @@ Required properties (SPI): - compatible: "google,cros-ec-spi" - reg: SPI chip select +Required properties (RPMSG): +- compatible: "google,cros-ec-rpmsg" + Optional properties (SPI): - google,cros-ec-spi-pre-delay: Some implementations of the EC need a little time to wake up from sleep before they can receive SPI transfers at a high diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt index a48df7c08ab0..41671e0dc26b 100644 --- a/Documentation/devicetree/bindings/mfd/lp87565.txt +++ b/Documentation/devicetree/bindings/mfd/lp87565.txt @@ -41,3 +41,39 @@ lp87565_pmic: pmic@60 { }; }; }; + +TI LP87561 PMIC: + +This is a single output 4-phase regulator configuration + +Required properties: + - compatible: "ti,lp87561-q1" + - reg: I2C slave address. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - xxx-in-supply: Phandle to parent supply node of each regulator + populated under regulators node. xxx should match + the supply_name populated in driver. +Example: + +lp87561_pmic: pmic@62 { + compatible = "ti,lp87561-q1"; + reg = <0x62>; + gpio-controller; + #gpio-cells = <2>; + + buck3210-in-supply = <&vsys_3v3>; + + regulators: regulators { + buck3210_reg: buck3210 { + /* VDD_CORE */ + regulator-name = "buck3210"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-always-on; + regulator-boot-on; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/madera.txt b/Documentation/devicetree/bindings/mfd/madera.txt index db3266088386..cad0f2800502 100644 --- a/Documentation/devicetree/bindings/mfd/madera.txt +++ b/Documentation/devicetree/bindings/mfd/madera.txt @@ -11,10 +11,14 @@ bindings/sound/madera.txt Required properties: - compatible : One of the following chip-specific strings: + "cirrus,cs47l15" "cirrus,cs47l35" "cirrus,cs47l85" "cirrus,cs47l90" "cirrus,cs47l91" + "cirrus,cs42l92" + "cirrus,cs47l92" + "cirrus,cs47l93" "cirrus,wm1840" - reg : I2C slave address when connected using I2C, chip select number when @@ -22,7 +26,7 @@ Required properties: - DCVDD-supply : Power supply for the device as defined in bindings/regulator/regulator.txt - Mandatory on CS47L35, CS47L90, CS47L91 + Mandatory on CS47L15, CS47L35, CS47L90, CS47L91, CS42L92, CS47L92, CS47L93 Optional on CS47L85, WM1840 - AVDD-supply, DBVDD1-supply, DBVDD2-supply, CPVDD1-supply, CPVDD2-supply : @@ -35,7 +39,7 @@ Required properties: (CS47L85, WM1840) - SPKVDD-supply : Power supply for the device - (CS47L35) + (CS47L15, CS47L35) - interrupt-controller : Indicates that this device is an interrupt controller diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 1683ec3245bc..04df07f6f793 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -3,11 +3,15 @@ RK8XX Power Management Integrated Circuit The rk8xx family current members: rk805 rk808 +rk809 +rk817 rk818 Required properties: - compatible: "rockchip,rk805" - compatible: "rockchip,rk808" +- compatible: "rockchip,rk809" +- compatible: "rockchip,rk817" - compatible: "rockchip,rk818" - reg: I2C slave address - interrupts: the interrupt outputs of the controller. @@ -45,6 +49,23 @@ Optional RK808 properties: the gpio controller. If DVS GPIOs aren't present, voltage changes will happen very quickly with no slow ramp time. +Optional shared RK809 and RK817 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc5-supply: The input supply for LDO_REG1, LDO_REG2, LDO_REG3 +- vcc6-supply: The input supply for LDO_REG4, LDO_REG5, LDO_REG6 +- vcc7-supply: The input supply for LDO_REG7, LDO_REG8, LDO_REG9 + +Optional RK809 properties: +- vcc8-supply: The input supply for SWITCH_REG1 +- vcc9-supply: The input supply for DCDC_REG5, SWITCH_REG2 + +Optional RK817 properties: +- vcc8-supply: The input supply for BOOST +- vcc9-supply: The input supply for OTG_SWITCH + Optional RK818 properties: - vcc1-supply: The input supply for DCDC_REG1 - vcc2-supply: The input supply for DCDC_REG2 @@ -86,6 +107,21 @@ number as described in RK808 datasheet. - SWITCH_REGn - valid values for n are 1 to 2 +Following regulators of the RK809 and RK817 PMIC blocks are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK809 and RK817 datasheets. + + - DCDC_REGn + - valid values for n are 1 to 5 for RK809. + - valid values for n are 1 to 4 for RK817. + - LDO_REGn + - valid values for n are 1 to 9 for RK809. + - valid values for n are 1 to 9 for RK817. + - SWITCH_REGn + - valid values for n are 1 to 2 for RK809. + - BOOST for RK817 + - OTG_SWITCH for RK817 + Following regulators of the RK818 PMIC block are supported. Note that the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO number as described in RK818 datasheet. @@ -98,6 +134,14 @@ number as described in RK818 datasheet. - HDMI_SWITCH - OTG_SWITCH +It is necessary to configure three pins for both the RK809 and RK817, the three +pins are "gpio_ts" "gpio_gt" "gpio_slp". + The gpio_gt and gpio_ts pins support the gpio function. + The gpio_slp pin is for controlling the pmic states, as below: + - reset + - power down + - sleep + Standard regulator bindings are used inside regulator subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for more details diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt new file mode 100644 index 000000000000..c3c02ce73cde --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt @@ -0,0 +1,102 @@ +* ROHM BD70528 Power Management Integrated Circuit bindings + +BD70528MWV is an ultra-low quiescent current general purpose, single-chip, +power management IC for battery-powered portable devices. The IC +integrates 3 ultra-low current consumption buck converters, 3 LDOs and 2 +LED Drivers. Also included are 4 GPIOs, a real-time clock (RTC), a 32kHz +clock gate, high-accuracy VREF for use with an external ADC, flexible +dual-input power path, 10 bit SAR ADC for battery temperature monitor and +1S battery charger with scalable charge currents. + +Required properties: + - compatible : Should be "rohm,bd70528" + - reg : I2C slave address. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : To indicate BD70528 acts as an interrupt controller. + - #interrupt-cells : Should be 2. Usage is compliant to the 2 cells + variant of ../interrupt-controller/interrupts.txt + - gpio-controller : To indicate BD70528 acts as a GPIO controller. + - #gpio-cells : Should be 2. The first cell is the pin number and + the second cell is used to specify flags. See + ../gpio/gpio.txt for more information. + - #clock-cells : Should be 0. + - regulators: : List of child nodes that specify the regulators. + Please see ../regulator/rohm,bd70528-regulator.txt + +Optional properties: + - clock-output-names : Should contain name for output clock. + +Example: +/* External oscillator */ +osc: oscillator { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <32768>; + clock-output-names = "osc"; +}; + +pmic: pmic@4b { + compatible = "rohm,bd70528"; + reg = <0x4b>; + interrupt-parent = <&gpio1>; + interrupts = <29 GPIO_ACTIVE_LOW>; + clocks = <&osc 0>; + #clock-cells = <0>; + clock-output-names = "bd70528-32k-out"; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + + regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-ramp-delay = <250>; + }; + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + }; + led_ldo1: LED_LDO1 { + regulator-name = "led_ldo1"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; + led_ldo2: LED_LDO2 { + regulator-name = "led_ldo2"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index d5f68ac78d15..f22d74c7a8db 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -8,6 +8,8 @@ and 6 LDOs. Datasheet for BD71837 is available at: https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e +Datasheet for BD71847 is available at: +https://www.rohm.com/datasheet/BD71847AMWV/bd71847amwv-e Required properties: - compatible : Should be "rohm,bd71837" for bd71837 @@ -38,6 +40,14 @@ target state is set to READY by default. If SNVS state is used the boot crucial regulators must have the regulator-always-on and regulator-boot-on properties set in regulator node. +- rohm,short-press-ms : Short press duration in milliseconds +- rohm,long-press-ms : Long press duration in milliseconds + +Configure the "short press" and "long press" timers for the power button. +Values are rounded to what hardware supports (500ms multiple for short and +1000ms multiple for long). If these properties are not present the existing +configuration (from bootloader or OTP) is not touched. + Example: /* external oscillator node */ |